SERVICE MANUAL NETWORK AUDIO SYSTEM US Model AEP Model UK Model HCD-CZ1/NAS-CZ1 Ver. 1.1 2005.08 SPECIFICATIONS 9-879-721-02 2005H05-1 © 2005.08 Sony Corporation Audio Group Published by Sony Engineering Corporation Model Name Using Similar Mechanism NEW CD Base Unit Name BU-K7BD81B Optical Pick-up Block Name KSM-213EDP • HCD-CZ1 is the amplifier, CD player and tuner section in NAS-CZ1. Main unit Amplifier section For the U.S.A. model AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6-ohm loads, both channels driven, from 120 – 10,000 Hz; rated 10 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milli watts to rated output. European model: DIN power output (rated): 7.5 + 7.5 watts (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 10 + 10 watts (6 ohms at 1 kHz, 10% THD) Inputs ANALOG IN (mini jack): Sensitivity 450 mV, impedance 10 kilohms Outputs PHONES (mini jack): accepts headphones with an impedance of 8 ohms or more CD player section System Compact disc and digital audio system Laser Semiconductor laser (λ=770 – 810 nm) Emission duration: continuous Frequency response 2 Hz – 20 kHz (±0.5 dB) Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range U.S.A. model: 87.5 – 108.0 MHz (100-kHz step) European models: 87.5 – 108.0 MHz (50-kHz step) Antenna FM lead antenna Antenna terminals 75 ohms unbalanced Intermediate frequency 10.7 MHz AM tuner section Tuning range U.S.A. model: 530 – 1,710 kHz (with the tuning interval set at 10 kHz) 531 – 1,710 kHz (with the tuning interval set at 9 kHz) European model: 531 – 1,602 kHz (with the tuning interval set at 9 kHz) Antenna AM loop antenna Antenna terminals External antenna terminal Intermediate frequency 450 kHz Speaker section Speaker system 2-way, Acoustic Suspension type Speaker units Woofer: 9 cm dia., cone type Tweeter: 2.5 cm dia., balanced- dome-type Nominal impedance 6 ohms General Power requirements U.S.A. model: 120 V AC, 60 Hz European model: 230 V AC, 50/60 Hz Power consumption U.S.A. model: 40 watts European model: 40 watts 0.3 watts (in Power Saving mode) Dimensions (w/h/d) incl. projecting parts and controls Approx. 460 × 175 × 190 mm Mass Approx. 5.3 kg Supplied accessories Remote Commander with battery (1) AM loop antenna (1) FM lead antenna (1) Network cable (1) M-crew Server CD-ROM (1) Design and specifications are subject to change without notice. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 2 HCD-CZ1/NAS-CZ1 Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 ˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) Fig. A. Using an AC voltmeter to check AC leakage. 1.5 kΩ 0.15 µF AC voltmeter (0.75 V) To Exposed Metal Parts on Set Earth Ground SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. The following caution label is located inside the unit. This appliance is classified as a CLASS 1 LASER product. This marking is located on the bottom exterior. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 3 HCD-CZ1/NAS-CZ1 TABLE OF CONTENTS 1. SERVICE NOTE................................................................. 4 2. GENERAL.......................................................................... 15 3. DISASSEMBLY 3-1. Disassembly Flow ............................................................ 17 3-2. Speaker Grill (F/R) Assy, Top Panel Assy ........................ 18 3-3. Cover Bottom Assy........................................................... 18 3-4. Rear Panel Section............................................................ 19 3-5. Front Panel Section .......................................................... 20 3-6. Top Panel Section ............................................................. 20 3-7. Base Unit (BU-K7BD81B) .............................................. 21 3-8. MAIN Board Section........................................................ 21 3-9. ETHER Board, MAIN Board ........................................... 22 4. TEST MODE ...................................................................... 23 5. ELECTRICAL ADJUSTMENTS................................. 26 6. DIAGRAMS 6-1. Block Diagram – SERVO Section – ................................ 27 6-2. Block Diagram – Ethernet Section – ............................... 28 6-3. Block Diagram – MAIN Section – .................................. 29 6-4. Printed Wiring Board – CD Board – .............................. 31 6-5. Schematic Diagram – CD Board – .................................. 32 6-6. Printed Wiring Board – ETHER Board – ........................ 33 6-7. Schematic Diagram – ETHER Board –........................... 34 6-8. Printed Wiring Board – MAIN Board (Component Side) – ................................ 35 6-9. Printed Wiring Board – MAIN Board (Conductor Side) – .................................. 36 6-10. Schematic Diagram – MAIN Board (1/2) – .................... 37 6-11. Schematic Diagram – MAIN Board (2/2) – .................... 38 6-12. Printed Wiring Boards – Power Section – ....................... 39 6-13. Schematic Diagram – Power Section – ........................... 40 6-14. Printed Wiring Boards – Panel Section – ........................ 41 6-15. Schematic Diagram – Panel Section – ............................ 42 6-16. Printed Wiring Board – FL Board – ................................ 43 6-17. Schematic Diagram – FL Board – ................................... 44 7. EXPLODED VIEWS 7-1. Speaker Grill, Top Panel Section ...................................... 54 7-2. Front Panel Section .......................................................... 55 7-3. Rear Panel Section............................................................ 56 7-4. CD Panel Section.............................................................. 57 7-5. PSAMP Board Section ..................................................... 58 7-6. MAIN Board Section........................................................ 59 7-7. Base Unit (BU-K7BD81B) .............................................. 60 8. ELECTRICAL PARTS LIST......................................... 61 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 4 HCD-CZ1/NAS-CZ1 NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT SECTION 1 SERVICING NOTES MODEL IDENTIFICATION MODEL Power Voltage Incdication US model AC: 120 V 60 Hz 25 W AEP, UK models AC: 230 V - 50/60 Hz 25 W Fig.1 Method to push the S601 NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) S601 The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 ˚C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 ˚C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. LASER DIODE AND FOCUS SEARCH OPERATION CHECK During normal operation of the equipment, emission of the laser diode is prohibited unless the upper lid is closed while turning ON the S601. (push switch type) The following checking method for the laser diode is operable. • Method Emission of the laser diode is visually checked. 1. Open the upper lid. 2. Push the S601 as shown in Fig.1. Note: Do not push the detection lever strongly, or it may be bent or damaged. 3. Press the B button. 4. Check the object lens for confirming normal emission of the laser diode. If not emitting, there is a trouble in the automatic power control circuit or the optical pick-up. In this operation, the object lens will move up and down 2 times along with inward motion for the focus search. Power voltage indication – Bottom View – www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 5 HCD-CZ1/NAS-CZ1 NETWORK CHECK 1. Apparatuses And Materials Prepared (1) Personal computer with OS “Windows XP” (must satisfy the conditions mentioned on pages 5 and 6 of Installation Instructions for M-crew Server ver 1.1 (refer to page 9 of this service manual)) (2) M-crew Server CD-ROM (for install) (3) LAN cable - Must comply with Category 5; - If the set is directly connected to a personal computer: Use a cross cable; - If the set is connected to a personal computer via router of hub; - Use the LAN cable attached (part No. 1-827-478-11, 5m, straight) or LAN cable that complies with the Category 5. 2. Network Connection Check 2.1 Installing the M-crew Server - Install the M-crew Server from the CD-ROM.(for the procedure, see pages 8 to 10 of the Installation Instructions for M-crew Server ver1.1 (refer to page 9 to 10 of this service Section manual) - Use a sample music file created during the installation, if listening to the music. 2.2 Connecting the set to server, and operation check (1) Start the personal computer in which the M-crew Server was installed. (2) Connect the set to the Ethernet connector of personal computer with the LAN cable. (3) Following “Selecting a server” on pages 13 and 14 of the Operating Instructions for NAS-CZ1 (refer to page 11 of this service manual), connect the set to the server. 2.3 Operation check Following the pages 15-17 of the Operating Instructions for NAS- CZ1 (refer to page 11 to 12 of this service manual), check that a music file in the server can be played with the set. If it cannot be played normally, see“3. Remedies in Case of Problems” in the next section. 3. Remedies In Case Of Problems If a problem occurred in “2 Network Connection Check” mentioned above, first check the following two items: (1) Problem and remedies (see pages 31 and 32 of the Operating Instructions for NAS-CZ1) (2) Messages (see page 33 of the Operating Instructions for NAS- CZ1 (refer to page 8 of this service manual)) If the above two items cannot cope with the problem, take the following procedure for checking 3.1 Errors In The Midway Of Server Connection 3.1.1 NETWORK function does not start If the NETWORK function does not start though the [NETWORK] and USER PROFILE [1] to [5] buttons on the set is pressed. (1) Faulty connection between CN651 of MAIN board and CN501 of ETHER board t Check if the connector is inserted obliquely of disconnected. (2) Faulty circuits of ETHER board t Replace the ETHER board and check the operation. If the board is faulty, check the soldering of power line, communication line, etc. - CN501 - FB505, FB508-511, FB515-521 - IC506 - R530, 537 3.1.2 NETWORK function starts but access to network failed or server is not found (1) “Check Network” is displayed t Replace the ETHER board and check the operation. If the board is faulty, the PHY IC (IC501) on the ETHER board may be defective. 3.1.3 “Configuring” is displayed for a long time (1) Check if the connectable serve has started. t If the server has not started yet, start it. (2) It will take 1 to 2 minutes for Windows to automatically get IP address if the set is connected to a personal computer directly and IP address acquisition method is set to “automatic”. For this reason, “Configuring” may be displayed for a long time. t The use of a router with DHCP, for instance, can shorten the time. (3) Communication with the server is disabled and “Configuring” will be displayed for a long time, if network setting of the set is different from that of personal computer. t Make correct network setting. Example: - Set the IP address acquisition of both the set and personal computer to “automatic”. - If the IP address acquisition of either the set or personal computer or both of them is set to “static”, check that the input field of IP address where the subnet mask”255" is set is same between the set and personal computer. If the subnet mask is “255.255.255.0”, three input fields from the top must be same between the set and personal computer. 3.1.4 “No Server” is displayed (1) If the network setting is different between the set and personal computer, “Configuring” is displayed for a long time and then finally “No Server” is displayed. t See the item of 3.1.3(3). www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 6 HCD-CZ1/NAS-CZ1 3.2 Errors After Serve Connection 3.2.1 “Loading” is displayed for a long time (1) When the set is connected to the M-crew Server for the first time, the M-crew Server identifies the HCD-CZ1 individually and creates the profile information in the personal computer, and therefore it will take time for “Loading” t wait for a while as it is until “loading” finishes. (2) When the set is connected to a DLNA server other than M- crew server, if many contents have been stored in that server, it will take time for “loading”. t Though “Loading” will finish after a while, it is recommended that the music be imported with the M- crew Server and the M-crew Server be used as a server. 3.2.2 “Server Error” is displayed (1) If the load on personal computer is large, the communication with the set will not finish within the specified time, resulting in “Serve Error” Display. t Reduce the load on personal computer, and then retry. (2) “Server Error” will be displayed if the server information is refreshed (addition or deletion of music) when you are listening to the music with the set. t Reconnect the set to the server. 3.3 Errors When You Are Listening To The Music 3.3.1 Sounds are interrupted (1) The baud rate will be reduced in the wireless connection t Cable connection is recommended. (2) Check if the music itself registered to the server is interrupted. t Certain ripping software may not be able to encode the music-to-music joints continuously. 3.3.2 Some functions cannot be used (1) If a server other than M-crew Server is used, the following functions cannot be used. Following the pages 13 and 14 of the Operating Instructions for NAS-CZ1 (refer to page 11 of this service manual), select the M-crew Server. - Web Radio - Library Mode switching - Library Search - Favorite - User Profile 3.3.3 “Cannot Play” is displayed (1) If the server does not convert the music into LPCM format for streaming, the set cannot play that music. t You can play the contents supported by the M-crew Server, if the set is connected to the M-crew Server. (2) The contents with DRM may not be processed for streaming. t The contents with DRM are not supported. (3) “Cannot Play” will be displayed if the contents themselves are deleted though the music contents are registered to the server. 3.3.4 Operation becomes slow (1) If it takes time to communicate with the server, the operation of the set may become slow according to that time. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 7 HCD-CZ1/NAS-CZ1 • Operating Instrution for NAS-CZ1 (extract) Connect the power cord to a wall outlet. The demonstration appears in the display. When you press ?/1, the system turns on and the demonstration automatically ends. To turn off the demonstration display Press DISPLAY while the system is off (page 28). You can listen to music stored on the connected media server with this system. You can select your desired Media server to be your default server. Doing so prevents you from having to make the selection each time you use NETWORK function. Tip You can listen to music stored on DLNA-compliant servers with this system. 1 Start up your desired Media server on your computer. 2 Press ?/1 to turn on the system. 3 Press NETWORK. While “Configuring” is flashing in the display, the display is automatically setting. Do not turn off the power during this time. 4 “MEDIA SERVERS?” appears, then press ENTER. 5 Press . or > repeatedly to select the desired Media server, then press ENTER. The selected server is set to the default server. Connecting power cord Enjoying NETWORK function Selecting a server When selecting the M-crew Server as a media server The following marks appears in the display. * These marks also appear when using a server other than M-crew Server. Note You can use the following functions only when using the M-crew Server as a media server. – MUSIC LIBRARY – LIBRARY SEARCH – PLAYLIST MODE – FAVORITE PLAYLIST – User Profile – WEB RADIO Tip You can redo the default server selection to select a different server (page 19). Checking the network status Tip When the network lamp flashes quickly, a message also appears in the display at this time (see page 33). To check the message again, press ENTER or another button while [NET] appears in the display. Network lamp System status The system is communicating with the server. The NETWORK function is being used. An error has occurred. The server selected now* network lamp flashes slowly lights up flashes quickly You can listen to music stored on your computer through the system’s speaker. Make sure you have registered audio data to the media server. 1 Press NETWORK repeatedly to switch the function to MUSIC LIBRARY. 2 Press LIBRARY MODE repeatedly until the mode you want appears. 3 Press N. Note Some time may be required before playback starts depending on the number of tracks registered to the server. Other operations Note The X and m/M buttons may not work for some tracks when using a server other than M-crew Server. MUSIC LIBRARY Listening to music stored on your computer 1 2 3 ALBUM +/– ./> x m/M X 1/ALL REPEAT (Disc mode) (Artist mode) (Playlist mode) Select To play (Disc mode) Mode for listening to albums sorted according to the disc information of the tracks (Artist mode) Mode for listening to albums sorted according to the artist information of the tracks (Playlist mode) Mode for listening to playlists created by M-crew Server and the favorite playlists registered on the M-crew Server. To Do this Stop play Press x. Pause Press X. Press again to resume play. Select an album Press ALBUM +/– repeatedly. Select a track Press . or > repeatedly. Find a point in a track Keep pressing m or M during playback and release it at the desired point. Play repeatedly (Repeat Play) Press REPEAT repeatedly during playback until “REP” or “REP1” appears. REP: For all registered tracks. REP1: For a single track only. To cancel Repeat Play, press REPEAT repeatedly until both “REP” and “REP1” disappear. Play all tracks only in the selected album Press 1/ALL repeatedly until “1ALBM” appears. To play all registered tracks, press 1/ALL repeatedly until “ALL ALBM” appears. You can search for an album in either DISC MODE or ARTIST MODE. 1 Press NETWORK repeatedly to switch the function to MUSIC LIBRARY. 2 Press LIBRARY MODE repeatedly until “ (Disc mode)” or “ (Artist mode)” appears. 3 Press LIBRARY SEARCH. “LIBRARY SEARCH” appears about a second, then “SEARCH” lights up. 4 Repeat the following to search for the album. 5 Press ENTER or N. Playback starts from the first track in the selected album. Notes Y ou cannot use the Library Search function with a media server other than the supplied M-crew Server. Y ou cannot search for an album in PLAYLIST MODE. You can listen to tracks registered in the PLAYLIST album on your computer. 1 Press NETWORK repeatedly to switch the function to MUSIC LIBRARY. 2 Press LIBRARY MODE repeatedly until “ (Playlist mode)” appears. 3 Press ALBUM +/– repeatedly to select a desired playlist. 4 Press N. Note Some time you may not be able to use the Playlist library function with a media server other than the supplied M-crew Server. Searching for an album – L IBRARY SEARCH To do Press Change the character at the cursor position (flashing character) ./> repeatedly Move the cursor position CURSORT or CURSORt repeatedly Display albums with titles that match the characters from the start to the cursor position ALBUM +/– repeatedly Listening to music in a play list – P LAYLIST www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 8 HCD-CZ1/NAS-CZ1 What is a FAVORITE PLAYLIST? By registering tracks on your computer to a favorite list using this system, you can play back only the tracks you want to listen to. One favorite playlist can be created for each profile, and each favorite playlist can contain up to 100 tracks. To register tracks to a favorite playlist and playing 1 During the playback or play pause of the desired track, press FAVORITE ADD. “FAVORITE” appears. 2 After “FAVORITE” disappears, repeat step 1 to register the desired tracks. Playing favorite playlist 1 Press NETWORK repeatedly to switch the function to MUSIC LIBRARY. 2 Press FAVORITE CALL. Play starts. Tip You can also play the favorite playlist through the following procedure: 1. Press LIBRARY MODE repeatedly until “ (Playlist mode)” appears. 2. Press ALBUM +/– repeatedly until “FAVORITE” appears. To delete tracks from a favorite list 1 Press N or X to play or pause the track you want to delete from a favorite playlist. 2 Press FAVORITE DELETE. “DELETE?” appears. 3 Press ENTER. “Deleting” appears, then “Complete!” appears. Notes • If you edit a track in an album that is registered to a FAVORITE PLAYLIST on your computer, the track is erased from the FAVORITE PLAYLIST automatically. (except when you changed the track name) • During the playback of a track in a favorite playlist, you cannot press FAVORITE ADD to register the track to a favorite playlist. • When you press FAVORITE DELETE, the track is erased from the FAVORITE PLAYLIST but remains in the Music Library. Listening to music in a favorite list – FAVORITE PLAYLIST Registration/ FAVORITE PLAYLIST Play FAVORITE DELETE 1 FAVORITE CALL ENTER Should you encounter a problem with your system, do the following: 1 Make sure the power cord is correctly and firmly connected. 2 Find your problem in the troubleshooting checklist below and take the indicated corrective action. If the problem persists after doing all of the above, consult your nearest Sony dealer. General The display starts flashing as soon as you plug in the power cord even though you have not turned on the system (see step 2 of “Connecting power cord” (page 13)). Press ?/1 while the system is off. The demonstration disappears. The radio presetting is canceled. Redo “Presetting radio stations” (page 24). There is no sound. Press VOL + or VOLUME + on the system. Make sure the headphones are not connected. There is severe hum or noise. Move the system away from the source of noise. Connect the system to a different wall outlet. Install a noise filter (commercially available) to the power cord. The remote does not function. Remove the obstacle. M ove the remote closer to the system. P oint the remote at the system’s sensor. Replace the CR2025 battery. Locate the system away from the fluorescent light. The system can not be turned on even though you have pressed ?/1. Make sure the power cord is connected to a wall outlet. The color irregularity on a TV screen appears. Turn off the TV set once, then turn it on after 15 to 30 minutes. If the color irregularity still persists, place the speakers farther away from the TV set. Network The desired server cannot be found. • Check the network settings on your computer. • Start up the server you want to use on your computer. • Check the network settings. • Set the broadband router or hub again correctly. For details, see the instruction manual of the broadband router or hub. • When setting a firewall other than that provided with the OS, refer to Troubleshooting in the Installation Manual included on the supplied CD-ROM. • Reduce the number of servers that can be connected to 10 servers or less (page 21). • Replace the Ethernet cable with a new one. • Follow the procedure below and reconnect to the server. 1. Select “MEDIA SERVERS?” in the network menu (page 19), then press ENTER. 2. Press ./> repeatedly to select the desired media server, then press ENTER. Tracks registered to a server cannot be selected by the system. • Track selection, playback and other operations on the system side may not be possible for servers other than M-crew Server (page 13). The sound skips. Sound skipping may occur in the following cases: – When music is being recorded onto the server – When the computer is running many applications – When the network status is crowded – When multiple systems are performing playback simultaneously Track names are not displayed. • Some types of input characters cannot be displayed by the system, even if they can be registered and displayed on the server. Operation commands take time. • Depending on the condition of the server, it may take a while until operation proceeds. For example, when there is no response after pressing m/M, keep pressing m/M for a while. Afterwards, operation sould begin. Troubleshooting Problems and remedies CD/MP3 player Abnormal noise is produced. • Check whether a disc that the system cannot play is loaded. Play does not start. • Check whether a disc is loaded. The disc indicator lights when a disc is loaded. • Wipe the disc clean (page 34). • Replace the disc. • Place a disc that this system can play. • Place the disc correctly. • Remove the disc and wipe away the moisture on the disc, then leave the system turned on for a few hours until the moisture evaporates. • Press N to start play. The sound skips. • Wipe the disc clean (page 34). • Replace the disc. • Try moving the system to a place without vibration (e.g., on top of a stable stand). MP3 audio track cannot be played back. • Recording was not performed according to the ISO9660 level 1 or level 2 format, or Joliet in the expansion format. • The MP3 audio track does not have the extension “.MP3”. • The data is not stored in MP3 format. • Discs containing files other than MPEG1, 2, 2.5 Audio Layer-3 files cannot be played. MP3 audio tracks take longer to play back than others. • After the system reads all tracks on the discs, playback may take more time than usual if: – the number of albums or tracks on the disc is very large. – the album and track organization structure is very complex. The album title, track title and ID3 tag do not appear correctly. • Use a disc that conforms with ISO9660 level 1, level 2, or Joliet in the expansion format. • The disc ID3 tag is not ver. 1 or ver. 2. Tuner Severe hum or noise. Stations cannot be received. • Set the proper band and frequency (page 24). • Connect the antenna properly (page 11). • Find a place and an orientation that provide good reception, then set up the antenna again. If you cannot obtain good reception, we recommend you connect a commercially available external antenna. • The supplied FM lead antenna receives signals along its entire length, so make sure you extend it fully. • Locate the antennas as far away from the speaker cords as possible. • Consult your nearest Sony dealer if the supplied AM antenna has come off the plastic stand. • Try turning off surrounding electrical equipment. A stereo FM program cannot be received in stereo. • Press FM MODE until “MONO” disappears. Optional components There is no sound. • Refer to General items “There is no sound.” and check the condition of the system. • Connect the component properly (page 30) while checking: – if the cords are connected properly. – if the cord plugs are firmly inserted all the way. • Turn on the connected component. • Refer to the operating instructions supplied with the connected component and start playing. • Press FUNCTION repeatedly to select “ANALOG IN” (page 30). The sound is distorted. • Set the volume of the connected component lower. If the system still does not operate properly after performing the above measures, reset the system as follows: 1 Disconnect the power cord. 2 Reconnect the power cord. 3 Press ?/1 to turn on the system. 4 Press x, USER PROFILE 5 and POWER, on the system at the same time. The system is reset to the factory settings. You should set the settings you made, such as the preset stations. If a message appears while using the system, follow the procedures below to correct the problem. Network Cannot Play • The track cannot be played in the following cases: – Sampling Rate is other than 32 kHz, 44.1 kHz, 48 kHz. – The track is not being streamed by linear PCM. – The track is other than one channel or two channel. – The track sampling bits are other than 16 bits. – The server status is busy. Check Network • Check that the Ethernet cable between the system and the hub or router is firmly connected. • Check that the hub or router is turned on. IP Conflict • Set the IP addresses of the system and other devices on the network so that there is no duplication (page 20). No album • Register the track as instructed by the operation manual of the connected server. • Follow the procedure below and reconnect to the server. 1. Select “MEDIA SERVERS?” in the network menu (page 19), then press ENTER. 2. Press ./> repeatedly to select the desired media server, then press ENTER. No Server • Start up the server. M-crew Server can be started up by the following method: Right-click the task tray icon, then click “Start Music Service” in the menu. • M-crew Server may not be recognizing the system. Follow the procedure below and check whether M-crew Server is recognizing the system: 1. Click [Start] – [All Programs] – [M-crew Server] – [TOOLS] – [EQUIPMENT LIST] in that order. 2. If the server name is not present in the list that appears in step 1, device registration must be performed. For details, see the Help or Install Manual within M-crew Server. • When setting a firewall other than that provided with the OS, refer to Troubleshooting in the Installation Manual included on the supplied CD-ROM. • Perform the TCP/IP settings correctly for the system and the computer (page 20). Select Server • Follow the procedure below and reconnect to the server. 1. Select “MEDIA SERVERS?” in the network menu (page 19), then press ENTER. 2. Press ./> repeatedly to select the desired media server, then press ENTER. Server Error • Follow the procedure below and reconnect to the server. 1. Select “MEDIA SERVERS?” in the network menu (page 19), then press ENTER. 2. Press ./> repeatedly to select the desired media server, then press ENTER. Server Close • Start up the server. M-crew Server can be started up by the following method: Right-click the task tray icon, then click “Start Music Service” in the menu. • When you want to change the computer’s network settings, restart the server on this system. This message disappears after a short time. WebRadio Error • Register a station that can be played back on M- crew Server. • Connection may be difficult depending on the internet line status. Wait a bit and then perform the operation again. CD/MP3 No Disc • There is no disc in the player. Messages www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 9 HCD-CZ1/NAS-CZ1 • Installation Instrution for M-crew Server ver1.1 (extract) System Requirements The following software and hardware are required in order to be able to run M-crew Server. s A PC/AT compatible that satisfies the performance requirements described below. M-crew Server does not run in an Apple Macintosh environment. – CPU*: Intel Pentium III 600 MHz (1 GHz or more is recommended) or Celeron 600 MHz (1 GHz or more is recommended) or better – RAM: 256 MB or more is recommended – Video board and display driver: Must be capable of XGA (1024 × 768 pixels) display with at least 65,536 colors. – Free hard disk space required for installation: At least 20 MB (includes M-crew Server and the help, etc.) – CD-ROM or DVD drive (for software installation and CD recording) – Available LAN jack: At least one – Sound board s OS: Windows XP Home Edition/Windows XP Professional/Windows XP Media Center Edition 2004/Windows XP Media Center Edition 2005 M-crew Server does not run in a Microsoft Windows 3.1, Windows 95, Windows 98, Windows ME, Windows NT or Windows 2000 Professional environment. When installing, log on as the administrator. s Internet access (for Gracenote access and WEB RADIO) s Display: XGA (1024 × 768 pixels) Must be able to display at least 65,536 colors. s Used Language: English/German/French * Operation is guaranteed only with Intel Pentium and Celeron CPUs. Notes • Operations are not guaranteed for all the recommended computer environments mentioned above. • Operation is not assured in personally constructed PCs or operating systems and an environment upgraded to the other operating systems. • Original brand and home_made personal computers do not apply. Before installing the software Do not connect the system to your computer before the installation is completed! Close down all applications running on the computer before installing the software! Be sure to log on through a user name which belongs to the computer's administrator to install the software. Installing Installing M-crew Server 1 Turn on your computer and allow Windows to load. 2 Insert the supplied CD-ROM into the CD-ROM drive of your computer. The “M-crew Server SETUP” dialog box appears. Note If the dialog box does not open, double-click CD-ROM (Setup.exe) icon. 3 Select the language to be used. 4 Click [M-crew Server setup]. The installation starts. Note If “.Net Framework” is not installed on your computer, “.NET Framework Installer” dialog box appears. Click [Install] to install “.Net Framework 1.1” and follow the displayed instructions. 5 Follow the on-screen messages. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 10 HCD-CZ1/NAS-CZ1 6 After the installation is completed, click [Reboot] to restart your computer. Be sure to restart your computer only after the installation has been completed. After restarting your computer, the “AUTO LINK FOLDER SETUP” window appears. For Windows XP SP2 The “Windows Security Alert” dialog box appears. Click [Unblock] to unblock the program. Check that [Name] is “M-crew Server task tray icon”, then click the [Unblock] button. If you click the [Keep Blocking] button, you will be unable to use M-crew Server (page 20). 7 Click [NEXT]. The contents located on the path set to ON by the checkbox are loaded automatically. When not making this setting, click the [Skip] button. The connection manual appears automatically. For Windows XP SP2 See “Making the ICF Settings” on page 12 when the “ICF Setting” dialog opens. 8 Confirm the optimum connection method, and connect the system to your computer. Notes • When SP2 has not been applied to Windows XP, M-crew Server may not operate properly unless the latest Windows Security Update is applied. In these cases, apply the latest Windows Update (KB885835) or check the contents noted at the following website and take the necessary measures. http://www.sony.net/Products/OpenMG/support/840987/ • The M-crew Server software uses the installed folders, so do not delete, move, or edit any of the installed folders. Managing these folders like general files on Windows Explorer could cause the contents to become unstable or corrupted. • While the installation is still in progress, do not interrupt the operation or take the CD-ROM out of the CD-ROM drive. Doing so may render it impossible to install the software thereafter. Tip The following modules are installed. 1)Refer to the Microsoft home page and other materials for a detailed description of these Microsoft Modules. 2)Refer to www.gracenote.com for a detailed description of CDDB2. 9 Turn on the system. The system is registered automatically on your computer. To register the system on your computer manually, see “Registering the system on your computer manually” on page 14. Microsoft Module1) .Net Framework Version1.1 Microsoft Data Access Components (MDAC) 2.8 (as necessary) Windows MediaFormatSDK9 Runtime OpenMG SDK OpenMG SDK 3.4.01 OpenMG Limited Patch Other related modules CDDB22) CDDB2 Module Music Server Mcrew Music Server Other related modules M-crew Server M-crew Server Other related modules Other Information Starting up M-crew Server Click [Start] – [All Programs] – [M-crew Server] – [M-crew Server] in that order. Or, double-click the M-crew Server icon on the taskbar. Or, right-click the M-crew Server icon on the taskbar, and select “M-crew Server”. Making the ICF Settings When the M-crew Server icon in the taskbar appears as , make the ICF (Internet Connection Firewall) settings. 1 Click [Start] – [All Programs] – [M-crew Server] – [TOOLS] – [ICF Settings] in that order. “ICF SETTINGS” window appears. 2 Click the port with NG status. A dropdown menu with port numbers appears. If “OK” appears for all server status items, there is no need to make the ICF settings. Click [Close] to close the window. 3 Select any different port number. 4 Click [Apply]. “OK” or “NG” appears. 5 Repeat steps 2 to 4 until “OK” appears for all status items. 6 Click [Close]. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 11 HCD-CZ1/NAS-CZ1 Tips • Windows XP and later versions have a simple firewall function as a standard feature. This firewall function is called “ICF”, and lets users limit communications between home networks or small-scale office networks and the internet. When this firewall is enabled, the firewall must be set to allow communication of specific ports and programs in order to perform communication between M-crew Server and this system. These settings are made at the ICF SETTINGS window. However, note that making these settings may expose your computer to illicit access. • When communication is limited by firewall software other than the OS functions, enable the following .exe files. For a detailed description of the setting method, see the operation manual of the firewall software used. – McrewServer.exe – McTaskTray.exe – McService.exe – McFolderWatcher.exe – McrewHttpService.exe – McrewUPnPService.exe Registering the system on your computer manually When the system is connected to your computer after installing the M- crew Server, the system is registered automatically on your computer. Register the system on your computer manually for higher security. 1 Turn on the system. 2 Press NETWORK on the remote repeatedly to switch the function to MUSIC LIBRARY or WEB RADIO. 3 Press NETWORK MENU on the remote. 4 Press . or > on the remote repeatedly until “REGISTRATION?” appears, then press ENTER on the remote. The count down display appears in the display of the system. 5 Click [Start] – [All Programs] – [M-crew Server] – [TOOLS] – [EQUIPMENT LIST] in that order. “M-crew Server EQUIPMENT LIST” dialog box appears on your computer screen. For Windows XP SP2 The “Windows Security Alert” dialog box appears. Check that [Name] is “MCMachineRegist.exe”, then click the [Unblock] button. If you click the [Keep Blocking] button, you will be unable to use M-crew Server (page 20). 6 Set “Equipment selection mode:” to “Manual”, and click [Add] on your computer. The registration starts. “Complete!” appears in the display of the system when the registration is complete. Uninstalling the M-crew Server software Log on through a user name which belongs to the computer’s administrator and follow the procedures below. Refer to the operating instructions of your computer for details on logging on as a user name which belongs to the computer’s administrator. 1 Stop the service from the task tray icon. Right-click the task tray icon, then click [Stop Music Service] in the menu. The task tray icon display becomes dim. 2 Hide the task tray icon. Right-click the task tray icon, then click [Hide task tray icon] in the menu. The task tray icon display disappears. 3 When Windows XP is in Classic View, switch to Category View, then click [Start] – [Control Panel] – [Add or Remove Programs] in that order. 4 Select [M-crew Server], and click [Change/Remove]. 5 Select [Mcrew Music Server], and click [Change/Remove]. 6 Reboot the computer. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 12 HCD-CZ1/NAS-CZ1 Notes • When uninstalling M-crew Server, a command prompt window appears. Command prompt processing may take some time. However, the uninstall work is proceeding during this time, so do not click the [Cancel] button in the “Installsheild” dialog. • “OpenMG Limited Patch ***” and “OpenMG Secure Module ***” may be used by other software (SonicStage, VAIO Media, etc.). If Open MG SDK is not being used, uninstall “OpenMG Limited Patch ***” and “OpenMG Secure Module ***” in the “Add or Remove Programs” window. Troubleshooting Should you encounter a problem while installing or uninstalling M- crew Server, use the following troubleshooting to remedy the problem. If the problem persists after checking all the below items, fill in the following table and then consult your nearest Sony dealer. In case an error message appears, it is recommended that you write it down. Computer • Manufacturer: • Model: • Type: Desktop type / Laptop type Name of operating system: RAM: Hard disk drive (containing M-crew Server and audio data) • Capacity of the drive: • Free space: Installed folder containing M-crew Server (if other than the default folder)1) • Location of the installed folder: 1) If you do not specify the destination, the software is installed at C:\Program Files\Mcrewserver. Version of the software (M-crew Server Ver.1.0)2): 2) To check the M-crew Server software version, right-click in the M-crew Server window and select “About M-crew Server”, or see the version information on the supplied CD-ROM. Error Message (if one appeared): If an externally connected CD-ROM drive is used • Manufacturer: • Model: • Type: CD-ROM / CD-R/RW / DVD-ROM / Other ( ) • Type of connection to the computer: PC card / USB / IEEE1394 / Other ( ) If another device with USB connection is used • Name of the device (or devices): M-crew Server does not start up • Server ports do not open. 1 Click [Start] – [All Programs] – [M-crew Server] – [TOOLS] – [ICF Settings] in that order. “ICF SETTINGS” window appears. 2 Click the port with NG status. A dropdown menu with port numbers appears. 3 Select any different port number. 4 Click [Apply]. “OK” or “NG” appears. 5 Repeat steps 2 to 4 until “OK” appears for all status items. 6 Click [Close]. Installation was not successful • Be sure to close down all applications before installing the software. If you start the installation while other programs are running, a malfunction may occur. This is especially true for programs that require large amounts of system resources, such as virus-check software. • Make sure your computer has enough hard disk drive space. 150 MB of free space or more on the hard disk drive is required. If your computer does not have enough space, the installation may not be possible. • The [Keep Blocking] button was clicked at the “Windows Security Alert” dialog box when using Windows XP SP2. 1 Click [Start] – [Control Panel] in that order. “Control Panel” window appears. 2 When Windows XP is in Category view, switch to Classic view, then click [Network Connections]. 3 Click “Change Window Firewall Settings” on the left edge. “Windows Firewall” dialog appears. 4 Click the [Exceptions] tab. 5 Click [Add Program]. “Add a program” dialog appears. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 13 HCD-CZ1/NAS-CZ1 6 Select “M-crew Server task tray icon” from the “Programs” list, then click the [OK] button. Make sure that the M-crew Server task tray icon appears and is checked in the “Program and service” list in the “Exceptions” tab of the “Windows Firewall” dialog. 7 Click [OK]. • If the installation is still unsuccessful after all that you have done. 1 Click [Start] – [Control Panel] in that order. “Control Panel” window appears. 2 When Windows XP is in Classic View, switch to Category View, then click [Add or Remove Programs]. “Add or Remove Programs” window appears. 3 Select and click “M-crew Server” in the “Currently Installed Programs” list. When “M-crew Server” does not appear in the “Currently Installed Programs” list, click [Change/Remove] and proceed to step 6. 4 Click [Change/Remove]. 5 Follow the on-screen messages and restart your computer. 6 When the computer restarts, installation again. (See “Installing M-crew Server” on page 8.) • If the installation seems to be stopped The installation may take 10 minutes or more depending on your computer or CD-ROM drive. During the installation, watch out for the occurrence of any of the following problems. “No Server” appears on the NAS-CZ1. • The progress bar on the display is not moving. The access lamp has not lit for a few minutes. The installation is progressing normally. Please wait. • M-crew Server may not be recognizing the system. When communication is limited by firewall software other than the OS functions, enable the following .exe files. For a detailed description of the setting method, see the operation manual of the firewall software used. – McrewServer.exe – McTaskTray.exe – McService.exe – McFolderWatcher.exe – McrewHttpService.exe – McrewUPnPService.exe There is no sound from the system • This M-crew Server is not selected by the server selection on the system side. For details, refer to the operating instructions provided with the system. • The server side system registration is not correct. 1 Check the connection between the system and your computer. To check the optimum connection method, click [Start] – [All Programs] – [M-crew Server] – [MANUAL] – [Connection Manual] in that order. 2 Turn on the system. The system is registered automatically on your computer. The server side must also be set when performing system registration manually. See “Registering the system on your computer manually” on page 14. • Make sure the system is properly connected. (Refer to the connection manual. Also check your computer's network settings.) • Check for the M-crew Server task tray icon. Refer to the startup instructions. Also refer to “Task tray icon not present” on page 24. • Make sure the M-crew Server task tray icon is lighting. Refer to the update instructions. Also refer to “Task tray icon darkened” on page 24. • Make sure the system is registered in M-crew Server. Refer to the instructions for confirming registration. • Restart your computer. • Cannot listen to Web Radio Make sure that the computer’s internet access is correct. If using a proxy server, make sure that the proxy server is set correctly in the “PROXY SETTING” dialog box. Task tray icon not present Task tray icon darkened Cannot uninstall M-crew Server • Follow the procedure below to display the icon again. Click [Start] – [All Programs] – [M-crew Server] – [TOOLS] – [M-crew Server task tray icon] in that order. • Uninstall M-crew Server and re-install it. The service is not active. Troubleshoot it by checking the following items. • Right-click the task tray icon. Click [Start Music Service]. • Click [Start] – [All Programs] – [M-crew Server] – [TOOLS] – [ICF Settings] in that order and check the port. • Uninstall M-crew Server and re-install it. 1 Stop the service from the task tray icon. Right-click the task tray icon, then click “Stop Music Service” in the menu. 2 Hide the task tray icon. Right-click the task tray icon, then click [Hide Task Tray icon] in the menu. 3 When Windows XP is in Classic View, switch to Category View, then click [Start] – [Control Panel] – [Add or Remove Programs] in that order. Select the desired program and remove it. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 14 HCD-CZ1/NAS-CZ1 CD MECHANISM DECK (BU-K7BD81B) SERVICE POSITION • In checking the CD mechanism deck (BU-K7BD81B), prepare extension jig (Part No. J-2501-248-A: 1mm Pitch, 27 cores, Length 300mm). CD board (CN201) CD mechanism deck (BU-K7BD81B) MAIN board (CN700) MAIN board (CN603 1pin, 2pin) Connect extension jig (J-2501-248-A) to the CD board (CN201) and MAIN board (CN700). If operating the CD, solder-bridge the MAIN board (CN603 1pin, 2pin). ALL BOARDS SERVICE POSITION • In checking the FL board FRONT PANEL board and MAIN boards, prepare two extension jigs (Part No. J-2501-077-A: 1.25mm Pitch, 13 cores, Length 300mm and Part No. J-2501- 009-A: 1.25mm Pitch, 15 cores, Length 300mm). MAIN board (CN602) MAIN board (CN601) PSAMP board SUBPS board FL board (CN1001) FRONT PANEL board (CN1201) Connect extension jig (J-2501-077-A) to the FL board (CN1001) and MAIN board (CN602). Connect extension jig (J-2501-009-A) to the FRONT PANEL board (CN1201) and MAIN board (CN601). TOP PANEL board ETHER board CD board www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 15 HCD-CZ1/NAS-CZ1 SECTION 2 GENERAL This section is extracted from instruction manual. Main unit Display window 9 FUNCTION 2 NETWORK 5 NETWORK lamp 5 PHONES jack q; Remote sensor 8 USER PROFILE 1 – 5 3 VOL +/– 7 ?/1 (On/Standby) 1 Z PUSH OPEN 4 N (play) 6 x (stop) 6 ALPHABETICAL ORDER A – O P – Z BUTTON DESCRIPTIONS 1 2 3 4 5 q; 6 7 8 9 • Location of controlls www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 16 HCD-CZ1/NAS-CZ1 Remote control ALBUM +/– 9 DISPLAY 2 DSGX qf ENTER 8 FAVORITE ADD q; CALL q; DELETE q; FM MODE qj FUNCTION wd LIBRARY MODE wa SEARCH wa NETWORK qa MENU 7 PRESET EQ 3 REPEAT qj SCROLL qd SLEEP qs TUNER BAND qg TUNER MEMORY 5 TUNING MODE qh TUNING +/– ql USER PROFILE ws VOL +/– 4 ?/1 (On/Standby) 1 1/ALL 6 m/M (rewind/fast forward) qk TCURSOR/CURSORt qk ./> (go back/go forward)* ql N (play)* w; X (pause) w; x (stop) w; * The N and . buttons have tactile dots. Use the tactile dots as a reference when operating the system. ALPHABETICAL ORDER A – M N – Z BUTTON DESCRIPTIONS 1 2 4 3 5 6 7 9 0 8 qa qg qh qj w; wa ws qs qd qf wd ql qk www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 17 HCD-CZ1/NAS-CZ1 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2. SPEAKER GRILL (F/R) ASSY, TOP PANEL ASSY (Page 18) 3-3. COVER BOTTOM ASSY (Page 18) 3-4. REAR PANEL SECTION (Page 19) 3-5. FRONT PANEL SECTION (Page 20) 3-6. TOP PANEL SECTION (Page 20) 3-7. BASE UNIT (BU-K7BD81B) (Page 21) 3-8. MAIN BOARD SECTION (Page 21) 3-9. ETHER BOARD, MAIN BOARD (Page 22) SET www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 18 HCD-CZ1/NAS-CZ1 3-3. COVER BOTTOM ASSY Note: Follow the disassembly procedure in the numerical order given. 3-2. SPEAKER GRILL (F/R) ASSY, TOP PANEL ASSY 1 six bosses 2 speaker grill-F assy 1 six bosses 3 six bosses 3 six bosses 4 speaker grill-R assy 6 top panel assy 5 three screws (BVTP 3 × 8) 5 three screws (BVTP 3 × 8) 5 three screws (BVTP 3 × 8) 5 three screws (BVTP 3 × 8) 1 four screws (BVTP 3 × 6) 1 five screws (BVTP 3 × 6) 2 cover bottom assy www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 19 HCD-CZ1/NAS-CZ1 3-4. REAR PANEL SECTION 2 four screws (BVTP 3 × 8) 3 1 five screws (BVTP 3 × 16) 4 acoustic absorbent 6 rear panel section 4 acoustic absorbent cushion front panel section cushion 5 two speaker terminals (SP201) 5 two speaker terminals (SP101) Note: Be sure to replace the Cushion (Part No. 2-586-851-01) when the Rear Panel section was removed from the Front Panel section. Note: Assemble the Rear Panel, taking care whether the Speaker lead wires are pinched in the panel and the screws. Note: Arrange the wires by putting the Speaker lead wires in the slot of the Front Panel. 1 five screws (BVTP 3 × 16) rear panel speaker lead wires speaker lead wires speaker lead wires FRONT PANEL REAR VIEW front panel front panel slot NOTE WHEN ASSEMBLING THE REAR PANEL www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 20 HCD-CZ1/NAS-CZ1 3-5. FRONT PANEL SECTION 3-6. TOP PANEL SECTION 1 four screws (BVTP 3 × 8) 5 three speaker terminals (SP102, SP103) 2 5 three speaker terminals (SP202, SP203) 3 FFC 13P (CN602) 4 FFC 15P (CN601) 6 front panel section 3 two screws (BVTP 2.6) 3 two screws (BVTP 2.6) 1 FFC 27P (CN201) 2 connector (S601) 4 springFL-R 4 springFL-L 6 spring-F 7 top panel section 5 NOTE WHEN REMOVING THE TOP PANEL www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 21 HCD-CZ1/NAS-CZ1 3-7. BASE UNIT (BU-K7BD81B) 3-8. MAIN BOARD SECTION 9 base unit (BU-K7BD81B) 6 7 four claws 8 CD cover 3 two screws (PTPWH M2.6 × 6) 3 two screws (PTPWH M2.6 × 6) 4 two vibration proof rubbers (green) 5 two vibration proof rubbers (red) 2 difuser 1 three screws (BVTP 2.6) qf four screws (BVTP 3 × 8) qh two screws (BVTP 3 × 6) qg two screws (BVTP 3 × 10) qh screw (BVTP 3 × 6) qs two screws (BTTP M2.6) qh screw (BVTP 3 × 6) 7 two screws (BVTP 3 × 6) q; tuner pack (TM-10CE: AEP, UK models) (TM-10U: US model) 8 9 FFC 9P (US model) FFC11P (AEP, UK models) 6 FFC 15P (CN650) 1 four screws (BVTP 3 × 6) 3 connector (CN5) 2 5 SUBPS board qj MAIN board section qd bracket IC 4 connector (CN603) qa connector (CN600) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 22 HCD-CZ1/NAS-CZ1 3-9. ETHER BOARD, MAIN BOARD 1 two screws (BVTP 3 × 6) 4 two screws (BVTP 3 × 6) 2 connector (CN501) 3 ETHER board 4 two screws (BVTP 3 × 6) 5 MAIN board www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 23 HCD-CZ1/NAS-CZ1 SECTION 4 TEST MODE FORCED RESET * The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1. Press the I/1 button to turn the power on. 2. Press three buttons of I/1 , x and [5] simultaneously. 3. The message “COLD RESET” is displayed on the fluorescent indicator tube momentarily after “See you!” is displayed, then becomes standby states. AMP TEST MODE Procedure: 1. Press the I/1 button to turn the power on 2. Press three buttons of VOL – , N and [2] simultaneously. 3. In this mode, change the display as “MIN” y “21” y “MAX” by pressing the VOL – / VOL + buttons. 4. To release this mode, press the I/1 button to execute the cold reset and becomes standby status. DISPLAY CHECK MODE This mode is used to check the fluorescent indicator tube and LEDs. Procedure: 1. Press the I/1 button to turn the power on. 2. Press three buttons of VOL – , N and [3] simultaneously. 3. When this mode is activated, the fluorescent indicator tube and LEDs are all turned on. 4. In this mode, change the display as follows by pressing the [NETWORK] button. All on t FL all off t FL pattern 1 t FL pattern 2 t LED all off t [1] LED on t [2] LED on t [3] LED on t [4] LED on t [5] LED on t I/1 LED on t [NETWORK] LED on t All on t... 5. To release this mode. press the I/1 button to execute the cold reset and becomes standby status. KEY CHECK MODE Procedure: 1. Press the I/1 button to turn the power on. 2. Press three buttons of VOL – , N and [4] simultaneously. 3. If this mode is activated, “KEY-00/12” is displayed on the fluorescent indicator tube. 4. In this mode, each time any key is pressed, it increment the number of display until “KEY-12/12” 5. To release this mode, press three buttons of VOL – , N and [4] simultaneously again. CHANGE-OVER THE AM TUNING INTERVAL (EXCEPT AEP, UK models) The AM tuning interval can be changed over 9kHz or 10kHz Procedure: 1. Press the I/1 button to turn the power on. 2. Press the [FUNCTION] button to select “AM”. 3. Press the I/1 button again to turn the power off (standby). 4. While pressing the [FUNCTION] button, press the I/1 button. 5. It turns power on and display “STEP 9kHz” or “STEP 10kHz”, and thus the tuning interval is changed over. VERSION CHECK MODE * This mode is used to check the version of model, destination and software. Procedure: 1. Press the I/1 button to turn the power on. 2. Press three buttons of VOL + , [NETWORK] and [1] simultaneously. 3. when this mode is activated, model and destination is displayed on the fluorescent indicator tube. 4. In this mode, change the version display as model/destination t CD-STR t Ethernet system t model/destination t ... 5. To release this mode, press the I/1 button to execute the cold reset and becomes standby status. CD ERROR HISTORY DISPLAY MODE * This mode can be used for error code display of CD section. Procedure: 1. Press the I/1 button to turn the power on. 2. Press the [FUNCTION] button to select “CD”. 3. Press three buttons of VOL + , N and [3] simultaneously. 4. When this mode is activated, it displays as follows. Error count display: Em 0Ed## Em0 : Not used Ed## : Error count of BD section 5. In this mode, change the display as error count y “MO” display (not used) y error detail by pressing the [ALBUM -]/ [ALBUM +] keys on remote commander (RM-ANP002). 6. In the error detail display mode, change the error number and that error detail by pressing the . or > keys on remote commander (RM-ANP002). Error detail display: 0*********** * : Hexadecimal number (refer to following table for detail) 7. To release this mode, press the I/1 button to turn the power off or press the [FUNCTION] button to change the function. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 24 HCD-CZ1/NAS-CZ1 Digit Contents Value Detail 1st Error number 0 to 9 “0” is latest error 01 Focus error 02 GFS error 03 Time out of wake up 2nd and 3rd Kind of error 04 Defocused continuously 05 Q code error 06 Can not tracking on 07 Blank disc 01 Shipping 02 Power off in progress 03 Power on in progress 04 Initializing 05 Oscillation stop status 06 Starting up the oscillation 4th and 5th Process when an 07 Stop status error occurred 08 Stopping in progress 09 Starting up in progress 0a TOC reading 0b Searching 0c Playback in progress 0d Pause in progress 0e Playback manual searching 0f Pause manual searching Step number 6th and 7th when an error XX Step number occurred 01 Normal speed 8th and 9th 02 Double speed 04 4 times speed 10th an 11th Not used 00 Fixed at “00” Error detail: Disc speed when an error occurred CD SERVICE MODE 1. Press the I/1 button to turn the power on. 2. Press the [FUNCTION] button to select “CD”. 3. Press three buttons of [VOL +], N and [1] simultaneously. 4. If this mode is activated, “SERVICE MODE” is displayed on the fluorescent indicator tube. (Goes off that display when release three buttons) 5. In this mode, it operation as following table. *1) Use the remote commander (RM-ANP002) 6. To release this mode, press the I/1 button to turn the power off. Buttons Display Operation . *1 SLED OUT Move the sled to outer side > *1 SLED IN Move the sled to inner side N LD ON or LD OF Laser diode on / off CD SERVO TEST MODE 1. Press the I/1 button to turn the power on. 2. Press the [FUNCTION] button to select “CD” 3. Press three buttons of VOL + , N and 2 simultaneously. 4. In this mode, it the display changes as follows (Servo test menu mode) by pressing the . or > keys on remote commander (RM-ANP002). 5. To release this mode, press the I/1 button to turn the power off. Servo test menu: 1. bdt S CURVE mode * This mode is use the S-curve check. 1. In the servo test menu mode, press the . or > keys on remote commander (RM-ANP002) to select “”. 2. Press the [ENTER] key to enter the S-curve mode. 3. To back to the servo test menu mode, press the x key on remote commander (RM-ANP002) 2. bdt RAM READ made 1. In the servo test menu mode, press the . or > keys on remote commander (RM-ANP002) to select “”. 2. Press the [ENTER] key to enter the RAM read mode. 3. In this mode, the display cyclic changes as follow by pressing the [ALBUM -] or [ALBUM+] key. r bdt S CURVE r bdt RAM READ r bdt RAM WRITE r bdt COMOUT r bdt ERR RATE Display Item DISC SIZE 00:no disc, 01:8cm disc,02:12cm disc RFDoffset RFDC offset value RFAoffset RFAC offset value FE offset FE offset value TE offset TE offset value RF gain_2 RF AMP secondly gain value TE gain_2 TE secondly gain value EFBALgain EF balance gain value EQ BOOT EQ boot setting value 4. To back to the servo test menu mode, press the x key on remote commander (RM-ANP002) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 25 HCD-CZ1/NAS-CZ1 3. bdt RAM WRITE mode Not used in servicing 4. bdt COMOUT mode Not used in servicing 5. bdt ERR RATE mode In bdt ERR RATE mode, N , . and > keys on the main unit don't work as its normally key function. 1. Press the I/1 button to turn the power on. 2. Insert a CD disc and press the [FUNCTION] button to select “CD”. 3. Press the N key and select any track with the . / > keys to play a sample track. Press the [REPEAT] key on remote commander to set REPEAT 1 mode if you need. 4. Press three buttons of N , [VOL+] and [2] simultaneously. 5. Change the display by pressing the . / > keys to show “bdt ERR RATE”. 6. Press the [ENTER] key on remote commander (RM-ANP002). 7. It displays the error rate as follows. Error rate display: ****####$$&&%% **** : C1 error rate #### : C2 error rate $$ : Track number && : Minutes %% : Seconds Note: If “C2” value is not “0000” while playing a track, there is a possibility that sound skipping happens. By comparing the playability of a track, you can check the disc condition. To back to the servo test menu mode, press the x key on remote commander. To release the servo test mode, press the I/1 button to turn the power off. Ver. 1.1 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 26 HCD-CZ1/NAS-CZ1 Note: 1. CD Block is basically constructed to operate without adjustment. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10 MΩ impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. 5. Check the focus bias check when optical block is replaced. FOCUS BIAS CHECK Procedure : 1. Connect the oscilloscope to TP (RFACO) and TP (VC) on the CD board. 2. Insert the disc (YEDS-18). (Part No. : 3-702-101-01) 3. Press the CD u button. 4. Confirm that the oscilloscope waveform is as shown in the figure below. (eye pattern) A good eye pattern means that the diamond shape (◊) in the center of the waveform can be clearly distinguished. • RF signal reference waveform (eye pattern) CD SECTION SECTION 5 ELECTRICAL ADJUSTMENTS + – CD board TP (RFACO) TP (VC) oscilloscope (DC range) Checking Location: VOLT/DIV: 0.2 V (with the 10: 1 probe in use.) TIME/DIV: 500 ns 1.1 When observing the eye pattern, set the oscilloscope for AC range and raise vertical sensitivity. 0.2 Vp-p TP (RFACO) TP (VC) – CD BOARD (Conductor Side) – www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 27 27 HCD-CZ1/NAS-CZ1 SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM – SERVO SECTION – MIACK 8 PO11/BUCK/AD14 36 MILP 5 RESET 2 MICS 4 MIDIO 6 MICK 7 MP3 DECODER IC301 A/D CONVERTER CH2OUTF CH2OUTR 23 24 21 4 5 6 7 17 18 16 15 RFACI ASYO ASYI FILTER FILO PCO CLTV FILI DIGITAL PLL ASYMMETRY CORRECTOR EFM DEMODULATOR CD DSP IC101 (1/2) MDP DIGITAL CLV PROCESSOR 32K RAM ERROR CORRECTOR INTERNAL BUS SQCK SQSO EXCK AOUT1 C4M XTSL XTAO XTAI AOUT2 R-CH D/A DIGITAL INTERFACE D/A CONVERTER SELECTOR CLOCK GENERATOR SUBCODE PROCESSOR SCOR WFCK XUGF GFS EMPH SENS DATA CLOCK XLAT SBSO I-SENS O-DATA O-XLT TEI FEI FOCUS/ TRACKING/SLED SERVO DSP FOCUS/TRACKING/SLED PWM GENERATOR SFDR CH3FIN CH4IN CH3RIN CH3OUTF CH3OUTR CH1FIN CH1RIN CH2FIN CH2RIN 20 MUTE SRDR TFDR TRDR FFDR FRDR SSTP COUT MIRR, DFCT, FOK DETECTOR SERVO AUTO SEQUENCER SERVO INTERFACE CPU INTERFACE SCLK TO CPU INTERFACE FOK MIRR DFCT 2 OPIN+ CH4OUTF CH4OUTR 27 OPOUT M101 (SPINDLE) MOTOR DRIVE MOTOR DRIVE COIL DRIVE CH1OUTF CH1OUTR COIL DRIVE M M M102 (SLED) MOTOR/COIL DRIVE IC251 2-AXIS DEVICE (TRACKING) (FOCUS) CD DSP IC101 (2/2) • SIGNAL PATH : CD PLAY 14 13 11 12 I-SCOR A (Page 29) CD-L 13 11 12 9 10 14 119 108 21 23 3 1 2 7 TO SERVO AUTO SEQUENCER 42 51 53 XPCK 112 50 52 45 46 6 XRST 100 O-XRST 73 96 97 81 78 117 93 77 86 98 99 115 107 102105104 110111113 68 53 O-CLOCK 54 69 LRCK BCK PCMD LRCKIA SDI0 63 66 65 16 BCKIA 15 SFSY/LRCKIB 19 SBSY/BCKIB 18 14 LRCKI BCKI PCMDI SDO0 62 60 61 11 52 58 26 27 28 29 24 22 20 19 37 36 E B A D +3.3V F DETECTOR A B C D RF SUMMING AMP FOCUS ERROR AMP TRACKING ERROR AMP RFACO FEO TEO E F AUTOMATIC POWER CONTROL Q10 APC LD AMP LD LD PD LASER DIODE OPTICAL PICK-UP BLOCK (KSM-213EDP) PD I-V AMP D C EQ_ IN 41 35 34 EQ AC_ SUM RFAC VCA X171 16.9344MHz SYSTEM CONTROLLER IC601 (1/3) S101 (LIMIT) I-MP3DATA 55 O-MP3DATA 56 O-MP3CLK 57 O-MICS 85 I-MP3_ACK 83 I-MP3_REQ 82 O-MILP 84 O-MP3RST 86 O-XTCN 70 CD_OPEN_CLOSE 75 STANDBY 3 I-MP3_STBY 81 • R-ch is omitted due to same as L-ch. XTACN 95 DISC LID OPEN DETECT S601 w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 28 28 HCD-CZ1/NAS-CZ1 6-2. BLOCK DIAGRAM – ETHERNET SECTION – 79 78 77 76 17 18 TXD0 DOUT VOUTL E-LOUT R-CH PDOWN NRESET IICDATA IICCLK VOUTR DIN BCKIN MCLK LRCK MUTEB SDIDEM TXD1 TXD2 TXD3 80 TXEN_N 82 TXCLK_N 83 TXER_N 75 COL_N 74 CRS_N 89 RXD0 91 RXD1 92 RXD2 93 RXD3 87 68 RXDV_N 86 RXCLK_N 84 RXER_N 94 MDC 95 MDIO 2 PIOC1 RAS MD0-15 MD0-15 MA1-19 MA1-19 MA1-12 CAS LDQM UDQM CLK CKE WE CS RAS CAS LDQM UDQM CLK CKE WE CS OE 3 PIOC2 17 18 19 20 TXD0 TXD1 TXD2 TXD3 16 TXEN 15 TXC/REF_CLK 14 TXER 21 COL/RMII 22 CRS/RMII_LPBK NC RXD– RXD+ TXD– TXD+ NC 6 RXD0/PHYAD4 5 RXD1/PHYAD3 4 RXD2/PHYAD2 3 RXD3/PHYAD1 9 RXDV/PCS_LPBK 10 RXC 11 46 45 RXER/ISO 2 MDC 1 MDIO 30 PD# 48 RST# 108 BCLK 109 MCLK 110 LRCK 107 PIOC7 127 PIOC0 1 2 3 4 11 8 1 PIOC8 XRASN XA1-19 XD0-15 67 XCASN 73 XDQM0 72 XDQM1 69 XSDCLK 71 XSDCKE 58 XWEN 70 XSDCSN 57 XOEN 17 RAS A0-11 A0-15 DQ0-15 DQ0-15 16 CAS 14 LDQM 77 ETHER-PDOWN 37 I2C_DATA 38 I2C_CLK 76 ETHER-NRESET 36 UDQM 35 CLK 34 CKE 15 WE 18 CS FLASH MEMORY IC504 SD-RAM IC503 SYSTEM CONTROLLER IC601(2/3) ETHERNET CONTROLLER IC502 D/A CONVERTER IC505 ETHERNET INTERFACE IC501 +2.5V REGULATOR IC506 PULSE TRANSFORMER T501 11 WE 28 OE 12 RST RESETN 128 114 115 124 125 PIOC4/SDA/SDI1 102 PIOC5/SCL/SCLK1 101 122 8-14,16,26, 25,23-20, 18,17 53-56,42-37, 50,48,47,45, 44,27,29,30,35 2,3,5,6,8,9, 11,12,39,40,42, 43,45,46,48,49 21-24, 27-32, 20,19 29-36, 38-45 24-16, 8-1 X502 24.576MHz OSC1N OSC1 X501 25MHz XI XO 41 TX+ 38 VDDRCV (2.5V SUPPLY) 40 TX– X503 11.2896MHz OSC0N +2.5V EVER+3.3V OSC0 33 RX+ 32 RX– 1 2 6 3 4, 5 7, 8 1 16 J501 (ETHERNET) 14 15 11 9 10 2 3 6 7 8 • SIGNAL PATH : ETHERNET B (Page 29) • R-ch is omitted due to same as L-ch. w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 29 29 HCD-CZ1/NAS-CZ1 6-3. BLOCK DIAGRAM – MAIN SECTION – IC603 VOLTAGE DETECT IC602 5 4 +3.8V REGULATOR IC604 SUB POWER TRANSFORMER T2 MAIN POWER TRANSFORMER T1 6 16 8 3 J201 R-CH R-CH CD-L E-LOUT SURROUND OR DPL BUFF MCU I/F L-CH TU-L TU-R R-CH TUNED DI DO CK CE RDS DATA SIRCS FL DRIVER IC1001 SYSTEM CONTROLLER IC601(3/3) INPUT SELECT, ELECTRICAL VOLUME IC701 POWER AMP IC201 FM/AM TUNER PACK FLUORESCENT INDICATOR TUBE FL1001 RDS CLK TUNED DI DO CK CE RDS DATA RDS CLK TUNED PLL-DI PLL-DO PLL-CLK PLL-CE RDS_DATA RDS_CLK O-AMTE LED7 DI TUNED DO CK CE RDS DATA RDS CLK ANALOG IN R-CH 3 14 15 4 5 68 RM_INT SELF_PROG 21 28 FLASHO 10 19 FL_DATA 27 FL_CLK 29 FL_CS 30 FL_RESET SDATA DIG0 1G 2G-16G P1-35 SCK CS RST 31 39 8 4 5 7 6 5 63 64 62 65 61 60 87 GEQ_CLK 45 GEQ_DATA 46 HP_IN 32 SPK_RELAY +INA OUTA 41 AMP_STBY 34 AMP_MUTING 33 LINE_MUTE 44 22 21 MUTING Q761 MUTING SWITCH Q607 MUTING Q731,831 MUTE CONTROL Q860,862 OVER LOAD DETECT Q261,262 RELAY DRIVER Q263 BUFFER Q601,602 MODE CONTROL Q603,604 LED DRIVE Q1272 RELAY DRIVE Q1 LED DRIVE Q1201-1205 RESET SWITCH Q605, 606 GRID DRIVE Q1001 NETWORK D1271 FM 75Ω COAXIAL REMOTE CONTROL RECEIVER IC1011 AM -1 13 1 +INB R-CH RY201 J202 OUTB 51-25, 23-16 3-1, 64-53 21-55 20-6 STBY_LED RESET 8 KEY2 98 16 AC.CUT 23 MUTEA 6 MUTEB 11 STANDBYA 9 STANDBYB 14 KEY1 99 KEY0 100 KEY_INT LED1 LED5 POWER_RELAY +3.3V VF2 VF1 FL–30V D651 D650 D135 ETHER+4V ETHER+3.3V D+4V MP3+1.5V A+3.3V CD AVDD CD DVDD A+9V AMP B- TO POWER AMP AMP B+ M+7V B-UP+3.3V EVER4V D606 D605 RECT D613 RY1 F1 (AC IN) D607 D608 20 42 X2 15 X1 14 I/1 D1251 D1201-1205 (PROFILE) FRONT PANEL KEYS S1201-1205,1251, S1252,1256,1257, S1261,1263,1271 97 | 93 | + SP203 (WOOFER) SP103 (WOOFER) SP202 (FRONT TWEETER) SP102 (FRONT TWEETER) SP201 (BACK TWEETER) L-CH SP101 (BACK TWEETER) PHONES –30V REGULATOR Q131 RECT D131-134 +4V REGULATOR IC114 +4V REGULATOR IC113 +7V REGULATOR IC112 +9V REGULATOR IC111 +3.3V REGULATOR IC650 +1.5V REGULATOR IC303 F101 F102 RECT D111-114 RECT D101 X600 5MHz • SIGNAL PATH : CD PLAY : TUNER : AUX IN : ETHERNET • R-ch is omitted due to same as L-ch. A (Page 27) (Page 28) B (AEP, UK) (AEP, UK) MUTE SWITCH Q600 R-CH w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 30 30 HCD-CZ1/NAS-CZ1 • Note for Printed Wiring Boards and Schematic Diagrams • Indication of transistor C B These are omitted. E Q • Circuit Boards Location Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • f : internal component. • 2 : nonflammable resistor. • 5 : fusible resistor. • C : panel designation. • A : B+ Line. • B : B– Line. • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. – CD Board – no mark : CD PLAY – Other Section – no mark : TUNER ( ) : CD PLAY 〈〈 〉〉 : TAPE PLAY { } : REC • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal produc- tion tolerances. • Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal produc- tion tolerances. • Circled numbers refer to waveforms. • Signal path. F : TUNER J : CD PLAY f : AUX IN d : ETHERNET Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • f : internal component. • : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: Parts on the pattern face side seen from (Conductor Side) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Component Side) the parts face are indicated. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Caution: Pattern face side: Parts on the pattern face side seen from (Side B) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Side A) the parts face are indicated. B These are omitted. C E Q TOP PANEL board FRONT PANEL board FL board TUNER UNIT PSAMP board SUBPS board MAIN board ETHER board CD board w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 31 31 HCD-CZ1/NAS-CZ1 6-4. PRINTED WIRING BOARD – CD BOARD – • See page 30 for Circuit Boards Location. : Uses unleaded solder. C10 C260 C14 C15 C16 C18 C11 R405 C316 R354 R353 R352 R351 R302 R253 C315 R191 R172 R171 R162 R313 X171 R121 R12 R11 R10 Q10 C116 C312 C184 C183 C303 C302 C305 C259 C258 C257 C255 C203 C196 C195 C201 C182 C171 C172 C308 C151 C134 C125 C123 R165 R13 C17 FB301 C318 R201 C174 R173 R205 C209 C210 C314 M102 S101 M101 IC251 IC101 CN101 CN201 R419 R412 R411 R410 R409 R408 R407 R406 R404 R403 R402 R401 R305 R303 R301 R252 R251 R182 R181 R163 R151 R143 R142 R141 R133 R132 R131 R114 R113 R112 R111 R307 C311 C310 C309 C307 C306 C252 C251 C194 C181 C320 C163 C162 C143 C142 C141 C133 C132 C131 C124 C111 C122 C115 C114 C113 C112 C185 C186 R306 IC303 C317 R203 R161 C161 C211 C212 R204 C213 IC301 C313 M E (COMPONENT SIDE) CD BOARD 1-861-619- 21 (21) 30 31 60 120 91 1 61 90 (CONDUCTOR SIDE) CD BOARD 1-861-619- 21 (21) (SPINDLE) M (SLED) 1 3 5 4 1 16 17 32 64 49 48 33 (LIMIT) 1 27 A MAIN BOARD CN700 (Page 36) TP (RFACO) OPTICAL PICK-UP BLOCK (KSM-213EDP) TP (VC) 1 7 14 8 28 22 15 21 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 A B C D E F G H I R167 R166 w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 32 32 HCD-CZ1/NAS-CZ1 6-5. SCHEMATIC DIAGRAM – CD BOARD – R406 R407 R408 R409 R411 R412 R410 C151 R203 C141 R143 R142 R141 C133 R133 R132 R131 C134 TP125 TP124 C125 R121 C15 C122 C123 C132 C142 R151 C111 C113 C112 C114 R111 TP429 TP428 TP430 TP431 C115 C195 TP432 IC101 C163 R163 C196 R162 C210 C194 R253 TP418 JPO004 C251 R252 R251 C16 R12 JPO10 R11 C17 C18 R10 TP10 TP11 TP12 TP13 TP14 TP15 TP16 TP17 TP18 TP19 C182 C201 C181 C258 C257 C252 C255 C260 R181 R182 C183 C184 C203 C162 C161 R161 R352 TP427 TP103 TP104 TP105 C209 TP436 TP420 TP421 C186 C185 R191 TP251 TP252 TP253 TP250 C306 R405 R404 R419 R403 R402 R401 R302 C317 R305 R301 C316 C315 R313 C307 C302 C303 C305 TP422 C312 C313 C314 C311 C309 C308 R303 C310 R353 R354 C11 C10 C14 C116 C318 R307 R351 TP433 TP187 TP401 TP409 TP411 TP410 TP434 TP419 TP412 TP413 TP414 TP415 TP416 TP417 TP408 TP407 TP406 TP405 TP404 TP403 TP402 TP186 R205 C320 C213 C212 C211 TP435 CN101 TP423 IC301 R173 C143 C171 R171 R172 R165 TP425 TP426 S101 C259 IC251 M102 M101 R201 R204 CN201 FB301 IC303 TP102 R306 R113 JPO102 JPO103 R13 TP424 R112 R114 TP177 C124 C172 C131 C174 X171 Q10 R166 R167 100 100 100 100 100 100 100 100 10V 0 0.1 3.3k 1k 4.7k 0.01 180k 10k 1M 0.1 RFACI RFACO 0.1 15k 0.1 0.1 0.1 0.47 1500p 0 3300p 3300p 470p 470p 1k FFDR FRDR TRDR TFDR 0.1 0.1 MDP CXD3059AR 0.1 100 0.1 47k 0.1 0.1 10k GAIN_SW MDP 6800p 22k 10k 1 100k APC 0 220 4V 1000p 3.3 E D A B C PD F+ F- T- F- 0.1 100 10V 0.1 0.1 0.1 0.1 0.1 220 10V 100 100 22 6.3V 22 6.3V 100 10V 0.1 0.1 100 100 PCMDI LRCK PCMD BCK 0.01 AVDD AGND DGND 470p 470p 0 SP+ SL+ SL- SP- 0.1 100 100 100 100 100 100 10k 0.01 100k 100k 0.0022 0.1 220 0.1 0.1 0.1 220 4V MP3GND 0.1 0.1 47 4V 0.1 0.1 47 4V 100k 0.1 100 100 10 10 0.1 100 10V 0.01 10k 100 MP3VDD MGND MP3STB DOUT LOUT ROUT AVDD XTCN XRST DATA XLT CLK SENS SCOR MP3RST MICS MILP MIDIO MICK MIACK MP3REQ MVDD 0 0 22p 22p 220p DVDD 16P IOP1 TC94A34FG-002 0 0.1 22p 470 1M 0 SW+ SW- 0.1 BA5947FM 27P BH15FB1WG F 0 1k FEI TEI 1 IOP2 15k 15k VC 330p 27p 100p 0.1 16.9344MHz 2SA2119K 1k 100 E F F E D A B C MIACK MICK MIDIO MILP MICS SCOR SENS CLOCK DATA XRST XLT CLOCK SENS SCOR XRST MP3REQ DATA MP3STB XTACN XTACN MP3STB D C B A MP3RST XLT MP3REQ MIACK MICK MIDIO MILP MICS MP3RST MDP SFDR SFDR SRDR SRDR FRDR FRDR FFDR FFDR TFDR TFDR TRDR TRDR F+ F+ T+ T+ T- T- F- F- MDP DOUT DOUT AOUT1 AOUT2 AOUT1 AOUT2 VC VCC PD LD T- F- T+ F+ VR AGND F C B A E D OPIN- OPIN+ SW CH1FIN CH1RIN CH2FIN CH2RIN GND CNF4 POWVCC CH2OUTR CH2OUTF CH1OUTR CH4OUTR CH4OUTF CH3OUTF CH3OUTR POWVCC MUTE GND CH3RIN CH3FIN CH4IN CH4CAPA OUTVREF OPOUT PREVCC MIRR NC DFCT FOK VSS LOCK MDP SSTP IOVSS1 SFDR SRDR TFDR TRDR FFDR FRDR IOVDD1 AVDD0 AVSS0 NC E F TEI TEO FEI FEO VC A B C D NC AVDD4 RFDCO PDSENS AC_SUM EG_IN LD PD RFC AVSS4 RFACO RFACI AVDD3 BIAS ASYI ASYO NC VPCO VCTL AVSS3 CLTV FILO FILI PCO AVDD5 DDVROUT DDVRSEN AVSS5 DDCR NC BCKI LRCKI LRCK VSS PCMD BCK VDD EMPH EMPHI IOVDD2 DOUT TEST TEST1 IOVSS2 NC XVSS XTAO XTAI XVDD AVDD1 AOUT1 VREFL AVSS1 AVSS2 VREFR AOUT2 AVDD2 NC IOVDD0 RMUT LMUT NC XTSL IOVSS0 XTACN SQSO SQCK SBSO EXCK XRST SYSM DATA VSS XLAT CLOCK VDD SENS SCLK ATSK WFCK XUGF XPCK GFS C2PO SCOR VDD C4M WDCK COUT PCMDI VIN GND STBY NC VOUT LOUT AGND ROUT MP3RST DOUT MGND MP3GND MILP MICS MP3REQ MIACK MIDIO MICK MP3STB MP3(3.3V) DVDD(3.3V) AVDD(3.3V) MGND DGND XTCN SCOR SENS XLT DATA XRST CLK M+7V SBSY/BCKIB SFSY/LRCKIB TXO VDD CKI/CLOCK/ IRQ/FIO VSS PIO0/SDI2/IO0 PIO1/SDI3/IO1 PIO2/IO2 PIO3/IO3 PIO4/FI1/BUS0/IO4 PIO5/FI2/BUS1/IO5 PIO6/FI3/BUS2/IO7 PIO7/BUS3/IO7 AD4/PO04 AD3/PO03 AD2/PO02 AD1/PO01 AD0/PO00 VSS VDD CKO/PO13/AD16 VDDX XO XI VSSX TEST MIMD VSSP VCOI VDDP RESET STANBY MICS MILP MIDIO MICK MIACK VDDT VSS BCKO LRCKO SDO0 SDI0 BCKIA LRCKIA DATA SDI1/ SDO2 CS/RAS/ AD15/CAS/ PO12 SDO3/OE PO11/BUCK/AD14 PO10/CCE/AD13 PO9/AD12 PO08/AD11 SRMSTB VDDT AD10 AD9 AD8 PO07/AD7 PO06/AD6 AD5/ PO05 VDDM WE/SDO1 AUTOMATIC CD DSP (LIMIT) MOTOR/COIL (SPINDLE) (SLED) +1.5V REGULATOR MP3 DECODER CONTROL POWER DRIVE CH1OUTF (Page 37) • See page 45 for Waveforms. • See page 46, 47, 48 for IC Block Diagrams. w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 33 33 HCD-CZ1/NAS-CZ1 IC504 R532 R503 R508 R501 R507 R506 R502 R504 C501 C512 C513 R505 C517 R542 C516 C511 C521 C524 C525 C519 C548 C544 C508 C510 R514 R546 C507 C509 C563 C569 C566 IC506 C551 C552 C558 C565 C564 C567 C568 R521 R517 C535 C536 C538 C539 C543 C549 C556 D504 D503 C527 C528 C529 R518 R533 C546 C533 C530 C532 C531 R519 C504 C505 C520 C515 R516 R515 C523 C503 R529 R530 R572 C545 R573 R574 D511 R531 R545 D512 D513 D514 R551 R552 R553 R554 R571 C514 X503 X502 X501 FB502 FB503 C522 FB504 FB505 FB511 C559 FB508 FB510 FB518 EP501 IC503 IC501 D502 IC505 R526 R509 R510 R511 R512 R513 R527 D501 R561 C553 C550 C518 C557 R522 R525 R541 C540 R528 C542 C547 C534 C555 R559 R534 C537 C541 D505 R524 R523 FB506 R537 FB513 R548 FB509 C554 FB507 R538 R539 FB517 FB515 FB516 D506 FB512 IC502 FB519 FB520 FB521 R540 ETHER BOARD (SIDE B) 1 24 48 25 J501 (ETHERNET) 1-866-454- 11 (11) (CHASSIS) A K A/K A K A/K A K A/K A K A/K 3 1 1 50 25 26 33 64 128 97 11 20 10 1 96 65 24 13 37 36 25 T501 PULSE TRANSCEIVER 1 12 48 1 32 1-866-454- 11 (11) ETHER BOARD (SIDE A) CN501 15 1 MAIN BOARD CN651 (Page 36) B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 A B C D E F G 6-6. PRINTED WIRING BOARD – ETHER BOARD – • See page 30 for Circuit Boards Location. : Uses unleaded solder. Ref. No. Location Ref. No. Location D501 B-4 D502 B-4 D503 B-9 D504 B-9 D505 B-4 D506 B-4 D511 F-12 D512 F-12 D513 E-12 • Semiconductor Location D514 E-12 IC501 E-5 IC502 D-5 IC503 C-3 IC504 C-14 IC505 D-7 IC506 C-11 w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 34 34 HCD-CZ1/NAS-CZ1 6-7. SCHEMATIC DIAGRAM – ETHER BOARD – R571 R572 D505 C559 R519 C556 FB510 FB508 C558 C553 C554 C555 C550 C551 C552 C546 C548 C549 TP511 TP512 TP513 TP514 TP515 TP516 C527 R529 R559 R561 C544 D502 D501 FB515 FB516 CN501 FB517 FB518 FB519 FB520 FB521 R541 R540 C567 C568 C569 R531 R542 C564 C563 IC505 TP531 R525 R523 R522 R524 R521 C566 C565 C562 D504 D503 C572 FB505 FB511 FB509 C530 C531 C510 C509 C508 C507 C571 C543 C542 C547 R528 C537 C540 R539 R538 IC506 C532 C533 X503 C539 C538 R532 R518 C541 TP517 TP518 TP519 TP520 TP521 TP522 TP523 TP524 TP525 R545 R546 R526 R527 C534 R548 FB513 FB512 FB507 FB506 C557 R533 R517 X502 FB504 R516 R515 C521 FB503 C524 C523 C522 C528 C529 C525 C517 R510 FB502 R509 C516 X501 C513 C512 C511 R513 C520 R512 R514 TP501 TP503 C515 R534 R511 C519 D514 D513 D512 D511 R503 R504 R502 R501 R507 R508 R505 R506 C503 C501 C504 C518 R573 R574 TP502 C514 TP509 TP508 TP507 TP506 TP505 TP504 C545 EP501 IC501 IC502 C505 J501 T501 R554 R551 R553 R552 IC503 IC504 D506 R537 C535 C536 75 75 1SS355 0.1 10k 10 16V 0 0 47 6.3V 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 10k R530 100 47 47 0.1 1SS355 1SS355 15P 100 100 0.1 0.1 10 16V 0 10 0.1 10 16V WM8728 100 100 100 100 0 0.1 10 16V 0.1 1SS355 1SS355 0.1 0 0 0.1 10 16V 0.1 100 6.3V 0.1 100 6.3V 0.1 47 6.3V 0.1 0.001 10k 0.1 0.1 100 100 BA25BC0FP-E2 0.1 100 6.3V 11.2896MHz 18p 18p 1k 1M 0.1 4.7k 4.7k 47 47 0.1 10k 0.1 560 1M 24.576MHz 0 10k 10k 0.1 0 10 16V 0.1 100 6.3V 0.1 0.1 0.1 10 16V 10k 0 680 0.1 25MHz 10p 10p 0.1 10k 0.1 10k 10k 100 6.3V 13k 13k 0.1 DAN217-T14 DAN217 -T14 DAN217 -T14 DAN217 -T14 100 100 100 100 100 100 100 100 0.1 0.1 0.1 0.1 75 75 0.001 2kV 0.1 KSZ8721BL ML7201 100 6.3V 8P H1260 0 0 10k 10k MSM56V16160F-8TK -FM1 MBM29LV800BA-70P 1SS355 1k 10p 10p MD0 MD1 MD2 MD3 MD4 MD5 MD6 MD7 MD8 MD9 MD10 MD11 MD12 MD13 MD14 MD15 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 MA11 MA12 MA13 MA14 MA15 MA16 MA17 MA18 MA19 ROMCS WE OE MA1 MA17 MD0 MD1 MD2 MD3 MD4 MD5 MD6 MD7 MD8 MD9 MD10 MD11 MD12 MD13 MD14 MD15 ROMCS OE MA2 MA3 MA4 MA5 MA6 MA7 MA8 WE MA9 MA10 MA11 MA12 MA13 MA14 MD0 MD1 MD2 MD3 MD4 MD5 MD6 MD7 MD8 MD9 MD10 MD11 MD12 MD13 MD14 MD15 WE MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 MA10 MA11 MA12 MA19 MA18 MA16 MA15 VDD VDD VSS VSS DQ0 DQ1 VSSQ DQ2 DQ3 VDDQ DQ4 DQ5 VSSQ DQ6 DQ7 VDDQ LDQM WE CAS RAS CS A10/AP A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 NC CKE CLK UDQM NC/RFU DQ8 DQ9 VSSQ DQ10 DQ11 VDDQ DQ12 DQ13 VSSQ DQ14 DQ15 A11-BA VDDQ (CHASSIS) (CHASSIS) TXD+ TXD- RXD+ NC NC RXD- NC NC LED1+ LED1- LED2+ LED2- CHASSIS_GND TD+ TCT TD- NC NC RD+ RCT RD- TX+ CMT TX- NC NC RX+ CT RX- ETHER-GND D-GND D-GND IICCLK IICDATA PDOWN NRESET D-GND A3.3V A-GND LOUT DA-GND ROUT DA-GND LATI2S SCKDSD SDIDEM MUTEB MODE CSB-WL VREFP VREFN VMID VOUTL LRCIN DIN BCKIN MCLK ZERO DGND DVDD VOUTR AGND AVDD PLLVDD PLLGND PLLMODE GND OSC0 OSC0N VDD_IO XD0 XD1 XD2 XD3 XD4 XD5 XD6 VDDCORE XD7 XD8 XD9 GND XD10 XD11 VDD_IO XD12 XD13 XD14 XD15 GND VDD_IO GND VDD_IO XOEN XWEN XROMCSN XBSN1 XBSN0 GND PIOB6/XRAMCSN PIOA0/XIOCSN PIOB7/XWAIT VDD_IO XCASN XRASN XSDCLK XSDCSN XSDCKE XDQM1 XDQM0 TXCLK_N TXD0 TXD1 TXD2 TXD3 GND TXEN_N TXER_N VDD_IO CRS_N COL_N RXCLK_N VDD_CORE RXD0 RXD1 RXD2 RXD3 RXDV_N RXER_N MDC MDIO GND MCLK TEST0 OSC1 OSC1N GND VDD_IO PIOB5/DATAIN PIOA7/TXD PIOA6/RXD GND NTRST TCK TMS TDI TDO RESETN PIOC7 TEST1 TEST2 PIOC6 PIOC0 PIOC1 PIOC2 XA17 XA18 XA9 XA8 XA7 XA6 XA5 XA15 XA14 XA13 XA12 XA0 XA1 XA2 XA3 LRCK DOUT BCLK XA4 XA11 XA10 XA16 VDD_CORE (ETHERNET) PULSE TRANSFORMER ETHERNET INTERFACE SD-RAM FLASH MEMORY ETHERNET CONTROLLER +2.5V REGULATOR O G I ETHER+3.3V D/A CONVERTER A15 A14 A13 A12 A11 A10 A9 A8 NC NC WE RST RY/BY A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE VSS OE DQ0 DQ8 DQ1 DQ9 DQ2 DQ10 DQ3 DQ11 VDD DQ4 DQ12 DQ5 DQ13 DQ6 DQ14 DQ7 DQ15/A-1 VSS BYTE A16 NC NC MDIO MDC RXD1/PHYAD3 RXD3/PHYAD1 RXD2/PHYAD2 RXD0/PHYAD4 VDDIO GND RXDV/PCS_LPBK RXC RXER/ISO GND VDDC TXER TXC/REF_CLK TXEN TXD0 TXD1 TXD2 TXD3 COL/RMII CRS/RMII_LPBK GND VDDIO INT#/PHYAD0 LED0/TEST LED1/SPD100 LED2/DUPLEX LED3/NWAYEN PD# VDDRX RX- RX+ FXSD/FXEN GND GND REXT GND TX- TX+ VDDTX GND GND XO XI VDDPLL RST# VDDRCV(2.5V Supply) XA19 XA20 XA21 XA22 XA23 SAICLK MDO/SDO0 MDI/SDI0 MSK/SCLK0 MCS SCL/SCLK1 SDA/SDI1 SDO1 (Page 38) • See page 45 for Waveforms. • See page 49 for IC Block Diagrams. • See page 50 for IC Pin Function Description. w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 35 35 HCD-CZ1/NAS-CZ1 6-8. PRINTED WIRING BOARD – MAIN BOARD (COMPONENT SIDE) – • See page 30 for Circuit Boards Location. : Uses unleaded solder. MAIN BOARD (COMPONENT SIDE) 1-866-455- 11 (11) 1 2 3 4 5 6 7 8 9 10 11 12 A B C D E F G H I J K w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 36 36 HCD-CZ1/NAS-CZ1 6-9. PRINTED WIRING BOARD – MAIN BOARD (CONDUCTOR SIDE) – • See page 30 for Circuit Boards Location. : Uses unleaded solder. • Semiconductor Location Ref. No. Location D600 F-5 D601 F-5 D602 F-5 D603 E-5 D604 E-5 D605 E-5 D606 E-4 D607 E-4 D608 E-4 D609 D-5 D613 B-4 D621 C-5 D650 C-10 D651 E-11 IC601 E-8 IC602 F-4 IC603 E-6 IC604 D-4 IC650 C-11 IC701 I-7 Q600 G-7 Q601 F-6 Q602 F-6 Q603 D-6 Q604 C-6 Q605 D-6 Q606 D-6 Q607 C-9 Q731 J-3 Q761 G-6 Q831 J-3 Q860 J-10 Q861 G-6 Q862 J-10 CN751 CN600 IC650 C609 X600 CN651 CN650 CN700 CN605 C805 C904 C628 C802 C803 C806 C807 C808 C902 C903 C905 C906 C907 C908 CN602 C710 C613 C700 C703 C706 C605 C618 C713 C752 C804 C810 C811 C814 C815 C900 C909 C809 C912 C910 C640 C817 C626 C634 EPT701 L751 C901 C629 CN601 C913 C813 C812 C860 C911 C707 CN603 C635 C701 R681 R677 R679 R644 R648 R646 R649 IC601 IC701 IC604 IC602 IC603 FB803 FB802 FB801 D600 D601 D602 D603 D604 D605 D606 D607 D608 D609 D613 FB600 FB700 FB701 FB702 FB703 FB704 FB705 FB706 FB707 FB750 FB751 R860 Q600 Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q731 Q761 Q831 Q860 Q861 Q862 R602 R603 R604 R605 R606 R607 R609 R610 R611 R612 R613 R614 R615 R618 R619 R620 R622 R623 R624 R626 R627 R628 R629 R630 R631 R632 R633 R634 R635 R636 R637 R638 R639 R640 R641 R642 R645 R647 R650 R651 R652 R653 R654 R659 R660 R661 R662 R663 R664 R665 R666 R667 R668 R669 R670 R672 R673 R674 R675 R676 R680 R684 R685 R686 R687 R688 R689 R690 R691 R697 R698 R699 R700 R701 R702 R703 R704 R706 R710 R730 R731 R732 R733 R734 R735 R750 R751 R752 R753 R800 R801 R802 R862 R803 R804 R851 R852 R853 R854 R900 R901 R902 R903 R950 R951 R952 R953 C600 C601 C602 C603 C604 C607 C606 C608 C610 C611 C612 C614 C615 C616 C617 C620 C621 C622 C623 C624 C630 C631 C632 C633 C702 C704 C705 C708 C712 C714 C717 C800 C801 C816 C818 D650 D651 D621 R711 R721 R712 R722 C651 C661 R707 FB601 FB602 FB603 FB611 FB612 FB613 FB614 FB615 FB616 R705 1 100 81 80 51 50 31 30 E E E E E E E 1 21 42 22 E E E E E E E (CHASSIS) 1-866-455- 11 (11) (AEP, UK) (AEP, UK) ETHER BOARD CN501 (Page 33) B 1 1 14 3 PSAMP BOARD CN103 (Page 39) D FRONT PANEL BOARD CN1201 (Page 41) E FL BOARD CN1001 (Page 43) F (US) 1 3 5 4 1 3 5 4 1 3 5 4 NC CD BOARD CN201 (Page 31) A SUBPS BOARD CN115 (Page 39) G PSAMP BOARD CN202 (Page 39) C S601 DISC LID OPEN DETECT MAIN BOARD (CONDUCTOR SIDE) FM/AM TUNER PACK SUPPLIED WITH THE ASSEMBLED BLOCK FM 75Ω COAXIAL AM 1 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A B C D E F G H I J K w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 37 37 HCD-CZ1/NAS-CZ1 6-10. SCHEMATIC DIAGRAM – MAIN BOARD (1/2) – C813 C812 C811 C810 C809 C808 C815 R803 C807 R804 C806 C805 C818 C816 C817 C804 C803 C802 R802 C814 R801 C801 C706 C708 R735 R734 Q761 Q861 R733 R732 R731 C705 C710 C703 C704 C702 C717 C714 C712 C713 R951 R952 R852 R953 Q731 R853 R950 R854 R851 R860 C860 Q862 R862 Q860 C800 R800 FB801 FB802 FB803 R730 C707 CN650 EPT701 FB707 FB706 R707 FB705 FB704 FB703 FB702 FB701 FB700 C700 C701 FB750 R751 FB751 R750 R752 R753 C752 R903 C908 C913 C912 C911 C910 R901 C900 R900 C907 C906 C905 C904 C909 C903 C902 R902 C901 CN700 IC701 CN751 L751 100µH Q831 100 10V 10 50V 10 50V 10 50V 10 50V 0.022 10 50V 2.2k 0.022 10k 0.047 0.0047 0.1 0.1 470 16V 10 50V 0.022 0.022 47k 10 50V 1k 100p 100 10V 0.1 10k 10k 2SC3624 2SC3624 4.7k 1k 4.7k 100p 2.2 50V 100 10V 0.1 100p 0.1 0.1 0.1 100 10V 1k 10k 10k 10k 2SC3624 1k 1k 1k 10k 100k 1 50V DTC114EKA 0 DTA114EKA 100p 100 0 0 0 1k 2.2 50V 15P 100 0 0 0 0 100 10V 0.1 0 1k 0 100k 100k 1k 100 16V 10k 0.047 10 50V 10 50V 10 50V 10 50V 2.2k 10 50V 10k 0.022 0.022 0.047 0.0047 10 50V 0.022 0.022 47k 10 50V 27P M61529FP-D60G 2SC3624 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 11 81 82 83 57 84 85 86 58 52 54 69 53 73 70 32 43 33 34 41 42 68 63 62 64 65 46 45 DATA CLK 56 R-CH AGND L-CH HP IN AMP MUTE AMP STANDBY PROTECTOR POWER RELAY EVER+4V UNREG-SUB SUB-GND AUX-R AGND AUX-L (CHASSIS) CE DO CK DI L-CH +B(+9V) R-CH GND TUNER RDS DATA RDS CLK M+7V MGND MGND MP3STB MP3REQ MIACK MICK MIDIO MILP MP3(+3.3V) MP3RST MICS MP3GND SCOR SENS CLK XLT DATA XRST XTCN AVDD(+3.3V) ROUT AGND LOUT DGND DOUT DVDD(+3.3V) (1/2) 9P(US) 11P(AEP,UK) INPUT SELECT, ELECTRICAL VOLUME Q761,861 MUTING Q860,862 MUTING CONTROL MUTING Q731,831 NC(HP MUTE) AM COAXIAL FM 75Ω THE ASSEMBLED BLOCK SUPPLIED WITH FM/AM TUNER PACK (AEP,UK) (Page 32) (Page 40) (Page 38) (Page 38) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 38 38 HCD-CZ1/NAS-CZ1 6-11. SCHEMATIC DIAGRAM – MAIN BOARD (2/2) – D603 CN600 Q607 C631 C632 C633 R703 R702 R701 R700 R699 R698 R697 R691 R690 R689 R688 R687 R686 R685 R684 R704 R705 R706 C612 R647 R679 C622 CN601 FB611 FB612 FB613 FB614 FB615 FB616 CN602 D621 C628 C635 C640 C621 IC604 D608 D607 D606 D605 C618 C615 C607 CN603 R680 C626 C624 D609 R674 R669 Q605 C617 C616 D604 C611 C610 R645 D602 C606 C605 C608 Q603 Q604 D600 R633 R632 D601 R641 X600 R652 R642 R638 R636 R634 R630 R626 R624 C613 R664 R665 C620 C623 R676 R675 R672 R670 R667 R668 C614 R662 R663 R661 R660 R654 R653 R651 R650 R640 R639 R710 R627 R629 R631 R635 R637 R615 R614 R613 R612 R611 R610 R609 R607 R620 R619 C603 R606 R605 R604 R603 C602 R602 C604 Q602 R623 R622 Q601 R618 CN605 C600 C601 R722 R712 R711 R721 C629 C630 C634 IC650 CN651 R628 IC602 R673 Q606 Q600 R659 R649 R646 R648 R644 FB600 IC603 R681 C609 FB601 FB602 FB603 C627 C661 C651 S601 IC601 µPD703261YGF-S06 R666 R677 D613 D650 D651 1SS355 14P DTA114EKA 0.001 0.001 0.001 100 1k 1k 100 100 100 100 100 100 100 100 100 1k 1k 1k 10k 10k 10k 0.1 1k 0.1 15P 0 0 0 13P 1SS355 0.1 100 10V 220 16V 0.1 NJM2870F38(TE2) 1SS355 1SS355 1SS355 1SS355 47 10V 0.01 0.1 4P 47k 1000 6.3V 0.1 1SS355 100k 47k DTC114EKA- T146 0.22 0.1 1SS355 0.1 0.1 4.7k 1SS355 0.1 10 50V 0.22 DTC114EKA DTA114EKA RB501V-40TE-17 220 10k 1SS355 47k 5MHz 100k 10k 1k 100 100 100 100 100 4.7 50V 10k 100 0.001 0.001 10k 100 100 100 100 10k 0.01 100 10k 100 10k 100 100 1k 100 1k 100 4.7k 1k 100 100 100 100 100 100 100 100 100 100 1k 1k 47 47 0.1 100 100 1k 100 0.001 10k 0.1 2SC1623 47k 47k 2SC1623 470k 7P 22p 22p 100k 100k 100 100 220 10V 0.1 1000 16V TA78033LS 15P 1k PST3629 100k 2SC1623 DTA114EKA 1k 1k 1k 1k 1k SN74AHC1GU04DCKR 47k 0.22F 5.5V 0 0 0 1000p 1000p -JBT-A 470 47k EC10DS2 EC10DS2 EC10DS2 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 11 97 96 95 94 93 47 39 31 30 29 27 26 25 24 10 31 30 29 27 100 99 98 97 96 95 94 93 47 39 28 28 75 76 77 25 26 24 10 63 64 65 73 52 53 58 57 77 76 75 70 69 68 61 60 62 54 56 CLK DATA 60 61 32 33 34 41 42 43 45 46 81 82 83 84 85 86 98 99 100 * VF VF FL-30V MP3-GND DGND UCOM-GND ETHER+4V D+4V MGND M+7V AGND A+9V LED1 LED2 LED3 LED4 LED5 GND GND LED+7V KEY2 KEY1 KEY0 D GND STBY-LED LED6 LED7 DGND EVER+3.3V SITCS FL-RESET FL-CS FL-CLK FL-DATA D+3.3V DGND FL-30V VF VF GND SUBAC SUBAC GND CD_OPEN_CLOSE GND VDD SI SCK SO FLMD0 RESET DA-GND ROUT DA-GND LOUT A-GND A+3.3V D-GND NRESET PDOWN IICDATA IICCLK D-GND ETHER+3.3V ETHER-GND (2/2) D-GND MUTING SWITCH I G O +3.3V REGULATOR (AEP,UK) (US) SYSTEM CONTROLLER NC Q603,604 MODE CONTROL VOLTAGE DETECT INVERTER +3.8V REGULATOR Q605,606 RESET SWITCH OUT IN CTL GND MUTING SWICTH ST-GND OPEN DETECT DISC LID FL-GND NO_USE7 NO_USE6 NO_USE5 LED6 GEQ_DATA GEQ_CLK LINE_MUTE POWER_RELAY SPK_RELAY NO_USE3 LED7 12C_CLK 12C_DATA HP_MUTE EVDD EVSS AMP_STBY AMP_MUTING HP_IN FL_RESET SIRCS FL_DATA FLASH_DO FLASH_DI AC_CUT (CAN'T_USE) FLASH_CLK RM_INT KEY_INT SELF_PROG XT2 XT1 RESET X2 X1 VSS REGC VDD FLASH0 NO_USE2 STBY_LED AVREF1 SOFT-CHECK NO_USE1 AVSS AVREF0 DEST MODEL O-MP3-STBY I-MP3-REQ I-MP3-ACK O-MILP O-MICS O-MP3RST O-AMUTE DEVICE_ON_OFF NO_USE14 NO_USE15 NO_USE16 NO_USE17 LED5 LED4 LED3 LED2 LED1 KEY2 KEY1 KEY0 NO_USE8 I-SENS O-DATA O-CLOCK I-MP3DATA O-MP3DATA O-MP3CLK I-SCOR NO_USE9 RDS_CLK RDS_DATA PLL-CLK PLL-DI PLL-DO PLL-CE NO_USE10 NO_USE11 TUNED O-XTL O-XTCN BVSS BVDD O-XRST O-CD_ON CD_OPEN_CLOSE ETHER-NRESET ETHER-PDOWN FLASH1 NO_ USE12 NO_ USE13 *R679 (US) FL_ CS CLK FL_ Q601,602 BUFFER 22k(US) 4.7k(AEP,UK) (Page 37) (Page 34) (Page 37) (Page 40) (Page 44) (Page 42) (Page 40) • See page 45 for Waveforms. • See page 48 for IC Block Diagrams. • See page 52 for IC Pin Function Description. w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 39 39 HCD-CZ1/NAS-CZ1 6-12. PRINTED WIRING BOARDS – POWER SECTION – • See page 30 for Circuit Boards Location. : Uses unleaded solder. Ref. No. Location Ref. No. Location D1 E-3 D101 D-4 D111 F-7 D112 E-10 D113 F-9 D114 F-10 D131 E-11 D132 E-11 D133 E-11 D134 E-11 D135 E-11 D136 E-17 D261 C-4 • Semiconductor Location D821 C-6 IC111 C-10 IC112 D-10 IC113 D-10 IC114 E-10 IC201 B-L Q1 B-3 Q131 E-12 Q261 C-7 Q262 C-7 Q263 C-7 EP201 F1 F101 F102 R823 JW120 JW121 JW122 JW124 JW125 JW126 JW127 JW128 JW129 JW130 JW131 JW132 JW133 JW134 JW135 JW136 JW137 JW138 JW139 JW140 JW141 JW142 JW143 JW144 JW145 JW146 JW147 JW148 JW149 JW150 JW151 JW152 JW153 JW154 JW155 JW156 JW157 JW158 JW159 CN202 C265 C264 D101 C104 C103 EP1 EP101 R1 RY1 C1 CN3 C101 C102 IC201 C201 C202 C321 C221 C324 C224 CN101 R228 R328 R227 R327 CN103 IC111 IC112 IC113 C117 C121 C124 C115 C118 C122 C113 D131 D132 D133 D134 R111 R131 C111 C112 C132 Q131 C134 R135 C125 C262 C263 J202 CN102 J201 R132 R134 C114 IC114 LF1 LINE FILTER CN1 EP202 CN201 FB111 R2 CN2 RY201 D114 D113 D111 D112 JW160 JW161 JW162 C225 C325 C326 R225 R325 C231 C232 C331 C332 C226 C116 C119 C123 C126 D261 R252 R352 C251 C351 R264 D1 R224 R324 R323 R322 R222 R221 R321 R223 C223 C323 C267 FB341 FB241 C243 C343 C329 C330 C229 C230 R229 R329 D821 Q261 Q262 Q263 R226 R326 R261 R262 C261 C266 R151 R152 R153 D135 D136 R158 R133 R156 R155 R157 C133 R351 R251 R263 C131 Q1 R3 C268 C203 C204 CN5 CN115 1 4 2 1 SP101 (BACK TWEETER) SP102 (FRONT TWEETER) SP103 (WOFFER) YEL L–CH R–CH BLK BLK BLU RED RED/BLK RED RED/BLK 4 3 SP201 (BACK TWEETER) SP202 (FRONT TWEETER) SP203 (WOFFER) YEL BLK BLK BLU RED RED/BLK RED RED/BLK 2 1 2 1 (AC IN) C MAIN BOARD CN650 (Page 36) PSAMP BOARD (CHASSIS) E 1 1 2 15 14 T1 MAIN POWER TRANSFORMER 1 3 1 2 1 2 1 2 1 2 1 6 1 3 6 1 PHONES ANALOG IN (US) B C E 1-866-457- 11 (11) T2 SUB POWER TRANSFORMER SUBPS BOARD MAIN BOARD CN603 (Page 36) G 1-866-458- 11 (11) D MAIN BOARD CN600 (Page 36) (CHASSIS) (CHASSIS) A B C D E F G H 1 2 3 4 5 6 7 8 9 10 11 12 (CHASSIS) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 40 40 HCD-CZ1/NAS-CZ1 6-13. SCHEMATIC DIAGRAM – POWER SECTION – Q131 CN202 R351 R251 R352 R252 C251 C351 C268 EP101 CN2 CN1 EP1 CN3 RY1 D1 C104 F102 D101 F101 C102 C101 C103 C266 R322 R222 C323 C324 R323 D261 R3 R263 R264 C265 Q1 C264 C321 R321 R221 C221 IC201 C223 R224 R324 R223 C224 R326 R226 C261 R261 C262 C263 Q261 Q262 Q263 FB341 FB241 C343 C203 C243 EP202 EP201 C331 C231 C330 C329 C230 R229 C229 D821 RY201 R227 CN201 CN103 R151 C115 IC111 C118 IC112 C117 C114 IC113 IC114 C121 C124 C113 FB111 C122 C125 R158 R155 R156 R157 R153 R152 R135 R134 D136 R133 C134 D135 C133 R132 C132 D134 D133 D132 D131 C131 R131 C267 CN101 CN102 R327 R262 J202 R228 R328 R823 C112 D112 D111 D113 D114 R111 C111 SP201 SP202 SP203 SP102 T1 J201 R1 LF1 R2 CN115 T2 CN5 C1 F1 C202 C201 R329 SP101 SP103 C116 C119 C123 C126 C232 C332 C204 R225 C225 C226 C326 C325 R325 2SB1375 15P 1k 1k 3.3k 3.3k 220p 220p 0.1 2P 2P 2P 1SS355 2200 35V D3SBA20 0.1 0.1 2200 35V 0.1 33k 33k 180p 47 25V 1k 1SS355 4.7k 4.7k 22k 22 25V 2SC1623 1000 6.3V 4.7 50V 1k 1k 4.7 50V LM1876TF 180p 27k 27k 1k 47 25V 47k 56k 0.1 56k 100 16V 47 50V 2SC1623 2SC1623 2SC1623 0.001 0.1 0.001 0.1 0.1 0.1 0.1 0.1 10 0.1 1SS355 220 1/2W 4P 14P 0 22 16V TA7809LS 22 16V TA7807S 47 25V 47 25V TA7804LS TA7804LS 47 25V 47 25V 4700 25V 1.1UH 22 16V 22 16V 0 0 0 0 0 0 470 470 UDZ-TE-17 4.7B 10k 10 50V UDZ-TE-17 30B 0.1 2.2k 100 50V 10EDB40 10EDB40 10EDB40 10EDB40 0.1 4.7 0.1 3P 6P 220 1/2W 100k 180 1/2W 0.1 21DQ04 21DQ04 21DQ04 21DQ04 0.33 0.1 (BACK TWEETER) (FRONT TWEETER) (WOOFER) (FRONT TWEETER) LINE FILTER 3.3M 2P 2P 0.01 250V 1 1 10 (BACK TWEETER) (WOOFER) 0.1 0.1 0.1 0.1 0.1 0.1 0.1 10 0.1 0.1 0.1 0.1 10 ∗ ∗ ∗ R-CH AGND L-CH HP IN NC(HP MUTE) AMP MUTE AMP STANDBY PROTECTOR POWER RELAY EVER+4V UNREG-SUB SUB-GND AUX-R AGND AUX-L (CHASSIS) (CHASSIS) NEUTRAL 120/230V NEUTRAL LIVE (CHASSIS) (CHASSIS) (CHASSIS) (CHASSIS) OUTB VCCA OUTA VEE GNDA MUTEA -INA +INA STANDBYA GNDB MUTEB -INB +INB STANDBYB VCCB ST-GND A+9V AGND M+7V MGND D+4V ETHER+4V UCOM-GND DGND MP3-GND FL-GND FL-30V VF VF PHONES POWER AMP RELAY DRIVE Q261,262 OVER LOAD DETECT SP_R+ SP_R- SP_L+ SP_L- I O G I G O I G O I G O +9V REGULATOR +7V REGULATOR +4V REGULATOR +4V REGULATOR -30V REGULATOR R-CH L-CH T1.6A 250V(AEP,UK) 2A 125V(US) MAIN POWER TRANSFORMER RELAY DRIVE ANALOG IN 3.15A 125V(US) T3.15A 250V(AEP,UK) (AC IN) (US) SUB-AC SUB-AC 120/230V NEUTRAL SUB POWER TRANSFORMER ∗F1 ∗F101,102 (Page 38) (Page 37) (Page 38) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 41 41 HCD-CZ1/NAS-CZ1 6-14. PRINTED WIRING BOARDS – PANEL SECTION – • See page 30 for Circuit Boards Location. : Uses unleaded solder. Ref. No. Location Ref. No. Location D1201 H-4 D1202 H-6 D1203 H-7 D1204 H-8 D1205 H-9 D1251 H-2 D1272 C-3 • Semiconductor Location Q1201 G-13 Q1202 G-13 Q1203 G-13 Q1204 G-12 Q1205 G-12 Q1272 B-4 JR1202 JR1203 JR1204 JR1205 JR1201 JR1206 S1202 CN1201 CN1202 S1201 S1203 S1204 S1205 S1251 S1252 S1256 S1257 S1261 S1263 C1251 C1211 C1212 C1213 C1214 C1215 R1216 R1217 R1218 R1219 R1220 R1221 R1222 R1223 R1224 R1261 R1262 R1251 R1252 Q1201 Q1202 Q1203 Q1204 Q1205 D1201 D1202 D1203 D1204 D1205 C1202 C1252 D1251 Q1272 S1271 CN1271 R1275 R1277 C1272 C1275 D1272 JL1272 E E E E E 1-866-459- 11 (11) FRONT PANEL BOARD VOL. + VOL. – FUNCTION x N D1251, S1251 D1201, S1201 1 D1202, S1202 2 D1203, S1203 3 D1204, S1204 4 D1205, S1205 5 S1201 –1205, 1251, 1252, S1256, 1257, 1261, 1263, 1271 MAIN BOARD CN601 (Page 36) E E 1-866-460- 11 (11) TOP PANEL BOARD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 A B C D E F G H w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 42 42 HCD-CZ1/NAS-CZ1 6-15. SCHEMATIC DIAGRAM – PANEL SECTION – CN1201 R1252 R1251 R1261 R1262 C1252 R1224 R1223 R1222 R1221 C1202 C1251 CN1202 Q1205 Q1204 C1214 C1215 R1220 R1219 C1213 R1218 Q1203 Q1202 Q1201 C1212 R1217 C1211 R1216 CN1271 JL1272 R1275 C1272 S1271 R1277 C1275 S1251 S1201 S1202 S1203 S1204 S1205 S1256 S1257 S1261 S1263 D1251 Q1272 D1272 D1205 D1204 D1203 D1202 D1201 S1252 15P 2.2k 1k 1k 2.2k 0.01 4.7k 2.2k 2.2k 1k 0.01 0.01 7P DTC114EKA DTC114EKA 0.01 0.01 820 820 0.01 820 DTC114EKA DTC114EKA DTC114EKA 0.01 820 0.01 820 7P 0 820 0.01 2.2k 0.01 SML-310LTT86 DTC114EKA QSMN-C186 QSMN-C186 QSMN-C186 QSMN-C186 QSMN-C186 QSMN-C186 NC KEY2 DGND NC(LED7) LED6 GND LED+7V LED7 LED6 STBY-LED DGND KEY0 KEY1 KEY2 LED+7V GND GND LED5 LED4 LED3 LED2 LED1 +LED7V GND LED6 NC(LED7) DGND KEY2 NC FUNCTION 1 2 3 4 5 VOL.- VOL.+ LED DRIVE NETWORK NETWORK Q1201-1205 LED DRIVE 1 2 3 4 5 (Page 38) w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 43 43 HCD-CZ1/NAS-CZ1 6-16. PRINTED WIRING BOARD – FL BOARD – • See page 30 for Circuit Boards Location. : Uses unleaded solder. IC1011 CN1001 C1024 C1025 C1026 C1023 C1027 C1029 C1031 C1033 C1035 C1037 C1038 C1036 C1034 C1032 C1030 C1028 C1006 C1007 C1003 C1002 C1001 R1001 R1008 R1007 C1011 IC1001 C1008 R1006 R1002 R1003 R1004 R1005 Q1001 1 3 E FL1001 FLUORESCENT INDICATOR TUBE 1 16 17 32 33 48 49 64 FL BOARD (CONDUCTOR SIDE) 1-866-456- 11 (11) MAIN BOARD CN602 (Page 36) F 1-866-456- 11 (11) FL BOARD (COMPONENT SIDE) 1 2 3 4 5 6 7 8 9 10 11 12 13 A B C D E F G H w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com HCD-CZ1/NAS-CZ1 44 44 HCD-CZ1/NAS-CZ1 6-17. SCHEMATIC DIAGRAM – FL BOARD – CN1001 C1011 R1008 Q1001 R1007 R1005 R1004 R1003 R1002 R1001 C1001 C1002 C1003 R1006 C1008 C1007 C1006 C1023 C1024 C1025 C1026 C1027 C1028 C1029 C1030 C1031 C1032 C1033 C1034 C1035 C1036 C1037 C1038 IC1011 IC1001 FL1001 13P 0.01 1k 2SC3052EF 100k 1k 1k 1k 1k 100k 0.01 100p 100p 10k 220p 22 6.3V 10 50V 220p 220p 220p 220p 220p 220p 220p 220p 220p 220p 220p 220p 220p 220p 220p 220p RPM7240-H8 M66005-0151AHP FLUORECSENT INDICATOR TUBE DIG4 DIG5 DIG6 DIG7 DIG8 DIG9 DIG10 DIG11 DIG12 DIG13 DIG14 DIG15 SEG0 SEG1 SEG2 DIG4 DIG5 DIG6 DIG7 DIG8 DIG9 DIG10 DIG11 DIG12 DIG13 DIG14 DIG15 SEG0 SEG1 SEG2 DIG1 DIG2 DIG3 DIG1 DIG2 DIG3 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG33 SEG32 SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG34 SEG34 F1 1G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G 15G 4G 3G 2G P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23 P24 P25 P26 P27 P35 P34 P33 P32 P31 P30 P29 P28 NP NP F2 16G F1 NP NP F2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 Vcc 2 DIG12 DIG13 DIG14 DIG15 SEG0 SEG1 SEG2 DIG4 DIG5 DIG6 DIG7 DIG8 DIG9 DIG10 DIG11 RST SCK SDATA XOUT XIN Vcc Vss DIG0 DIG1 DIG2 DIG3 SEG34 SEG35 P OFF SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 VP. SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 CS P1 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G 15G 16G 1G GND VF FL-30V DGND D+3.3V FL-DATA FL-CLK FL-CS FL-RESET SIRCS EVER+3.3V DGND VF FL DRIVER REMOTE CONTROL RECEIVER GRID DRIVE (Page 38) • See page 45 for Waveforms. w w w . x i a o y u 1 6 3 . c o m Q Q 3 7 6 3 1 5 1 5 0 9 9 2 8 9 4 2 9 8 T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 45 HCD-CZ1/NAS-CZ1 – ETHER Board – – CD Board – – MAIN Board – – FL Board – wa IC601 qg (X2) 1 V/DIV, 0.1 µs/DIV 0.2 µs 2.9 Vp-p qa IC501 rg (XO) 1 V/DIV, 20 ns/DIV 40.1 ns 2.4 Vp-p qs IC502 C10 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V C11 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3V C14 1-164-360-11 CERAMIC CHIP 0.1uF 16V C15 1-164-360-11 CERAMIC CHIP 0.1uF 16V C16 1-115-156-11 CERAMIC CHIP 1uF 10V C17 1-126-246-11 ELECT CHIP 220uF 20% 4V C18 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C111 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C112 1-164-315-11 CERAMIC CHIP 470PF 5% 50V C113 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C114 1-164-315-11 CERAMIC CHIP 470PF 5% 50V C115 1-164-360-11 CERAMIC CHIP 0.1uF 16V C116 1-128-995-21 ELECT CHIP 100uF 20% 10V C122 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C123 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C124 1-162-959-11 CERAMIC CHIP 330PF 5% 50V C125 1-164-360-11 CERAMIC CHIP 0.1uF 16V C131 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C132 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V C133 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C134 1-164-360-11 CERAMIC CHIP 0.1uF 16V C141 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C142 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V C143 1-164-360-11 CERAMIC CHIP 0.1uF 16V C151 1-128-995-21 ELECT CHIP 100uF 20% 10V C161 1-164-360-11 CERAMIC CHIP 0.1uF 16V C162 1-164-360-11 CERAMIC CHIP 0.1uF 16V C163 1-164-360-11 CERAMIC CHIP 0.1uF 16V C171 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C172 1-162-920-11 CERAMIC CHIP 27PF 5% 50V C174 1-164-360-11 CERAMIC CHIP 0.1uF 16V C181 1-164-360-11 CERAMIC CHIP 0.1uF 16V C182 1-164-360-11 CERAMIC CHIP 0.1uF 16V C183 1-124-778-00 ELECT CHIP 22uF 20% 6.3V C184 1-124-778-00 ELECT CHIP 22uF 20% 6.3V C185 1-164-315-11 CERAMIC CHIP 470PF 5% 50V C186 1-164-315-11 CERAMIC CHIP 470PF 5% 50V C194 1-164-360-11 CERAMIC CHIP 0.1uF 16V C195 1-164-360-11 CERAMIC CHIP 0.1uF 16V C196 1-164-360-11 CERAMIC CHIP 0.1uF 16V C201 1-128-995-21 ELECT CHIP 100uF 20% 10V C203 1-128-995-21 ELECT CHIP 100uF 20% 10V C209 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C210 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C211 1-164-230-11 CERAMIC CHIP 220PF 5% 50V C212 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C213 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C251 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V C252 1-164-360-11 CERAMIC CHIP 0.1uF 16V C255 1-164-360-11 CERAMIC CHIP 0.1uF 16V C257 1-164-360-11 CERAMIC CHIP 0.1uF 16V C258 1-164-360-11 CERAMIC CHIP 0.1uF 16V C259 1-164-360-11 CERAMIC CHIP 0.1uF 16V C260 1-128-394-11 ELECT CHIP 220uF 20% 10V C302 1-164-360-11 CERAMIC CHIP 0.1uF 16V C303 1-164-360-11 CERAMIC CHIP 0.1uF 16V C305 1-126-246-11 ELECT CHIP 220uF 20% 4V C306 1-164-360-11 CERAMIC CHIP 0.1uF 16V C307 1-164-360-11 CERAMIC CHIP 0.1uF 16V C308 1-126-208-21 ELECT CHIP 47uF 20% 4V C309 1-164-360-11 CERAMIC CHIP 0.1uF 16V C310 1-164-360-11 CERAMIC CHIP 0.1uF 16V C311 1-164-360-11 CERAMIC CHIP 0.1uF 16V C312 1-164-360-11 CERAMIC CHIP 0.1uF 16V C313 1-164-360-11 CERAMIC CHIP 0.1uF 16V C314 1-126-208-21 ELECT CHIP 47uF 20% 4V C315 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C316 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C317 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C318 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C320 1-216-864-11 SHORT CHIP 0 < CONNECTOR > CN101 1-770-425-11 CONNECTOR, FFC/FPC 16P CN201 1-818-350-11 CONNECTOR (FFC) 27P < FERRITE BEAD > FB301 1-500-445-21 FERRITE, EMI (SMD) (2012) < IC > IC101 8-752-425-12 IC CXD3059AR IC251 6-705-808-01 IC BA5947FM-E2 NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u: µ, for example: uA... : µA... uPA... : µPA... uPB... : µPB... uPC... : µPC... uPD... : µPD... • CAPACITORS uF: µF • COILS uH: µH CD The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 62 HCD-CZ1/NAS-CZ1 IC301 6-705-365-01 IC TC94A34FG-002 IC303 6-705-807-01 IC BH15FB1WG < TRANSISTOR > Q10 6-551-120-01 TRANSISTOR 2SA2119K < RESISTOR/FERRITE BEAD > R10 1-216-791-11 METAL CHIP 3.3 5% 1/10W R11 1-216-864-11 SHORT CHIP 0 R12 1-216-845-11 METAL CHIP 100K 5% 1/10W R13 1-218-446-11 METAL CHIP 1 5% 1/10W R111 1-216-821-11 METAL CHIP 1K 5% 1/10W R112 1-216-835-11 METAL CHIP 15K 5% 1/10W R113 1-216-821-11 METAL CHIP 1K 5% 1/10W R114 1-216-835-11 METAL CHIP 15K 5% 1/10W R121 1-216-835-11 METAL CHIP 15K 5% 1/10W R131 1-216-857-11 METAL CHIP 1M 5% 1/10W R132 1-216-833-11 METAL CHIP 10K 5% 1/10W R133 1-216-848-11 METAL CHIP 180K 5% 1/10W R141 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R142 1-216-821-11 METAL CHIP 1K 5% 1/10W R143 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R151 1-216-864-11 SHORT CHIP 0 R161 1-216-809-11 METAL CHIP 100 5% 1/10W R162 1-216-841-11 METAL CHIP 47K 5% 1/10W R163 1-216-809-11 METAL CHIP 100 5% 1/10W R165 1-216-864-11 SHORT CHIP 0 R166 1-216-821-11 METAL CHIP 1K 5% 1/10W R167 1-216-809-11 METAL CHIP 100 5% 1/10W R171 1-216-817-11 METAL CHIP 470 5% 1/10W R172 1-216-857-11 METAL CHIP 1M 5% 1/10W R173 1-216-295-00 SHORT CHIP 0 R181 1-216-809-11 METAL CHIP 100 5% 1/10W R182 1-216-809-11 METAL CHIP 100 5% 1/10W R191 1-216-864-11 SHORT CHIP 0 R201 1-500-445-21 FERRITE, EMI (SMD) (2012) R203 1-216-864-11 SHORT CHIP 0 R204 1-500-445-21 FERRITE, EMI (SMD) (2012) R205 1-216-864-11 SHORT CHIP 0 R251 1-216-833-11 METAL CHIP 10K 5% 1/10W R252 1-216-837-11 METAL CHIP 22K 5% 1/10W R253 1-216-833-11 METAL CHIP 10K 5% 1/10W R301 1-216-845-11 METAL CHIP 100K 5% 1/10W R302 1-216-833-11 METAL CHIP 10K 5% 1/10W R303 1-216-845-11 METAL CHIP 100K 5% 1/10W R305 1-216-845-11 METAL CHIP 100K 5% 1/10W R306 1-216-864-11 SHORT CHIP 0 R307 1-216-833-11 METAL CHIP 10K 5% 1/10W R313 1-216-813-11 METAL CHIP 220 5% 1/10W R351 1-216-809-11 METAL CHIP 100 5% 1/10W R352 1-216-809-11 METAL CHIP 100 5% 1/10W R353 1-216-809-11 METAL CHIP 100 5% 1/10W R354 1-216-809-11 METAL CHIP 100 5% 1/10W R401 1-216-809-11 METAL CHIP 100 5% 1/10W R402 1-216-809-11 METAL CHIP 100 5% 1/10W R403 1-216-809-11 METAL CHIP 100 5% 1/10W R404 1-216-809-11 METAL CHIP 100 5% 1/10W R405 1-216-809-11 METAL CHIP 100 5% 1/10W R406 1-216-809-11 METAL CHIP 100 5% 1/10W R407 1-216-809-11 METAL CHIP 100 5% 1/10W R408 1-216-809-11 METAL CHIP 100 5% 1/10W R409 1-216-809-11 METAL CHIP 100 5% 1/10W R410 1-216-809-11 METAL CHIP 100 5% 1/10W R411 1-216-809-11 METAL CHIP 100 5% 1/10W R412 1-216-809-11 METAL CHIP 100 5% 1/10W R419 1-216-809-11 METAL CHIP 100 5% 1/10W < VIBRATOR > X171 1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz) ************************************************************ A-1099-020-A ETHER BOARD, COMPLETE *********************** < CAPACITOR > C501 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C503 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C504 1-164-360-11 CERAMIC CHIP 0.1uF 16V C505 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C507 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C508 1-164-360-11 CERAMIC CHIP 0.1uF 16V C509 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C510 1-164-360-11 CERAMIC CHIP 0.1uF 16V C511 1-164-360-11 CERAMIC CHIP 0.1uF 16V C512 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V C513 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V C514 1-135-787-11 CERAMIC CHIP 0.001uF 10% 2KV C515 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C516 1-164-360-11 CERAMIC CHIP 0.1uF 16V C517 1-124-779-00 ELECT CHIP 10uF 20% 16V C518 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C519 1-164-360-11 CERAMIC CHIP 0.1uF 16V C520 1-164-360-11 CERAMIC CHIP 0.1uF 16V C521 1-164-360-11 CERAMIC CHIP 0.1uF 16V C522 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C523 1-164-360-11 CERAMIC CHIP 0.1uF 16V C524 1-124-779-00 ELECT CHIP 10uF 20% 16V C525 1-164-360-11 CERAMIC CHIP 0.1uF 16V C527 1-164-360-11 CERAMIC CHIP 0.1uF 16V C528 1-164-360-11 CERAMIC CHIP 0.1uF 16V C529 1-164-360-11 CERAMIC CHIP 0.1uF 16V C530 1-164-360-11 CERAMIC CHIP 0.1uF 16V C531 1-124-779-00 ELECT CHIP 10uF 20% 16V C532 1-164-360-11 CERAMIC CHIP 0.1uF 16V C533 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C534 1-164-360-11 CERAMIC CHIP 0.1uF 16V C535 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V C536 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V C537 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C538 1-162-918-11 CERAMIC CHIP 18PF 5% 50V C539 1-162-918-11 CERAMIC CHIP 18PF 5% 50V C540 1-164-360-11 CERAMIC CHIP 0.1uF 16V C541 1-164-360-11 CERAMIC CHIP 0.1uF 16V C542 1-164-360-11 CERAMIC CHIP 0.1uF 16V C543 1-126-205-11 ELECT CHIP 47uF 20% 6.3V CD ETHER www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 63 HCD-CZ1/NAS-CZ1 C544 1-164-360-11 CERAMIC CHIP 0.1uF 16V C545 1-164-360-11 CERAMIC CHIP 0.1uF 16V C546 1-164-360-11 CERAMIC CHIP 0.1uF 16V C547 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V C548 1-164-360-11 CERAMIC CHIP 0.1uF 16V C549 1-164-360-11 CERAMIC CHIP 0.1uF 16V C550 1-164-360-11 CERAMIC CHIP 0.1uF 16V C551 1-164-360-11 CERAMIC CHIP 0.1uF 16V C552 1-164-360-11 CERAMIC CHIP 0.1uF 16V C553 1-164-360-11 CERAMIC CHIP 0.1uF 16V C554 1-164-360-11 CERAMIC CHIP 0.1uF 16V C555 1-164-360-11 CERAMIC CHIP 0.1uF 16V C556 1-124-779-00 ELECT CHIP 10uF 20% 16V C557 1-164-360-11 CERAMIC CHIP 0.1uF 16V C558 1-126-205-11 ELECT CHIP 47uF 20% 6.3V C559 1-164-360-11 CERAMIC CHIP 0.1uF 16V C562 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C563 1-124-779-00 ELECT CHIP 10uF 20% 16V C564 1-164-360-11 CERAMIC CHIP 0.1uF 16V C565 1-124-779-00 ELECT CHIP 10uF 20% 16V C566 1-164-360-11 CERAMIC CHIP 0.1uF 16V C567 1-164-360-11 CERAMIC CHIP 0.1uF 16V C568 1-164-360-11 CERAMIC CHIP 0.1uF 16V C569 1-124-779-00 ELECT CHIP 10uF 20% 16V C571 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C572 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < CONNECTOR > CN501 1-573-829-11 CONNECTOR, BOARD TO BOARD 15P < DIODE > D501 8-719-988-61 DIODE 1SS355TE-17 D502 8-719-988-61 DIODE 1SS355TE-17 D503 8-719-988-61 DIODE 1SS355TE-17 D504 8-719-988-61 DIODE 1SS355TE-17 D505 8-719-988-61 DIODE 1SS355TE-17 D506 8-719-988-61 DIODE 1SS355TE-17 D511 8-719-987-69 DIODE DAN217 D512 8-719-987-69 DIODE DAN217 D513 8-719-987-69 DIODE DAN217 D514 8-719-987-69 DIODE DAN217 < EARTH TERMINAL > EP501 1-537-738-21 TERMINAL, GROUND < FERRITE BEAD/JUMPER RESISTOR > FB502 1-216-864-11 SHORT CHIP 0 FB503 1-216-864-11 SHORT CHIP 0 FB504 1-216-864-11 SHORT CHIP 0 FB505 1-216-864-11 SHORT CHIP 0 FB506 1-414-618-21 FERRITE, EMI (SMD) (2012) FB507 1-500-245-11 FERRITE, EMI (SMD) (2012) FB508 1-216-864-11 SHORT CHIP 0 FB509 1-216-864-11 SHORT CHIP 0 FB510 1-216-864-11 SHORT CHIP 0 FB511 1-414-618-21 FERRITE, EMI (SMD) (2012) FB512 1-500-245-11 FERRITE, EMI (SMD) (2012) FB513 1-500-245-11 FERRITE, EMI (SMD) (2012) FB515 1-500-245-11 FERRITE, EMI (SMD) (2012) FB516 1-500-245-11 FERRITE, EMI (SMD) (2012) FB517 1-500-245-11 FERRITE, EMI (SMD) (2012) FB518 1-500-245-11 FERRITE, EMI (SMD) (2012) FB519 1-500-245-11 FERRITE, EMI (SMD) (2012) FB520 1-500-245-11 FERRITE, EMI (SMD) (2012) FB521 1-500-245-11 FERRITE, EMI (SMD) (2012) < IC > IC501 6-706-606-01 IC KSZ8721BL IC502 6-706-610-01 IC ML7201TB IC503 6-703-791-01 IC MSM56V16160F-8T3FM1 IC504 (Not supplied) IC MBM29LV800TA-CZ1 IC505 6-706-604-01 IC WM8728SEDS/R IC506 6-700-394-01 IC BA25BC0FP-E2 < JACK > J501 1-815-920-11 JACK, MODULAR (ETHERNET) < RESISTOR > R501 1-218-823-11 METAL CHIP 100 0.5% 1/10W R502 1-218-823-11 METAL CHIP 100 0.5% 1/10W R503 1-218-823-11 METAL CHIP 100 0.5% 1/10W R504 1-218-823-11 METAL CHIP 100 0.5% 1/10W R505 1-218-823-11 METAL CHIP 100 0.5% 1/10W R506 1-218-823-11 METAL CHIP 100 0.5% 1/10W R507 1-218-823-11 METAL CHIP 100 0.5% 1/10W R508 1-218-823-11 METAL CHIP 100 0.5% 1/10W R509 1-216-819-11 METAL CHIP 680 5% 1/10W R510 1-216-833-11 METAL CHIP 10K 5% 1/10W R511 1-218-874-11 METAL CHIP 13K 0.5% 1/10W R512 1-216-833-11 METAL CHIP 10K 5% 1/10W R513 1-216-833-11 METAL CHIP 10K 5% 1/10W R514 1-216-833-11 METAL CHIP 10K 5% 1/10W R515 1-216-833-11 METAL CHIP 10K 5% 1/10W R516 1-216-833-11 METAL CHIP 10K 5% 1/10W R517 1-216-857-11 METAL CHIP 1M 5% 1/10W R518 1-216-857-11 METAL CHIP 1M 5% 1/10W R519 1-216-833-11 METAL CHIP 10K 5% 1/10W R521 1-216-864-11 SHORT CHIP 0 R522 1-216-809-11 METAL CHIP 100 5% 1/10W R523 1-216-809-11 METAL CHIP 100 5% 1/10W R524 1-216-809-11 METAL CHIP 100 5% 1/10W R525 1-216-809-11 METAL CHIP 100 5% 1/10W R526 1-216-805-11 METAL CHIP 47 5% 1/10W R527 1-216-805-11 METAL CHIP 47 5% 1/10W R528 1-216-833-11 METAL CHIP 10K 5% 1/10W R529 1-216-833-11 METAL CHIP 10K 5% 1/10W R530 1-216-809-11 METAL CHIP 100 5% 1/10W R531 1-216-864-11 SHORT CHIP 0 R532 1-216-821-11 METAL CHIP 1K 5% 1/10W R533 1-216-818-11 METAL CHIP 560 5% 1/10W R534 1-218-874-11 METAL CHIP 13K 0.5% 1/10W R537 1-216-821-11 METAL CHIP 1K 5% 1/10W R538 1-216-809-11 METAL CHIP 100 5% 1/10W R539 1-216-809-11 METAL CHIP 100 5% 1/10W ETHER www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 64 HCD-CZ1/NAS-CZ1 R540 1-216-809-11 METAL CHIP 100 5% 1/10W R541 1-216-809-11 METAL CHIP 100 5% 1/10W R542 1-216-797-11 METAL CHIP 10 5% 1/10W R545 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R546 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R548 1-216-833-11 METAL CHIP 10K 5% 1/10W R551 1-216-864-11 SHORT CHIP 0 R552 1-216-833-11 METAL CHIP 10K 5% 1/10W R553 1-216-833-11 METAL CHIP 10K 5% 1/10W R554 1-216-864-11 SHORT CHIP 0 R559 1-216-805-11 METAL CHIP 47 5% 1/10W R561 1-216-805-11 METAL CHIP 47 5% 1/10W R571 1-218-285-11 METAL CHIP 75 5% 1/10W R572 1-218-285-11 METAL CHIP 75 5% 1/10W R573 1-218-285-11 METAL CHIP 75 5% 1/10W R574 1-218-285-11 METAL CHIP 75 5% 1/10W < TRANSFORMER > T501 1-443-224-11 TRANSFORMER, PULSE < VIBRATOR > X501 1-795-807-11 VIBRATOR, CRYSTAL (25MHz) X502 1-795-692-11 QUARTZ CRYSTAL UNIT (24.576MHz) X503 1-795-535-21 VIBRATOR, CRYSTAL (11.2896Hz) ************************************************************ A-1099-012-A FL BOARD, COMPLETE ********* < CAPACITOR > C1001 1-162-306-11 CERAMIC 0.01uF 20% 16V C1002 1-162-282-31 CERAMIC 100PF 10% 50V C1003 1-162-282-31 CERAMIC 100PF 10% 50V C1006 1-124-261-00 ELECT 10uF 20% 50V C1007 1-124-222-91 ELECT 22uF 20% 6.3V C1008 1-162-960-11 CERAMIC CHIP 220PF 10% 50V C1011 1-162-306-11 CERAMIC 0.01uF 20% 16V C1023 1-162-286-31 CERAMIC 220PF 10% 50V C1024 1-162-286-31 CERAMIC 220PF 10% 50V C1025 1-162-286-31 CERAMIC 220PF 10% 50V C1026 1-162-286-31 CERAMIC 220PF 10% 50V C1027 1-162-286-31 CERAMIC 220PF 10% 50V C1028 1-162-286-31 CERAMIC 220PF 10% 50V C1029 1-162-286-31 CERAMIC 220PF 10% 50V C1030 1-162-286-31 CERAMIC 220PF 10% 50V C1031 1-162-286-31 CERAMIC 220PF 10% 50V C1032 1-162-286-31 CERAMIC 220PF 10% 50V C1033 1-162-286-31 CERAMIC 220PF 10% 50V C1034 1-162-286-31 CERAMIC 220PF 10% 50V C1035 1-162-286-31 CERAMIC 220PF 10% 50V C1036 1-162-286-31 CERAMIC 220PF 10% 50V C1037 1-162-286-31 CERAMIC 220PF 10% 50V C1038 1-162-286-31 CERAMIC 220PF 10% 50V < CONNECTOR > CN1001 1-784-735-11 CONNECTOR, FFC 13P < FLUORESCENT INDICATOR TUBE > FL1001 1-519-765-11 INDICATOR TUBE, FLUORESCENT < IC > IC1001 6-706-605-01 IC M66005-0151AHP IC1011 6-600-309-01 IC RPM7240-H9 < TRANSISTOR > Q1001 8-729-120-28 TRANSISTOR 2SC1623-L5L6 < RESISTOR > R1001 1-249-441-11 CARBON 100K 5% 1/4W R1002 1-216-821-11 METAL CHIP 1K 5% 1/10W R1003 1-216-821-11 METAL CHIP 1K 5% 1/10W R1004 1-216-821-11 METAL CHIP 1K 5% 1/10W R1005 1-216-821-11 METAL CHIP 1K 5% 1/10W R1006 1-216-833-11 METAL CHIP 10K 5% 1/10W R1007 1-249-441-11 CARBON 100K 5% 1/4W R1008 1-249-417-11 CARBON 1K 5% 1/4W ************************************************************ FRONT PANEL BOARD ****************** < CAPACITOR > C1202 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V C1211 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V C1212 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V C1213 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V C1214 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V C1215 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V C1251 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V C1252 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V < CONNECTOR > CN1201 1-793-580-11 CONNECTOR, FFC (LIF (NON-Z1F)) 15P CN1202 1-784-859-21 CONNECTOR, FFC (LIF (NON-ZIF)) 7P < LED > D1201 6-501-146-01 LED QSMN-C186 (1) D1202 6-501-146-01 LED QSMN-C186 (2) D1203 6-501-146-01 LED QSMN-C186 (3) D1204 6-501-146-01 LED QSMN-C186 (4) D1205 6-501-146-01 LED QSMN-C186 (5) D1251 8-719-064-07 LED SML-310LTT86 (I/1) < JUMPER RESISTOR > JR1201 1-216-296-11 SHORT CHIP 0 JR1202 1-216-296-11 SHORT CHIP 0 JR1203 1-216-296-11 SHORT CHIP 0 JR1204 1-216-296-11 SHORT CHIP 0 JR1205 1-216-296-11 SHORT CHIP 0 JR1206 1-216-296-11 SHORT CHIP 0 < TRANSISTOR > Q1201 8-729-027-43 TRANSISTOR DTC114EKA-T146 FL FRONT PANEL ETHER www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 65 HCD-CZ1/NAS-CZ1 Q1202 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q1203 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q1204 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q1205 8-729-027-43 TRANSISTOR DTC114EKA-T146 < RESISTOR > R1216 1-216-820-11 METAL CHIP 820 5% 1/10W R1217 1-216-820-11 METAL CHIP 820 5% 1/10W R1218 1-216-820-11 METAL CHIP 820 5% 1/10W R1219 1-216-820-11 METAL CHIP 820 5% 1/10W R1220 1-216-820-11 METAL CHIP 820 5% 1/10W R1221 1-216-821-11 METAL CHIP 1K 5% 1/10W R1222 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R1223 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R1224 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R1251 1-216-821-11 METAL CHIP 1K 5% 1/10W R1252 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R1261 1-216-821-11 METAL CHIP 1K 5% 1/10W R1262 1-216-825-11 METAL CHIP 2.2K 5% 1/10W < SWITCH > S1201 1-771-105-11 SWITCH, TACTILE (1) S1202 1-771-105-11 SWITCH, TACTILE (2) S1203 1-771-105-11 SWITCH, TACTILE (3) S1204 1-771-105-11 SWITCH, TACTILE (4) S1205 1-771-105-11 SWITCH, TACTILE (5) S1251 1-771-105-11 SWITCH, TACTILE (I/1) S1252 1-771-105-11 SWITCH, TACTILE (FUNCTION) S1256 1-771-105-11 SWITCH, TACTILE (N) S1257 1-771-105-11 SWITCH, TACTILE (x) S1261 1-771-105-11 SWITCH, TACTILE (VOL.+) S1263 1-771-105-11 SWITCH, TACTILE (VOL.–) ************************************************************ A-1099-011-A MAIN BOARD, COMPLETE (AEP, UK) A-1106-721-A MAIN BOARD, COMPLETE (US) *********** < CAPACITOR > C600 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C601 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C602 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C603 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C604 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C605 1-124-261-00 ELECT 10uF 20% 50V C606 1-164-156-11 CERAMIC CHIP 0.1uF 25V C607 1-164-156-11 CERAMIC CHIP 0.1uF 25V C608 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C609 1-115-456-21 DOUBLE LAYER 0.22F 5.5V C610 1-164-156-11 CERAMIC CHIP 0.1uF 25V C611 1-164-156-11 CERAMIC CHIP 0.1uF 25V C612 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C613 1-126-963-11 ELECT 4.7uF 20% 50V C614 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C615 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C616 1-164-156-11 CERAMIC CHIP 0.1uF 25V C617 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C618 1-124-589-11 ELECT 47uF 20% 16V C620 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C621 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C622 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C623 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C624 1-164-156-11 CERAMIC CHIP 0.1uF 25V C626 1-126-916-11 ELECT 1000uF 20% 6.3V C628 1-136-497-81 FILM 0.1uF 5% 50V C629 1-126-934-11 ELECT 220uF 20% 16V C630 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C631 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C632 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C633 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C634 1-126-767-11 ELECT 1000uF 20% 16V C635 1-104-665-11 ELECT 100uF 20% 25V C640 1-126-934-11 ELECT 220uF 20% 16V C651 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C661 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C700 1-104-665-11 ELECT 100uF 20% 25V C701 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C702 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C703 1-104-665-11 ELECT 100uF 20% 25V C704 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C705 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C706 1-104-665-11 ELECT 100uF 20% 25V C707 1-112-097-11 ELECT 2.2uF 20% 50V C708 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C710 1-112-097-11 ELECT 2.2uF 20% 50V C712 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C713 1-104-665-11 ELECT 100uF 20% 25V C714 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C717 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C752 1-126-933-11 ELECT 100uF 20% 16V C800 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C801 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C802 1-136-157-00 FILM 0.022uF 5% 50V C803 1-136-157-00 FILM 0.022uF 5% 50V C804 1-126-964-11 ELECT 10uF 20% 50V C805 1-130-479-00 MYLAR 0.0047uF 5% 50V C806 1-136-161-00 FILM 0.047uF 5% 50V C807 1-136-157-00 FILM 0.022uF 5% 50V C808 1-136-157-00 FILM 0.022uF 5% 50V C809 1-124-261-00 ELECT 10uF 20% 50V C810 1-124-261-00 ELECT 10uF 20% 50V C811 1-124-261-00 ELECT 10uF 20% 50V C812 1-124-261-00 ELECT 10uF 20% 50V C813 1-124-584-00 ELECT 100uF 20% 10V C814 1-124-261-00 ELECT 10uF 20% 50V C815 1-126-964-11 ELECT 10uF 20% 50V C816 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C817 1-112-084-11 ELECT 470uF 20% 16V C818 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C860 1-126-160-11 ELECT 1uF 20% 50V C900 1-126-964-11 ELECT 10uF 20% 50V C901 1-124-261-00 ELECT 10uF 20% 50V C902 1-136-157-00 FILM 0.022uF 5% 50V C903 1-136-157-00 FILM 0.022uF 5% 50V C904 1-130-479-00 MYLAR 0.0047uF 5% 50V C905 1-136-161-00 FILM 0.047uF 5% 50V FRONT PANEL MAIN www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 66 HCD-CZ1/NAS-CZ1 C906 1-136-157-00 FILM 0.022uF 5% 50V C907 1-136-157-00 FILM 0.022uF 5% 50V C908 1-136-161-00 FILM 0.047uF 5% 50V C909 1-126-964-11 ELECT 10uF 20% 50V C910 1-124-261-00 ELECT 10uF 20% 50V C911 1-124-261-00 ELECT 10uF 20% 50V C912 1-124-261-00 ELECT 10uF 20% 50V C913 1-124-261-00 ELECT 10uF 20% 50V < CONNECTOR > CN600 1-784-929-11 PIN, CONNECTOR 14P CN601 1-784-776-11 CONNECTOR, FFC 15P CN602 1-784-774-11 CONNECTOR, FFC 13P CN605 1-779-275-11 CONNECTOR, FFC (LIF (NON-ZIF)) 7P CN650 1-784-737-11 CONNECTOR, FFC 15P CN651 1-573-847-11 CONNECTOR, BOARD TO BOARD 15P CN700 1-779-564-21 CONNECTOR, FFC (LIF (NON-ZIF)) 27P CN751 1-568-828-11 CONNECTOR SOCKET 9P (US) CN751 1-568-830-11 CONNECTOR SOCKET 11P (AEP, UK) < DIODE > D600 8-719-058-24 DIODE RB501V-40TE-17 D601 8-719-988-61 DIODE 1SS355TE-17 D602 8-719-988-61 DIODE 1SS355TE-17 D603 8-719-988-61 DIODE 1SS355TE-17 D604 8-719-988-61 DIODE 1SS355TE-17 D605 8-719-988-61 DIODE 1SS355TE-17 D606 8-719-988-61 DIODE 1SS355TE-17 D607 8-719-988-61 DIODE 1SS355TE-17 D608 8-719-988-61 DIODE 1SS355TE-17 D609 8-719-988-61 DIODE 1SS355TE-17 D613 8-719-210-33 DIODE EC10DS2 D621 8-719-988-61 DIODE 1SS355TE-17 D650 8-719-210-33 DIODE EC10DS2 D651 8-719-210-33 DIODE EC10DS2 < EARTH TERMINAL > EPT701 1-537-738-21 TERMINAL, GROUND < FERRITE BEAD/JUMPER RESISTOR > FB600 1-414-813-11 FERRITE, EMI (SMD) (2012) FB601 1-216-295-00 SHORT CHIP 0 FB602 1-216-295-00 SHORT CHIP 0 FB603 1-216-295-00 SHORT CHIP 0 FB611 1-500-245-11 FERRITE, EMI (SMD) (2012) FB612 1-216-295-00 SHORT CHIP 0 FB613 1-216-295-00 SHORT CHIP 0 FB614 1-216-295-00 SHORT CHIP 0 FB615 1-500-245-11 FERRITE, EMI (SMD) (2012) FB616 1-500-245-11 FERRITE, EMI (SMD) (2012) FB700 1-216-864-11 SHORT CHIP 0 FB701 1-216-864-11 SHORT CHIP 0 FB702 1-216-864-11 SHORT CHIP 0 FB703 1-216-864-11 SHORT CHIP 0 FB704 1-414-813-11 FERRITE, EMI (SMD) (2012) FB705 1-414-813-11 FERRITE, EMI (SMD) (2012) FB706 1-414-813-11 FERRITE, EMI (SMD) (2012) FB707 1-414-813-11 FERRITE, EMI (SMD) (2012) FB750 1-216-864-11 SHORT CHIP 0 FB751 1-216-864-11 SHORT CHIP 0 FB801 1-216-864-11 SHORT CHIP 0 FB802 1-216-864-11 SHORT CHIP 0 FB803 1-216-864-11 SHORT CHIP 0 < IC > IC601 6-804-471-01 IC uPD703261YGF-S06-JBT-A IC602 6-701-680-01 IC PST3629NR IC603 8-759-649-50 IC SN74AHC1GU04DCKR * IC604 6-702-184-01 IC NJM2870F38 (TE2) IC650 6-702-771-01 IC TA78033LS IC701 6-703-650-11 IC M61529FP-D60G < COIL > L751 1-412-537-31 INDUCTOR 100uH < TRANSISTOR > Q600 8-729-027-23 TRANSISTOR DTA114EKA-T146 Q601 8-729-120-28 TRANSISTOR 2SC1623-L5L6 Q602 8-729-120-28 TRANSISTOR 2SC1623-L5L6 Q603 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q604 8-729-027-23 TRANSISTOR DTA114EKA-T146 Q605 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q606 8-729-120-28 TRANSISTOR 2SC1623-L5L6 Q607 8-729-027-23 TRANSISTOR DTA114EKA-T146 Q731 8-729-107-43 TRANSISTOR 2SC3624-L18 Q761 8-729-107-43 TRANSISTOR 2SC3624-L18 Q831 8-729-107-43 TRANSISTOR 2SC3624-L18 Q860 8-729-027-23 TRANSISTOR DTA114EKA-T146 Q861 8-729-107-43 TRANSISTOR 2SC3624-L18 Q862 8-729-027-43 TRANSISTOR DTC114EKA-T146 < RESISTOR > R602 1-216-833-11 METAL CHIP 10K 5% 1/10W R603 1-216-809-11 METAL CHIP 100 5% 1/10W R604 1-216-821-11 METAL CHIP 1K 5% 1/10W R605 1-216-809-11 METAL CHIP 100 5% 1/10W R606 1-216-809-11 METAL CHIP 100 5% 1/10W R607 1-216-821-11 METAL CHIP 1K 5% 1/10W R609 1-216-821-11 METAL CHIP 1K 5% 1/10W R610 1-216-809-11 METAL CHIP 100 5% 1/10W R611 1-216-809-11 METAL CHIP 100 5% 1/10W R612 1-216-809-11 METAL CHIP 100 5% 1/10W R613 1-216-809-11 METAL CHIP 100 5% 1/10W R614 1-216-809-11 METAL CHIP 100 5% 1/10W R615 1-216-809-11 METAL CHIP 100 5% 1/10W R618 1-216-853-11 METAL CHIP 470K 5% 1/10W R619 1-216-805-11 METAL CHIP 47 5% 1/10W R620 1-216-805-11 METAL CHIP 47 5% 1/10W R622 1-216-841-11 METAL CHIP 47K 5% 1/10W R623 1-216-841-11 METAL CHIP 47K 5% 1/10W R624 1-216-809-11 METAL CHIP 100 5% 1/10W R626 1-216-809-11 METAL CHIP 100 5% 1/10W R627 1-216-821-11 METAL CHIP 1K 5% 1/10W R628 1-216-821-11 METAL CHIP 1K 5% 1/10W R629 1-216-809-11 METAL CHIP 100 5% 1/10W MAIN www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 67 HCD-CZ1/NAS-CZ1 R630 1-216-809-11 METAL CHIP 100 5% 1/10W R631 1-216-809-11 METAL CHIP 100 5% 1/10W R632 1-216-833-11 METAL CHIP 10K 5% 1/10W R633 1-216-813-11 METAL CHIP 220 5% 1/10W R634 1-216-809-11 METAL CHIP 100 5% 1/10W R635 1-216-809-11 METAL CHIP 100 5% 1/10W R636 1-216-809-11 METAL CHIP 100 5% 1/10W R637 1-216-809-11 METAL CHIP 100 5% 1/10W R638 1-216-821-11 METAL CHIP 1K 5% 1/10W R639 1-216-809-11 METAL CHIP 100 5% 1/10W R640 1-216-821-11 METAL CHIP 1K 5% 1/10W R641 1-216-841-11 METAL CHIP 47K 5% 1/10W R642 1-216-833-11 METAL CHIP 10K 5% 1/10W R644 1-216-821-11 METAL CHIP 1K 5% 1/10W (AEP, UK) R645 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R646 1-216-821-11 METAL CHIP 1K 5% 1/10W (US) R647 1-216-821-11 METAL CHIP 1K 5% 1/10W R648 1-216-821-11 METAL CHIP 1K 5% 1/10W (AEP, UK) R649 1-216-821-11 METAL CHIP 1K 5% 1/10W (US) R650 1-216-809-11 METAL CHIP 100 5% 1/10W R651 1-216-821-11 METAL CHIP 1K 5% 1/10W R652 1-216-845-11 METAL CHIP 100K 5% 1/10W R653 1-216-809-11 METAL CHIP 100 5% 1/10W R654 1-216-809-11 METAL CHIP 100 5% 1/10W R659 1-216-821-11 METAL CHIP 1K 5% 1/10W R660 1-216-833-11 METAL CHIP 10K 5% 1/10W R661 1-216-809-11 METAL CHIP 100 5% 1/10W R662 1-216-809-11 METAL CHIP 100 5% 1/10W R663 1-216-833-11 METAL CHIP 10K 5% 1/10W R664 1-216-833-11 METAL CHIP 10K 5% 1/10W R665 1-216-809-11 METAL CHIP 100 5% 1/10W R666 1-216-817-11 METAL CHIP 470 5% 1/10W R667 1-216-809-11 METAL CHIP 100 5% 1/10W R668 1-216-833-11 METAL CHIP 10K 5% 1/10W R669 1-216-841-11 METAL CHIP 47K 5% 1/10W R670 1-216-809-11 METAL CHIP 100 5% 1/10W R672 1-216-809-11 METAL CHIP 100 5% 1/10W R673 1-216-845-11 METAL CHIP 100K 5% 1/10W R674 1-216-845-11 METAL CHIP 100K 5% 1/10W R675 1-216-809-11 METAL CHIP 100 5% 1/10W R676 1-216-833-11 METAL CHIP 10K 5% 1/10W R677 1-216-841-11 METAL CHIP 47K 5% 1/10W (US) R679 1-216-829-11 METAL CHIP 4.7K 5% 1/10W (AEP, UK) R679 1-216-837-11 METAL CHIP 22K 5% 1/10W (US) R680 1-216-841-11 METAL CHIP 47K 5% 1/10W R681 1-216-841-11 METAL CHIP 47K 5% 1/10W R684 1-216-821-11 METAL CHIP 1K 5% 1/10W R685 1-216-821-11 METAL CHIP 1K 5% 1/10W R686 1-216-821-11 METAL CHIP 1K 5% 1/10W R687 1-216-809-11 METAL CHIP 100 5% 1/10W R688 1-216-809-11 METAL CHIP 100 5% 1/10W R689 1-216-809-11 METAL CHIP 100 5% 1/10W R690 1-216-809-11 METAL CHIP 100 5% 1/10W R691 1-216-809-11 METAL CHIP 100 5% 1/10W R697 1-216-809-11 METAL CHIP 100 5% 1/10W R698 1-216-809-11 METAL CHIP 100 5% 1/10W R699 1-216-809-11 METAL CHIP 100 5% 1/10W R700 1-216-809-11 METAL CHIP 100 5% 1/10W R701 1-216-821-11 METAL CHIP 1K 5% 1/10W R702 1-216-821-11 METAL CHIP 1K 5% 1/10W R703 1-216-809-11 METAL CHIP 100 5% 1/10W R704 1-216-833-11 METAL CHIP 10K 5% 1/10W R705 1-216-833-11 METAL CHIP 10K 5% 1/10W R706 1-216-833-11 METAL CHIP 10K 5% 1/10W R707 1-216-809-11 METAL CHIP 100 5% 1/10W R710 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R711 1-216-809-11 METAL CHIP 100 5% 1/10W R712 1-216-845-11 METAL CHIP 100K 5% 1/10W R721 1-216-809-11 METAL CHIP 100 5% 1/10W R722 1-216-845-11 METAL CHIP 100K 5% 1/10W R730 1-216-821-11 METAL CHIP 1K 5% 1/10W R731 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R732 1-216-821-11 METAL CHIP 1K 5% 1/10W R733 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R734 1-216-833-11 METAL CHIP 10K 5% 1/10W R735 1-216-833-11 METAL CHIP 10K 5% 1/10W R750 1-216-845-11 METAL CHIP 100K 5% 1/10W R751 1-216-821-11 METAL CHIP 1K 5% 1/10W R752 1-216-845-11 METAL CHIP 100K 5% 1/10W R753 1-216-821-11 METAL CHIP 1K 5% 1/10W R800 1-216-809-11 METAL CHIP 100 5% 1/10W R801 1-216-821-11 METAL CHIP 1K 5% 1/10W R802 1-216-841-11 METAL CHIP 47K 5% 1/10W R803 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R804 1-216-833-11 METAL CHIP 10K 5% 1/10W R851 1-216-833-11 METAL CHIP 10K 5% 1/10W R852 1-216-833-11 METAL CHIP 10K 5% 1/10W R853 1-216-821-11 METAL CHIP 1K 5% 1/10W R854 1-216-821-11 METAL CHIP 1K 5% 1/10W R860 1-216-845-11 METAL CHIP 100K 5% 1/10W R862 1-216-864-11 SHORT CHIP 0 R900 1-216-833-11 METAL CHIP 10K 5% 1/10W R901 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R902 1-216-841-11 METAL CHIP 47K 5% 1/10W R903 1-216-833-11 METAL CHIP 10K 5% 1/10W R950 1-216-821-11 METAL CHIP 1K 5% 1/10W R951 1-216-821-11 METAL CHIP 1K 5% 1/10W R952 1-216-833-11 METAL CHIP 10K 5% 1/10W R953 1-216-833-11 METAL CHIP 10K 5% 1/10W < VIBRATOR > X600 1-795-058-21 VIBRATOR, CERAMIC (5MHz) ************************************************************ MAIN www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 68 HCD-CZ1/NAS-CZ1 PSAMP BOARD ************* 1-533-217-41 HOLDER, FUSE < CAPACITOR > 0C1 1-113-925-11 CERAMIC 0.01uF 20% 250V C101 1-136-165-00 FILM 0.1uF 5% 50V C102 1-136-165-00 FILM 0.1uF 5% 50V C103 1-112-094-11 ELECT 2200uF 20% 35V C104 1-112-094-11 ELECT 2200uF 20% 35V C111 1-136-165-00 FILM 0.1uF 5% 50V C112 1-136-165-00 FILM 0.1uF 5% 50V C113 1-112-424-11 ELECT 4700uF 20% 25V C114 1-119-772-11 ELECT 47uF 20% 35V C115 1-124-234-00 ELECT 22uF 20% 16V C116 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C117 1-119-772-11 ELECT 47uF 20% 35V C118 1-124-234-00 ELECT 22uF 20% 16V C119 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C121 1-119-772-11 ELECT 47uF 20% 35V C122 1-124-234-00 ELECT 22uF 20% 16V C123 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C124 1-119-772-11 ELECT 47uF 20% 35V C125 1-124-234-00 ELECT 22uF 20% 16V C126 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C131 1-165-319-11 CERAMIC CHIP 0.1uF 50V C132 1-126-968-11 ELECT 100uF 20% 50V C133 1-165-319-11 CERAMIC CHIP 0.1uF 50V C134 1-124-261-00 ELECT 10uF 20% 50V C201 1-131-704-31 FILM 1uF 5% 50V C202 1-131-704-31 FILM 1uF 5% 50V C203 1-165-319-11 CERAMIC CHIP 0.1uF 50V C204 1-165-319-11 CERAMIC CHIP 0.1uF 50V C221 1-126-963-11 ELECT 4.7uF 20% 50V C223 1-162-956-11 CERAMIC CHIP 180PF 5% 50V C224 1-126-947-11 ELECT 47uF 20% 35V C225 1-164-156-11 CERAMIC CHIP 0.1uF 25V C226 1-164-156-11 CERAMIC CHIP 0.1uF 25V C229 1-164-156-11 CERAMIC CHIP 0.1uF 25V C230 1-164-156-11 CERAMIC CHIP 0.1uF 25V C231 1-165-319-11 CERAMIC CHIP 0.1uF 50V C232 1-165-319-11 CERAMIC CHIP 0.1uF 50V C243 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C251 1-162-960-11 CERAMIC CHIP 220PF 10% 50V C261 1-164-156-11 CERAMIC CHIP 0.1uF 25V C262 1-126-933-11 ELECT 100uF 20% 16V C263 1-126-967-11 ELECT 47uF 20% 50V C264 1-126-916-11 ELECT 1000uF 20% 6.3V C265 1-104-662-91 ELECT 22uF 20% 25V C266 1-164-156-11 CERAMIC CHIP 0.1uF 25V C267 1-165-319-11 CERAMIC CHIP 0.1uF 50V C268 1-165-319-11 CERAMIC CHIP 0.1uF 50V C321 1-126-963-11 ELECT 4.7uF 20% 50V C323 1-162-956-11 CERAMIC CHIP 180PF 5% 50V C324 1-126-947-11 ELECT 47uF 20% 35V C325 1-164-156-11 CERAMIC CHIP 0.1uF 25V C326 1-164-156-11 CERAMIC CHIP 0.1uF 25V C329 1-164-156-11 CERAMIC CHIP 0.1uF 25V C330 1-164-156-11 CERAMIC CHIP 0.1uF 25V C331 1-165-319-11 CERAMIC CHIP 0.1uF 50V C332 1-165-319-11 CERAMIC CHIP 0.1uF 50V C343 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C351 1-162-960-11 CERAMIC CHIP 220PF 10% 50V < CONNECTOR > CN1 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P * CN3 1-564-321-21 PIN, CONNECTOR (3.96mm PITCH) 2P CN101 1-691-765-11 PLUG (MICRO CONNECTOR) 3P CN102 1-691-768-11 PLUG (MICRO CONNECTOR) 6P CN103 1-784-929-11 PIN, CONNECTOR 14P CN201 1-691-766-11 PLUG (MICRO CONNECTOR) 4P CN202 1-784-776-11 CONNECTOR, FFC 15P < DIODE > D1 8-719-988-61 DIODE 1SS355TE-17 D101 8-719-500-56 DIODE D3SBA20 D111 8-719-975-85 DIODE ERB83-004 D112 8-719-975-85 DIODE ERB83-004 D113 8-719-975-85 DIODE ERB83-004 D114 8-719-975-85 DIODE ERB83-004 D131 6-500-522-11 DIODE 10EDB40-TA2B5 D132 6-500-522-11 DIODE 10EDB40-TA2B5 D133 6-500-522-11 DIODE 10EDB40-TA2B5 D134 6-500-522-11 DIODE 10EDB40-TA2B5 D135 8-719-083-71 DIODE UDZSTE-1730B D136 8-719-083-60 DIODE UDZSTE-174.7B D261 8-719-988-61 DIODE 1SS355TE-17 D821 8-719-988-61 DIODE 1SS355TE-17 < EARTH TERMINAL > EP1 1-537-738-21 TERMINAL, GROUND (US) EP101 1-537-738-21 TERMINAL, GROUND EP201 1-537-738-21 TERMINAL, GROUND EP202 1-537-738-21 TERMINAL, GROUND < FERRITE BEAD/JUMPER RESISTOR > FB111 1-410-397-21 FERRITE 1.1uH FB241 1-469-324-21 FERRITE, EMI (SMD) (2012) FB341 1-469-324-21 FERRITE, EMI (SMD) (2012) < IC > IC111 6-703-550-01 IC TA7809LS IC112 8-759-071-48 IC TA7807S IC113 6-703-546-01 IC TA7804LS IC114 6-703-546-01 IC TA7804LS IC201 8-759-333-24 IC LM1876TF < JACK > J201 1-794-702-11 JACK, HEADPHONE (ANALOG IN) J202 1-794-702-11 JACK, HEADPHONE (PHONES) < LINE FILTER > 0LF1 1-419-625-11 COIL, LINE FILTER PSAMP www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 69 HCD-CZ1/NAS-CZ1 < TRANSISTOR > Q1 8-729-120-28 TRANSISTOR 2SC1623-L5L6 Q131 8-729-209-60 TRANSISTOR 2SB1375 Q261 8-729-120-28 TRANSISTOR 2SC1623-L5L6 Q262 8-729-120-28 TRANSISTOR 2SC1623-L5L6 Q263 8-729-120-28 TRANSISTOR 2SC1623-L5L6 < RESISTOR > 0R2 1-219-237-11 SOLID 3.3M 20% 1/2W (US) R3 1-216-829-11 METAL CHIP 4.7K 5% 1/10W 0R111 1-219-122-11 FUSIBLE 0.33 5% 1/4W 0R131 1-217-641-00 FUSIBLE 4.7 5% 1/4W R132 1-249-421-11 CARBON 2.2K 5% 1/4W R133 1-216-833-11 METAL CHIP 10K 5% 1/10W R134 1-249-413-11 CARBON 470 5% 1/4W R135 1-249-413-11 CARBON 470 5% 1/4W R151 1-216-864-11 SHORT CHIP 0 R152 1-216-864-11 SHORT CHIP 0 R153 1-216-864-11 SHORT CHIP 0 R155 1-216-864-11 SHORT CHIP 0 R156 1-216-864-11 SHORT CHIP 0 R157 1-216-864-11 SHORT CHIP 0 R158 1-216-864-11 SHORT CHIP 0 R221 1-216-821-11 METAL CHIP 1K 5% 1/10W R222 1-216-839-11 METAL CHIP 33K 5% 1/10W R223 1-216-821-11 METAL CHIP 1K 5% 1/10W R224 1-216-838-11 METAL CHIP 27K 5% 1/10W R225 1-216-797-11 METAL CHIP 10 5% 1/10W R226 1-216-842-11 METAL CHIP 56K 5% 1/10W R227 1-260-320-11 CARBON 220 5% 1/2W R229 1-216-797-11 METAL CHIP 10 5% 1/10W R251 1-216-821-11 METAL CHIP 1K 5% 1/10W R252 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R261 1-216-842-11 METAL CHIP 56K 5% 1/10W R262 1-216-845-11 METAL CHIP 100K 5% 1/10W R263 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R264 1-216-837-11 METAL CHIP 22K 5% 1/10W R321 1-216-821-11 METAL CHIP 1K 5% 1/10W R322 1-216-839-11 METAL CHIP 33K 5% 1/10W R323 1-216-821-11 METAL CHIP 1K 5% 1/10W R324 1-216-838-11 METAL CHIP 27K 5% 1/10W R325 1-216-797-11 METAL CHIP 10 5% 1/10W R326 1-216-841-11 METAL CHIP 47K 5% 1/10W R327 1-260-320-11 CARBON 220 5% 1/2W R329 1-216-797-11 METAL CHIP 10 5% 1/10W R351 1-216-821-11 METAL CHIP 1K 5% 1/10W R352 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R823 1-260-319-51 CARBON 180 5% 1/2W < RELAY > 0RY1 1-755-467-11 RELAY (POWER) RY201 1-755-170-11 RELAY ************************************************************ SUBPS BOARD ************ < CONNECTOR > CN5 1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P CN115 1-564-704-11 PIN, CONNECTOR (SMALL TYPE) 2P < TRANSFORMER > 0T2 1-437-672-21 TRANSFORMER, POWER (US) 0T2 1-437-673-21 TRANSFORMER, POWER (AEP, UK) ************************************************************ TOP PANEL BOARD **************** < CAPACITOR > C1272 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V C1275 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V < CONNECTOR > CN1271 1-784-859-21 CONNECTOR, FFC (LIF (NON-ZIF)) 7P < LED > D1272 6-501-146-01 LED QSMN-C186 (NETWORK) < JUMPER RESISTOR > JL1272 1-216-864-11 SHORT CHIP 0 < TRANSISTOR > Q1272 8-729-027-43 TRANSISTOR DTC114EKA-T146 < RESISTOR > R1275 1-216-820-11 METAL CHIP 820 5% 1/10W R1277 1-216-825-11 METAL CHIP 2.2K 5% 1/10W < SWITCH > S1271 1-771-105-11 SWITCH, TACTILE (NETWORK) ************************************************************ PSAMP SUBPS TOP PANEL www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 70 HCD-CZ1/NAS-CZ1 MISCELLANEOUS ************** 201 1-500-386-11 FILTER, CLAMP (FERRITE CORE) 0203 1-777-071-83 CORD, POWER (AEP, UK) 0203 1-783-820-11 CORD, POWER (US) 204 1-693-669-11 TUNER PACK (TM-10CE) (AEP, UK) 204 1-693-672-11 TUNER PACK (TM-10U) (US) 253 1-469-854-11 CORE, FERRITE (AEP, UK) 0301 8-820-221-01 OPTICAL PICK-UP BLOCK KSM-213EDP/C2NP (Including spindle motor (M101), sled motor (M102)) 302 1-827-992-11 WIRE (FLAT TYPE) (16 CORE) 0F1 1-533-451-12 FUSE, GLASS TUBE (DIA. 5) (3.15A/125V) (US) 0F1 1-533-470-12 FUSE, GLASS TUBE (DIA. 5) (T3.15A/250V) (AEP, UK) 0F101 1-533-449-12 FUSE, GLASS TUBE (DIA. 5) (2A/125V) (US) 0F101 1-533-467-12 FUSE, GLASS TUBE (DIA. 5) (T1.6A/250V) (AEP, UK) 0F102 1-533-449-12 FUSE, GLASS TUBE (DIA. 5) (2A/125V) (US) 0F102 1-533-467-12 FUSE, GLASS TUBE (DIA. 5) (T1.6A/250V) (AEP, UK) S101 1-771-853-11 SWITCH, DETECTION (LIMIT) S601 1-692-960-11 SWITCH, PUSH (1 KEY) (DISC LID OPEN DETECT) SP101 1-826-072-11 LOUDSPEAKER (2.5 cm) (Rear Tweeter) (L-CH) SP102 1-826-071-11 LOUDSPEAKER (9 cm) (Woofer) (L-CH) SP103 1-826-072-11 LOUDSPEAKER (2.5 cm) (Front Tweeter) (L-CH) SP201 1-826-072-11 LOUDSPEAKER (2.5 cm) (Rear Tweeter) (R-CH) SP202 1-826-071-11 LOUDSPEAKER (9 cm) (Woofer) (R-CH) SP203 1-826-072-11 LOUDSPEAKER (2.5 cm) (Front Tweeter) (R-CH) 0T1 1-443-694-11 TRANSFORMER, POWER (AEP, UK) 0T1 1-443-695-11 TRANSFORMER, POWER (US) ************************************************************* ACCESSORIES ************ 1-478-814-11 COMMANDER, STANDARD (RM-ANP002) 1-754-059-12 ANTENNA, LOOP (AM) 0 1-770-019-51 ADAPTOR, CONVERSION PLUG (UK) 1-793-184-23 CONNECTOR (F TYPE ADAPTOR) (FM) 1-827-478-11 CORD, CONNECTION (LAN CABLE) 2-318-581-11 MANUAL, INSTRUCTION (ENGLISH) 2-318-581-21 MANUAL, INSTRUCTION (FRENCH, SPANISH) (AEP) 2-318-581-31 MANUAL, INSTRUCTION (GERMAN, DUTCH, ITALIAN) (AEP) 2-318-581-41 MANUAL, INSTRUCTION (SWEDISH, POLISH) (AEP) 2-592-381-11 MANUAL, INSTRUCTION (DANISH, FINNISH) (AEP) 2-592-381-21 MANUAL, INSTRUCTION (PORTUGUESE) (AEP) 2-592-381-31 MANUAL, INSTRUCTION (GREEK) (AEP) 2-592-381-41 MANUAL, INSTRUCTION (HUNGARIAN, CZECH) (AEP) 2-592-381-51 MANUAL, INSTRUCTION (SLOVAKIAN) (AEP) X-2059-876-1 CD-ROM ASSY (M-crew Server) Ref. No. Part No. Description Remark www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 71 HCD-CZ1/NAS-CZ1 MEMO www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 2 HCD-CZ1/NAS-CZ1 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 1.0 2005.05 New 1.1 2005.08 Addition of detail of “5.bdt ERR RATE mode” in the Test Mode (SPM-05056) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com