索尼SONY ECM-S930C音响电路原理图

分类:电子电工 日期: 点击:0
索尼SONY ECM-S930C音响电路原理图-0 索尼SONY ECM-S930C音响电路原理图-1 索尼SONY ECM-S930C音响电路原理图-2 索尼SONY ECM-S930C音响电路原理图-3 索尼SONY ECM-S930C音响电路原理图-4 索尼SONY ECM-S930C音响电路原理图-5 索尼SONY ECM-S930C音响电路原理图-6 索尼SONY ECM-S930C音响电路原理图-7

1 Ver 1.0 2001. 03 SERVICE MANUAL US Model Canadian Model E Model General Type Stereo (employing the X-Y stereo system), electret condenser microphone Microphone cord 2.2 mm dia. two core-shielded, OFC (Oxygen-free copper) cord with the gold-plated L-shaped stereo miniplug Length: Approx. 30 cm (11 7/8 inches) Dimensions Approx. 55 × 34 × 40 mm (W × H × D) (2 1/4 × 1 3/8 × 1 5/8 inches) (without the projecting parts) Mass Approx. 40 g (1 lb. 4 oz.) including battery and cord Supplied accessories Carrying case (1) Performance Frequency response 100 – 15,000 Hz Directivity Unidirectional × 2 (Directive angle: 90° or 120°) (switchable) Output impedance 2.2 kilohm ±30 % Sensitivity Open circuit output level *1 : –43 ±4 dB (7 mV) Difference between L and R channel sensitivity: Less than 3 dB Power requirements Lithium battery CR2025 Continuous lasting hours: Approx. 350 hours Plug-in power Maximum input sound pressure level *2 More than 110 dBSPL Dynamic range More than 84 dB Operating temperature range 0°C to 40°C (32°F to 104°F) *1 0 dB=1 V/Pa, 1,000 Hz (1 Pa=10 µbar=94 dBSPL) *2 1 % wave distortion is present at 1,000 Hz (0 dBSPL=2 × 10-5 Pa) Design and specifications are subject to change without notice. SPECIFICATIONS Sony Corporation Audio Entertainment Group General Engineering Dept. 9-927-989-11 2001C0400-1 © 2001. 3 ELECTRET CONDENSER MICROPHONE Notes on Chip Component Replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 2 ECM-S930C SECTION 1 GENERAL This section is extracted from instruction manual. A Installing the battery (See fig. A) 1 Open the battery compartment lid. 2 Place the CR2025 battery (not supplied) with the + side facing upward. Be sure to place the battery with polarity positioned correctly. Battery life The Sony CR2025 lithium battery (not supplied) gives continuous operation on the microphone for about 350 hours. When you turn the power on, the battery check indicator lights momentarily. When the battery becomes weak, the indicator lights dimly or does not light at all. In this case, replace the battery with a new one. (Sony CR2025 lithium battery (not supplied)). To avoid battery wear or leakage, be sure to turn the power off after using the microphone. When the battery compartment lid comes off 1 Hold down part A with a thumb so that it does not slide. 2 Insert one of the parts of A into the projecting part B of the battery compartment and then insert the other part while pressing toward the inside. Removing the battery (See fig. B) When to replace the battery When the power is turned on, the battery check indicator lights momentarily. When the battery become weak, the indicator remains dimly lit or does not light at all. In this case, replace the battery with Sony CR2025 lithium battery. Use of another battery may present a risk of fire or explosion. Under normal conditions of use, the battery will last approximately 350 hours. Notes on lithium battery • Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. • Wipe the battery with a dry cloth to assure good contact. • Be sure to observe the correct polarity when installing the battery. • Do not hold the battery with metallic tweezers. Doing so can cause a short-circuit. WARNING Battery may explode if mistreated. Do not recharge, disassemble or dispose of in fire. 1 2 B 1 2 + side pôle + lado + – side pôle – lado – Lithium battery CR2025 (not supplied) Pile au lithium CR2025 (non fournie) Pila de litio CR2025 (no suministrada) A B Parts Identification and Uses (See fig. D) 1 Directive angle switch Set the switch according to the sound source. 90˚: Use to pick up a relatively narrower sound source (instrumental solo, conversation, etc.), to provide a clear stereo sound image focused on target source. 120˚: Use to pick up a relatively wider sound source (orchestra, chorus, stage play, etc.), to provide a natural stereo sound image with full reality. The above are guidelines for selecting an appropriate angle. Although following these guidelines is encouraged, you can freely select either angle according to your own preference. Note If you switch the angle during recording, noise may occure. 2 Gold-plated triple-pole stereo miniplug Connect to the MIC jack of your recording equipment (video camera, etc.) 3 Battery compartment lid 4 Power switch ON: Select when the microphone works with the battery. OFF: Select when the microphone works with plug-in power or when you turn it off. When you use a Sony video camera with plug-in power system, set the power switch to OFF. 5 Battery check indicator When the power is turned on, this indicator lights momentarily. When the battery becomes weak, the indicator remains dimly lit or does not light at all. In this case, replace the battery with a new one. D 1 2 3 4 5 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 3 ECM-S930C SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 2-1. CASE, UPPER Note : When installing, fit the selection knob and awitch (SW1) (center position) 2-2. AMP BOARD Note : When installing, fit the power knob and awitch (SW2) 2-3. HOLDER ASSY, SHOE 2 4 case, upper 3 claw 1 B 1.7 lid, battery case knob, selection 4 AMP board grille grille knob, power 2 1 2 3 Removal the solder. 3 holder assy, shoe 2 case, lower 1 P 2.6x4 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 4 ECM-S930C SECTION 3 DIAGRAMS 3-1. PRINTED WIRING BOARD 1 A B C D E F G H I 2 3 4 5 6 7 AMP BOARD (CONDUCTOR SIDE) AMP BOARD (COMPONENT SIDE) R202 C202 R201 R101 R104 R204 C3 R3 C2 C4 C203 C103 C102 R2 SW1 (DIRECTIVE ANGLE) 120˚ 90˚ C201 R203 R1 C1 C101 R103 R102 -1 -2 D2 D1 SW2(POWER) ON OFF D3 ON BATTERY CHECK LAMP MICROPHONE CAPSULE(R CH) MIC201 Q201 S RED WHT GRY MICROPHONE CAPSULE(L CH) MIC101 Q101 S RED WHT GRY BLU RED MINI PLUG (MIC OUT) 1-679-165- 11 (11) 1-679-165- 11 (11) LITHIUM BATTERY CR-2025 3V www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 5 ECM-S930C 3-2. SCHEMATIC DIAGRAM (DIRECTIVE ANGLE) (POWER) (POWER) Note on Printed Wiring Boards: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • z : Through hole. • : Pattern from the side which enables seeing. Caution: Pattern face side: Parts on the pattern face side seen from (Conductor Side) the pattern face are indicated. Parts face side: Parts on the parts face side seen from (Component Side) the parts face are indicated. Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. • C : panel designation. • A : B+ Line. • Power voltage is dc 3 V and fed with regulated dc power supply from battery terminal. • Voltage is dc with respect to ground under no-signal (detuned) condition. • Voltages are taken with a VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal produc- tion tolerances. • Signal path. F : AUDIO www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 6 ECM-S930C SECTION 4 EXPLODED VIEWS Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark NOTE: • The mechanical parts with no reference number in the exploded views are not supplied. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • Accessories and packing materials are given in the last of this parts list. 1 2 3 4 1 5 6 7 8 9 10 11 12 14 13 15 12 11 16 18 17 19 20 20 Q201 Q101 MIC101 MIC201 21 22 21 22 * 1 3-222-928-01 HOLDER, UNIT * 2 1-679-165-11 AMP BOARD 3 3-224-339-02 SHEET, BATTERY 4 1-550-104-33 HOLDER, BATTERY 5 3-222-923-01 LID, BATTERY CASE 6 3-222-907-01 HINGE 7 3-222-926-01 KNOB, SELECTION 8 3-222-921-01 CASE, UPPER * 9 3-222-927-01 LEVER, SELECTION 10 3-686-420-01 SCREW (P1.4X2.5), TAPPING 11 3-222-929-01 GRILLE 12 3-222-930-01 SCREEN, GRILLE 13 3-222-922-01 CASE, LOWER 14 1-790-506-21 CORD, MICROPHONE (2 CORE) 15 X-3379-657-1 HOLDER ASSY, SHOE 16 3-222-925-01 KNOB, POWER 17 3-222-924-01 WINDOW, LED 18 3-318-203-94 SCREW (B1.7), TAPPING 19 7-621-259-25 SCREW +P 2.6X4 20 2-545-447-01 HOLDER, CAPSULE 21 2-523-713-00 TERMINAL * 22 2-532-219-00 TERMINAL, GROUND MIC101 8-814-289-90 CAPSULE, MICROPHONE CU14-03 (L-CH) MIC201 8-814-289-90 CAPSULE, MICROPHONE CU14-03 (R-CH) Q101 8-729-037-42 FET 2SK1578-A Q201 8-729-037-42 FET 2SK1578-A www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 7 ECM-S930C SECTION 5 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable • CAPACITORS uF : µF • COILS uH : µH • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark When indicating parts by reference number, please include the board. AMP * 1-679-165-11 AMP BOARD *********** 1-550-104-33 HOLDER, BATTERY < CAPACITOR > C1 1-127-573-11 CERAMIC CHIP 1uF 10% 16V C2 1-125-839-11 TANTAL. CHIP 47uF 20% 6.3V C3 1-164-505-11 CERAMIC CHIP 2.2uF 16V C4 1-125-839-11 TANTAL. CHIP 47uF 20% 6.3V C101 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C102 1-104-760-11 CERAMIC CHIP 0.047uF 10% 50V C103 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C201 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C202 1-104-760-11 CERAMIC CHIP 0.047uF 10% 50V C203 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V < DIODE > D1 8-719-049-09 DIODE 1SS367-T3SONY D2 8-719-072-95 DIODE 015AZ3.9-X-TPL3 D3 8-719-052-72 LED CL-220HR-C (ON) < RESISTOR > R1 1-216-832-11 METAL CHIP 8.2K 5% 1/16W R2 1-216-813-11 METAL CHIP 220 5% 1/16W R3 1-216-833-11 METAL CHIP 10K 5% 1/16W R101 1-216-994-11 RES-CHIP 13K 5% 1/16W R102 1-216-817-11 METAL CHIP 470 5% 1/16W R103 1-216-817-11 METAL CHIP 470 5% 1/16W R104 1-216-828-11 METAL CHIP 3.9K 5% 1/16W R201 1-216-994-11 RES-CHIP 13K 5% 1/16W R202 1-216-817-11 METAL CHIP 470 5% 1/16W R203 1-216-817-11 METAL CHIP 470 5% 1/16W R204 1-216-828-11 METAL CHIP 3.9K 5% 1/16W < SWITCH > SW1 1-762-741-11 SWITCH, SLIDE (DIRECTIVE ANGLE) SW2 1-572-018-11 SWITCH, SLIDE (POWER) ************************************************************* MISCELLANEOUS *************** 14 1-790-506-21 CORD, MICROPHONE (2 CORE) MIC101 8-814-289-90 CAPSULE, MICROPHONE CU14-03 (L-CH) MIC201 8-814-289-90 CAPSULE, MICROPHONE CU14-03 (R-CH) Q101 8-729-037-42 FET 2SK1578-A Q201 8-729-037-42 FET 2SK1578-A ************************************************************* ACCESSORIES & PACKING MATERIALS ******************************** 3-229-590-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH, SPANISH) 3-926-629-03 POUCH, CARRYING www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com 8 ECM-S930C REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 1.0 2001. 03 New www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com

标签:

版权声明

1. 本站所有素材,仅限学习交流,仅展示部分内容,如需查看完整内容,请下载原文件。
2. 会员在本站下载的所有素材,只拥有使用权,著作权归原作者所有。
3. 所有素材,未经合法授权,请勿用于商业用途,会员不得以任何形式发布、传播、复制、转售该素材,否则一律封号处理。
4. 如果素材损害你的权益请联系客服QQ:77594475 处理。