1 Ver. 1.3 2007. 08 Model Name Using Similar Mechanism HCD-GNZ7D/GNZ8D/GNZ9D DVD DVD Mechanism Type CDM74HF-DVBU101//C Section Optical Pick-up Name KHM-310CAB/C2NP Tape Deck Model Name Using Similar Machanism NEW Section SERVICE MANUAL E Model HCD-GNZ77D/GNZ88D Amplifier section HCD-GNZ88D The following measured at AC 120, 127, 220, 240 V, 50/60 Hz DIN power output (rated) 75 W + 75 W (4 ohms at 1 kHz, DIN) Continuous RMS power output (reference) Front speaker: 100 W + 100 W (4 ohms at 1 kHz, 10% THD) Center speaker: 40 W (8 ohms at 1 kHz, 10% THD) Surround speaker: 40 W + 40 W (8 ohms at 1 kHz, 10% THD) HCD-GNZ77D The following measured at AC 120, 127, 220, 240 V, 50/60 Hz DIN power output (rated) 75 W + 75 W (4 ohms at 1 kHz, DIN) Continuous RMS power output (reference) 100 W + 100 W (4 ohms at 1 kHz, 10% THD) Inputs VIDEO INPUT (phono jacks): VIDEO: 1 Vp-p, 75 ohms AUDIO L/R: Voltage 250 mV, impedance 47 kilohms TV/SAT AUDIO IN L/R (phono jack): Voltage 250 mV/450 mV, impedance 47 kilohms SPECIFICATIONS Outputs VIDEO OUT (phono jack): max. output level 1 Vp-p, unbalanced, Sync negative load impedance 75 ohms COMPONENT VIDEO OUT: Y: 1 Vp-p, 75 ohms PB/CB: 0.7 Vp-p, 75 ohms PR/CR: 0.7 Vp-p, 75 ohms S-VIDEO OUT (4-pin/mini-DIN jack): Y: 1 Vp-p, unbalanced, Sync. negative C: 0.286 Vp-p, load impedance 75 ohms PHONES (stereo mini jack): Accepts headphones of 8 ohms or more FRONT SPEAKER: Use only the supplied speakers SURROUND SPEAKER (HCD-GNZ88D): Use only the supplied speakers CENTER SPEAKER (HCD-GNZ88D): Use only the supplied speakers SUB WOOFER OUT (phono jack): Voltage 250 mV, impedance 1 kilohm Sony Corporation Personal Audio Division Published by Sony Techno Create Corporation 9-887-258-04 2007H04-1 © 2007. 08 – Continued on next page – DVD DECK RECEIVER (Photo: HCD-GNZ77D) • HCD-GNZ77D/GNZ88D are the tuner, deck, DVD and amplifier section in MHC-GNZ77D/GNZ88D. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 19 HCD-GNZ77D/GNZ88D SECTION 3 TEST MODE [PANEL TEST MODE] • This mode is used to check the fluorescent indicator tube, LEDs, keys, VOLUME jog, model, destination, software version and VACS level. Procedure: 1. Press x button, [ILLUMINATION] button and [DISC 2] button simultaneously. 2. All LEDs and segments in fluorescent indicator tube are lighted up. All LEDs are lighted up in red color where the SUB WOOFER ON/OFF LED is lighted up in green color. 3. When you want to enter to the software version dispaly mode, press [DISC 1] button. The model information appears on the fluorescent indicator tube. Press [DISC 1] button again to view the destination information. 4. Each time [DISC 1] button is pressed, the display changes from MC version, SYS version, UI version, DVD version, CDMA version, CDMB version, ST version, TA version, TM version, TC version in this order, and returns to the model version display. 5. When [DISC 3] button is pressed while the version numbers are being displayed except model and destination, the date of the software creation appears. When [DISC 3] button is pressed again, the display returns to the software version display. When [DISC 1] button is pressed while the date of the software creation is being displayed, the date of the software creation is displayed in the same order of software version display. 6. Press [DISC 2] button, the key check mode is activated. 7. In the key check mode, the fluorescent indicator tube displays “K 0 V0”. Turn the [OPERATIONAL DIAL] clockwise; “K” value increases by one. Turn the [OPERATIONAL DIAL] counterclockwise; “K” value increases by one. Each time a button is pressed, “K” value increases. Press other keys on main unit to check whether the key is detected. However, once a button has been pressed, it is no longer taken into account. “V” value increases in the manner of 0, 1, 2, 3 ... if [VOLUME] knob is turned clockwise, or it decreases in the manner of 0, 9, 8, 7 ... if [VOLUME] knob is turned counterclockwise. 8. When [DISC 3] button is pressed after all LEDs and segments in fluorescent indicator tube light up, the fluorescent indicator tube displays “VACS A”. A is VACS level which is triggered by signal level. 9. When [DISC SKIP/EX-CHANGE] button is pressed after all LEDs and segments in fluorescent indicator tube light up, alternate segments in fluorescent indicator tube would light up. If you press [DISC SKIP/EX-CHANGE] button again, another half of alternate segments in fluorescent indicator tube would light up. When [DISC SKIP/EX-CHANGE] button is pressed again, all segments lights off. Press [DISC SKIP/EX-CHANGE] button again would cause all segments lights up. 10. To release from this mode, press three buttons in the same manner as step 1, or disconnect the power cord. [COMMON TEST MODE] • This mode is used to check operations of the respective sections of Amplifier and Tape. Procedure: • To enter Common Test Mode 1. Press x button, [ILLUMINATION] button and [DISC 3] button simultaneously. 2. The DVD ring indicators and the line below DVD ring indicator flash synchronously on the fluorescent indicator tube. The function is changed to TV where the function is changed to DVD. • Check of Amplifier 1. Press [EQ BAND/MEMORY] button repeatedly until a message “GEQ MAX” appears on the fluorescent indicator tube. GEQ increases to its maximum. 2. Press [EQ BAND/MEMORY] button repeatedly until a message “GEQ MIN” appears on the fluorescent indicator tube. GEQ decreases to its minimum. 3. Press [EQ BAND/MEMORY] button repeatedly until a message “GEQ FLAT” appears on the fluorescent indicator tube. GEQ is set to flat. 4. When the [VOLUME] knob is turned clockwise even slightly, the sound volume increases to its maximum and a message “VOLUME MAX” appears on the fluorescent indicator tube. 5. When the [VOLUME] knob is turned counterclockwise even slightly, the sound volume decreases to its minimum and a message “VOLUME MIN” appears on the fluorescent indicator tube. • Tape function 1. When a tape is inserted in Deck B and recording is started, the function is changed to TV automatically. The function is change to DVD automatically when a tape is inserted in Deck B and recording is started. When [CD SYNC] button is pressed during recording in function, ALC (Automatic Logic Control) is turned on. 2. During recording, press m button will stop the recording and the function is changed to TAPE B and rewind the tape in Deck B until the recording start position and playback of the tape in Deck B is started. If the [REC PAUSE/START] button is pressed for a pause and pressed again to resume recording during recording time, when the tape is rewind, the tape will be rewind until the position where the pause is applied. • To release from Common Test mode 1. To release from this mode, press ?/1 button. 2. The cold reset is enforced at the same time. [COLD RESET] • The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1. Press ?/1 button to turn on the system. 2. Press x button, [ILLUMINATION] button, and ?/1 button simultaneously. 3. The message “COLD RESET” appears on the fluorescent indicator tube. Then, the fluorescent indicator tube becomes blank for a while, and the system is reset. [VACS ON/OFF] • This mode is used to switch on and off the VACS (Variable Attenuation Control System). Procedure: 1. Press ?/1 button to turn on the system. 2. Press x button, [DIRECTION] button and [DISC 1] simultaneously. The message “VACS OFF” or “VACS ON” appears on the fluorescent indicator tube. [TUNER STEP CHANGE] • The step interval of AM channels can be toggled between 9 kHz and 10 kHz. This mode is not available for Saudi Arabia and Russia models. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 20 HCD-GNZ77D/GNZ88D Procedure: 1. Press ?/1 button to turn on the system. 2. Press [TUNER/BAND] button repeatedly to select the “AM”. 3. Press ?/1 button to turn off the system. 4. Press [ILLUMINATION] button and ?/1 button simultaneously. The system will turn on automatically. The message “AM 9K STEP” or “AM 10K STEP” appears on the fluorescent indicator tube and thus the channel step is changed. [DVD SHIP MODE (WITH MEMORY CLEAR)] • This mode moves the optical pick-up to the position durable to vibration and clears all data including preset data stored in the RAM to initial conditions. Use this mode when returning the set to the customer after repair. Procedure: 1. Press ?/1 button to turn on the system. 2. Select DVD function. 3. Press x button, [DIRECTION] button and ?/1 button simultaneously during “DVD NO DISC” condition. The system will turn off automatically. 4. After the “STANDBY” blinking display finishes, a message “MECHA LOCK” appears on the fluorescent indicator tube and the DVD ship mode is set. [DVD SHIP MODE (WITHOUT MEMORY CLEAR)] • This mode moves the optical pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair. Procedure: 1. Press ?/1 button to turn on the system. 2. Select DVD function. 3. Press [DVD] button and ?/1 button simultaneously during “DVD NO DISC” condition. The system will turn off automatically. 4. After the “STANDBY” blinking display finishes, a message “MECHA LOCK” appears on the fluorescent indicator tube and the DVD ship mode is set. [DVD TRAY LOCK MODE] • This mode let you lock the disc tray. When this mode is activated, the disc tray will not open when [OPEN/CLOSE] button or [DISC SKIP/EX-CHANGE] button is pressed. The message “LOCKED” will appears on the fluorescent indicator tube. Procedure: 1. Press ?/1 button to turn on the system. 2. Select DVD function. 3. Press x button and [OPEN/CLOSE] button simultaneously and hold down until “LOCKED” or “UNLOCKED” appears on the fluorescent indicator tube (around 5 seconds). [TCM OFFLINE MODE] • This mode prevents the system from turning off automatically when TCM is not connected. Therefore, measurements can be done even when TCM is not connected during production. Procedure: 1. When the system is turned off, press [EQ BAND/MEMORY] button, [TAPE A/B] button and ?/1 button simultaneously. The system will turn on automatically. 2. The message “TCM OFFLINE” will appears on the fluorescent indicator tube. • To release from TCM Offline Mode To release from this mode, perform “COLD RESET” or turn off the power supply. [TV/SAT SWITCHING] • This mode let you switch from TV to SAT and vice-versa. Procedure: 1. Press ?/1 button to turn on the system. 2. Select TV function. 3. Press [TV/SAT] button and ?/1 button simultaneously. The function will change to SAT. Press the same buttons again to change from SAT to TV. [DVD COLOR SYSTEM] • This mode let you change the color system of the video output from PAL to NTSC or vice-versa. This mode is not available for Latin American and Russian models. Procedure: 1. Press ?/1 button to turn on the system. 2. Select DVD function. 3. Press ?/1 button again to turn off the system. 4. Press X button and ?/1 button simultaneously. The system will turn on automatically. The message “COLOR PAL” or “COLOR NTSC” appears on the fluorescent indicator tube. [REMOTE DISABLE MODE] • This mode let you disable the remote commander reception. When this mode is activated, the system will not response if the button on the remote commander is pressed. The message “RM DISABLE” appears on the fluorescent indicator tube. This mode is essential for conducting test and repairing when no interruption from the other remote commander is expected. This mode is cancelled automatically when the system is turned off. Procedure: 1. Press ?/1 button to turn on the system. 2. Press x button, [DIRECTION] button and [DISC 3] button simultaneously until “SIRCS ON” or “SIRCS OFF” appears on the fluorescent indicator tube. [PROGRESSIVE] • This mode let you change the format of the video output from the COMPONENT OUT jacks among PROGRESSIVE AUTO, PROGRESSIVE VIDEO and INTERLACE. Procedure: 1. Press ?/1 button to turn on the system. 2. Press [DVD] button and [DISPLAY] button simultaneously. “P AUTO” or “P VIDEO” or “INTERLACE” appears on the fluorescent indicator tube. [MTK FIRMWARE DISPLAY] • This mode is used to display the MTK firmware version. Procedure: 1. Press ?/1 button to turn on the system. 2. Press [DVD] button to switch to DVD function. 3. Press ?/1 button again to turn off the system. 4. Press x button and ?/1 button. The system turns on automatically. 5. The version of MTK firmware appears on the TV screen. [DVD SERVICE MODE] • This mode let you make diagnosis and adjustment easily by using the remote commander and the TV. The instructions, diagnostic results, etc. are given on the on-screen display. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 21 HCD-GNZ77D/GNZ88D • TEST DISC LIST Be sure to use the DVD disc that matches the signal standards of your region. • CD YEDS-18 (Part No.: 3-702-101-01) PATD-012 (Part No.: 4-225-203-01) • DVD SL (Single Layer) NTSC : HLX-503 (Part No.: J-6090-069-A) HLX-504 (Part No.: J-6090-088-A) PAL : HLX-506 (Part No.: J-6090-077-A) • DVD DL (Dual Layer) NTSC : HLX-501 (Part No.: J-6090-071-A) HLX-505 (Part No.: J-6090-089-A) PAL : HLX-507 (Part No.: J-6090-078-A) • Procedure to enter to DVD Service Mode: 1. Press ?/1 button to turn on the system. 2. Select DVD function. 3. Press x button and [OPEN/CLOSE] button simultaneously and then turn the [VOLUME] knob clockwise. 4. The message “SERVICE IN” appears on the fluorescent indicator tube and the Top Menu of Remocon Diagnosis Menu appears on the on-screen display on the TV. The model name and revision number is displayed at the bottom of the on-screen display. 3. Select “6. Iop:” by pressing [6] button on the remote commander. 4. Wait until a hexadecimal number appears in the on-screen display as below: Remocon Diagnosis Menu 0. External Chip Check 1. Servo Parameter Check 2. Drive Manual Operation 3. Emergency History 4. Version Information Model Name : GML6DS_ME IF-con : V Syscon : Ver. er. 01.00 (0000) 0.302 5. To execute each function, press its number by using numeric button on the remote commander. 6. To release from this mode, press ?/1 button to turn off the system. • Execute IOP Measurement In order to execute IOP measurement, the following standard procedures must be followed. 1. From the Top Menu of Remocon Diagnosis Menu, select “2. Drive Manual Operation” by pressing the [2] button on the remote commander. The following screen appears on the on- screen display. Drive Manual Operation 1. Servo Control 2. Track/Layer Jump 3. Manual Adjustment 4. Mecha test Mode 5. MIRR time Adjust 0. Return to Top Menu 2. Select “3. Manual Adjustment” by pressing the [3] button on the remote commander. The following screen appears on the on-screen display. Manual Adjust 1. Track Balance Adjust: 2. Track Gain Adjust: 3. Focus Balance Adjust: 4. Focus Gain Adjust: 5. Eg Boost Adjust: 6. Iop: 7. TRV. Level: 8. S curve(FE) Level: 9. RFL(PI) Level: 0. MIRR Time: O o Change Value RETURN Return to previous menu Manual Adjust 1. Track Balance Adjust: 2. Track Gain Adjust: 3. Focus Balance Adjust: 4. Focus Gain Adjust: 5. Eg Boost Adjust: 6. Iop. ED: 7. TRV. Level: 8. S curve(FE) Level: 9. RFL(PI) Level: 0. MIRR Time: O o Change Value RETURN Return to previous menu 5. Convert data from hexadecimal to decimal by using conversion table. 6. Please find the label on the rear of the BU (Base Unit). The default IOP value is written in the label. 7. Subtract between these two values. 8. If the remainder is smaller than 93 (decimal), then it is OK. However if the value is higher than 93, then the BU is defective and need to be change. 9. Press [RETURN] button on the remote commander to return to previous menu. 10. Press [0] button on the remote commander to return to the Top Menu of Remocon Diagnosis Menu. 11. Press ?/1 button to turn off the system. • Check Emergency History To check the emergency history, please follow the following procedure. 1. From the Top Menu of Remocon Diagnosis Menu, select “3. Emergency History” by pressing the [3] button on the remote commander. The following screen appears on the on-screen display. Ver. 1.3 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 22 HCD-GNZ77D/GNZ88D 2. You can check the total time when the laser is turned on during playback of DVD and CD from the above menu. The maximum time, which can be displayed are 999h 59min. 3. You can check the error code of latest 10 emergency history from the above menu. To view the previous or next page of emergency history, press . or > on the remote commander. The error code consists of • Error Code Example of Error code 1. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45 The meaning of error code is as below: 01: Communication error (No reply from syscon) 02: Syscon hung up 03: Power OFF request when syscon hung up 19: Thermal shutdown 24: MoveSledHome error 25: Mechanical move error (5 Changer) 26: Mechanical move stack error 30: DC motor adjustment error 31: DPD offset adjustment error 32: TE balance adjustment error 33: TE sensor adjustment error 34: TE loop gain adjustment error 35: FE loop gain adjustment error 36: Bad jitter after adjustment 40: Focus NG 42: Focus layer jump NG 52: Open kick spindle error 51: Spindle stop error 60: Focus on error 61: Seek fail error 62: Read Q data/ID error 70: Lead in data read fail 71: TOC read time out (CD) 80: Can’t buffering 81: Unknown media type • Parameter of error code This is the detail of error code. Example of Error code 1. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45 • Time of error code This is the laser time when an error occurred. Example of Error code 1. 01 05 04 04 00 92 46 00 00 00 00 00 00 00 23 45 To clear the Laser Hour Press [DISPLAY] button and then press [CLEAR] button. The data for both CD and DVD data are reset. Emg.History Check 1. 01 05 04 04 Laser Hours CD 0h 0min DVD 0h 0min 00 92 46 00 00 00 00 00 00 00 23 45 2. 02 02 01 01 00 A9 4B 00 00 00 00 00 00 00 23 45 Next Next Page Prev Prev Page O Return to Top Menu To clear the Emergency History Press [TOP MENU] button and then press [CLEAR] button. The error code for all emergency history would be reset. Emg.History Check 1. 00 00 00 00 Laser Hours CD 999h 59min DVD 999h 59min 00 00 00 00 00 00 00 00 00 00 00 00 2. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Next Next Page Prev Prev Page O Return to Top Menu Ver. 1.3 Emg.History Check 1. 01 05 04 04 Laser Hours CD 999h 59min DVD 999h 59min 00 92 46 00 00 00 00 00 00 00 23 45 2. 02 02 01 01 00 A9 4B 00 00 00 00 00 00 00 23 45 Next Next Page Prev Prev Page O Return to Top Menu To clear the Initialize Setup Data Press [MENU] button and then press [CLEAR] button on the remote commander. Emg.History Check Initialize setup data... Laser Hours CD 999h 59min DVD 999h 59min Next Next Page Prev Prev Page O Return to Top Menu www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 23 HCD-GNZ77D/GNZ88D To return to the Top Menu of Remocon Diagnosis Menu Press [0] button on the remote commander. • Check Version Information To check the version information, please follow the following procedure. 1. From the Top Menu of Remocon Diagnosis Menu, select “4. Version Information” by pressing the [4] button on the remote commander. The following screen appears on the on-screen display. To return to the Top Menu of Remocon Diagnosis Menu, press [0] on the remote commander. Version information O Return to Top Menu Firm (Main) : Ver. xxxxx Firm (Sub) : xxxxx RISC : xxxxx 8032 : xxxxx Audio DSP : xxxxx Servo DSP : xxxxx SECTION 4 MECHANICAL ADJUSTMENTS Precaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque Measurement 3.06 N • m to 6.96 N • m 31 to 71 g • cm (0.43 – 0.98 oz • inch) 0.19 N • m to 0.58 N • m 2 to 6 g • cm (0.02 – 0.08 oz • inch) 3.06 N • m to 6.96 N • m 31 to 71 g • cm (0.43 – 0.98 oz • inch) 0.19 N • m to 0.58 N • m 2 to 6 g • cm (0.02 – 0.08 oz • inch) 6.96 N • m to 14.02 N • m 71 to 143 g • cm (0.98 – 1.99 oz • inch) 9.80 N • m 100 g or more (3.53 oz or more) 9.80 N • m 100 g or more (3.53 oz or more) Mode Torque meter CQ-102C CQ-102C CQ-102RC CQ-102RC CQ-201B CQ-403A CQ-403R Meter reading FWD FWD back tension REV REV back tension FF/REW FWD tension REV tension Ver. 1.3 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 24 HCD-GNZ77D/GNZ88D SECTION 5 ELECTRICAL ADJUSTMENTS VIDEO SECTION Video Level Check (VIDEO BOARD) Purpose This adjustment is made to satisfy the NTSC standard, and if not adjusted correctly, the brightness will be too large or small. Procedure: 1. Connect oscilloscope to VIDEO output. 2. Load a DVD reference disc playback. 3. Check the video signal level is 1.00±0.07Vp-p. DVD SECTION When the optical pick-up assy is replaced, perform the “Execute IOP Measurement”. Execute IOP Measurement (See page 21) [TEST DISC LIST] Be sure to use the DVD disc that matches the signal standards of your region. • CD YEDS-18 (Part No.: 3-702-101-01) PATD-012 (Part No.: 4-225-203-01) • DVD SL (Single Layer) NTSC : HLX-503 (Part No.: J-6090-069-A) HLX-504 (Part No.: J-6090-088-A) PAL : HLX-506 (Part No.: J-6090-077-A) • DVD DL (Dual Layer) NTSC : HLX-501 (Part No.: J-6090-071-A) HLX-505 (Part No.: J-6090-089-A) PAL : HLX-507 (Part No.: J-6090-078-A) [RFMON Level Check] Connection: Procedure: 1. Connect an oscilloscope to CN105 pin 6 (RFMON) and CN105 pin 3 (GND) on the DMB15 board. 2. Turn the power on. 3. Set the test disc (refer to the TEST DISC LIST) on the tray and press H button to playback. 4. Confirm that oscilloscope waveform is clear and check RFMON signal level is correct or not. Note: A clear RFMON signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform. Checking Location: DMB15 board (Side A) + – CN105 pin 6 (RFMON) CN105 pin 3 (GND) oscilloscope DMB15 board VOLT/DIV: 200 mV TIME/DIV: 500 ns RFMON signal waveform level: 0.58 ± 1.23 Vp-p (DVD) 0.57 ± 1.1 Vp-p (CD) IC102 IC101 IC104 IC201 CN105 CN106 CN105 pin 3 (GND) CN105 pin 6 (RFMON) 1 6 DMB15 BOARD (SIDE A) oscilloscope set J1902 VIDEO OUTPUT 75 Ω 1.00 ± 0.07 Vp-p (WHITE 100%) Ver. 1.3 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 25 HCD-GNZ77D/GNZ88D 0 dB=0.775 V DECK SECTION 1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. 3. After the adjustments, apply suitable locking compound to the parts adjust. 4. The adjustments should be performed with the rated power supply voltage unless otherwise noted. 5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.) 6. The adjustments should be performed for both L-CH and R- CH. 7. Switches and controls should be set as follows unless otherwise specified. • Test Tape Record/Playback Head Azimuth Adjustment Note: Perform this adjustments for both decks Procedure: 1. Mode: Playback Tape Signal Used for P-4-A063 6.3 kHz, –10 dB Azimuth Adjustment DECK A DECK B 3. Mode: Playback 4. After the adjustments, apply suitable locking compound to the pats adjusted. Adjustment Location: Playback Head (Deck A). Record/Playback/Erase Head (Deck B). set MAIN board IC101 Pin 28 (L-CH) Pin 37 (R-CH) MAIN board IC101 Pin 36 (GND) + – level meter test tape P-4-A063 (6.3 kHz, –10 dB) MAIN board IC101 test tape P-4-A063 (6.3 kHz, –10 dB) pin 37 oscilloscope L-CH R-CH V H waveform of oscilloscope in phase 45° 90° 135° 180° good wrong pin 36 pin 28 L R forward forward 2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak. screw position L-CH peak within 1dB output level L-CH peak R-CH peak within 1dB screw position R-CH peak www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 27 27 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-1. BLOCK DIAGRAM — RF/SERVO SECTION — : CD PLAY : DVD PLAY : SACD PLAY • Signal Path DETECTOR 6 2 3 4 5 11 10 19 18 252 253 DVDRFIP DVDA DVDB DVDC DVDD TPI TNI MC MD C D LD01 MD12 LD02 MSW MD11 OSP OSN CD/DVD RF AMP, FOCUS/TRACKING ERROR AMP DVD SYSTEM PROCESSOR DIGITAL SERVO PROCESSOR IC102(1/2) OPTICAL PICK-UP BLOCK 2AXIS DEVICE FOCUS/ TRACKING COIL 23 20 LI M SW 176 22 21 36 48 43 37 1 AUTOMATIC POWER CONTROL (FOR DVD) Q102 (2/2) VOLUME CONTROL Q101, Q103 L AUTOMATIC POWER CONTROL (FOR CD) Q102 (1/2) LASER DIODE (FOR CD) LASER DIODE (FOR DVD) FOCUS COIL DRIVE 42 41 BUFFER 35 3 34 4 TRACKING COIL DRIVE 32 38 42 37 41 30 47 FOCUS/TRACKING COIL DRIVER, SPINDLE, SLED MOTOR DRIVER IC201 27 28 SPINDLE MOTOR DRIVE M SPINDLE 46 47 FMO FOO DMO TRO V REFO SPFG 40 IOPMON FOO RF A B C D F E CD LD PD LIMIT VR650 VR780 MSW DVD LD FCS+ FCS– TRK+ VCC TRK– SP+ SP– SL+ SL– D C B A V1P4 V1P4 9 NB B 8 NA A 30 29 SLED MOTOR DRIVE MM 50 BUFFER 19 20 22 21 40 45 SYSTEM CONTROL IC401(1/4) 99 IFCK MTK_CLK 33 100 XIFCS MTK_XIFCK 27 110 PRST MTK_RESET 26 98 IFSDO MTK_SOD 32 101 IFSDI 105 IFBSY KRMOD/HSYNC MTK BUSY 28 KRMOD 24 MTK_SIO 31 TRO FMO FOO DMO TRO 10 13 FMO DMO 211 MUTE123 210 MUTE 170 TSDM 207 MIC STATUS 25 MIC/VSYNC 205 SLED SECTION 6 DIAGRAMS w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 28 28 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-2. BLOCK DIAGRAM — VIDEO SECTION — DVD SYSTEM PROCESSOR IC102(2/2) 217 ASDAT0 ASDAT1 ASDAT2 ASDAT4 225 SDPIF EEPROM IC103 6 5 SCL SDA CE WE OE FLASH ROM IC101 125-123, 121, 120, 118, 117, 115, 135, 133-128, 126 146, 147, 149-151, 158-160, 162, 164-166 22-26, 29-35 HIGHA0-7 IOA0-7, IOA18-IOA21 A16, A17 AD0 – AD7 A1-A21 DATA & ADDRESS BUS DATA & ADDRESS BUS 81-84,86-88,91 53-61, 67-72, 74-76, 78, 89, 92, 93 HD0 – HD7 A0 – A21 HD0 – HD7 A0 26 45 CE WE 28 OE 11 A0 – A19 DQ15/A-1 77 IOCS IOWA 79 IOUE 66 DQ0 – DQ7 RCLK CE WE OE SDRAM IC104 38 DRCLK RD0 – RD15 RA0 – RA11 RA0 – RA11 RD0 – RD15 142 RCS 19 RCS 138 RWE 16 RWE 140 RAS 18 RAS 139 CAS 17 CAS DQM0 15 DQM0 DQM1 39 DQM1 CKE 37 DRCKE 102 SCL 103 SDA 143 BA0 20 BS0 BA1 21 BS1 29,31,33,35,38,40,42,44 25-16, 10 -1, 48 145 156 113 137 157 2,4,5,7,8,10,11,13,42,44,45,47,48,50,51,53 218 46 LOUT2+ SURROUND L IC3731 GNZ77D D/A CONVERTER IC301 IC3751 (1/2) IC3751 (2/2) IC3771 IC3711 45 LOUT2– 219 222 203 YUV6 49 WIDE 48 DSEL 196 YUV2 194 YUV1 200 YUV4 202 YUV5 198 YUV3 220 XRST 215 ACLK 214 ABCK 213 ALRCK 14 SDTI1 V C Y YG CR/B CB/R WIDE DSEL (SL) 15 SDTI2 16 SDTI3 13 SDTI4 8 PDN 10 MCLK 9 BICK 17 LRCK 19 SCL 20 SDA 42 CENTER 41 40 SUBWOOFER 39 38 DOWNMIX L 37 2 FRONT L 1 DIGITAL OPTICAL TRANSMITTER IC508 DVD DIGITAL OUT LOUT3+ LOUT3– (FC) ROUT3+ ROUT3– (SW) LOUT4+ LOUT4– (DMIXL) LOUT1+ LOUT1– (FL) GNZ77D B MAIN SECTION 208 SMSCK 206 VOICE VOICE SCORE A MAIN SECTION C MAIN SECTION XTALI XTALO 229 228 X101 27MHz • Signal Path : VIDEO : COMPONENT VIDEO : AUDIO : DIGITAL (Page 29) (Page 29) (Page 29) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 29 29 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-3. BLOCK DIAGRAM — MAIN SECTION — 57 FRONT CENTER SUBWOOFER SURROUND L FRONT L DOWNMIX L DVD/CD Z0 TU–LCH LINE VIDEO MIC 4 3 29 5 VRSW Z1 3 X0 23 12 TONE L 1 SW CHANNEL SELECT 28 FRONT L 7 MUSIC L+R 53 L+R LIGHTING 26 F/B 37 FRONT R GNZ88D R–CH R–CH 4 Z 14 X 5 VOL1 6 VOL2 7 VO 3 29 POOUT 15 MIC1P 16 MIC2P 21 MCO 42 TONE R X1 13 Z–Z1 9 2 SURR CHANNEL SELECT X–X1 SL OUT SW OUT CENTER SW OUT FRONT L ADC RESET DBFB FEED BACK 11 88 VACS IN 66 IO EXP DATA OUT 68 IO EXP RST 69 IO EXP CLK 70 IO EXP LAT 26 D1 V C Y YG WIDE CB/R DSEL INIT NSP MUTE SOFT MUTE 4 LATCH 3 CLK 2 RESET DATA CLK RST DATA LAT LAT CLK RST 22 VIDEO OUT SW 21 VIDEO MUTE 24 FAN CNT 22 ADC RESET 8 DO 6 DI 7 CL 9 CE 1 TUNED R–CH R–CH FM 75Ω COAXIAL DIN DOUT CLK CE TUNED ST A+9V 5 LCH 3 RCH R–CH 4 +9V 5 2 59 PB A 75 PB B 76 REC 17 CLK 34 DATA 35 CLK 84 DIN 37 DOUT 39 CLK 38 CE ST 36 TUNED 40 DATA 83 DVD A MUTE 34 MIC DETECT 23 B SHUT 90 A SHUT 89 A HALF 63 B HALF 91 CY–IN 10 S1 25 C–IN CVBS IN 2 PB/CB PR/CR Y 4 3 2 MUTE1 3 MUTE2 13 Y–IN 6 Y OUT CYOUT CB OUT CR OUT 21 S–DC OUT 27 CVBSOUT 23 C OUT 26 20 18 16 CB–IN 12 I/P 9 CR/B CR–IN 14 REC MUTE 7 REC BIAS 20 TC REALY 21 CAMP CNT 18 B TRIG 19 A TRIG 17 SM INIT 12 SM NSP MUTING 9 SM SOFT MUTING 10 1 SELECT SWITCH Q261 MUTE CONTROL Q301,302 MUTE Q175 MUTE CONTROL Q110,111 MUTE Q166 MUTE Q285 MIC2 LEVLE RV1401 ECHO AMP IC1400 ECHO LEVEL RV1401 MIC AMP IC1401 MIC1 LEVLE DVD/CD MUTE CONTROL Q307,308 RV1401 REC/PB AMP, SOUND CONTROL IC101 SIGNAL SELECT IC205 MUTE Q235 MUTE Q236 MUTE Q238 MUTE Q237 SELECT SWITCH Q260 DBFB FEED BACK Q101 FAN DETECT Q580,582 FAN CONTROL Q584 FAN DRIVE Q585 AM J501 J501 TU901 ANTENNA TV/SAT IN L R J1402 J1402 J1400 AUDIO MIC 1 J1450 MIC 2 VIDEO VIDEO INPUT L R D AUDIO SECTION G AUDIO SECTION B VIDEO SECTION C VIDEO SECTION F AUDIO SECTION SCORE VOICE A VIDEO SECTION E AUDIO SECTION R-CH PB HEAD HP901 BIAS OSC Q112 T101 R-CH ERASE HEAD REC/PB HEAD R-CH BIAS+9V MUTE CONTROL Q107–109 HRPE901 (DECK B) (DECK A) TAPE MECHANISM DECK BLOCK B SHUT A SHUT A HALF B HALF REC(REV) CAP M+ REC(FWD) B TRGM+ A TRGM+ B TRG CONTROL Q118,119 CAP CONTROL Q120,121 A TRG CONTROL Q122,123 UNREG+12V FAN901 FAN DET 75 OHM DRIVER IC1801 C J1902 (2/2) S VIDEO OUT Y J1902 (1/2) VIDEO SELECTOR IC1805 VIDEO OUT D–LIGHT SYNC OUT J506 SUB WOOFER OUT J503 J1900 COMPONENT OUT Q154, 155 Q113,114 SIGNAL IN/OUT CONTROL IC403 SYSTEM CONTROL IC401 (3/4) MUSIC L+R AC/DC CONVERTER IC2000 (2/2) MIC AC/DC CONVERTER IC2000 (1/2) DETECT COMPARATOR IC2001 LIMIT VOICE COMPARATOR IC2002 • Signal Path : TUNER : AUDIO : PB (DECK A) : PB (DECK B) : REC (DECK B) : VIDEO : COMPONENT VIDEO • R-CH is omitted due to same as L-CH. 7 SOFT MUTE CONTROL Q305,306,311 MUTE Q263,264 JW261 GNZ77D (Page 28) (Page 28) (Page 30) (Page 30) (Page 28) (Page 30) (Page 30) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 30 30 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-4. BLOCK DIAGRAM — AUDIO SECTION — 41 4 2 7 9 43 3 SERIAL CLOCK BUFFER IC3 SYSTEM CONTROL IC401(2/4) E–3 OPEN SWITCH SM LATCH3 79 SM LATCH2 76 SM LATCH1 77 SM CLK 78 SM DATA 65 SM RESET 72 SM SD 86 HP MUTE 85 HP DET 44 E–2 45 E–1 42 TABLE SENSE 48 LM–F DBFB FEED BACK FRONT L R-CH ADC RESET SL OUT R-CH IC701 M751 (LOADING) M741 (TABLE) LOADING MOTOR DRIVE 4 2 IC712 TABLE MOTOR DRIVE M M Q731 IC731 TABLE ADDRESS SENSOR 11 A/D CONVERTER IC11 A/D CONVERTER IC12 1 2 7 1 15 12 10 12 11 D/A CONVERTER IC500 SUB WOOFER AMP IC812 CLOSE OPEN RE701 G MAIN SECTION D MAIN SECTION F MAIN SECTION E MAIN SECTION S751 OPEN/CLOSE DETECT DISC TRAY ADDRESS DETECT L IN R IN 31 DATA R–CH OUTL1 OUTL2 OUTR1 OUTR2 XFSOIN XFSOOUT HPOUTL1 HPOUTL2 HPOUTR1 HPOUTR2 NSPMUTE SOFTMUTE SCDT SCSHIFT SCLATCH INIT FSOCKO 29 LRCK 30 BCK 36 XFSIIN 2 R IN SCKI 15 SCKI PDWN 7 L IN D OUT LRCK BCK D OUT 10 LRCK 11 BCK SW OUT CENTER 1 12 2 15 7 49 LM–R 46 TM–F 47 TM–R 7 9 10 11 9 6 R–CH 4 18 D/A CONVERTER IC700 36 XFSIIN 31 DATA 30 BCK 29 LRCK NSPMUTE SOFTMUTE SCDT SCSHIFT 19 21 22 23 SCLATCH INIT FSOI XFSOIN 27 38 48 OUTL1 11 OUTL2 9 HPOUTR1 41 HPOUTR2 39 11 D/A CONVERTER IC600 36 XFSIIN R-CH R-CH 31 DATA 30 BCK 29 LRCK 21 SCDT 14 XFSOOUT 19 SOFTMUTE 18 NSPMUTE 37 FSOCKO 22 SCSHIFT 27 INIT 48 XFSOIN GNZ88D GNZ88D GNZ88D SW OUT INIT NSP MUTE SOFT MUTE 38 FSOI 23 SCLATCH OUTL1 OUTL2 OUTR1 OUTR2 9 AMP (SURROUND) IC630 AMP (CENTER) IC730 33 4 PWM A UNREG+8V 6 PWM B OUT A OUT B 30 OUT C 25 OUT D 22 /SD 3 RESET AB 5 RESET CD 15 /SD 4 /RESET 5 6 4 R-CH R-CH R-CH R-CH R-CH FAN DET R-CH R-CH AMP (FRONT LCH) IC530 14 PWM B 6 PWM A DC DETECT Q850,851 OUT A 4 /SD 5 /RESET R–CH 41 R–CH 39 45 43 14 48 18 19 21 22 23 27 37 FSOI 38 28 l 30 OUT B 25 l 27 OUT A 28 l 30 OUT B 25 l 27 HP AMP IC880 IC803 6 PWM A 14 PWM B GNZ77D DC DETECT Q860,861 DC DETECT Q870,871 FRONT SPEAKER L R TM1500 (1/3) SURROUND SPEAKER PHONES J1401 L R CENTER SPEAKER MUTE Q1400,1401 DC DETECT Q840 SERIAL CLOCK BUFFER IC800 MUTE CONTROL Q486 D486 TM1500 (2/3) TM1500 (3/3) X1 12.288MHz X800 49MHz PDWN A/D CONVERTER IC13 R IN SCKI L IN D OUT LRCK BCK PDWN • Signal path : AUDIO : DIGITAL (Page 29) (Page 29) (Page 29) (Page 29) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 31 31 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-5. BLOCK DIAGRAM — FUNCTION/POWER SECTION — 57 58 FL DRIVER CLK FL DRIVER DATA FL DRIVER CS FL DRIVER RESET DR5 I DR11 DR12 I DR14 DR16 I DR35 60 59 SI SCK CSB RSTB 49 48 51 52 SYSTEM CONTROL IC401 (4/4) D1304 (STANDBY) D1307–1312 SIRCS 4 VIN POWER CONTROL IC1100 C VCC FB Z/C FUNCTION KEY S1309–1316 REMOTE CONTROL SIGNAL RECEIVER IC1301 97 S1317,1319,1324–1327 95 S1306,1318,1320–1323,1328,1331 94 56 12 STBY LED 53 LED CTRL RESET 20 AC CUT AD KEY3 AD KEY2 AD KEY1 XC IN XC OUT X IN X OUT 51 50 LED ILLUMINATION 1 LED ILLUMINATION 2 LED ILLUMINATION 3 52 LED ILLUMINATION CONTROL Q1305–1307 X401 32.768kHz X402 5MHz 11 10 13 MTK POWER 35 MAIN ON/OFF 100 15 LED ON/OFF CONTROL Q1308,1310 FL DRIVE IC1300 FUNCTION KEY FUNCTION KEY FUNCTION KEY S1300 73 S1301 74 S1305 54 VOL A POWER KEY DISPLAY KEY FUNCTION KEY ROTARY ENCODER 55 VOL B LED POWER CONTROL Q1303,1304 VP F1 F2 DVD SW+9V REG IC1802 DVD SW+3.3V REG IC1803 DVD SW+5V REG IC1804 POWER CONTROL Q132,133 RESET SWITCH Q213 RESET IC402 DVD SW+9V AUDIO+9V REG IC552 M+9V/LED+9V REG IC551 +12V REG IC1102 RECT D1114 ST A+9V M+9V UNREG+12V +31V 120V SW1100 EQ Q1300 AUDIO A+9V D+3.3V D+4V DVD+3.3V RF+1.8V RF+3.3V UNREG+8V A+5V A+8.4V A+5V EVER+4V D215 D216 AC IN D1300 D1102 D1101 D1119 D1110 D1112 D1120 T1100 MAIN TRANSFORMER T1300 DC/DC CONVERTER TRANSFORMER D1302 D1301 D594 A+5V REG Q131 D1303 BIAS +9V +3.3V EVER+4V FL+4V FL+3.3V D+3.3V D393 D396 D395 D1314 D394 D506 F1110 FEED BACK PC1100 STANDBY CONTROL PC1101 STANDBY CONTROL PC1102 STANDBY CONTROL Q1102 STANDBY CONTROL Q1200 FEED BACK PC1200 POWER DETECT IC1201 220 l 240V VOLTAGE SELECTER +4V SWITCH Q1203,1204 +8V SWITCH Q1205,1206 FILTER LF1101 A+5V REG IC1 D+4V REG IC562 7 I 13 • 15 I 17 • 19 I 38 DR0 I DR4 • DR15 2 I 6 • 18 FL1300 VACUUM FLUORESCENT DISPLAYS D+3.3V +1.8V RECT D1212 POWER DETECT IC1101 POWER CONTROL Q1100,1101 RF+1.8V REG IC106 +3.3V +3.3V REG IC105 DVD SW+5V RF+3.3V REG IC107 RECT D1213 RECT D1100 MTK POWER CONTROL Q1970,1971 FL DRIVE CONTROL Q1311–1316 6 7 4 3 1 D POWER CONTROL IC1200 VCC FB Z/C 5 4 2 1 GNZ88D:EXCEPT TH T1200 SUB TRANSFORMER D+3.3V REG IC2 +1.8V REG IC810 D1211 D1201 D1208 D1207 • Abbreviation E2 : 120 V AC area in E model E3 : 240 V AC area in E model E12 : 220–240 V AC area in E model E13 : 220–230 V AC area in E model E15 : Iran model EA : Saudi arabia model PH : Philippine model SP : Singapore model TH : Thai model GNZ88D GNZ77D: POWER UNIT GNZ88D w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 32 32 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D • Note For Printed Wiring Boards And Schematic Diagrams Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • : Pattern from the side which enables seeing. (The other layer’s patterns are not indicated.) Caution: Pattern face side: Parts on the pattern face side seen from (Conductor Side) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Component Side) the parts face are indicated. • Indication of transistor. • A : B+ Line. • B : B– Line. • Voltage and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ∗ : Impossible to measure • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal produc- tion tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal produc- tion tolerances. • Circled numbers refer to waveforms. • Signal path. F : AUDIO f : TUNER L : VIDEO (COMPONENT) g : VIDEO (COMPOSITE) E : TAPE PLAY (DECK A) d : TAPE PLAY (DECK B) G : TAPE REC (DECK B) J : DVD (AUDIO) c : DVD (RF) I : DVD (DIGITAL) • Abbreviation E2 : 120 V AC area in E model E3 : 240 V AC area in E model E12 : 220-240 V AC area in E model E13 : 220-230 V AC area in E model E15 : Iran model EA : Saudi arabia model PH : Philippine model SP : Singapore model TH : Thai model Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 °C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. 6-6. CIRCUIT BOARDS LOCATION C B These are omitted. E Q B These are omitted. C E Q B These are omitted. C E Q Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • 2 : nonflammable resistor. • C : panel designation. MIC board PANEL board KARAOKE board VOLUME board IR board DRIVER board ADC board S-MASTER board SPEAKER board MAIN board SW board DMB15 board MOTOR (LD) board MOTOR (TB) board SENSOR board POWER UNIT VIDEO board MIC board PANEL board KARAOKE board VOLUME board IR board DRIVER board ADC board S-MASTER board SPEAKER board MAIN board SW board DMB15 board MOTOR (LD) board MOTOR (TB) board SENSOR board POWER board VIDEO board HCD-GNZ77D HCD-GNZ88D w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 33 33 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D • Waveforms — DMB15 BOARD — — S-MASTER BOARD — — MAIN BOARD — — ADC BOARD — 1 IC102 6 (DVDRFIP) 0.5 Vp-p 200 mV/DIV, 100 nsec/DIV 500 mV/DIV, 20 µsec/DIV 2 IC102 ea (FED) 100 mV/DIV, 1 msec/DIV 6 IC102 > . MASTER VOLUME GROOVE 1 2 3 S1331 NO1402 1 11 PANEL BOARD CN1452 PL1300 JW1389 JW1396 JW1397 JW1398 JW1399 JW1427 S1305 JW1431 D1307-1312 (RING ILLUMINATION) (CHASSIS) (Page 56) Ref. No. Location D1307 H-7 D1308 F-8 D1309 D-7 D1310 H-5 D1311 F-4 D1312 D-5 • Semiconductor Location w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 58 58 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-29. SCHEMATIC DIAGRAM — PANEL SECTION — L1300 C1301 R1300 D1303 D1301 D1300 D1302 R1302 R1304 R1303 R1305 R1301 TP1302 TP1303 TP1300 R1306 C1309 TP1304 TP1305 TP1306 TP1307 TP1308 TP1309 TP1310 TP1311 TP1312 TP1313 TP1314 TP1315 TP1316 R1308 D1306 CN1403 CN1453 D1310 D1309 D1308 D1307 TP1317 TP1318 Q1303 R1346 R1345 R1348 R1347 Q1310 Q1308 Q1307 Q1306 Q1305 Q1311 R1356 Q1312 Q1313 Q1314 Q1315 R1357 R1358 R1359 R1360 R1361 D1314 IC1301 C1302 C1306 C1307 C1357 C1308 S1301 S1300 R1314 R1335 D1311 C1320 C1319 C1318 C1317 C1316 D1312 C1321 R1328 R1316 R1317 R1318 R1319 R1320 R1321 R1322 R1323 R1324 R1325 R1334 R1329 R1332 R1331 R1330 R1336 R1326 R1327 R1333 R1337 C1322 C1323 C1324 C1325 C1326 C1327 C1328 C1329 C1330 C1331 R1365 R1364 R1362 R1363 R1366 R1367 R1368 R1369 R1370 R1371 R1372 R1373 CN1402 C1334 R1374 R1375 R1376 R1377 R1378 R1379 R1351 R1352 R1353 R1355 NO1402 CN1452 D1305 R1307 C1312 C1313 C1310 C1311 C1314 C1315 S1316 S1315 S1314 S1313 S1312 S1311 S1310 S1309 S1308 S1307 S1320 S1321 S1322 S1323 S1317 S1325 S1326 S1327 S1324 Q1316 S1306 S1328 S1318 S1331 S1319 S1305 PL1300 Q1300 T1300 C1300 C1304 C1305 FL1300 JR1305 IC1300 JW1322 JW1300 D1304 JW1301 Q1304 JR1300 JR1301 JR1302 (Page 44) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 59 59 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-30. PRINTED WIRING BOARD — MIC SECTION — • Refer to page 32 for Circuit Boards Location. : Uses unleaded solder. 1 A B C D E F 2 3 4 5 6 7 8 9 10 11 12 13 J1402 AUDIO R L VIDEO VIDEO INPUT J1401 PHONES RV1402 ECHO LEVEL RV1401 MIC 2 LEVEL RV1400 MIC 1 LEVEL J1450 MIC 2 Q (CHASSIS) (CHASSIS) (CHASSIS) 1-868-831- S-MASTER BOARD CN503 VIDEO BOARD CN1967 H T MAIN BOARD CN205 11 (11) 2 5 4 6 1 1 3 1 11 7 3 J1400 MIC 1 2 5 4 6 1 7 3 IC1400 C1468 R1441 JR1402 R1461 R1426 C1411 C1461 R1410 R1460 R1409 R1459 R1411 C1418 R1427 R1476 JR1417 IC1401 R1425 R1438 C1413 R1412 R1413 C1419 R1414 R1415 R1402 R1403 R1404 R1405 R1406 C1412 C1400 C1433 R1401 C1403 C1405 R1439 R1440 R1431 JR1427 R1437 D1400 C1415 R1419 R1469 JR1400 R1422 C1424 C1422 C1401 R1417 R1416 R1418 R1407 R1457 R1477 R1432 C1436 C1437 JR1433 R1492 R1493 Q1450 Q1400 Q1401 R1442 R1435 R1443 R1436 R1433 R1434 C2 JR1403 JR1401 R1482 C1486 JR1483 C1487 ECB ECB ECB ECB R1485 R1486 Q1451 R1483 R1484 C1427 R1424 C1479 JW1402 JW1404 JW1405 JW1407 JW1408 JW1410 JW1411 JW1414 JW1415 JW1416 JW1418 JW1419 JW1420 JW1421 JW1413 JW1409 PL1400 PL1402 JW1426 JW1437 C1460 C1410 C1459 C1458 C1408 C1409 C1407 C1406 C1429 C1430 C1435 C1416 J1402 RV1401 RV1402 RV1400 J1450 EPT1403 J1401 2 3 2 1 30 16 1 15 1 3 2 1 3 2 1 3 2 6 1 7 5 4 J1400 C1434 C1404 EPT1400 C1426 C1476 NO1400 EPT1402 JW1423 JW1422 JW1424 NO1404 JW1438 JW1439 JW1440 C1457 NO1401 JW1417 JW1429 JW1400 JW1425 JW1432 JW1412 JW1401 JW1403 (Page 49) (Page 43) (Page 63) Ref. No. Location D1400 D-7 IC1400 C-9 IC1401 C-7 Q1400 C-3 Q1401 B-3 Q1450 C-4 Q1451 B-4 • Semiconductor Location w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 60 60 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-31. SCHEMATIC DIAGRAM — MIC SECTION — TP1400 TP1401 TP1402 TP1403 TP1404 TP1405 R1401 RV1400 RV1401 RV1402 R1402 R1403 R1404 R1405 R1406 TP1406 TP1407 TP1408 TP1409 R1410 R1411 R1461 R1460 R1412 R1413 IC1400 J1402 NO1400 R1419 R1469 TP1411 TP1412 R1422 J1401 R1426 R1427 R1425 R1477 R1476 C1435 C1433 R1437 R1424 R1431 R1438 R1439 R1440 R1441 JR1417 NO1404 R1416 R1417 R1418 R1407 C1436 C1437 C1486 C1487 JR1400 JR1401 C1416 JR1427 Q1450 Q1400 R1432 R1434 R1436 R1482 R1484 R1486 R1492 R1493 R1442 R1443 R1433 R1435 R1485 R1483 C1457 C1412 C1415 C1401 C1422 C1418 C1468 C1427 C1413 C1403 C1405 C1400 C1419 IC1401(1/2) IC1401(2/2) R1457 R1414 R1415 C1407 C1406 C1461 C1411 C1404 NO1401 JR1402 EPT1400 EPT1402 EPT1403 JR1433 JR1483 Q1401 Q1451 C1424 R1459 R1409 J1450 J1400 C1410 C1460 C1409 C1408 C1459 C1458 D1400 C1429 JW1400 C1479 C1434 C1430 C1426 C1476 JW1426 (Page 64) (Page 45) (Page 52) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 61 61 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-32. PRINTED WIRING BOARD — KARAOKE SECTION — • Refer to page 32 for Circuit Boards Location. : Uses unleaded solder. 1 A B C D E F G H I J 2 3 4 5 6 7 8 9 10 11 12 13 IC2000 IC2001 IC2002 R2002 R2000 R2001 R2005 R2004 R2037 R2007 R2010 R2009 R2012 C2008 R2014 D2000 D2001 R2008 R2011 C2007 R2015 D2002 D2003 R2016 C2016 R2017 R2019 R2022 R2021 D2006 D2008 R2020 R2025 R2024 C2013 R2026 R2031 R2028 R2029 R2030 R2036 R2034 R2032 R2035 C2015 D2007 C2001 1 6 C2000 C2002 C2004 C2006 C2009 C2005 C2010 C2011 JW2008 JW2001 JW2002 JW2003 JW2004 JW2005 JW2006 JW2007 JW2009 JW2010 JW2011 JW2012 CN2000 1-869-677- (11) 11 J MAIN BOARD CN403 (Page 43) Ref. No. Location D2000 E-6 D2001 F-6 D2002 C-6 D2003 C-6 D2006 F-4 D2007 F-4 D2008 F-4 IC2000 E-7 IC2001 H-3 IC2002 H-7 • Semiconductor Location w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 62 62 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-33. SCHEMATIC DIAGRAM — KARAOKE SECTION — C2004 R2012 R2007 C2005 R2008 C2010 R2015 C2011 R2016 C2006 R2020 R2026 R2019 R2011 R2017 R2025 R2029 R2035 R2034 R2009 C2009 C2002 R2000 R2001 R2002 R2031 C2001 R2028 C2000 R2021 R2037 R2004 R2014 R2032 IC2002(2/2) IC2002(1/2) IC2000(2/2) IC2001(1/2) IC2001(2/2) IC2000(1/2) CN2000 C2016 R2005 C2013 C2015 C2007 C2008 R2010 R2022 R2024 R2036 R2030 D2008 D2007 D2006 D2003 D2002 D2001 D2000 (Page 45) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 63 63 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-34. PRINTED WIRING BOARD — VIDEO SECTION — • Refer to page 32 for Circuit Boards Location. : Uses unleaded solder. 1 A B C D E F G H 2 3 4 5 6 7 8 9 10 11 12 13 K T MIC BOARD NO1400 MAIN BOARD NO361 C DMB15 BOARD CN401 1-869-012- 11 (11) S VIDEO OUT VIDEO OUT -1 -2 -3 J1900 J1902 -2 -1 COMPONENT OUT PR/CR PB/CB Y -3 -2 -1 -1 B DMB15 BOARD CN301 Y C G G (CHASSIS) R1947 IC1805 Q1970 Q1971 FB1974 FB1980 JR1910 R1889 R1937 IC1801 JR1913 C1857 C1875 C1869 C1870 R1941 R1934 C1888 R1932 R1940 R1939 R1930 R1938 R1931 R1888 FB1976 C1876 C1863 R1935 C1871 R1933 C1892 FB1972 FB1979 FB1973 FB1971 FB1975 D1888 C1862 R1942 C1868 C1874 C1873 R1936 R1929 C1850 JW1931 JW1930 JW1929 CN1880 NO1960 JW2002 JW2003 JW2004 JW2009 JW2010 JW2011 JW2012 JW2013 JW2014 JW2015 JW2016 1 5 1 8 JW2017 JW2018 JW2020 JW2005 J1900 IC1802 IC1803 IC1804 C1885 C1883 C1861 C1886 C1884 C1882 CN1966 CN1967 C1893 C1864 C1865 C1866 C1867 C1860 C1859 C1858 C1887 C1856 C1855 C1854 C1853 C1891 C1889 JW2021 JW2022 1 1 4 4 1 4 L1888 L1950 J1902 JW2006 JW1928 JW2007 JW2008 JW2001 JW2000 JW1915 EPT1970 JW1885 JW1886 JW1887 JW2023 JW2019 B C E B C E JW2024 14 15 1 28 (Page 59) (Page 36) (Page 36) (Page 43) Ref. No. Location D1888 D-9 IC1801 F-8 IC1802 C-5 IC1803 C-4 IC1804 C-3 IC1805 D-9 Q1970 D-4 Q1971 E-3 • Semiconductor Location w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 64 64 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-35. SCHEMATIC DIAGRAM — VIDEO SECTION — C1868 C1853 R1938 R1937 C1873 C1874 C1869 C1870 R1940 JR1910 L1950 C1855 R1936 R1930 R1947 R1941 R1942 CN1880 D1888 JR1913 JR1914 CN1967 C1862 FB1971 FB1975 J1900 FB1972 FB1973 FB1974 C1871 TP1995 FB1976 TP1996 C1863 Q1971 Q1970 FB1979 FB1980 IC1805 TP1800 C1892 R1889 R1888 R1929 C1854 C1856 C1857 C1858 C1859 C1860 C1861 CN1966 C1867 C1866 C1865 C1864 R1931 R1932 R1933 R1934 C1891 C1893 C1889 J1902 G1990 C1882 C1883 C1884 C1885 C1887 C1886 G1992 NO1960 EPT1970 JW2001 JW1929 IC1804 IC1803 IC1802 L1888 JW1885 JW1886 JW1887 JW1931 C1875 C1876 R1939 C1888 R1935 C1850 IC1801 (Page 38) (Page 60) (Page 47) (Page 38) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 65 65 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-36. PRINTED WIRING BOARD — SPEAKER SECTION — • Refer to page 32 for Circuit Boards Location. : Uses unleaded solder. 1 A B C D E F 2 3 4 5 6 7 8 9 10 11 12 13 14 P O S-MASTER BOARD NO780 S-MASTER BOARD NO680 S-MASTER BOARD NO580 R (CHASSIS) (CHASSIS) 1-869-011- (11) 11 GNZ88D FRONT SPEAKER SURROUND SPEAKER CENTER SPEAKER L -5 -4 -3 -2 -1 GNZ88D GNZ88D R L R TM1500 TM1500 JW1720 JW1610 EP1501 EP1500 JW1520 JW1630 JW1500 JW1510 JW1620 JW1600 JW1730 CN1700 1 2 CN1500 JW1530 PL1500 PL1700 CN1601 C1732 C1722 C1602 C1612 C1622 C1632 C1502 C1512 C1522 C1532 (Page 49) (Page 49) (Page 49) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 66 66 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-37. SCHEMATIC DIAGRAM — SPEAKER SECTION — (Page 51) CN1601 CN1500 EP1501 EP1500 CN1700 TM1500 JW1720 JW1730 JW1600 JW1610 JW1620 JW1630 JW1500 JW1510 JW1520 JW1530 C1522 C1722 C1723 C1602 C1612 C1622 C1632 C1502 C1512 C1532 (Page 51) (Page 53) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 67 67 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D 6-38. PRINTED WIRING BOARD — POWER SECTION (HCD-GNZ88D) — • Refer to page 32 for Circuit Boards Location. : Uses unleaded solder. 1 A B C D E F G H I 2 3 4 5 6 7 8 9 10 11 12 13 14 S AC IN S-MASTER BOARD CN502 L MAIN BOARD CN590 11 (CHASSIS) (12) (CHASSIS) (CHASSIS) (CHASSIS) (CHASSIS) (CHASSIS) (CHASSIS) (CHASSIS) (CHASSIS) 220–240V 120V EXCEPT TH MODEL JR1106 JR1107 D1122 C1148 R1228 R1227 R1226 R1225 C1207 C1206 R1209 R1210 JR1108 Q1102 R1114 R1111 Q1101 R1142 Q1205 R1112 R1202 R1110 C1120 C1140 R1116 Q1100 C1203 C1122 C1130 C1131 R1121 R1122 R1117 R1126 R1127 R1140 D1120 R1145 R1144 R1230 R1224 R1229 R1232 R1233 R1234 R1123 R1124 R1130 R1146 Q1200 D1111 JR1101 R1217 R1135 R1220 R1136 C1214 R1221 R1218 R1216 R1215 R1131 R1132 R1133 R1139 R1219 1 3 1 2 4 1 5 3 2 4 3 1 2 4 3 R1223 D1208 Q1203 R1207 R1208 R1212 R1211 C1139 C1219 C1217 C1218 C1129 Q1204 C1119 C1208 R1141 D1115 R1128 R1129 R1115 JR1105 JR1103 Q1206 C1116 F1100 JW1103 JW1100 R1119 JW1200 C1141 JW1105 JW1107 JW1102 JW1109 JW1110 JW1111 JW1112 JW1120 JW1121 JW1122 JW1123 JW1124 JW1125 JW1126 JW1127 JW1128 JW1130 JW1133 JW1134 JW1135 JW1136 JW1137 JW1138 JW1139 JW1140 JW1141 JW1142 JW1143 JW1146 JW1147 JW1148 JW1150 JW1151 JW1152 JW1154 JW1157 JW1158 JW1159 JW1160 JW1161 JW1163 JW1164 JW1165 JW1166 JW1167 JW1168 JW1131 JW1114 JW1162 JW1132 JW1173 JW1145 JW1149 JW1169 JW1170 JW1176 JW1179 JW1156 JW1184 JW1144 C1132 JW1185 C1102 C1103 C1104 JW1201 JW1155 JW1129 C1128 CLP1100 CLP1101 D1103 C1149 D1108 C1101 D1200 C1210 D1102 L1201 EP1200 EP1106 EP1104 C1127 R1201 D1203 IC1200 PC1102 PC1200 D1202 C1212 1-868-958- C1147 C1216 D1205 D1110 D1109 D1107 C1202 D1119 D1112 D1106 C1118 PC1100 PC1101 R1109 R1105 R1106 C1113 C1209 D1101 L1200 IC1102 1 3 2 4 5 R1137 R1138 C1136 C1138 C1221 C1134 CN1200 R1113 TH1100 C1109 EP1103 C1115 L1102 D1100 D1114 EP1105 D1118 CNP1100 FH1101 FH1100 LF1101 VD1100 D1213 C1222 R1120 D1116 C1213 D1212 IC1201 R1103 C1200 R1200 R1214 D1211 C1121 D1117 C1107 D1207 D1204 C1110 C1112 IC1101 D1206 SW1100 VOLTAGE SELECTER C1117 CN1101 1 7 EP1100 EP1101 EP1102 D1214 L1100 D1215 R1203 IC1100 1 3 4 7 6 5 2 T1100 MAIN TRANSFORMER CONVERTER TRANSFORMER T1200 SUB TRANSFORMER CONVERTER TRANSFORMER 1 1 2 4 3 1 2 4 3 3 C1220 1 2 JW1177 JW1178 EXCEPT TH MODEL TH MODEL Ref. No. Location D1100 D-3 D1101 D-4 D1102 C-3 D1103 B-5 D1106 C-6 D1107 B-7 D1108 C-8 D1109 B-8 D1110 B-8 D1111 B-8 D1112 B-7 D1114 B-11 D1115 G-10 D1116 B-12 D1117 D-12 D1118 G-5 D1119 E-7 D1120 B-9 D1122 B-8 D1200 F-7 D1202 H-6 D1203 G-5 D1204 F-6 D1205 F-6 D1206 F-6 D1207 F-5 D1208 F-6 D1211 G-6 D1212 H-8 D1213 G-9 D1214 E-7 D1215 H-11 IC1100 B-6 IC1101 B-9 IC1102 B-11 IC1200 G-6 IC1201 I-8 PC1100 B-8 PC1101 B-8 PC1102 I-7 PC1200 H-7 Q1100 F-10 Q1101 G-11 Q1102 B-7 Q1200 E-6 Q1203 H-10 Q1204 G-10 Q1205 G-10 Q1206 I-10 • Semiconductor Location (Page 43) (Page 49) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 68 68 HCD-GNZ77D/GNZ88D HCD-GNZ77D/GNZ88D (Page 53) 6-39. SCHEMATIC DIAGRAM — POWER SECTION (HCD-GNZ88D) — 1.5kV T6.3AL 250V C1138 C1134 D1116 D1115 R1126 R1106 R1200 C1200 C1213 C1210 C1209 D1207 R1111 R1109 D1100 CNP1100 C1127 IC1200 R1116 IC1102 R1138 R1137 R1103 C1221 D1120 IC1100 JR1101 R1203 JR1103 JR1105 C1147 JR1108 L1102 IC1101 IC1201 D1110 D1106 D1112 C1107 TP1101 TP1100 LF1101 TP1108 TP1102 TP1107 TP1105 TP1104 TP1106 TP1200 TP1201 D1119 TP1202 L1200 TP1203 C1222 C1101 L1201 C1141 R1119 VD1100 R1120 C1115 C1128 D1114 C1130 R1132 R1131 R1133 R1127 C1129 R1144 R1140 R1114 C1122 R1112 C1120 R1110 C1119 R1202 C1203 R1207 R1208 R1212 C1206 C1207 C1208 R1211 R1214 R1201 R1145 C1116 C1212 R1216 R1215 R1225 R1217 C1214 R1218 R1223 R1230 R1227 R1228 R1229 R1232 C1139 CN1101 C1219 C1217 R1139 C1140 R1135 R1136 C1218 C1117 R1105 TP1103 SW1100 R1113 C1121 D1118 D1208 R1210 R1209 R1233 R1234 D1205 C1202 C1216 R1226 D1213 R1142 C1149 EP1102 EP1103 PC1101 PC1102 PC1100 EP1200 D1212 PC1200 EP1106 EP1104 FH1100 FH1101 F1100 JW1112 JW1111 JW1109 JW1110 TH1100 JW1105 T1100 D1103 JW1184 JW1107 JW1102 Q1100 Q1101 C1132 D1117 D1215 Q1205 Q1204 JW1173 D1200 D1202 D1204 Q1200 D1203 D1206 D1214 EP1101 EP1105 EP1100 D1109 D1107 C1118 JW1179 D1111 D1122 D1108 T1200 D1211 C1104 C103 C1109 C1110 C1112 D1101 D1102 C1113 L1100 R1122 R1130 R1123 R1124 R1129 R1121 R1146 C1131 R1128 R1117 C1148 C1136 CN1200 R1115 R1141 Q1102 C1220 R1220 R1219 R1221 R1224 Q1203 Q1206 (Page 47) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 69 HCD-GNZ77D/GNZ88D • IC Block Diagrams IC301 AK4358VQ-L (DMB15 Board) IC701 BA6956AN (DRIVER Board) IC712 BA6956AN (DRIVER Board) 12 25 26 27 28 31 29 30 34 35 36 32 33 11 10 9 8 7 6 5 4 3 48 2 1 14 47 46 45 44 43 42 41 40 39 38 37 13 15 16 17 21 18 22 23 24 19 20 DATT AUDIO INTERFACE SDTI4 SDTI1 SDTI2 SDTI3 LRCK I2C SCL SDA CAD1 DCLK DSDL1 DSDR1 DSDL1 DSDR2 DSDL3 DSDR3 DIF0 ROUT4- ROUT4+ (DMIXR) AVSS VREFH AVDD DSDL4 DSDR4 DAC SCF SCF SCF (FR) ROUT1+ DVSS DVDD MCLK BICK PDN ACKSN CAD0 DZF1(SUR) DZF2(R) DZF3(L) LOUT1+ LOUT1+ ROUT1- SCF SCF SCF SCF SCF DATT DAC DATT CONTROL REGISTER DAC DATT DAC DATT DAC DATT DAC DATT DATT DAC DAC (FL) (SL) LOUT2+ LOUT2- (SR) ROUT2+ ROUT2- (FC) LOUT3+ LOUT3- (SW) ROUT3+ ROUT3- (DMIXL) LOUT4+ LOUT4- 1 2 3 4 5 6 7 8 9 CONTROL LOGIC TSD VREF OUT2 OUT1 RNF VM VCC FIN GND RIN www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 70 HCD-GNZ77D/GNZ88D • IC Pin Descriptions IC102 CXD9849R (CD/DVD RF AMP, FOCUS/TRACKING ERROR AMP, DVD SYSTEM PROCESSOR, DIGITAL SERVO PROCESSOR) (DMB15 BOARD (3/5)) Pin No. Pin Name I/O Pin Description 1 AGND — Ground pin 2 DVDA I AC coupled input path A 3 DVDB I AC coupled input path B 4 DVDC I AC coupled input path C 5 DVDD I AC coupled input path D 6 DVDRFIP I AC coupled DVD RF signal input RFIP 7 DVDRFIN I AC coupled DVD RF signal input RFIN Not used in this set. (Open) 8 NA I DC coupled main-beam RF signal input A 9 NB I DC coupled main-beam RF signal input B 10 MC I DC coupled main-beam RF signal input C 11 MD I DC coupled main-beam RF signal input D 12 SA I DC coupled sub-beam RF signal input A Not used in this set. (Open) 13 SB I DC coupled sub-beam RF signal input B Not used in this set. (Open) 14 SC I DC coupled sub-beam RF signal input C Not used in this set. (Open) 15 SD I DC coupled sub-beam RF signal input D Not used in this set. (Open) 16 CDFON I CD focusing error negative input Not used in this set. (Open) 17 CDFOP I CD focusing error positive input Not used in this set. (Open) 18 TNI I 3 beam satellite PD signal negative input 19 TPI I 3 beam satellite PD signal positive input 20 MDI1 I Laser power PD monitor signal input 21 MDI2 I Laser power PD monitor signal input 22 LDO2 O Laser drive signal output 23 LDO1 O Laser drive signal output 24 SVDD3 — Power Supply pin (+3.3 V) 25 CSD O Central servo, Positive main beam summing signal output Not used in this set. (Open) 26 RFLVL O RFRP low pass, or Positive main beam summing signal output Not used in this set. (Open) 27 SGND — Ground pin 28 V2REFO O Reference voltage 2.8 V 29 V2O O Reference voltage 2.0 V 30 VREFO O Reference voltage 1.4 V 31 FEO O Focus error monitor signal output Not used in this set. (Open) 32 TEO O Tracking error monitor signal output Not used in this set. (Open) 33 TEZISLY O TE Slicing Level Not used in this set. 34 OPOUT O Op amp output Not used in this set. (Open) 35 OPIN I Op amp negative input Not used in this set. (Open) 36 OPIN I Op amp positive input Not used in this set. (Open) 37 DMO O Disk motor control signal output. PWM signal output 38 FMO O Feed motor signal control. PWM signal output 39 TROPENPWM O Tray PWM output/Tray open signal output. 40 IOPMON I General PWM signal input 41 TRO O Tracking servo signal output 42 FOO O Focus servo signal output 43 DVSS — Ground pin 44 NC — Not used. (Open) 45 NC — Not used. (Open) 46 DVDD3 — Power Supply pin (+3.3 V) 47 SPFG I Motor Hall sensor signal input 48 DSEL O Select signal output www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 71 HCD-GNZ77D/GNZ88D Pin No. Pin Name I/O Pin Description 49 WIDE I Wide signal output 50 MSW O Volume control signal output 51 MAMUTE O MAMUTE signal output to System Controller Not used in this set. (Open) 52 DVDD18 — Power Supply pin (+1.8 V) 53 to 58 IOA 2 to 7 O Address bus 2 to 7 output to PROM 59 HIGHA0 O Address bus 8 output to PROM 60, 61 IOA18, 19 O Address bus 18, 19 output to PROM 62 DVSS — Ground pin 63 APLLCAP I APLL External Capacitance connection 64 APLLVSS — Ground pin 65 VDD3 — Power Supply pin (+3.3 V) 66 IOWA O WE signal output to PROM 67 A16 O Address bus 16 output to PROM 68 to 72 HIGHA 7 to 3 O Address bus 15 to 11 output to PROM 73 DVDD3 — Power Supply pin (+3.3 V) 74, 75 HIGHA 2, 1 O Address bus 10, 9 output to PROM 76 IOA20 O Address bus 20 output to PROM 77 IOCS O CE signal output to PROM 78 IOA1 O Address bus 1 output to PROM 79 IOOE O OE signal output to PROM 80 DVDD3 — Power Supply pin (+3.3 V) 81 to 84 AD 0 to 3 I Data bus 0 to 3 input from PROM 85 DVSS — Ground pin 86 to 88 AD 4 to 6 I Data bus 4 to 6 input from PROM 89 IOA21 O Address bus 21 output to PROM 90 ALE O Address latch enable Not used in this set. (Open) 91 AD7 I Data bus 7 input from PROM 92 A17 O Address bus 17 output to PROM 93 IOA0 O Address bus 0 output to PROM 94 DVSS — Ground pin 95 UWA I System Controller write strobe Not used in this set. (Open) 96 URB I System Controller read strobe Not used in this set. (Open) 97 DVDD18 — Power Supply pin (+1.8 V) 98 IFSDO I DVD SOD signal input from System Controller 99 IFCK O DVD SCO signal output to System Controller 100 XIFCS I DVD XIFCS signal input from System Controller 101 IFSDI I VIFBUSY signal output from System Controller 102 SCL O SCL signal output to EEPROM 103 SDA O SDA signal output to EEPROM 104 TRG-SW O RS232 RXD signal output Not used in this set. (Open) 105 IFBSY I RS232 TXD signal input from System Controller 106 RXD I RD232 RXD clock 107 TXD I RD232 TXD data 108 DVDD3 — Power Supply pin (+3.3 V) 109 ICE I ICE mode enable Not used in this set. (Open) 110 PRST I MTRST signal input from System Controller 111 IR I IR control signal input Not used in this set. (Open) 112 INT0 I External interrupt0 Not used in this set. (Open) 113 DQMO O DQM0 signal output to SD-RAM 114 MREQ I DQM signal input 115 RD7 I Data bus 7 from SD-RAM 116 DVSS — Ground pin 117, 118 RD 6, 5 I Data bus 6, 5 from SD-RAM www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 72 HCD-GNZ77D/GNZ88D Pin No. Pin Name I/O Pin Description 119 DVSS — Ground pin 120, 121 RD 4, 3 I Data bus 4, 3 from SD-RAM 122 DVDD18 — Power Supply pin (+1.8 V) 123 to 125 RD 2 to 0 I Data bus 2 to 0 from SD-RAM 126 RD15 I Data bus 15 from SD-RAM 127 DVDD3 — Power Supply pin (+3.3 V) 128 RD 14 I Data bus 14 from SD-RAM 129 to 133 RD 13 to 9 I Data bus 13 to 9 from SD-RAM 134 DVSS — Ground pin 135 RD8 I Data bus 8 from SD-RAM 136 GPI0 — Not used in this set. (Open) 137 DQM1 O DQM1 signal output to SD-RAM 138 REW O WE signal output to SD-RAM 139 CAS O CAS signal output to SD-RAM 140 RAS O RAS signal output to SD-RAM 141 DVDD3 — Power Supply pin (+3.3 V) 142 RCS O RCS signal output to SD-RAM 143 BAO O BAO signal output to SD-RAM 144 DVSS — Ground pin 145 BA1 O BA1 signal output to SD-RAM 146 RA10 O Address bus 10 output to SD-RAM 147 RA0 O Address bus 0 output to SD-RAM 148 DVSS — Ground pin 149 to 151 RA 1 to 3 O Address bus 1 to 3 output to SD-RAM 152 DVDD18 — Power Supply pin (+1.8 V) 153 NC — Not used. (Open) 154 NC — Not used. (Open) 155 DVDD3 — Power Supply pin (+3.3 V) 156 RCLK O CLK signal output to SD-RAM 157 CKE O CKE signal output to SD-RAM 158 to 160 RA 11 to 8 O Address bus 11 to 8 output to SD-RAM 161 DVSS — Ground pin 162 RA7 O Address bus 7 output to SD-RAM 163 DVSS — Ground pin 164 to 166 RA 6 to 4 O Address bus 6 to 4 output to SD-RAM 167 DVDD3 — Power Supply pin (+3.3 V) 168 DISC/X — Not used in this set. (Open) 169 RGB O RGB control signal output Not used in this set. (Open) 170 TSD M O TSDM signal output 171 NC — Not used in this set. (Open) 172 NC — Not used in this set. (Open) 173 DVDD18 — Power Supply pin (+1.8 V) 174 FWD — Not used in this set. (Open) 175 NC — Not used. (Open) 176 LIMSW O LIMSW signal output to Optical pick-up 177 OCSW I SEN signal input from System Controller/OCSW signal input Not used. (Open) 178 REW — Not used in this set. (Open) 179 CKSW I CKSW signal input Not used in this set. (Open) 180 NC — Not used in this set. (Open) 181 NC — Not used in this set. (Open) 182 DVDD3 — Power Supply pin (+3.3 V) 183 NC — Not used in this set. (Open) 184 NC — Not used in this set. (Open) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 73 HCD-GNZ77D/GNZ88D Pin No. Pin Name I/O Pin Description 185 NC — Not used in this set. (Open) 186 NC — Not used in this set. (Open) 187 NC — Not used in this set. (Open) 188 NC — Not used in this set. (Open) 189 DAVCC — Power Supply pin (+3.3 V) 190 VREF I Bandgap reference voltage Not used in this set. (Open) 191 FS O Full scale adjustment (pull down) 192 YUV0 — Not used in this set. (Open) 193 DAVSS — Ground pin 194 YUV1 O Y signal output to VIDEO AMP 195 DAVDD — Power Supply pin (+3.3 V) 196 YUV2 O CHROMA signal output to VIDEO AMP 197 DAVSS — Ground pin 198 YUV3 O VIDEO signal output to VIDEO AMP 199 DAVDD — Power Supply pin (+3.3 V) 200 YUV4 O G signal output to VIDEO AMP 201 DAVSS — Ground pin 202 YUV5 O B signal output to VIDEO AMP 203 YUV6 O R signal output to VIDEO AMP 204 DVDD3 — Power Supply pin (+3.3 V) 205 MIC/VSYNC I Microphone status signal input 206 VOICE/YUV7 I Karaoke voice signal input 207 KRMOB/HSYNC O Karaoke mode detection signal output 208 SMSCK I Karaoke score signal input 209 SPDATA/SMSDI I Audio data of SPDIF input 210 MUTE O Mute signal output 211 MUTE123 O Mute signal output 212 DVDD3 — Power Supply pin (+3.3 V) 213 ALRCK I Audio left/right channel clock signal input 214 ABCK O Audio bit clock signal output 215 ACLK I Audio DAC master clock signal input 216 DVSS — Ground pin 217 ASDATA0 O Auio serial data signal output 218 ASDATA1 O Auio serial data signal output 219 ASDATA2 O Auio serial data signal output 220 XRST O Reset signal output 221 DVDD18 — Power Supply pin (+1.8 V) 222 ASDATA4 O Auio serial data signal output 223 DVSS — Ground pin 224 DWIDE — Not used in this set. (Open) 225 SDPIF O SPDIF signal output 226 RFGND18 — Ground pin 227 RFVDD18 — Power Supply pin (+1.8 V) 228 ZTALO O Oscillator signal output (27 MHz) 229 ZTALI I Oscillator signal input (27 MHz) 230 JITFO O RF jitter meter output 231 JITFN I Negative input of operation amplifier for RF jigger meter 232 PLLVSS — Ground pin 233 IDAC — Not Used. 234 PLLVDD3 — Power Supply pin (+3.3 V) 235 LPFON O Negative output of loop filter amplifier 236 LPFIP I Positive input of loop filter amplifier 237 LPFIN I Negative input of loop filter amplifier www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 74 HCD-GNZ77D/GNZ88D Pin No. Pin Name I/O Pin Description 238 LPFOP O Positive output of loop filter amplifier 239 VDD3 I Power Supply pin (+3.3 V) 240 NC — Not used. (Open) 241 VSS — Ground pin 242 NC — Not used. (Open) 243 NC — Not used. (Open) 244 RFVDD3 — Power Supply pin (+3.3 V) 245 RFRPDC I RFRP signal input 246 RFRPAC I RFRP signal input 247 HRFZC I High frequency RF ripple zero crossing 248 CRTPLP O Defect level filter capacitor connecting 249 RFGND — Ground pin 250 NC — Not used. (Open) 251 NC — Not used. (Open) 252 OSP O RF offset cancellation capacitor connecting 253 OSN I RF offset cancellation capacitor connecting 254 RFGC O RF offset loop capacitor connecting for DVD-ROM 255 IREF I Current reference input 256 AVDD3 — Power Supply pin (+3.3 V) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 75 HCD-GNZ77D/GNZ88D IC401 M30622MEP-A50FPU0 (SYSTEM CONTROL) (MAIN BOARD (1/4)) Pin No. Pin Name I/O Pin Description 1 SW CHANNEL O Signal path selection signal for sub woofer channel SELECT “L”: LFE, “H”: Subwoofer out from M61537 2 SURR CHANNEL O Signal path selection signal for surround channel SELECT “L”: SL/FR (MTK), “H”: Tone out from M61537 3 SM LATCH 3 O Serial data latch pulse output to the S-Master Processor 4 SIRCS I Remote control signal input 5 NO USE I Not used. (Open) 6 NO USE I Not used. (Open) 7 NO USE I Not used. (Open) 8 BYTE — Ground pin 9 CNVSS — Ground pin 10 XC IN I Sub system clock input (32.768 kHz) 11 XC OUT O Sub system clock output (32.768 kHz) 12 RESET I System reset signal input from the reset signal IC “L”: reset After the power supply rises, “L” is input for several hundreds msec and then change to “H”. 13 X OUT O Main system clock output (5 MHz) 14 VSS — Ground pin 15 X IN I Main system clock input (5 MHz) 16 VCC — Power supply pin (+3.3 V) 17 NMI I Non-maskable interrupt input 18 NO USE I Not used. (Connect to ground.) 19 NO USE I Not used. (Open) 20 AC CUT I AC off detection signal input from the reset signal IC “L”: AC Cut detected 21 VIDEO MUTE O Video muting on/off control signal output “L”: muting on 22 VIDEO OUT SW O Composite video output switching output control “L”: DVD VIDEO output, “H”: VIDEO VIDEO input 23 MIC DETECT I Microphone connection detection signal input “L”: headphone connected 24 KRMOD I Karaoke Mode detection signal input 25 MIC STATUS O Microphone status output to DVD Motherboard “L”: Microphone is not connected, “H”: Microphone is connected 26 MTK RESET O Reset signal output to DVD Motherboard “L”: reset 27 MTK XIFCS I Communication Initialization Request Acknowledgement Signal from DVD Motherboard 28 MTK BUSY O Communication Initialization Request Signal to DVD Motherboard 29 IIC CLK I/O Clock signal for IIC communication between the microcomputer and the IIC checker 30 IIC DATA I/O Data signal for IIC communication between the microcomputer and the IIC checker 31 MTK SIO O Serial data output signal to DVD Motherboard 32 MTK SOD I Serial data input signal from DVD Motherboard 33 MTK CLK I Serial data clock signal to DVD Motherboard 34 DVD A MUTE O DVD analog signal muting on/off control signal output “H”: muting on 35 MTK POWER O Power supply control signal to DVD Motherboard “H”: Power supply on 36 ST CE O PLL chip enable signal output to the tuner unit 37 MC DIN I PLL serial data input from the tuner unit 38 ST CLK O PLL serial data transfer clock signal output to the tuner unit 39 ST DIN/MC DOUT O PLL serial data output to the tuner unit 40 TUNED I Tuning detection signal input from the tuner unit “L”: tuned 41 OPEN SW I Eject detection signal input from CDM 42 TBL SENSE I Disc tray position detection signal input from CDM 43 E3 I Disc tray status detection signal input from CDM 44 E2 I Disc tray status detection signal input from CDM 45 E1 I Disc tray status detection signal input from CDM 46 TM F O CDM turning motor control signal output www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 76 HCD-GNZ77D/GNZ88D Pin No. Pin Name I/O Pin Description 47 TM R O CDM turning motor control signal output 48 LM F O CDM loading motor control signal output 49 LM R O CDM loading motor control signal output 50 LED ILLUMINATION 1 O Dynamic LED drive signal output to the ILLUMINATION 1st indicator and 2nd indicator “H”: LED on 51 LED ILLUMINATION 2 O Dynamic LED drive signal output to the ILLUMINATION 3rd indicator and 4th indicator “H”: LED on 52 LED ILLUMINATION 3 O Dynamic LED drive signal output to the ILLUMINATION 5th indicator and 6th indicator “H”: LED on 53 LED CTRL O Dynamic LED drive select signal output 54 VOL A I Jog dial pulse input from the VOLUME rotary encoder (A phase input) 55 VOL B I Jog dial pulse input from the VOLUME rotary encoder (B phase input) 56 STBY LED O LED drive signal output of POWER indicator “H”: LED is turned on 57 FL DRIVER DATA O Serial data output signal to FL Driver, NJU3427 58 FL DRIVER CLK O Serial data clock signal to FL Driver, NJU3427 59 FL DRIVER RESET O Serial data reset signal to FL Driver, NJU3427 60 FL DRIVER CS O Serial data chip select signal to FL Driver, NJU3427 61 SW LED O LED drive signal output of SUB WOOFER ON indicator “H”: LED ON 62 VCC — Power supply pin (+3.3 V) 63 A HALF I Deck A cassette detection signal input “H”: cassette detected 64 VSS — Ground pin 65 SM RESET O Reset signal output to the S-Master Power IC 66 IO EXP DATA OUT O Serial data output signal to I/O expander, BH2210V 67 NO USE I Not used. (Connect to ground.) 68 IO EXP RST O Reset signal output to the I/O expander, BH2210V 69 IO EXP CLK O Serial data latch signal to I/O expander, BH2210V 70 IO EXP LAT O Serial data clock signal to I/O expander, BH2210V 71 NO USE I Not used. (Connect to ground.) 72 SM SD I Shutdown (protector) detection signal from the S-Master power IC 73 DISPLAY KEY I DISPLAY key press detection signal (Interrupt input) 74 POWER KEY I POWER key press detection signal (Interrupt input) 75 NO USE I Not used. (Connect to ground.) 76 SM LATCH 1 O Serial data latch pulse output to the S-Master Processor 77 SM CLK O Serial data transfer clock signal to the S-Master Processor IC (CXD9843) 78 SM DATA O Serial data output signal to the S-Master Processor IC (CXD9843) 79 SM LATCH 2 O Serial data latch pulse output to the S-Master Processor 80 NO USE I Not used. (Connect to ground.) 81 NO USE/SW MUTE O GNZ88D: Not used. (Connect to ground.), GNZ77D: Subwoofer mute signal output 82 OUT2DLY SEL I PWM Mode selection signal “L”: PWM Mode 3, “H”: PWM Mode 4 83 M61537 DATA O Serial data output to audio signal processor, M61537FP 84 M61537 CLK O Serial data transfer clock signal output to audio signal processor, M61537FP 85 HP DET I Headphone connection detection signal input “H”: headphone connected 86 HP MUTE O Headphone muting on/off control signal “H”: muting on 87 NO USE I Not used. (Connect to ground.) 88 VACS IN I VACS level detection signal 89 A SHUT I Shut off detection signal input from deck A side reel pulse detector (A/D input) 90 B SHUT I Shut off detection signal input from deck B side reel pulse detector (A/D input) 91 B HALF I Deck B cassette detection and forward side recording tab detection signal input (A/D input) 92 MODEL IN I Model setting (A/D input) 93 DEST IN I Destination setting (A/D input) 94 AD KEY 3 I Key signal input (A/D input) 95 AD KEY 2 I Key signal input (A/D input) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 77 HCD-GNZ77D/GNZ88D Pin No. Pin Name I/O Pin Description 96 AVSS — Ground pin 97 AD KEY 1 I Key signal input (A/D input) 98 VREF I A/D Converter reference voltage input (+3.3 V) 99 AVCC — Power supply pin (+3.3 V) (for A/D conversion) 100 MAIN ON/OFF O Main power on/off control signal output “H”: power on www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 78 HCD-GNZ77D/GNZ88D IC403 BH2210FV-E2 (SIGNAL IN/OUT CONTROL) (MAIN BOARD (2/4)) Pin No. Pin Name I/O Pin Description 1 CTLIO I IN/OUT control port (Fixed at “H” in this set.) 2 RESET I Reset signal input 3 CLK I Serial data clock signal input 4 LATCH I Serial data latch signal input 5 TC-MUTE O Tape playback muting on/off control signal output “H”: muting on 6 NO USE O Not used. (Open) 7 REC MUTE O Recording muting on/off control signal output “L”: muting on 8 NO USE O Not used. (Open) 9 SM-NSP-MUTING O S master processor IC PWM 50% duty muting on/off control signal output “L”: muting on 10 SM-SOFT-MUTING O S master processor IC soft muting on/off control signal output “L”: muting on 11 SM-PG-MUTE O S master processor IC PWM muting on/off control signal output “L”: muting on 12 SM-INIT O Initialization signal to the S master processor IC 13 LATCHO O Serial data latch output signal Not used. (Open) 14 CLKO O Serial data clock signal output Not used. (Open) 15 DO1 O Serial data signal output 1 Not used. (Open) 16 DI2 I Serial data signal input 2 Not used. (Connect to ground.) 17 A-TRIG O Deck A side trigger plunger drive signal output “H”: plunger on 18 CAMP-CNT O Capstan motor drive signal output 19 B-TRIG O Deck B side trigger plunger drive signal output “H”: plunger on 20 REC BIAS O Recording bias on/off control signal output “H”: bias on 21 TC RELAY O Recording/playback selection signal output “H”: recording, “L”: playback 22 ADC RESET O Power down control signal to analog to digital converter “L”: power down 23 NO USE O Not used. (Open) 24 FAN CTRL O Fan driving signal output “L”: fan on 25 DO2 O Not used. (Open) 26 DI1 I Serial data signal input 27 VSS — Ground pin 28 VDD — Power supply pin (+3 V) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com