NS405/NS410/NS415
RMT-D141A/D142A/D142O/D142P
US Model
Canadian Model
DVP-NS315/NS415
AEP Model
DVP-NS305/NS310/NS405/NS410
UK Model
DVP-NS305/NS405
Russian Model
Hong Kong Model
Korea Model
Taiwan Model
Saudi Arabia Model
GA Model
Indian Model
Pakistan Model
Malaysia Model
DVP-NS305
Middle East Model
Oceania Model
DVP-NS305/NS415
PX Model
Mexico Model
Latin Model
Argentina Model
Brazilian Model
DVP-NS315
SERVICE MANUAL
CD/DVD PLAYER
System
Laser: Semiconductor laser
Signal format system: NTSC/PAL
Audio characteristics
Frequency response: DVD VIDEO (PCM
96 kHz): 2 Hz to 44 kHz (±1.0 dB)/DVD
VIDEO (PCM 48 kHz): 2 Hz to 22 kHz
(±0.5 dB)/CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio (S/N ratio): 115 dB
(LINE OUT (L/R) AUDIO jacks only)
Harmonic distortion: 0.003 %
Dynamic range: DVD VIDEO: 103 dB/CD:
99 dB
Wow and flutter: Less than detected value
(±0.001% W PEAK)
The signals from LINE OUT L/R (AUDIO)
jacks are measured. When you play PCM
sound tracks with a 96 kHz sampling
frequency, the output signals from the
DIGITAL OUT (OPTICAL or COAXIAL)
jack are converted to 48 kHz sampling
frequency.
Outputs/Inputs
(Jack name: Jack type/Output or Input level/
Load impedance)
LINE IN (AUDIO)*: Phono jack/–/47
kilohms (DVP-NS315/NS415)
(DVP-NS315/NS415)
Outputs (DVP-NS305/NS310/NS405/NS410)
LINE OUT (AUDIO): Phono jack/2 Vrms/
Over 10 kilohms
DIGITAL OUT (OPTICAL)*: Optical
output jack/–18 dBm (wave length:
660 nm)
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT(Y, PB, PR):
Phono jack/Y: 1.0 Vp-p/PB, PR: 0.7 Vp-p/
75 ohms (DVP-NS315/NS415)
(DVP-NS315/NS415)
LINE IN (VIDEO)*: Phono jack/1.0 Vp-p/
75 ohms
LINE OUT (VIDEO): Phono jack/1.0 Vp-p/
75 ohms
S VIDEO OUT: 4-pin mini DIN/Y:
1.0 Vp-p, C: 0.286 Vp-p/75 ohms
* DVP-NS405/NS410/NS415 only
General
Power requirements: 120 V AC, 60 Hz/
110 to 240V AC, 50/60 Hz
See page 1-1 for further information.
Power consumption: 12 W/13 W
See page 1-1 for further information.
Dimensions (approx.): 430 × 62 × 255 mm
(17 × 2 1/2 × 10 1/8 in.) (width/height/
depth) incl. projecting parts
Mass (approx.): 2.3 kg (5 5/64 lb)
Operating temperature: 5 ° C to 35 ° C
(41 °F to 95 °F)
Operating humidity: 25 % to 80 %
Supplied accessories
See page 1-3.
Specifications and design are subject to
change without notice.
ENERGY STARR is a U.S. registered mark.
As an ENERGY STARR Partner, Sony
Corporation has determined that this product
meets the ENERGY STARR guidelines for
energy efficiency.
(To change the color system)
SPECIFICATIONS
Photo : DVP-NS415
RMT-D142A
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
DVP-NS305/NS310/NS315/NS405/NS410/NS415
SECTION 3
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM
3-1
3-2
IC201
IC301
IC403
IC303
IC101
IC601
IC404
IC404
IC102
J104 (1/2)
J101 (2/2)
J103
CN103
IC202
BASE UNIT
KHM-270AAA/J1RP
MS-81 BOARD
(SEE PAGE 4-17)
MB-103 BOARD
(SEE PAGE 4-15 to 4-28)
AV-61 BOARD
(SEE PAGE 4-31 to 4-34)
IF-89 BOARD
(SEE PAGE 4-9)
OPTICAL DEVICE
DVD/CD
PD IC
RF
DVD/CD RF AMP,
DIGITAL SERVO
RF+
ARP,
SERVO DSP
FOCUS
COIL
TRACKING
COIL
FOCUS/TRACKING
COIL DRIVE,
SPINDLE/SLED/
LOADING
MOTOR DRIVE
M
M
M
SPINDLE
MOTOR
SLED
MOTOR
M001
LOADING
MOTOR
FUNCTION
KEY
ND401
FLUORESCENT
INDICATOR TUBE
IF COM
P CON
POWER
SERIAL BUS
EEPROM
PARALLEL BUS
CDDOUT, CDDATA,
CDBCK, CDLRCK
SDI 0 – 7
AV DECODER
SPDIF, ACH12,
ACH34, ACH56,
BCK, LRCK
16M DRAM
16M SDRAM
V, Y, C
Y, Cb, Cr
VIDEO
BUFFER
SPDIF
IC204
AUDIO
D/A CONVERTER
IC201
AUDIO
AMP
EVER+3.3V
+11V
+5V
SW+3.3V
+1.8V
SW+3.3V
+5V
SW+11V
EVER–13V
INLIMIT
SENSOR
CHUCK/TRAY
DETECT
SWITCHING REGULATOR
(SRV1246JUC)
(SEE PAGE 4-37)
SWITCHING
REG
AC IN
16
LINE OUT
VIDEO 1
VIDEO 2
S VIDEO OUT
L
R
LINE OUT
AUDIO 2
L
R
AUDIO 1
OPTICAL
DIGITAL
OUT
COAXIAL
J201
D101-104
F101
2A
100V 50/60Hz
AI+5V
EVER+3.3V
AU+11V
SW–13V
REG
IC104
IC403
SYSTEM
CONTROL
S001
D1 VIDEO
OUT
AU+5V
REG
IC106
FLASH
MEMORY
SW801
POWER
w w w
.
x i a o y u 1 6 3 .
c o m
Q Q
3 7 6 3 1 5 1 5 0
9
9
2
8
9
4
2
9
8
T E L
1 3 9 4 2 2 9 6 5 1 3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
DVP-NS305/NS310/NS315/NS405/NS410/NS415
3-3
3-4
3-2. RF/SERVO BLOCK DIAGRAM
2
19
25
27
59
42
41
36
38
44
13
15
21
33
37
14
ı
11
7
ı
10
45
ı
48
32
ı
29
125
124
126
147
131
148
152
15
ı
18
37
36
21
22
48
1
47
46
20
22
15
17
35
34
27
28
7
10
25
24
3
4
45
5
128
153
154
146
61
12
11
143 144
32 33
MB-103 BOARD (1/4)
(SEE PAGE 4-15, 17, 19)
BASE UNIT
KHM-250AAA/J1RP
OPTICAL DEVICE
24
25
17
16
22
20
13
8
6
12
4
3
15
23
18
26
2
1
Q201
DVD LD DRIVE
IC201
IC301
DVD/CD
PD IC
DVD/CD
LD MODULE
CN203
DVD/CD RF AMP,
DIGITAL SERVO
RF IN
A – D
E – H
A2 – D2
VC
DVDPD
CDPD
DVD LD
SIGO
FE
TE
PI
DFT
MON
MIRR
TZC
SRD
SWD
SCLK
SDEN
SERVO DSP
ADC1
ADC0
ADC2
DFCTI
ADC7
POM 2, 3
129
130 ADC5, 6
MIRR
TZC
ADC4
SIGNAL PROCESSOR
(SEE PAGE 3-5)
SYSTEM CONTROL
(SEE PAGE 3-7)
XRESET
HCS
HINT
MDSO
MDPO
163 164
GIO9/FGREF
GIO10/FGIN
GIO1/INT3
PWM2
PWM0, 1
POM 0, 1
GIO0/INT2
SPINDLE
MOTOR
DRIVE
FOCUS
COIL
DRIVE
TRACKING
COIL
DRIVE
LOADING
MOTOR
DRIVE
SLED
MOTOR
DRIVE
7
1
ı
4
9
8
1
5
4
IC202
5
2
4
1
2
CN402
CN001
LDM±
CKSW1
OCSW1
INLIMIT
SENSOR
TRACKING
COIL
FOCUS
COIL
M001
LOADING
MOTOR
M
M
M
MS-81 BOARD (SEE PAGE 4-17)
SLED
MOTOR
SPINDLE
MOTOR
CN204
39
VCI
19
39
20
22
16
17
155
GIO2/INT4
16
CHUCK/TRAY
DETECT
S001
(1/2)
RF
A – D
E – H
VC
PD
DVD LD
26
Q202
CD LD DRIVE
CD LD
CD LD
VR
SLA±, SLB±
SPM±
INLIM
TRK±
127 ADC3
FCS±
PS
TSD-M
40
42
43
VREF
+3.3V
LDON
159
161
162
167
GIO6/SDI
GIO7/SDO
GIO8/SCK
GIO13
XSDPIT
XSDPCS
XRST
XDRVMUTE
OCSW1
RF+
CKSW1
XLDON
FE
TE
PI
SSDFCTI
SS MON
MDSO, MDPO
SPMUTE
SLDA, SLDB
LMP, LMM
TSD
LMCTL
TDRV±
FDRV±
SPFG
SLE
640mVp-p
0.2usec/div
40usec/div
6 CN202 1 (DVD PB)
6 CN202 1 (CD PB)
440mVp-p
7 CN202 3
(DVD PLAY)
210mVp-p
20ms/div
7 CN202 3
(CD PLAY)
210mVp-p
20ms/div
8 CN202 4
(DVD PLAY)
1.9Vp-p
40ms/div
8 CN202 4
(CD PLAY)
1.8Vp-p
200ms/div
w w w
.
x i a o y u 1 6 3 .
c o m
Q Q
3 7 6 3 1 5 1 5 0
9
9
2
8
9
4
2
9
8
T E L
1 3 9 4 2 2 9 6 5 1 3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
DVP-NS305/NS310/NS315/NS405/NS410/NS415
3-5
3-6
3-3. SIGNAL PROCESSOR BLOCK DIAGRAM
SDCK, XSHD,
XSRQ, XSAK, SDEF
SDCK
XSHD
XSRQ
XSAK
SDEF
DATA
BCLK
LRCK
DOUT
CDIN2I
CDIN1I
CDBCKI
CDLRKI
ICLKI
IERRI
ISTARTI
IVALI
IREQO
111
113
24
25
26
27
28
150
196
197
207
22
70
24
25
63
55
65
61
59
57
26
28
29
166
167
158
160
134
ı
141
2
ı
9
37
ı
40
42
ı
45
169
170
175
56
57
ı
59
63
64
47
ı
51
77
ı
84
65 – 74
MEMA 0 – 9
MEMD 0 – 15
ADAD 0 – 11
ADDT 0 – 15
105-108 110-113
115 116 118 120
135-138 140-143
145-148 150
151 153 154
168-169
171-174
176-179
181-184
186-189
191-194
2 – 5
7 – 10
12 – 15
17 – 20
122 124 125
127 129 130
132 133
36 – 43
46 – 53
29 31
30
IC303
16M DRAM
IC301
ARP
IC403
AV DECODER
IC404
16M SDRAM
31
32
34
35
202 – 205
MB-98 BOARD (2/4)
(SEE PAGE 4-19 to 4-23)
RF+
RF/SERVO
(SEE PAGE 3-4)
SYSTEM CONTROL
(SEE PAGE 3-7)
16
RFIN1
RFIN2
SD 0 – 7
SDI 0 – 7
DTI 0 – 7
MA 0 – 9
MD 0 – 15
SDDQ 0 – 15
CDDATA, CDBCK,
CDLRCK, CDDOUT
CLK, CKE,
DQML, DQMU,
CS, WE,
CAS, RAS
WE, RAS
LCAS, UCAS
C OUT
Y OUT
COMPOUT
B OUT
R OUT
G OUT
C
Y
V
Cr/B
Cb/R
Y/G
COUT
YOUT
COMPOUT
CR/B
CB/R
Y/G
VIDEO
(SEE PAGE 3-9)
AUDIO
(SEE PAGE 3-11)
VREFI
ACH12
ACH34
ACH56
LAND
LRCKO
BCKO
ACH12
LRCK
BCK
VIDEO
LEVEL
ADJ
RV401
HD 0 – 15
HAD 0 – 21
HA 0 – 21
HD 0 – 15
D 0 – 7
A 0 – 7
HA 0 – 7
HD 8 – 15
XRD
XWRH
RSTn
DM ACK1
DM REQ1
DM ACK0
DM REQ0
ACLK
HAD23
HAD22
CLKI
SCLKI
200
199
HWAIT0n
HIREQ0
HA 0 – 21
HD 0 – 15
HA 0 – 21
HD 0 – 15
XRST
512FSAVD
33MARP
XWRH
XRD
TRST
XARPIT
XARPCS
XWAIT
XAVDCS2
XAVDCS3
27MAVD
XAVDIT
DREQ0
DACK0
DREQ1
DACK1
XWR
XRD
XINT
XCS
XWAT
CLKIN
30
DO
SPDIF
175
174
173
172
TDO
TCK
TDI
TMS
171
97
99
98
101
102
TRST
TDI
TCK
TDO
TMS
TRST
HCSn
HRWn
LAND
(FOR J TAG)
(2/2)
3
CN601 (1/3)
1
11
7
9
5
qj IC403 yd
850mVp-p
H
qd IC403 tg
H
950mVp-p
qk IC403 yg
1.1Vp-p
H
qh IC403 ya
650mVp-p
H
qg IC403 tl
650mVp-p
H
950mVp-p
H
qf IC403 tj
qs IC403 ws
4.8Vp-p
40.8nsec
ql IC403 key to go to the next item, or
. key to repeat the same check again.
Test Mode Menu
0. Syscon Diagnosis
1. Drive Auto Adjustment
2. Drive Manual Operation
3. Mecha Aging
4. Emargency Hisory
5. Version Information
6. Video Level Adjustment
Exit: Power Key
_
Model
: DPX-6xxxx
Revision : x.xxx
Last Off: xx
### Syscon Diagnosis ###
Check Menu
0. Quit
1. All
2. Version
3. Peripheral
4. Servo
5. Supply
6. AV Decoder
7. Video
8. Audio
_
### Syscon Diagnosis ###
Diag All Check
No. 2 Version
2-3. ROM Check Sum
Check Sum = 2005
Press NEXT Key to Continue
Press PREV key to Repeat
_
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-2
To quit the diagnosis and return to the Check Menu screen, press
x or [ENTER] key. If an error occurred, the diagnosis is suspended
and the error code is displayed as shown below.
Press x key to quit the diagnosis, or . key to repeat the
same item where an error occurred, or > key to continue the
check from the item next to faulty item.
Selecting [2] and subsequent items call the submenu screen of each
item. When “———” is displayed in the submenu, it means that
the test is not supported in the model.
For example, if “5. Supply” is selected, the following submenu
will be displayed.
0. (Quit)
Quit the submenu and return to the main menu.
1. (All submenu items continuous check.)
This menu checks 2 and subsequent items successively. At the item
where visual check is required for judgment or an error occurred,
the checking is suspended and the message is output for key entry.
Normally, all items are checked successively one after another
automatically unless an error is found.
Selecting [2] and subsequent items executes respective menus and
outputs the results.
For the contents of each submenu, see “General Description of
Checking Method” and “Check Items List”.
General Description of Checking Method
2. Version
(2-2) Revision
ROM revision number is displayed.
Error: Not detected.
The revision number defined in the source file is displayed
with four digits.
(2-3) ROM Check Sum
Check sum is calculated.
Error: Not detected.
8-bit data are added up to the ROM address 0x000F0000 to
0x002EFFFF, and the result is displayed with 4-digit hexa-
decimal number. Error is not detected. Compare the result
with the specified value.
(2-4) Model Type
Model code is displayed.
Error: Not detected.
The model code read from the EEPROM is displayed with
2-digit hexadecimal number.
(2-5) Region
Region code is displayed.
Error: Not detected.
The region code determined from the model code is dis-
played.
(2-6) M’t Check
Mount resistance is checked.
Error 22: The region code does not accord.
Check whether the region code that is deduced from model
resistance and destination resistance accords with the re-
gion code that is deduced from region resistance value.
3. Peripheral
(3-2) EEPROM Check
Data write t read, and accord check
Error 03: EEPROM write/read discord
0x9249, 0x2942 and 0x4294 are written to the address 0x00
to 0xFF of the EEPROM and then read for checking. Be-
fore writing, the data are saved, then after checking, they
are written to restore the contents of EEPROM.
(3-3) Gate Array Check (Machine only in which Gate Array is
installed)
Data write t read, and accord check
Error 02: Gate array write/read discord
Data of 0x00 to 0xFF is written sequentially to the address
0xF and then read for checking.
(3-4) HAND FLASH Check (HAND Flash installed model only)
Data clear t write t read, and accord check
Error 04: Clear error
05: Write error
06: Read data discord
21: Number of defective block exceeds 10.
Clear 0th block of flash memory and write. Then read for
checking.
When defective block exists, the address is displayed.
When the number of defective block exceeds 10, it is error.
(3-5) SACD Check (SACD Decoder installed model only)
Device reset t Built-in RAM check
Error 50: Write/read data discord
### Syscon Diagnosis ###
3-2. EEPROM Check
Error 03: EEPROM Write/Read N
Address
: 00000001
Write Data
: 2492
Read Data
: 2490
Press NEXT Key to Continue
Press PREV key to Repeat
_
### Syscon Diagnosis ###
Check Menu
No. 5 Supply
0. Quit
1. All
2. ARP Register Check
3. ARP to RAM Data Bus
4. ARP to RAM Address Bus
5. ARP RAM Check
_
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-3
(3-6)
Venc Check (Progressive support model only)
Data write t read, and accord check
Error: 52: Write/read data discord
Error may occur due to defect of access with syscon.
(3-7)
————— (Not supported)
(3-8)
External RAM Check (External RAM installed model only)
Test data write t read, and accord check
Error
Check the external RAM used in syscon.
4. Servo
(4-2)
Servo DSP Check
Data write t read, and accord check
Error 12: Read data discord
0x9249, 0x2942 and 0x4294 are written to the RAM ad-
dress 0x602 of the Servo DSP and then read for checking.
(4-3)
—————
Check no support.
(4-4)
RF Amp Register Check
Data write t read, and accord check
Error xx: RF Amp register write, and read data discord
Implement 8-bit shift operation of the xx to the readable/
writable register of the RF Amp. If once write data do not
accord with read data, it is NG.
5. Data Supply System
(5-2)
ARP Register Check
Data write t read, and accord check
Error 08: ARP register write, and read data discord
Data 0x00 to 0xFF is written sequentially to the ARP TMAX
register (address 0xC6) and then read for checking.
(5-3)
ARP to RAM Data Bus
Data write t read, and accord check
Error 09: ARP Tt RAM data bus error
Data 0x0001 to 0x8000 where one bit each is set to 1 are
written to the address 0 of RAM (IC303) connected to the
ARP (IC302) through the bus, then they are read and
checked. In case of discord, written bit pattern and read
data are displayed. If data where multiple bits are 1 are
read, the bits concerned may touch each other. Further, if
data where certain bit is always 1 or 0 regardless of written
data, the line could be disconnected or shorted.
(5-4)
ARP to RAM Address Bus
Data write t other address read discord check
Error 10: ARP Tt RAM address bus error
Caution: Address and data display in case of an error is
different from the display of other diagnosis (described
later).
Before starting the test, all addresses of RAM (IC303) are
cleared to 0x0000.
First, 0xA55A is written to the address 0x00000, and the
address data are read and checked from addresses 0x00001
to 0x80000 while shifting 1 bit each. Next, the data at that
address is cleared, and it is written to the address 0x00001,
and read and checked in the same manner. This check is
repeated up to the address 0x80000 while shifting the ad-
dress data by 1 bit each.
If data other than 0 is read at the addresses except written
address, an error is given because all addresses were al-
ready cleared to 0. In this check, the error display pattern is
different from that of other diagnosis; read data, written
address, and read address are displayed in this order. How-
ever, the message uses same template, and accordingly ex-
change Address and Data when reading. The following dis-
play, for example,
shows the data 0xA55A was read from address 0x00080000 though
it was written to the address 0x00000000. This implies that these
addresses are in the form of shadow. Also, if the read data is not
0xA55A, another error will be present.
(5-5)
ARP RAM Check
Data write t read, and accord check
Error 11: ARP RAM read data discord
The program code data stored in ROM are copied to all
areas of RAM (IC303) connected to the ARP through the
bus, then they are read and checked if they accord. If the
detail check was selected initially, the data are written to
all areas and read, then the same test is conducted once
again with the data where all bits are inverted between 1
and 0. If discord is detected, faulty address, written data,
and read data are displayed following the error code 11,
and the test is suspended.
### Syscon Diagnosis ###
5-4. ARP to RAM Address Bus
Error 10: ARP - RAM Address B
Address
: 0000A55A
Write Data
: 00000000
Read Data
: 00080000
Press NEXT Key to Continue
Press PREV key to Repeat
_
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-4
6. AV Decoder
(6-2) 1935 RAM
Data write t read, and accord check
Error 13: AVD RAM read data discord
The program code data stored in ROM (IC107) are copied
to all areas of RAM (IC504, IC505) connected to the AVD
through the bus, then they are read and checked if they ac-
cord. Further, the same test is conducted once again with
the data where all bits are inverted between 1 and 0. If dis-
cord is detected, faulty address, written data, and read data
are displayed following the error code 13, and the test is
suspended.
During the test, OSD display becomes blank as the OSD
area is also checked.
(6-3) 1935 SP
ROM t AVD RAM t Video OUT
Error: Not detected.
The data including sub picture streams in ROM are trans-
ferred to the RAM in AVD, and output as video signals
from the AVD.
Though OSD display becomes blank, the output of video
signals continues until the key is pressed.
7. Video Output
(7-2) Color Bar
AVD color bar command write t Video OUT
Error: Not detected.
The command is transferred to the AVD, and the color bar
signals are output from video terminals.
(7-3) Composite Out (European model only)
EURO-AV video output check
AVD color bar command write t Video (EURO-AV) OUT
Error: Not detected.
With the component of video output turned off, the color
bar signals are output from the EURO-AV terminal.
This check is performed for European model only.
(7-4) Y/C Out (European model only)
Y/C video output check
AVD color bar command write t Video (Y/C) OUT
Error: Not detected.
With the Y/C of video output turned on, the color bar sig-
nals are output.
This check is performed for European model only.
(7-5) RGB Out (European model only)
RGB video output check
AVD color bar command write t Video (RGB) OUT
Error: Not detected.
With the RGB of video output turned on, the color bar sig-
nals are output.
This check is performed for European model only.
(7-6) Component Out (European model only)
Component video output check
AVD color bar command write t Video (Component) OUT
Error: Not detected.
With the component of video output turned on, the color
bar signals are output.
This check is performed for European model only.
(7-7) Euro AV Through (European model only)
AV Through output On/Off
Error: Not detected.
AV Through output is turned on.
This check is performed for European model only.
8. Audio Output
(8-2) ARP t1935
Data flow from supply system DRAM to SDRAM of AV
Decoder is tested.
Error 14: ARP t 1935 video NG
15: ARP t 1935 audio NG
(8-3) Test Tone
Pink noise output
Error: Not detected.
In the models without DD output, the test tone is output
from L and R of 2-channel only, and in the models with
DD output, the test tone is output from L and R of 2-chan-
nel, and all channels of 5.1 output.
After turning on all outputs, each time the [NEXT] key is
pressed, the output channel is switched for individual chan-
nel checking.
Diagnosis Check Items List
2. Version Display
(2-2) Revision
(2-3) ROM Check Sum
(2-4) Model Type
(2-5) Region
(2-6) M’t Check
3. Peripheral
(3-2) EEPROM Check
(3-3) Gate Array Check
(3-4) NAND FLASH Check (NAND Flash installed model only)
(3-5) SACD Check (SACD decoder installed model only)
(3-6) Venc Check (Video encoder installed model only)
(3-7) ———— (Function not supported)
(3-8) External RAM Check (External RAM installed model only)
4. Servo
(4-2) Servo DSP Check
(4-3) ———— (Function not supported)
(4-4) RF Amp Register Check
5. Data Supply System
(5-2) ARP Register Check
(5-3) ARP to RAM Data Bus
(5-4) ARP to RAM Address Bus
(5-5) ARP RAM Check
6. AV Decoder
(6-2) 1935 RAM
(6-3) 1935 SP
7. Video Output
(7-2) Color Bar
(7-3) Composite Out (European model only)
(7-4) Y/C Out (European model only)
(7-5) RGB Out (European model only)
(7-6) Component Out (European model only)
(7-7) Euro AV Through (European model only)
8. Audio Output
(8-2) ARP t1935
(8-3) Test Tone
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-5
Error Codes List
00: Error not detected
01: RAM write/read data discord
02: Gate array NG
03: EEPROM NG
04: Flash memory clear error
05: Flash memory write error
06: Flash memory read data discord
07: 2725 read data discord
08: ARP register read data discord
09: ARP Tt RAM data bus error
10: ARP Tt RAM address bus error
11: ARP RAM read data discord
12: Servo DSP NG
13: RF Amp NG
14: 1935 SDRAM NG
15: ARP t1935 video NG
16: ARP t1935 audio NG
19: 1910 UCODE download NG
1A: System call error (Function not supported)
1B: System call error (Parameter error)
1C: System call error (Illegal ID number)
20: System call error (Time out)
21: NAND Flash faulty blocks exceed 10
22: Resistor installation error
50: SACD Decoder W/R NG
52: Video Encoder W/R NG
55: External RAM W/R NG
90: Error occurred
91: User verification NG
92: Diagnosis cancelled
6-4.
DRIVE AUTO ADJUSTMENT
On the Test Mode Menu screen, press [1] key on the remote com-
mander, and the drive auto adjustment menu will be displayed.
Normally, [0] is selected to adjust DVD (single layer), CD, and
DVD (dual layer) in this order. But, individual items can be ad-
justed for the case where adjustment is suspended due to an error.
In this mode, the adjustment can be made easily through the op-
eration following the message displayed on the screen. Which disc
is currently adjusted is displayed on the fluorescent display tube.
0. ALL
You will be asked if EEPROM data are initialized or not, and for
this prompt, select [0] and press the [ENTER] key. First, the servo
setting data in EEPROM, Emergency History and Hour Meter are
cleared to initialize. Then, [1] DVD-SL disc, [2] CD disc, and [3]
DVD-DL disc are adjusted in this order. Each time one disc was
adjusted, it is ejected, and therefore exchange the disc following
the message. You can exit the adjustment by pressing the x but-
ton. In adjusting each disc, the mirror time is measured to check
the disk type. In the auto adjustment, whether the disc type is cor-
rect is not checked unlike conventional models, and accordingly,
take care not to insert a different type of disc.
## Drive Auto Adjustment ##
Adjustment Menu
0. ALL
1. DVD-SL
2. CD
3. DVD-DL
4. LCD
Exit: RETURN
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-6
1. DVD Single Layer Disc
Select [1], insert DVD single layer disc, and press [ENTER] key,
and the adjustment will be made through the following steps, then
adjusted values will be written to the EEPROM. The table No. 1 is
used in the changer type model. If there is no disc on the table No.
1, the tray will be open to wait for closing. If there is a disc on the
table, the adjustment starts immediately. If you put a disc prior to
adjustment, confirm that the SL disc is set on the table 1.
DVD Single Layer Disc Adjustment Steps
1.
SLED Reset
2.
Disc Check Memory SL
3.
Set Disc Type SL
4.
Spdl Start
5.
Ld ON
6.
Focus Error Check
7.
Focus ON 0 with PI Level measure
8.
Auto Track Offset Adjust L0
9.
Trv Level Check
10. Tracking ON
11. CLVA ON
12. Sled ON
13. Auto Focus Balance Adjust
14. Auto Loop Filter Offset Adjust
15. Auto Focus Gain Adjust L0
16. Auto Focus Balance Adjust L0
17. EQ Boost Adjust
18. Auto Loop Filter Offset Adjust
19. Auto Tracking Gain Adjust
20. RF Level Measure
21. Jitter measure
22. Eep Copy Loop Filter Offset
23. All Servo Stop
2. CD Disc
Select [2], insert CD disc, and press [ENTER] key, and the adjust-
ment will be made through the following steps, then adjusted val-
ues will be written to the EEPROM. The table No. 2 is used in the
changer type model. If there is no disc on the table No. 2, the tray
will be open to wait for closing. If there is a disc on the table, the
adjustment starts immediately. If you put a disc prior to adjust-
ment, confirm that the CD is set on the table 2.
CD Adjustment Steps
1.
Sled Reset
2.
Disc Check Memory CD
3.
Set Disc Type CD
4.
Spdl Start
5.
LD ON
6.
Focus Error Check
7.
Fcs ON 1 with PI Level measure
8.
Auto Track Offset Adjust L0
9.
Trv Level Check
10. Tracking ON
11. CLVA ON
12. Sled ON
13. Auto Focus Balance Adjust
14. Auto Loop Filter Offset Adjust
15. Auto Focus Gain Adjust L0
16. Auto Focus Balance Adjust L0
17. Eq Boost Adjust
18. Auto Loop Filter Offset Adjust
19. Auto Track Gain Adjust
20. Copy Adjustment Data to LCD
21. RF Level Measure
22. Jitter measure
23. All Servo Stop
3. DVD Dual Layer Disc
Select [3], insert DVD dual layer disc, and press [ENTER] key, and
the adjustment will be made through the following steps, then ad-
justed values will be written to the EEPROM. The table No. 3 is
used in the changer type model. If there is no disc on the table No.
3, the tray will be open to wait for closing. If there is a disc on the
table, the adjustment starts immediately. If you put a disc prior to
adjustment, confirm that the DL disc is set on the table 3.
DVD Dual Layer Disc Adjustment Steps
1.
Sled Reset
2.
Disc Check Memory DL
3.
Set Disc Type DL
DVD DL Layer 1 Adjust
4.
Spdl Start
5.
LD ON
6.
Fcs ON 1 with PI Level measure
7.
Auto Track Offset Adjust L1
8.
Tracking ON
9.
Clva ON
10. Sled ON
11. Auto Focus Balance Adjust
12. Auto Focus Gain Adjust L1
13. Auto Focus Balance Adjust L1
14. Eq Boost Adjust L1
15. Auto Track Gain Adjust L1
16. Jitter measure
DVD DL Layer 0 Adjust
17. Focus Jump (L1 t L0)
18. Auto Track Offset Adjust L0
19. Tracking ON
20. Clva ON
21. Sled ON
22. Auto Focus Balance Adjust
23. Auto Focus Gain Adjust L0
24. Auto Focus Balance Adjust
25. Eq Boost Adjust L0
26. Auto Track Gain Adjust L0
27. Jitter measure
28. All Servo Stop
4. LCD
LCD disc is not adjusted because the adjusted data of CD are re-
flected, and SACD (hybrid disc) is not adjusted because the ad-
justed data of CD and DVD-DL are reflected.
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-7
6-5.
DRIVE MANUAL OPERATION
On the Test Mode Menu screen, select [2], and the manual opera-
tion menu will be displayed. For the manual operation, each servo
on/off control and adjustment can be executed manually.
In using the Manual Operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is dis-
played when a disc is loaded.
1.
Set correctly the disc type to be used on the Disc Type
setting screen.
The Disc Type setting must be performed after a disc
was loaded.
The set Disc Type is cleared when the tray is opened.
2.
After power ON, if the Manual Operation was selected,
first perform “Reset SLED TILT” by opening 1. Disc Type
screen.
3.
In case of an alarm, immediately press the x button to
stop the servo operation, and turn the power OFF.
Basic operation (controllable from front panel or remote com-
mander)
[POWER] : Power OFF
x : Servo stop
A (Open/Close) : Stop+Eject/Loading
O : Return to Operation Menu or Test Mode Menu
> , . : Transition between sub modes of menu
[1] to [9], [0] : Selection of menu and items
Cursor [Q]/[q] : Increase/Decrease in manually adjusted value
0. Disc Check Memory
On this screen, the mirror time is measured and written to the
EEPROM to check the disc type. First, set a DVD SL disc and
press [1], then set a CD disc and press [2], and finally set a DVD
DL disc and press [3]. The measured mirror time is displayed re-
spectively.
The adjustment must be executed more than once after default
data were written.
From this screen, you can go to another mode by pressing >
or . key, but you cannot enter this mode from another mode.
You can enter this mode from the Operation Menu screen only.
1. Disc Type
On this screen, select the disc type. To select the disc type, press
the number of the loaded disc. The selected disc type is displayed
at the bottom. Selecting [1] automatically selects and displays the
disc type. In case of wrong display, retry “Disc Check Memory”.
Also, opening the tray causes the set disc type to be cleared. In
this case, set the disc type again after loading.
In performing manual operation, the disc type must be set.
## Drive Manual Operation ##
Operation Menu
1. Disc Type
2. Servo Control
3. Track/Layer Jump
4. Manual Adjustment
5. Auto Adjustment
6. Memory Check
0. Disc Check Memory
Exit: RETURN
Disc Check
1. SL Disc Check
2. CD Disc Check
3. DL Disc Check
0. Reset SLED TILT
Disc Type
1. Disc Type Auto Check
2. DVD SL
12cm
3. DVD DL
12cm
4. CD
12cm
5. SACD
12cm
6. DVD SL
8cm
7. DVD DL
8cm
8. CD
8cm
9. LCD
8cm
0. Reset SLED TILT
EMG. 00
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-8
Once the disc type has been selected, the sector address or time
code display field will appear as shown below. These values are
displayed when PLL is locked.
Display when DVD SL 12cm disc was selected
Display when CD 12cm disc was selected
[0] Reset SLED TILT: Reset the Sled and Tilt to initial position.
(Reset the Sled only to initial position be-
cause the Tilt mechanism is not available
in this model.)
[1] Disc Type Check: Judge automatically the loaded disc. As the
judged result is displayed at the bottom of
screen, make sure that it is correct.
If Disc Check Memory menu has not been
executed after EEPROM default setting,
the disc type cannot be judged. In this case,
return to the initial menu and make a check
for three types of discs (SL, DL, CD).
[2] to [9]:
Select the loaded disc. The adjusted value
is written to the address of selected disc.
No further entry is necessary if [1] was se-
lected.
2. Servo Control
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not operate CLVA.
[0] Reset SLED TILT: Reset the Sled and Tilt to initial position.
(Reset the Sled only to initial position be-
cause the Tilt mechanism is not available
in this model.)
[1] LD:
Turn ON/OFF the laser.
[2] SP:
Turn ON/OFF the spindle.
[3] Focus:
Search the focus and turn on the focus.
[4] TRK.:
Turn ON/OFF the tracking servo.
[5] Sled:
Turn ON/OFF the sled servo. When PLL
is not locked (cannot be locked), the sled
servo is not turned ON. The display keeps
ON.)
[6] CLVA:
Turn ON/OFF normal servo of spindle
servo.
[7] FCS. Srch:
Apply same voltage as that of focus search
to the focus drive to check the focus drive
system.
5 Sled FWD:
Move the sled outward. Perform this op-
eration with the tracking servo turned off.
% Sled REV:
Move the sled inward. Perform this opera-
tion with the tracking servo turned off.
Disc Type
1. Disc Type Auto Check
2. DVD SL
12cm
3. DVD DL
12cm
4. CD
12cm
5. SACD
12cm
6. DVD SL
8cm
7. DVD DL
8cm
8. CD
8cm
9. LCD
8cm
0. Reset SLED TILT
TC. :: EMG.00
CD
12cm
Disc Type
1. Disc Type Auto Check
2. DVD SL
12cm
3. DVD DL
12cm
4. CD
12cm
5. SACD
12cm
6. DVD SL
8cm
7. DVD DL
8cm
8. CD
8cm
9. LCD
8cm
0. Reset SLED TILT
SA. SI. EMG.00
DVD SL 12cm
Servo Control
1. LD
Off R. Sled FWD
2. SP
Off L. Sled REV
3. Focus
Off
4. TRK.
Off
5. Sled
Off
6. CLVA
Off
7. FCS. Srch
Off
0. Reset SLED TILT
SA. SI. EMG.00
DVD SL 12cm
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-9
3. Track/Layer Jump
On this screen, track jump, etc. can be performed. Only for the
DVD-DL, the focus jump and layer jump are displayed in the right
field.
[1] 1Tj FWD:
1-track jump forward.
[2] 1Tj REV:
1-track jump reverse.
[3] 2Tj FWD:
2-track jump forward.
[4] 2Tj REV:
2-track jump reverse.
[5] NTj FWD:
N-track jump forward.
[6] NTj REV:
N-track jump reverse.
[7] 500Tj FWD:
Fine search forward.
[8] 500Tj REV:
Fine search reverse.
[9] 10k/20k FWD: Direct search forward.
[0] 10k/20k REV: Direct search reverse.
– The following commands are valid for DVD-DL disc only –
5 (L1 t L0): Focus jump (Trk/Sled Servo OFF) forward.
% (L0 t L1): Focus jump (Trk/Sled Servo OFF) reverse.
$ (L1 t L0): Layer jump (Trk/Sled Servo ON) forward.
4 (L0 t L1): Layer jump (Trk/Sled Servo ON) reverse.
4. Manual Adjustment
On this screen, each item can be adjusted manually. Select the
desired number [1] to [0] from the remote commander, and cur-
rent setting for the selected item will be displayed, then increase
or decrease numeric value with $ key or 4 key. This value is
stored in the EEPROM. If CLV has been applied, the jitter is dis-
played for reference for the adjustment.
[1] TRK. Offset:
Adjusts tracking offset.
[2] Focus Gain:
Adjusts focus gain.
[3] TRK. Gain:
Adjusts track gain.
[4] Focus Offset:
Adjusts focus offset.
[5] Focus Balance: Adjusts focus balance.
[6] L.F. Offset:
Adjusts loop filter offset.
[7] Analog FRSW: Sets select switch of analog feedback circuit.
[8] PLL Dac Gain: Adjusts D/A converter gain of PLL.
[9] EQ BOOST:
Adjusts boost amount of equalizer.
[0] GD ADJ:
Adjusts group delay amount.
Track/Layer Jump
1. 1Tj FWD
R. Fj (L1->L0)
2. 1Tj REV
L. Fj (L0->L1)
3. 2Tj FWD
U. Lj (L1->L0)
4. 2Tj REV
D. Lj (L0->L1)
5. NTj FWD
6. NTj REV
7. 500Tj FWD
8. 500Tj REV
9. 10k/20k FWD
0. 10k/20k REV
SA. SI. EMG.00
DVD DL 12cm
Manual Adjustment:Up/Down
1. TRK. Offset
2. Focus Gain
3. TRK. Gain
4. Focus Offset
5. Focus Balance
6. L.F. Offset
7. Analog FRSW
8. PLL Dac Gain
9. EQ BOOST
0. GD ADJ
Adjustment: Up/Down
SA. ------ SI. -- EMG. 00
DVD SL 12cm Jitter FF
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-10
5. Auto Adjustment
On this screen, each item can be adjusted automatically. Select the
desired number [1] to [8] from the remote commander, and se-
lected item is adjusted automatically.
[1] Auto TRK. Offset:
Adjusts tracking offset.
[2] Auto Focus Balance: Adjusts focus balance.
[3] Auto Focus Offset:
Adjusts focus offset.
[4] Auto Focus Gain:
Adjusts focus gain.
[5] Auto TRK. Gain:
Adjusts track gain.
[6] Auto EQ
[7] Auto L.F. Offset:
Adjusts loop filter offset.
[8] Auto Group Delay
6. Memory Check
The display image is shown below and three screens in total can
be selected.
On this screen, current servo adjusted data stored in the EEPROM
are displayed. The adjusted data are initialized by pressing the
[CLEAR] key, but be careful that they are not recoverable after
initialization.
Before clearing the adjusted data, make a note of the set data. This
screen will also appear if [0] All is selected in the Drive Auto
Adjustment. In this case, default setting cannot be made.
“THR A&L” data on the second page cannot be changed if default
setting is once made.
Auto Adjustment
1. Auto TRK. Offset
2. Auto Focus Balance
3. Auto Focus Offset
4. Auto Focus Gain
5. Auto TRK. Gain
6. Auto EQ.
7. Auto L.F. Offset
8. Auto Group Delay
SA.04EF905 SI.00 EMG.00
DVD SL 12cm
EEPROM DATA 1
DL
CD
LCD SL
L0
L1
Focus Gain
xx
xx
xx xx
xx
TRK. Gain
xx
xx
xx
xx
xx
FCS Balnce
xx
xx
xx
xx
xx
Focus Bias
xx
xx
xx
xx
xx
TRV Offset
xx
xx
xx
xx
xx
L.F. Offset
xx
xx
xx
xx
xx
EQ. Boost
xx
xx
xx
xx
xx
_
UP
: Last Data
DOWN
: Next Data
CLEAR : Default Set
page.1/3
EEPROM DATA 2
DL
CD
LCD SL
L0
L1
RF Jitter
xx
--
xx
xx
xx
RF Level
xx
--
xx
--
--
FE Level
xx
--
xx
--
--
FE Balance
xx
--
xx
--
--
TRV.Level
xx
--
xx
--
--
TE Gain
xx
xx
--
--
--
PI Level
xx
--
xx
xx
--
_
UP
: PREV Data
DOWN
: Next Data
CLEAR : Default Set
page.2/3
EEPROM DATA 3
DL
CD
LCD SL
L0
L1
Analog FRSW
xx
xx
xx
xx
xx
PLL Dac Gain
xx
xx
xx
xx
xx
Mirror Time
xx
xx
xx
xx
xx
_ THR A&L
xx
xx
xx/xx xx
xx
UP
: PREV Data
DOWN
: First Data
CLEAR : Default Set
page.3/3
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-11
6-6.
MECHA AGING
On the Test Mode Menu screen, selecting [3] executes the aging
of mechanism. First, open the tray and load a disc. Press the H
key, and the aging will start. When the tray is closed, the disc type
and size are judged and displayed. During aging, the number of
the repeat cycle is displayed. Aging can be aborted at any time by
pressing the x key. After the operation has stopped, unload the
disc and press again the x key or the O key to return to the Test
Mode Menu.
6-7.
EMERGENCY HISTORY
On the Test Mode Menu screen, selecting [4] displays the infor-
mation such as servo emergency history. The history information
from last “1” up to “10” can be scrolled with $ key or 4 key.
Also, specific information can be displayed by directly entering
that number with the ten-key pad from [1] to [9].
(Emergency history code is shown separately.)
The upper two lines display the laser ON total hours. Data below
minutes are omitted.
Clearing History Information
Clearing laser hours
Press [DISPLAY] and [CLEAR] keys in this order.
Both CD and DVD data are cleared.
Clearing emergency history
Press [TITLE] and [CLEAR] keys in this order.
Initializing setup data
Press [DVD menu] and [CLEAR] keys in this order.
The data have been initialized when “Set Up Initialized” mes-
sage is displayed.
The EMG. History display screen will be restored soon.
6-8.
VERSION INFORMATION
The ROM version, region code, OPT type, etc. are displayed if [5]
is selected in the Test Mode Menu. The parenthesized hexadeci-
mal number in the version number field indicates the checksum
value of the ROM.
* Note after Downloading
After downloading ROM data, sometimes it happens that checksum
is not the same as that of ROM data that has been downloaded.
In such a case, go back to the menu screen and select “0. Syscon
Diagnosis”, then select “1. All” in “2. Version”. If the result of this
operation does not give an agreement, it must be either Download
error or ROM error.
6-9.
VIDEO LEVEL ADJUSTMENT
On the Test Mode Menu screen, selecting [6] displays color bars
for video level adjustment. During display of color bars, OSD dis-
appears but the menu screen will be restored if pressing any key.
### Mecha Aging ###
Press OPEN key
Abort : STOP key
### EMG. History ###
Laser Hours
CD
xxhxxm
DVD
xxhxxm
1.
00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
2.
00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00
Select : 1-9
Scroll :UP/DOWN
(1: Last EMG.)
Exit
:RETURN
### Version Infomation ###
IF con.
Ver.x.xxx(xxxx)
Group
xx
SYScon.
Ver.x.xxx(xxxx)
Model
xx
Region
0x
Servo DSP Ver:x.xxx
AVD ucode Ver:xxxxxxxx
OPT TYPE : x LASER
Exit : RETURN
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-12
6-10. IF CON SELF DIAGNOSTIC FUNCTION
1. IF-89 BOARD (IF CON) TEST MODE
The IF-89 board (IF CON) test mode is the IF CON self-diagnosis
mode. The IF CON can diagnose the functions of the IF-89 board
that the IF CON controls. Normally, the IF CON makes a serial
communication with the SYSTEM CONTROL and operates fol-
lowing the commands from the SYSTEM CONTROL, but in the
Test mode, the IF CON operates independently from the SYS-
TEM CONTROL.
In the test mode, the following functions can be checked.
1.
Button function
2.
Remote commander receiving function
3.
SYSTEM CONTROL-IF CON serial communication
4.
Click shuttle function
5.
Fluorescent display tube lighting check
Grid check
Anode check
6.
LED control function
In the test mode, the main unit operates same as usual, except
voltage monitoring, communication monitoring, display of fluo-
rescent display tube, and LED control.
1.
The routine that monitors +3.3 V (PCONT) of MB-103 board
is not provided.
2.
The monitoring timer for serial communication with the SYS-
TEM CONTROL is not provided. The main unit is not placed
in the Standby mode, even if the communication with SYS-
TEM CONTROL is normal.
3.
Display of fluorescent display tube.
(Normally, display is made following the commands from SYS-
TEM CONTROL)
4.
LED control.
(Normally, control is made following the commands from SYS-
TEM CONTROL)
2. OPERATION OF SELF CHECK MODE
The Self Check mode is the function to conduct the basic test to
the FL display and DVD panel section.
2-1. Self Check Mode Transition Processing
At the AC Power ON after reset of IF CON is released with the
MB-103 board are not connected to the AV-61 board, or while
pressing the x key on the main unit with the IF CON in
STANDBY mode, enter [RETURN] t [DISPLAY] (or [SET UP])
on the remote commander, and the main unit transits to the Self
Check Mode.
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-13
2-2. Operation of Auto Self Check
When the Self Check mode becomes active at the AC Power ON or by key input, the test display of the following steps (1) to (4) is
repeated.
(1) FLD and LED all ON (for 5 seconds)
(2) MODEL display (for 2 seconds)
(3) Version display (for 2 seconds)
(4) ROM creation date display (for 2 seconds)
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-14
2-3. Each Self Check Function
Each Self Check function tests the FLD display, LED display, and
key input.
2-3-1. FLD and LED All ON
2-3-1-1. Transition Keys in Self Check Mode
• x key and Z key on the main unit
• % key on the main unit and the remote commander
2-3-1-2. Operation and Display
In this mode, all LEDs except STANDBY LED and all segments of
FLD turn ON.
• Example of FLD all ON
2-3-2. Main Unit Key Name Display and Key Code Display
2-3-2-1. Transition Keys in Self Check Mode
• Keys on the main unit except keys transited in Self Check Mode
2-3-2-2. Operation and Display
When a key on the main unit is pressed in the Self Check mode, the
name of that key is displayed on the FLD. Also, the key name display
and the key code display can be switched with the [DISPLAY] key on
the remote commander. “NOTHING” is displayed when nothing is
entered. Also, VIDEO CD, DVD, and CD segments turn on when a
communication error occurred.
• FLD display (at input of H key on the main unit)
Input
IC404: Pin No. (Signal)
Voltage [V]
Pin ed (BNRKEY)
Pin ef (PLAY)
Pin eg (O/C)
Pin eh (TVS)
0 – 0.2
–
PLAY
OPEN/CLOSE
TVS
0.6 – 0.82
–
NEXT
–
PIC MODE
1.16 – 1.47
–
PREVIOUS
–
MODE
1.8 – 2.12
–
PAUSE
–
–
2.48 – 2.7
–
STOP
–
–
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-15
• Key code display
(at input of H key, key code: 0 Ah)
• At input of faulty voltage
• Remote commander key code display
(at input of X key, key code: 39 h)
• When key is pressed double
2-3-3. Remote Commander Key Name Display and Key
Code Display
2-3-3-1. Transition Keys in Self Check Mode
• Remote commander keys except keys transited in Self Check Mode
2-3-3-2. Operation and Display
When a key on the remote commander is pressed in the Self Check
Mode, the name of that key is displayed on the FLD. Also, the key
name display and the key code display can be switched with the
[DISPLAY] key on the remote commander. “NOTHING” is displayed
when nothing is entered. Also, VIDEO CD, DVD, and CD segments
turn on when a communication error occurred.
• Remote commander key name display (at input of X key)
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-16
2-3-4. Communication Monitoring Display
The communication state is monitored and displayed while the
key name on the main unit and the remote commander is displayed.
When the communication to the System Controller failed, VIDEO
CD, DVD, and CD segments turn on.
2-3-5. FLD Anode Test Display and SHUTTLE Click
Operation Test
2-3-5-1. Transition Keys in Self Check Mode
• 5 key on the remote commander
• SHUTTLE on the remote commander during Anode Test display
(This unit does not provide JOG/SHUTTLE, and therefore use
another DVD remote commander having the JOG/SHUTTLE)
2-3-5-2. Operation and Display
The Self Check Mode transits to this mode when 5 key is en-
tered. This tests whether each segment turns on individually. Only
the first segment of each grid of FLD turns on, and each time the
SHUTTLE is entered, the segment of each grid is switched in or-
der. When SHUTTLE input is clockwise, the segment switches in
1 – 2 – 3 direction, or counterclockwise it switches in 3 – 2 – 1
direction.
• Display at the start of Anode Test
• Communication error display
(at no input of key and remote commander)
• Communication error display
(at code display without input of the remote commander)
r (Input in CW direction)
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-17
2-3-6. FLD Grid Test Display and SHUTTLE Click Opera-
tion Test
2-3-6-1. Transition Keys in Self Check Mode
• $ key on the remote commander
• SHUTTLE on the remote commander during Grid Test display
(This unit does not provide JOG/SHUTTLE, and therefore use an-
other DVD remote commander having the JOG/SHUTTLE)
2-3-6-2. Operation and Display
The Self Check Mode transits to this mode when $ key is entered.
This tests whether each grid turns on individually. The first grid only
of FLD turns on and other grids turn off. Each time the SHUTTLE is
entered, the grid is switched in order. When SHUTTLE input is clock-
wise, the grid switches in 1 – 2 – 3 direction, or counterclockwise it
switches in 3 – 2 – 1 direction.
• Display at the start of Grid Test
r (Input in CW direction)
2-3-7. LED Test Display
2-3-7-1. Transition Keys in Self Check Mode
• 4 key on the remote commander
• SHUTTLE on the remote commander during Grid Test display
(This model does not provide JOG/SHUTTLE, and therefore use
another DVD remote commander having the JOG/SHUTTLE)
2-3-7-2. Operation and Display
LED is switched in order by the input of JOG/SHUTTLE on the re-
mote commander. Also, LED ON/OFF is switched by the input of
same key as the function that turns on the LED concerned.
• FLD display during LED Test
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-18
a
f
h
g
e
r
p
n
s
c
col
m
d
Dp
j
k
b
7G
6G
5G
4G
3G
2G
1G
P1
col
col
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
a
h
j
k
b
f
m
s
g
e
n
p
r
c
d
Dp
a
h
j
k
b
f
m
s
g
e
n
p
r
c
d
Dp
a
h
j
k
b
f
m
s
g
e
n
p
r
c
d
Dp
a
h
j
k
b
f
m
s
g
e
n
p
r
c
d
Dp
a
h
j
k
b
f
m
s
g
e
n
p
r
c
d
Dp
a
h
j
k
b
f
m
s
g
e
n
p
r
c
d
Dp
a
h
j
k
b
f
m
s
g
e
n
p
r
c
d
ANODE CONNECTION
( 7G-1G)
1G
7G
6G
5G
4G
3G
2G
1G
2G
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
6-19
6-11. TROUBLESHOOTING
6-11-1. Cannot Enter Test Mode
You cannot enter the Test mode when either button has been pressed
by any reason with the board assembled in the front panel. In this
state, the power does not turn on even under normal condition (the
unit is kept in standby state), and also no button is active and the
remote commander is not accepted. In this case, disconnect the
MB-103 board and AV-61 board, and with the SELF CHECK (pin
0) of IF CON (IC404) on the IF-89 board kept in low state, sup-
ply AC, and the IF CON self-diagnosis mode will be forcibly acti-
vated. The IF CON (IC404) checks the SELF CHECK port only
after the power on reset (only at AC supply, not in standby state).
If any button is pressed, its name is displayed on the fluorescent
display tube. But, if other than “NOTHING” is displayed though
no button is pressed, it means that any button has been pressed.
6-11-2. Faults in Test Mode (MB-103 board)
1. The test mode menu is not displayed.
1-1. Board visual check
Check that the ICs of SYSCON (IC104), ROM (IC106 or
IC107), AVD (IC403), ARP & SERVO (IC301) are working
correctly.
Check that outside appearance of the ICs is normal.
Check that IC pins are not short-circuited.
Check that there is no soldering error.
Check that outside appearance of the capacitors and resistors
is normal.
1-2. Power supply voltage check
Check the power voltage of the power connector (CN102).
Check the power voltage of SYSCON (IC104).
Check the power voltage of ROM (IC106 or IC107).
Check the power voltage of AVD (IC403).
Check the power voltage of ARP & SERVO (IC301).
If the power voltage has any abnormality t
Check that the power supply lines are not shorted.
Check that there is no soldering error.
If any abnormality cannot be found still t
Check that each IC is working normally.
1-3. Clock signal check
Measure the clock signal frequency at CPUCK (CL101) of
SYSCON (IC104) with an oscilloscope.
If the 8.25 MHz signal appears. t Check the machine ac-
cording to section 1-3-1
If the 33 MHz signal appears. t Check the machine accord-
ing to section 1-3-2.
If other frequencies are output.
R110 and R113 have defective soldering, X101 crystal os-
cillator is defective.
If the measurement point is fixed to either “H” or “L”. t
Observe XFRRST (pin-uh) of SYSCON (IC104) with an
oscilloscope.
If the measurement point is “L”, check the following items.
If the IC has defective soldering, if the IC is short-circuited.
If the measurement point is “H”,
t Component X101 or SYSCON (IC104) is defective.
1-3-1. When the 8.25 MHz signal appears at CPUCK
• Check the XRD, XWRH and CS0X signal.
Observe XRD (pin-u;), XWRH (pin-ua), and CS0X (pin-tk)
of SYSCON (IC104) with an oscilloscope.
If these pins are fixed to either “L” (0V) or “H” (3.3V), or if
these pins stay in the center voltage, check the followings.
Check if the signal line does not have the defective solder-
ing.
Check if the signal line is short-circuited with other signal
lines.
If you cannot find any problem t SYSCON (IC104) is
defective.
• HA [0 to 21] signal and HD [0 to 15] signal check
Observe HA [0 to 21] (pins-
