ORDER NO. PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2005 GEX-P10XMT/XN/UC CRT3424 XM DIGITAL SATELLITE DATA & AUDIO RECEIVER GEX-P10XMT/XN/UC For details, refer to "Important Check Points for Good Servicing". K-ZZW. FEB. 2005 Printed in Japan - Caution • When users complain "No Signal" is displayed, there is a possibility that an installed XM antenna cable has shorted out only occasionally. If there are no problems in the main tuner by a service-man checking or NTF is used, let users confirm that the XM antenna cable has no short-circuit. • Connect the Acc lead of the Cord Assy (CDE8009) only when IP-BUS is not connected. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 2 1 2 3 4 1 2 3 4 C D F A B E SAFETY INFORMATION CAUTION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair performed can adversely affect the and reliability of the product and may void the . If you are not qualified to the repair of this product properly and , you should not risk trying to do so WARNING WARNING W This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of Health & Safety Code Section 25249.6 - Proposition 65 - Service Precautions 1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 3 5 6 7 8 5 6 7 8 C D F A B E [Important Check Points for Good Servicing] In this manual, procedures that must be performed during repairs are marked with the below symbol. Please be sure to confirm and follow these procedures. 1. Product safety Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual. 1 Use specified parts for repair. Use genuine parts. Be sure to use important parts for safety. 2 Do not perform modifications without proper instructions. Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise. 3 Make sure the soldering of repaired locations is properly performed. When you solder while repairing, please be sure that there are no cold solder and other debris. Soldering should be finished with the proper quantity. (Refer to the example) 4 Make sure the screws are tightly fastened. Please be sure that all screws are fastened, and that there are no loose screws. 5 Make sure each connectors are correctly inserted. Please be sure that all connectors are inserted, and that there are no imperfect insertion. 6 Make sure the wiring cables are set to their original state. Please replace the wiring and cables to the original state after repairs. In addition, be sure that there are no pinched wires, etc. 7 Make sure screws and soldering scraps do not remain inside the product. Please check that neither solder debris nor screws remain inside the product. 8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord. Damaged power cords may lead to fire accidents, so please be sure that there are no damages. If you find a damaged power cord, please exchange it with a suitable one. 9 There should be no spark traces or similar marks on the power plug. When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary. 0 Safe environment should be secured during servicing. When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely. 2. Adjustments To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification. Adjustments should be performed in accordance with the procedures/instructions described in this manual. 4. Cleaning For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances. 3. Lubricants, Glues, and Replacement parts Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied. 5. Shipping mode and Shipping screws To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 4 1 2 3 4 1 2 3 4 C D F A B E CONTENTS SAFETY INFORMATION..................................................................................................................................... 2 1. SPECIFICATIONS ............................................................................................................................................ 5 2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6 2.1 PACKING ................................................................................................................................................... 6 2.2 EXTERIOR................................................................................................................................................. 8 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM.......................................................................................... 10 3.1 BLOCK DIAGRAM ................................................................................................................................... 10 3.2 MAIN UNIT(DSP)..................................................................................................................................... 12 3.3 MAIN UNIT(SYSCOM)............................................................................................................................. 18 3.4 TUNER UNIT ........................................................................................................................................... 24 4. PCB CONNECTION DIAGRAM ..................................................................................................................... 26 4.1 MAIN UNIT............................................................................................................................................... 26 4.2 TUNER UNIT ........................................................................................................................................... 30 5. ELECTRICAL PARTS LIST ............................................................................................................................ 32 6. ADJUSTMENT ............................................................................................................................................... 39 6.1 TEST MODE ............................................................................................................................................ 39 7. GENERAL INFORMATION............................................................................................................................. 51 7.1 DIAGNOSIS ............................................................................................................................................. 51 7.1.1 DISASSEMBLY ..................................................................................................................................... 51 7.1.2 CONNECTOR FUNCTION DESCRIPTION.......................................................................................... 52 7.2 IC ............................................................................................................................................................. 53 7.3 OPERATIONAL FLOW CHART ............................................................................................................... 60 8. OPERATIONS ................................................................................................................................................ 61 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 5 5 6 7 8 5 6 7 8 C D F A B E 1. SPECIFICATIONS General Power source ...................... 14.4 V DC (10.8 – 15.1 V allowable) Grounding system .............. Negative type Max. current consumption ............................................. 2.0 A Backup current..................... 3.0 mA or less Dimensions (W x H x D) ..... 179 x 27 x 139 mm (7 x 1 x 5-1/2 in.) Weight ................................. 0.57 kg (1.26 lbs) XM tuner Frequency range ................. 2,332.50 – 2,345.00 MHz Usable sensitivity Satellite ....................... – 105.0 dBm Terrestrial .................... – 102.0 dBm Audio Signal-to-noise ratio ........... 90 dB (IHF-A network) Separation .......................... 85 dB Antenna Power source (Provided by the satellite line) ............................................. 4.9 V DC (4.4 – 5.4 V allowable) Max. current consumption ............................................. 0.1 A Type ..................................... Active type Dimensions Base (W x H x D) ........ 29 x 14 x 40 mm [1-1/8 x 1/2 x 1-5/8 in] Cord ............................ 5 m Weight ................................. 0.06 kg (0.13 lbs) Due to possible improvements, specifications and design are subject to change without notice. Note www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 6 1 2 3 4 1 2 3 4 C D F A B E 2. EXPLODED VIEWS AND PARTS LIST 2.1 PACKING NOTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. • The > mark found on some component parts indicatesthe importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. • Screw adjacent to mark on the product are used for disassembly. • For the applying amount of lobricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) " 1 4 22 14 13 16 16 15 10 11 15 12 3 2 5 6 6 7 8 8 9 17 19 18 20 21 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 7 5 6 7 8 5 6 7 8 C D F A B E PACKING SECTION PARTS LIST Mark No. Description Part No. * 1 Card ARY1048 2 Cord Assy CDE5880 3 Cord Assy CDE8009 4 Cord Assy CDE7836 5 Screw Assy CEA5014 6 Screw BNC40P120FTB * 7 Polyethylene Bag CEG1158 8 Screw HMF40P060FTB 9 Cover CEG1098 * 10 Polyethylene Bag CEG1101 11 Polyethylene Bag CEG1116 12 Sub Carton CHG5471 13 Carton CHG5472 14 Contain Box CHL5472 15 Protector CHP2968 16 Protector CHP2969 17 Angle CNB2351 18 Owner's Manual(English) CRB2045 19 Installation Manual(English) CRB2046 * 20 Registration Card CRY1229 * 21 Caution Card CRN1079 22 Antenna Assy CXC4683 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 8 1 2 3 4 1 2 3 4 C D F A B E 2.2 EXTERIOR 8 7 9 3 5 4 1 1 1 1 1 1 1 11 19 26 26 26 15 13 20 21 23 24 14 12 16 17 18 A B www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 9 5 6 7 8 5 6 7 8 C D F A B E EXTERIOR SECTION PARTS LIST Mark No. Description Part No. 1 Screw BMZ26P030FTC 2 ••••• 3 Cord Assy CDE8009 > 4 Fuse(2A) CEK1018 5 Cap CNS6329 6 ••••• 7 Chassis CNA2807 8 Case CNB3106 9 Insulator CNM9419 10 ••••• 11 Main Unit CWM9857 12 Terminal(CN603) CKF1064 13 Plug(CN901) CKS-460 14 Connector(CN402) CKS3409 15 Connector(CN401) CKS3410 16 Connector(CN451) CKS4473 17 Holder CND2697 18 Shield CND2744 19 Tuner Unit CWE1933 20 Connector(CN502) CKS5145 21 Connector(CN501) CKX1085 22 ••••• 23 Shield CND2639 24 Holder CND2640 25 ••••• 26 Screw ISS26P055FTC www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 10 1 2 3 4 1 2 3 4 C D F A B E 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1 BLOCK DIAGRAM 8 CN502 IF_Q+ IF_Q- IF_I- IF_I+ IF_AGC SYS_CLK CN301 6 12 10 35 2 18 26 VDD_M3.3V 25 VCC_RF3.3V 6 5 17 97 4 IC502 MAX999EUK AMP IC501 MAX2140ETH ZIF TUNER F501 CN501 XM SINGLE ANTENNA IC370 ST19AF08BR20QMAA QOUT- RFIN+ RFIN- IFOUT+ IFOUT- IFIN- IFIN+ IF2IO+ IF2IO- IF2II+ IF2II- IF2QO+ IF2QO- XTAL IF2QI+ IF2QI- VOUTANT QOUT+ IOUT- IOUT+ SDA SCL CAP CAP_SDA_M 96 CAP_SCL_M 93 I2C_DATA I2C_CLOCK RST CAP_RST MCLK 1 84 83 82 81 2 1 7 8 3 16 4 CLKO SD0 SCKT LRCKT OCLK MCLK INP1 INM1 INM2 INP2 AGC1 34 21 22 5 1 8 2 3 44 43 REFOUT 25 AGCPWM 9 16 8 6 12 10 2 18 26 VCC_ANT5.0V DIG_3.3V SDA SCL SDA SCL SDA SCL RF_3.3V ANT_5.0V 25 17 17 15 15 1 1 IN- 4 1 OUT IN OUT2 OUT1 F502 1 5 6 10 11 10 5 6 20 18 19 17 36 38 37 39 IN1 IN2OUT2 OUT1 IC360 K4S280832F-TC75 IC300 STA850P BS0,BS1 RAS,CAS,DQM CSO,WE,CLK,CKE LSDPRX A0-A11 D0-D7 LCH RCH DAC_EN DAC_CL DAC_DT DAC_EN DAC_CL TEST POINT MASTER 15 Slave/master 14 MFP_CLK 18 17 37 64 65 69 66 108 107 106 100 99 98 34 33 108 107 106 100 99 98 34 33 PCBS_SYNC 4 PCDC0 PCFS0 MRESET RESET_N PCSD0 MFP_CLK SM PCBS_SYNC PCDC0 PCFS0 CRESET SRESET PCSD0 MFP_CLK SM PCBS_SYNC PCDC0 PCFS0 CRESET SRESET PCSD0 MCLK IC260 K4S280832F-TC75 X602 11 95 93 13 IC200 STA850P SBS0,SBS1 SRAS,SCAS,SDQM SCSO,SWE, SCLK,SCKE SA0-SA11 SD0-SD7 MRESET RESET_N SLAVE SDRAM SDRAM SDA SCL SDA SCL 15 14 13 57 100 IC480 PCM1742KE D/A CONVERTER LPF DATA VoutL BCKIN VoutR LRCKIN MCLK ML MC MD 2 6 1 7 OUT1 OUT2 IN-1 IN-2 IC490 NJM4558MD INTR CDEC_INTR RS232TX IC603 S-80827CNNB-B8M RESET VDD 2 1 10 59 65 18 OUT RESET_N INTR MRESET 10 TX RX 3 18 30 S602 RESET SW X601 11 13 SDA SCL X501 24 INP1 INM1 INM2 INP2 15 14 18 17 64 65 DAC_DT 99 A0-11 DQ0-7 MADD0-11 MDQ0-7 A0-11 BA0,1 RAS_,CAS_, DQM,CS_, WE_,CLK,CKE DQ0-7 MADD0-11 RAS,CAS,MDQM,MCSO MBS0,1 MWE,CLKON,MCKE BA0,1 RAS_,CAS_, DQM,CS_, WE_,CLK,CKE RAS,CAS,MDQM, MBS0,1 NCSO,MWE,CLKON,MCKE MDQ0-7 VDD_3.3V MAIN UNIT A TUNER UNIT B www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 11 5 6 7 8 5 6 7 8 C D F A B E 3 10 LCH RCH _EN _CL _DT DAC_EN DAC_EN DAC_CL DACCL TEST POINT MUTE MUTE IC605 PEG100A SUB SYSTEM CONTROL IC601 PEG099A MAIN SYSTEM CONTROL X602 Xout Xin 11 95 49 37 73 71 93 13 57 34 33 36 33 34 17 100 42 LPF GND ISORATOR 1 7 OUT1 OUT2 -1 -2 19 18 LCH RCH 14 7 9 2 RCH RCH 12 10 8 LCH OUT1 OUT1 OUT2 OUT2 IN2A IN2B IN1B IN1A -IN2A -IN1A +IN1B +IN2B LCH 15 13 1 IC490 NJM4558MD IC403 TA2050FS1 AUDIO SELECTOR IC401 BA3131FS IP-BUS DRIVER 6 7 5 BUS+ BUS- DIN1 DOUT STBY 1 2 8 IC451 HA12240FP SEL ANSW 43 CN401 11 7 9 10 5 8 1 8 10 RS232C DRIVER 11 13 Rin2 Dout2 Rout2 VDD Din2 IC452 UPD4721GS CN402 11 7 9 10 5 8 1 Q402 ASENB MUTE MUTE DRIVE INV. SWITCH Q454 Q453 Q405 Q404 Q403 Q452 CN451 7 3 10 8 3 2 1 B-B8M T 1 10 59 65 18 UT /RESET RESET_N RESET_N INTR INTR MRESET MRESET 10 TX RX 1 2 3 18 30 /RESET DATAINT MAINTX MAINRX NC9 /SUBRES SUBTX SUBRX LSDPRX NAVIRX NAVITX 2 SW X601 Xout Xin 11 27 28 13 BUP Q801 Q911 VDD5V REGULATOR BACKUP SENSE ACC SENSE CN901 Q802 BUP ACC 1,5 4 NJM2880U1-05 IC802 1,5 4 S-T111B33MC-OGS IC801 DAC5V REGULATOR 9 AN8011S IC851 3.3V/6V DUAL DC/DC CONVERTER VDD3.3V REGULATOR AUDIO8V REGULATOR Q811 Q812 SYSPW SYSPW SDA SCL SDA SCL Q854 Q852 OUT2 OUT1 ON/OFF VCC FU855 1,2,4 3 PQ012FZ01ZP IC830 1.2V REGULATOR DIG_3.3V VDD_3.3V BUP DIG_1.2V RF_3.3V ANT_5.0V VDD_3.3V 1 1,5 3 4 BA033CC0FP IC842 NJM2880U1-05 IC841 5V REGULATOR 6V REGULATOR 3.3V REGULATOR 3.3V REGULATOR 5V DAC_5V AUDIO_8V ACCPW2 ACCPW2 BSENS ASENS BSENS /BSENS ASENS /ASENS 7 Q853 Q851 FU854 82 XMPW IPIN IPOUT(TX) 28 IPPW IPIN(RX1) 27 ASENB /ASENB 72 IPOUT IPPW 20 IPSW IPSW 40 ACCPW2 DAC_DT DACDT 99 MUTE IPIN IPOUT IPPW ACCPW2 ACCPW2 IPSW 3 FU851 FU451 FU452 SEL SW2 SWITCH Q451 VCC 5V 1 BACKUP ACC GND DATA OUT IP-BUS OUT IP-BUS IN www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 12 1 2 3 4 1 2 3 4 C D F A B E 3.2 MAIN UNIT(DSP) 1/2 A A-a 1/2 A-a A-b A-a A-b A-b A-a Large size SCH diagram Guide page Detailed page Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". B CN502 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 13 5 6 7 8 5 6 7 8 C D F A B E 1/2 A A-b 1/2 MAIN UNIT(DSP) 1/2 A 2/2 A Decimal points for resistor and capacitor fixed values are expressed as : 2.2 2R2 0.022 R022 ← ← The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. NOTE : Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. DAC LPF www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 14 1 2 3 4 1 2 3 4 C D F A B E A-a A-b A-a A-b 1/2 A-a 1/2 1 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 15 5 6 7 8 5 6 7 8 C D F A B E A-a A-b A-a A-b 1/2 A-a 1/2 2 B CN502 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 16 1 2 3 4 1 2 3 4 C D F A B E A-a A-b A-b 1/2 1 MAIN UNIT(DSP) 1/2 A 2/2 A Decimal points for resistor and capacitor fixed values are expressed as : 2.2 2R2 0.022 R022 ← ← The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. NOTE : Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. DAC www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 17 5 6 7 8 5 6 7 8 C D F A B E A-a A-b A-b 1/2 2 LPF www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 18 1 2 3 4 1 2 3 4 C D F A B E 3.3 MAIN UNIT(SYSCOM) 2/2 A A-a 2/2 > > 1/2 A SYSTEM MICROCOMPUTER DATA MICROCOMPUTER 3.3V/6V D DC/DC C DIGITAL 1.2V REGULATOR RF 3.3V REGULATOR ANT 5V REGULATOR : The power supply is shown with the marked box. R www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 19 5 6 7 8 5 6 7 8 C D F A B E 2/2 A A-b 2/2 > > > ROCOMPUTER AUDIO SELECTOR IP-BUS DRIVER DATA COMMUNICATION VDD 3.3V REGULATOR 5V REGULATOR ACC SENSE BACKUP SENSE AUDIO 8V REGULATOR DAC 5V REGULATOR 3.3V/6V DUAL DC/DC CONVERTER DATA OUT IP-BUS OUT IP-BUS IN BACKUP > 2A GND ACC MAIN UNIT(SYSCOM) 2/2 A RESET www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 20 1 2 3 4 1 2 3 4 C D F A B E A-a A-b A-a A-b 2/2 A-a 2/2 2 4 3 1 > > 1/2 A 3.3V/6 DC/D DIGITAL 1.2V REGULATOR RF 3.3V REGULATOR ANT 5V REGULATOR www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 21 5 6 7 8 5 6 7 8 C D F A B E A-a A-b A-a A-b 2/2 A-a 2/2 5 SYSTEM MICROCOMPUTER DATA MICROCOMPUTER : The power supply is shown with the marked box. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 22 1 2 3 4 1 2 3 4 C D F A B E A-a A-b A-b 2/2 2 4 3 1 > AUDIO SELECTOR VDD 3.3V REGULATOR 5V REGULATOR ACC SENSE BACKUP SENSE AUDIO 8V REGULATOR DAC 5V REGULATOR 3.3V/6V DUAL DC/DC CONVERTER N BACKUP > 2A GND ACC MAIN UNIT(SYSCOM) 2/2 A www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 23 5 6 7 8 5 6 7 8 C D F A B E A-a A-b A-b 2/2 5 > > ROCOMPUTER IP-BUS DRIVER DATA COMMUNICATION DATA OUT IP-BUS OUT IP-BUS IN RESET www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 24 1 2 3 4 1 2 3 4 C D F A B E 3.4 TUNER UNIT B RF XM ANTENNA www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 25 5 6 7 8 5 6 7 8 C D F A B E B 1/2 A CN301 B TUNER UNIT CLK BUFFER www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 26 1 2 3 4 1 2 3 4 C D F A B E 4. PCB CONNECTION DIAGRAM 4.1 MAIN UNIT Capacitor Connector P.C.Board Chip Part A A MAIN UNIT SIDE B SIDE A NOTE FOR PCB DIAGRAMS 1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic dia- gram. 2.Viewpoint of PCB diagrams 10 20 30 40 50 60 70 X 10 20 30 40 50 60 70 80 90 100 110 120 130 0 Y B CN502 IP-BUS OUT www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 27 5 6 7 8 5 6 7 8 C D F A B E A SIDE A 70 80 90 100 110 120 130 140 150 160 170 FRONT CORD ASSY IP-BUS IN DATA OUT RESET www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 28 1 2 3 4 1 2 3 4 C D F A B E A A MAIN UNIT 90 100 110 120 130 140 150 160 170 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 29 5 6 7 8 5 6 7 8 C D F A B E A SIDE B 10 20 30 40 50 60 70 80 90 X 10 20 30 40 50 60 70 80 90 100 110 120 130 0 Y www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 30 1 2 3 4 1 2 3 4 C D F A B E 4.2 TUNER UNIT B B TUNER UNIT SIDE A 10 20 30 40 50 10 20 30 0 X Y A CN301 XM ANTENNA www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 31 5 6 7 8 5 6 7 8 C D F A B E B B TUNER UNIT SIDE B 10 20 30 40 50 10 20 30 0 X Y www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 32 1 2 3 4 1 2 3 4 C D F A B E 5. ELECTRICAL PARTS LIST NOTE: • Parts whose parts numbers are omitted are subject to being not supplied. • The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... • The > mark found on some component parts indicatesthe importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. • Meaning of the figures and others in the parentheses in the parts list. Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board. IC 301 (A, 91, 111) IC NJM2068V Circuit Symbol and No. Part No. A Unit Number:CWM9857 Unit Name:Main Unit MISCELLANEOUS IC 200 (A,34,92) IC STA850P IC 260 (A,34,122) IC K4S280832F-TC75 IC 300 (A,82,92) IC STA850P IC 360 (A,82,122) IC K4S280832F-TC75 IC 370 (A,55,118) IC ST19AF08BR20QMAA IC 401 (A,123,31) IC BA3131FS IC 403 (A,142,28) IC TA2050FS1 IC 451 (A,64,19) IC HA12240FP IC 452 (A,88,17) IC UPD4721GS IC 480 (A,118,79) IC PCM1742KE IC 490 (A,123,59) IC NJM4558MD IC 601 (A,66,51) IC PEG099A IC 603 (A,51,41) IC S-80827CNNB-B8M IC 605 (A,99,43) IC PEG100A IC 801 (A,141,67) IC S-T111B33MC-OGS IC 802 (A,142,43) IC NJM2880U1-05 IC 830 (A,113,105) IC PQ012FZ01ZP IC 841 (A,137,111) IC NJM2880U1-05 IC 842 (A,150,120) IC BA033CC0FP IC 851 (A,142,100) IC AN8011S Q 402 (A,52,36) Transistor 2SC4081 Q 403 (A,55,30) Transistor DTC144EU Q 404 (A,60,27) Transistor 2SA1162 Q 405 (A,56,26) Transistor UMH3N Q 451 (A,69,22) Transistor UMD2N Q 452 (A,77,26) Transistor UMD2N Q 453 (A,69,15) Transistor DTC144EU Q 454 (A,86,6) Transistor 2SC4081 Q 801 (A,145,58) Transistor 2SD1760F5 Q 802 (A,148,67) Transistor UMD2N Q 811 (A,156,43) Transistor 2SD1767 Q 812 (A,156,47) Transistor UMD2N Q 851 (A,118,90) Transistor 2SC4081 Q 852 (A,152,89) Transistor 2SC4081 Q 853 (A,127,90) Transistor 2SJ529S Q 854 (A,161,90) Transistor 2SJ529S Q 911 (A,149,35) Transistor IMX1 D 451 (A,96,16) Diode UDZS12(B) D 452 (A,96,18) Diode UDZS12(B) D 453 (A,102,22) Diode UDZS12(B) D 454 (A,102,20) Diode UDZS12(B) D 455 (A,92,7) Diode 1SS355 D 456 (A,66,10) Diode DAN202U D 457 (A,147,12) Diode UMZ6R8N D 458 (A,147,15) Diode UMZ6R8N D 459 (A,143,12) Diode UMZ6R8N D 460 (A,143,15) Diode UMZ6R8N D 801 (A,163,65) Diode 1SR154-400 D 802 (A,151,54) Diode UDZS5R6(B) D 811 (A,154,48) Diode UDZS9R1(B) D 851 (A,168,65) Diode RB051L-40 D 853 (A,118,94) Diode 1SS355 D 854 (A,151,94) Diode 1SS355 D 855 (A,135,89) Diode RSX201L-30 D 856 (A,161,84) Diode RSX201L-30 D 901 (A,156,36) Diode 1SR154-400 D 911 (A,155,30) Diode UDZS7R5(B) D 912 (A,155,26) Diode UDZS6R8(B) L 201 (A,49,104) Inductor CTF1306 L 202 (A,51,104) Inductor CTF1306 L 203 (A,16,80) Inductor CTF1306 L 204 (A,19,81) Inductor CTF1306 L 205 (A,33,104) Ferrite Bead CTF1528 L 207 (A,23,77) Ferrite Bead CTF1528 L 208 (A,19,115) Inductor CTF1306 L 209 (A,26,77) Ferrite Bead CTF1528 L 301 (A,8,65) Inductor LCYB27NJ1005 L 302 (A,98,110) Inductor CTF1306 L 303 (A,99,107) Inductor CTF1306 L 304 (A,95,77) Inductor CTF1473 L 305 (A,65,80) Inductor CTF1306 L 306 (A,67,80) Inductor CTF1306 L 309 (A,82,104) Ferrite Bead CTF1528 L 311 (A,67,117) Inductor CTF1306 Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 33 5 6 7 8 5 6 7 8 C D F A B E L 312 (A,99,98) Ferrite Bead CTF1528 L 313 (A,97,97) Ferrite Bead CTF1528 L 314 (A,97,96) Ferrite Bead CTF1528 L 315 (A,97,95) Ferrite Bead CTF1528 L 316 (A,97,94) Ferrite Bead CTF1528 L 317 (A,62,115) Ferrite Bead CTF1528 L 318 (A,97,88) Chip Bead VTL1128 L 319 (A,97,87) Chip Bead VTL1128 L 320 (A,97,86) Chip Bead VTL1128 L 321 (A,97,85) Chip Bead VTL1128 L 322 (A,62,126) Inductor CTF1306 L 323 (A,77,75) Ferrite Bead CTF1528 L 324 (A,89,78) Ferrite Bead CTF1528 L 325 (A,90,77) Ferrite Bead CTF1528 L 326 (A,77,74) Ferrite Bead CTF1528 L 327 (A,41,66) Inductor CTF1306 L 328 (A,44,66) Inductor CTF1306 L 451 (A,68,19) Inductor CTF1473 L 452 (A,80,20) Inductor CTF1473 L 453 (A,96,19) Inductor CTF1334 L 454 (A,96,21) Inductor CTF1334 L 480 (A,121,73) Inductor CTF1473 L 481 (A,120,73) Inductor CTF1473 L 602 (A,69,39) Inductor CTF1473 L 603 (A,95,56) Inductor CTF1473 L 851 (A,152,76) Inductor CTH1253 L 852 (A,146,90) Inductor LCYA100J2520 L 853 (A,123,102) Inductor CTH1262 L 854 (A,161,101) Inductor CTH1262 L 901 (A,166,36) Choke Coil 1.4mH CTH1129 X 601 (A,100,60) Resonator 16.77Hz CSS1686 X 602 (A,62,36) Resonator 10.00Hz CSS1685 S 602 (A,117,7) Switch(RESET) CSG1046 > FU451 (A,106,18) Fuse 2A CEK1284 > FU452 (A,108,16) Fuse 2A CEK1284 > FU851 (A,162,69) Fuse 2A CEK1284 > FU854 (A,120,110) Fuse 2A CEK1284 > FU855 (A,155,107) Fuse 1A CEK1280 RESISTORS R 200 (A,15,98) RS1/16SS102J R 201 (A,13,88) RS1/16SS102J R 202 (A,15,97) RS1/16SS102J R 203 (A,14,88) RS1/16SS102J R 204 (A,21,78) RS1/16SS223J R 205 (A,24,78) RS1/16SS223J R 206 (A,20,102) RS1/16SS3002F R 207 (A,19,101) RS1/16SS2002F R 208 (A,18,98) RS1/16S0R0J R 209 (A,25,107) RAB4CQ470J R 210 (A,28,107) RAB4CQ470J R 211 (A,30,108) RAB4CQ470J R 212 (A,35,105) RS1/16SS470J R 213 (A,22,107) RS1/16SS0R0J R 214 (A,41,77) RS1/16S822J R 215 (A,18,93) RS1/16SS0R0J R 216 (A,20,93) RS1/16SS0R0J R 217 (A,18,92) RS1/16SS0R0J R 218 (A,20,91) RS1/16SS0R0J Circuit Symbol and No. Part No. R 219 (A,35,109) RAB4CQ470J R 220 (A,45,77) RS1/16S822J R 221 (A,38,109) RAB4CQ470J R 222 (A,42,77) RS1/16S0R0J R 223 (A,44,77) RS1/16S0R0J R 224 (A,44,106) RS1/16SS470J R 225 (A,46,105) RAB4CQ470J R 227 (A,50,89) RS1/16S0R0J R 228 (A,29,77) RS1/16S0R0J R 229 (A,42,109) RS1/16S0R0J R 230 (A,47,84) RS1/16SS103J R 231 (A,47,85) RS1/16SS103J R 232 (A,47,86) RS1/16SS103J R 233 (A,47,88) RS1/16SS103J R 234 (A,47,92) RS1/16SS103J R 300 (A,61,98) RS1/16SS102J R 301 (A,60,88) RS1/16SS102J R 302 (A,61,97) RS1/16SS102J R 303 (A,61,88) RS1/16SS102J R 304 (A,64,101) RS1/16SS4701F R 305 (A,65,102) RS1/16SS3301F R 306 (A,64,104) RS1/16SS0R0J R 307 (A,67,103) RS1/16SS470J R 308 (A,73,78) RS1/16SS512J R 309 (A,71,105) RS1/16SS470J R 310 (A,74,107) RAB4CQ470J R 311 (A,76,107) RAB4CQ470J R 312 (A,79,107) RAB4CQ470J R 313 (A,84,105) RS1/16SS470J R 314 (A,97,102) RS1/16S0R0J R 315 (A,84,109) RAB4CQ470J R 316 (A,87,109) RAB4CQ470J R 317 (A,87,78) RS1/16S0R0J R 318 (A,88,78) RS1/16S0R0J R 319 (A,99,78) RS1/16SS0R0J R 320 (A,93,106) RS1/16SS470J R 321 (A,95,106) RAB4CQ470J R 322 (A,97,78) RS1/16SS102J R 323 (A,71,106) RS1/16SS0R0J R 324 (A,70,102) RS1/16SS0R0J R 325 (A,65,93) RS1/16SS0R0J R 326 (A,67,93) RS1/16SS0R0J R 327 (A,67,92) RS1/16SS0R0J R 328 (A,90,109) RS1/16S0R0J R 329 (A,99,92) RS1/16S0R0J R 330 (A,80,76) RS1/16S0R0J R 331 (A,97,81) RS1/16SS103J R 332 (A,97,83) RS1/16SS103J R 333 (A,97,84) RS1/16SS103J R 334 (A,97,89) RS1/16SS103J R 335 (A,95,91) RS1/16SS103J R 336 (A,65,91) RS1/16SS0R0J R 338 (A,61,101) RS1/16SS330J R 339 (A,71,107) RS1/16SS470J R 340 (A,71,108) RS1/16SS470J R 341 (A,22,106) RS1/16SS470J R 342 (A,22,108) RS1/16SS470J R 343 (A,22,109) RS1/16SS470J R 344 (A,68,97) RS1/16S0R0J R 346 (A,97,101) RS1/16S0R0J Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 34 1 2 3 4 1 2 3 4 C D F A B E R 347 (A,97,99) RS1/16S0R0J R 370 (A,62,117) RS1/16SS103J R 371 (A,62,122) RS1/16S472J R 372 (A,63,122) RS1/16S472J R 375 (A,62,114) RS1/16S0R0J R 390 (A,58,101) RS1/16SS0R0J R 401 (A,118,41) RS1/16S103J R 402 (A,118,25) RS1/16S103J R 403 (A,118,38) RS1/16S473J R 404 (A,119,25) RS1/16S473J R 405 (A,125,38) RS1/16S103J R 406 (A,126,25) RS1/16S103J R 407 (A,120,38) RS1/16S473J R 408 (A,121,25) RS1/16S473J R 409 (A,123,38) RS1/16S562J R 410 (A,124,25) RS1/16S562J R 411 (A,122,38) RS1/16S473J R 412 (A,123,25) RS1/16S473J R 413 (A,127,25) RS1/16S473J R 415 (A,50,36) RS1/16S473J R 416 (A,48,36) RS1/16S102J R 417 (A,129,36) RS1/16S473J R 418 (A,130,25) RS1/16S473J R 419 (A,61,30) RS1/16S103J R 420 (A,58,30) RS1/16S333J R 421 (A,65,13) RS1/16S101J R 422 (A,64,13) RS1/16S101J R 423 (A,51,23) RS1/16S102J R 424 (A,60,23) RS1/16S102J R 425 (A,148,21) RS1/16S102J R 426 (A,142,18) RS1/16S102J R 427 (A,57,23) RS1/16S223J R 428 (A,56,23) RS1/16S223J R 429 (A,148,18) RS1/16S223J R 430 (A,143,18) RS1/16S223J R 431 (A,146,18) RS1/16S181J R 432 (A,145,18) RS1/16S181J R 433 (A,71,31) RS1/16S473J R 451 (A,70,19) RS1/16S103J R 453 (A,81,15) RS1/16S101J R 454 (A,96,23) RS1/16S101J R 455 (A,101,19) RS1/16S681J R 456 (A,102,17) RS1/16S681J R 457 (A,86,23) RS1/16S101J R 458 (A,88,23) RS1/16S101J R 459 (A,87,10) RS1/16S333J R 460 (A,90,8) RS1/16S333J R 461 (A,90,7) RS1/16S333J R 462 (A,90,5) RS1/16S333J R 480 (A,110,68) RS1/16S0R0J R 481 (A,102,82) RS1/16S470J R 482 (A,99,87) RS1/16SS470J R 483 (A,99,88) RS1/16SS470J R 484 (A,102,86) RS1/16S470J R 485 (A,116,66) RS1/16S0R0J R 486 (A,111,83) RS1/16S101J R 487 (A,111,84) RS1/16S101J R 488 (A,111,86) RS1/16S101J R 489 (A,111,87) RS1/16S473J R 490 (A,131,61) RS1/16S103J Circuit Symbol and No. Part No. R 491 (A,115,60) RS1/16S103J R 492 (A,131,56) RS1/16S103J R 493 (A,115,56) RS1/16S103J R 494 (A,131,58) RS1/16S103J R 495 (A,115,58) RS1/16S103J R 496 (A,118,61) RS1/16S473J R 497 (A,128,61) RS1/16S473J R 601 (A,86,41) RS1/16S473J R 602 (A,87,39) RS1/16S473J R 603 (A,68,32) RS1/16S473J R 604 (A,62,40) RS1/16S0R0J R 605 (A,105,53) RS1/16S473J R 606 (A,101,32) RS1/16S473J R 608 (A,113,28) RS1/16S104J R 610 (A,78,42) RS1/16S473J R 611 (A,78,45) RS1/16S473J R 612 (A,81,56) RS1/16S473J R 613 (A,79,53) RS1/16S473J R 614 (A,79,56) RS1/16S473J R 615 (A,81,62) RS1/16S473J R 617 (A,51,44) RS1/16S183J R 618 (A,54,44) RS1/16S102J R 619 (A,62,64) RS1/16S473J R 620 (A,60,64) RS1/16S473J R 621 (A,59,64) RS1/16S473J R 622 (A,55,38) RS1/16S473J R 623 (A,63,64) RS1/16S473J R 625 (A,49,62) RS1/16S104J R 629 (A,92,56) RS1/16S473J R 630 (A,101,55) RS1/16S0R0J R 631 (A,81,49) RS1/16S101J R 632 (A,78,50) RS1/16S101J R 633 (A,53,45) RS1/16S101J R 634 (A,53,47) RS1/16S101J R 635 (A,53,53) RS1/16S101J R 636 (A,81,55) RS1/16S101J R 637 (A,53,55) RS1/16S101J R 638 (A,65,64) RS1/16S101J R 639 (A,69,64) RS1/16S101J R 640 (A,70,64) RS1/16S101J R 641 (A,78,61) RS1/16S101J R 642 (A,78,59) RS1/16S101J R 643 (A,82,59) RS1/16S101J R 644 (A,78,52) RS1/16S101J R 645 (A,81,51) RS1/16S101J R 646 (A,78,44) RS1/16S101J R 647 (A,78,47) RS1/16S101J R 649 (A,74,31) RS1/16S101J R 650 (A,82,46) RS1/16S101J R 651 (A,88,52) RS1/16S101J R 652 (A,87,49) RS1/16S101J R 653 (A,87,48) RS1/16S101J R 656 (A,81,48) RS1/16S473J R 657 (A,53,52) RS1/16S101J R 658 (A,87,45) RS1/16S101J R 659 (A,86,42) RS1/16S101J R 665 (A,89,55) RS1/16S101J R 666 (A,82,28) RS1/16S473J R 669 (A,99,55) RS1/16S105J R 801 (A,150,59) RS1/16S272J Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 35 5 6 7 8 5 6 7 8 C D F A B E R 802 (A,150,58) RS1/16S223J R 804 (A,155,56) RS1/16S360J R 805 (A,155,54) RS1/16S360J R 811 (A,159,44) RS1/16S182J R 847 (A,7,59) RS1/16S0R0J R 848 (A,8,53) RS1/16S0R0J R 851 (A,133,101) RS1/16S2701D R 852 (A,133,100) RS1/16S0R0J R 853 (A,132,98) RS1/16S1801D R 854 (A,132,97) RS1/16S8200D R 855 (A,137,100) RS1/16S1203D R 856 (A,136,102) RS1/16S2701D R 857 (A,136,93) RS1/16S221J R 859 (A,135,106) RS1/16S6801D R 860 (A,137,106) RS1/16S6801D R 861 (A,136,98) RS1/16S0R0J R 862 (A,148,94) RS1/16S221J R 863 (A,151,98) RS1/16S3901D R 864 (A,151,101) RS1/16S3302D R 865 (A,151,100) RS1/16S0R0J R 866 (A,149,97) RS1/16S2002D R 867 (A,147,100) RS1/16S2203D R 868 (A,148,102) RS1/16S2701D R 869 (A,151,97) RS1/16S4701D R 870 (A,148,105) RS1/16S1502D R 871 (A,151,105) RS1/16S6801D R 872 (A,149,105) RS1/16S0R0J R 873 (A,117,92) RS1/16S272J R 874 (A,121,94) RS1/16S0R0J R 875 (A,152,92) RS1/16S272J R 876 (A,155,94) RS1/16S0R0J R 879 (A,160,79) RS1/16S360J R 880 (A,160,81) RS1/16S360J R 881 (A,145,71) RS1/16S360J R 882 (A,145,73) RS1/16S360J R 913 (A,152,32) RS1/16S103J R 914 (A,152,30) RS1/16S473J R 915 (A,155,28) RS1/16S472J R 916 (A,152,26) RS1/16S103J R 917 (A,152,27) RS1/16S473J CAPACITORS C 200 (A,12,93) CKSSYB103K16 C 201 (A,13,90) CKSSYB103K16 C 202 (A,12,92) CKSSYB103K16 C 203 (A,12,91) CKSSYB103K16 C 204 (A,12,79) CEVW100M16 C 205 (A,13,95) CKSRYB105K6R3 C 206 (A,15,85) CKSRYB105K6R3 C 207 (A,16,94) CKSSYB104K10 C 208 (A,17,85) CKSSYB104K10 C 209 (A,16,90) CKSSYB104K10 C 210 (A,18,86) CKSSYB104K10 C 211 (A,18,85) CKSSYB104K10 C 212 (A,18,84) CKSSYB104K10 C 213 (A,18,83) CKSSYB104K10 C 214 (A,15,95) CCSRCH180J50 C 215 (A,14,85) CCSRCH180J50 C 216 (A,21,82) CKSSYB104K10 Circuit Symbol and No. Part No. C 217 (A,18,103) CKSSYB104K10 C 218 (A,18,100) CKSRYB105K6R3 C 219 (A,22,78) CKSSYB103K16 C 220 (A,23,78) CKSSYB103K16 C 221 (A,18,94) CCSSCH101J50 C 222 (A,17,94) CKSSYB104K10 C 223 (A,19,94) CCSSCH101J50 C 224 (A,20,94) CKSSYB104K10 C 225 (A,20,90) CCSSCH101J50 C 226 (A,19,90) CKSSYB104K10 C 227 (A,17,90) CCSSCH101J50 C 228 (A,18,90) CKSSYB104K10 C 229 (A,21,84) CKSSYB104K10 C 230 (A,18,101) CKSSYB104K10 C 231 (A,28,79) CKSSYB104K10 C 232 (A,28,105) CKSSYB104K10 C 233 (A,32,107) CKSRYB105K6R3 C 234 (A,33,79) CKSSYB104K10 C 235 (A,33,77) CKSRYB105K6R3 C 236 (A,34,106) CKSSYB104K10 C 237 (A,36,79) CKSSYB104K10 C 238 (A,37,77) CSZS100M6R3 C 239 (A,41,106) CSZS100M6R3 C 240 (A,40,105) CKSSYB104K10 C 241 (A,47,82) CKSSYB104K10 C 242 (A,47,99) CKSSYB104K10 C 243 (A,47,94) CKSSYB104K10 C 244 (A,47,90) CKSSYB104K10 C 245 (A,49,89) CSZS100M6R3 C 246 (A,48,94) CKSRYB105K6R3 C 247 (A,18,96) CKSQYB475K6R3 C 248 (A,17,88) CKSQYB475K6R3 C 251 (A,51,106) CSZS100M6R3 C 252 (A,16,103) CCSSCH100D50 C 253 (A,10,88) CCSSCH4R0C50 C 254 (A,10,90) CCSSCH4R0C50 C 255 (A,10,92) CCSSCH4R0C50 C 256 (A,10,93) CCSSCH4R0C50 C 257 (A,21,103) CKSSYB104K10 C 258 (A,34,105) CKSSYB104K10 C 259 (A,36,130) CCSSCH220J50 C 260 (A,20,120) CEVW100M16 C 261 (A,24,114) CKSSYB104K10 C 262 (A,26,114) CKSSYB104K10 C 263 (A,30,114) CKSSYB104K10 C 264 (A,33,114) CKSSYB104K10 C 265 (A,46,114) CKSSYB104K10 C 266 (A,28,130) CKSSYB104K10 C 267 (A,33,130) CKSSYB104K10 C 268 (A,23,114) CCSSCH220J50 C 269 (A,27,114) CCSSCH220J50 C 270 (A,29,114) CCSSCH220J50 C 271 (A,32,114) CCSSCH220J50 C 272 (A,35,114) CCSSCH220J50 C 273 (A,36,114) CCSSCH220J50 C 274 (A,37,114) CCSSCH220J50 C 275 (A,38,114) CCSSCH220J50 C 276 (A,39,114) CCSSCH220J50 C 277 (A,40,114) CCSSCH220J50 C 278 (A,41,114) CCSSCH220J50 Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 36 1 2 3 4 1 2 3 4 C D F A B E C 279 (A,42,114) CCSSCH220J50 C 280 (A,43,114) CCSSCH220J50 C 281 (A,44,114) CCSSCH220J50 C 282 (A,45,114) CCSSCH220J50 C 283 (A,25,130) CCSSCH220J50 C 284 (A,27,130) CCSSCH220J50 C 285 (A,29,130) CCSSCH220J50 C 286 (A,31,130) CCSSCH220J50 C 290 (A,39,130) CCSSCH220J50 C 291 (A,40,130) CCSSCH220J50 C 292 (A,41,130) CCSSCH220J50 C 293 (A,42,130) CCSSCH220J50 C 294 (A,43,130) CCSSCH220J50 C 295 (A,44,130) CCSSCH220J50 C 296 (A,45,130) CCSSCH220J50 C 299 (A,37,130) CCSSCH220J50 C 300 (A,59,93) CKSSYB103K16 C 301 (A,60,90) CKSSYB103K16 C 303 (A,59,92) CKSSYB103K16 C 304 (A,59,91) CKSSYB103K16 C 305 (A,62,101) CCSSCH100D50 C 306 (A,61,81) CEVW100M16 C 307 (A,72,75) CKSRYB224K10 C 308 (A,59,95) CKSRYB105K6R3 C 309 (A,61,86) CKSRYB105K6R3 C 310 (A,62,95) CKSSYB104K10 C 311 (A,65,85) CKSSYB104K10 C 312 (A,63,90) CKSSYB104K10 C 313 (A,66,86) CKSSYB104K10 C 314 (A,66,85) CKSSYB104K10 C 315 (A,66,84) CKSSYB104K10 C 316 (A,66,83) CKSSYB104K10 C 317 (A,70,80) CKSSYB103K16 C 318 (A,71,78) CKSSYB103K16 C 319 (A,61,95) CCSRCH180J50 C 320 (A,63,86) CCSRCH180J50 C 321 (A,69,83) CKSSYB104K10 C 322 (A,63,101) CKSSYB104K10 C 323 (A,67,99) CKSRYB105K6R3 C 324 (A,63,95) CCSSCH101J50 C 325 (A,64,95) CKSSYB104K10 C 326 (A,65,95) CCSSCH101J50 C 327 (A,66,95) CKSSYB104K10 C 328 (A,67,90) CCSSCH101J50 C 329 (A,66,90) CKSSYB104K10 C 330 (A,65,90) CCSSCH101J50 C 331 (A,64,90) CKSSYB104K10 C 332 (A,69,85) CKSSYB104K10 C 333 (A,68,98) CKSSYB104K10 C 334 (A,76,79) CKSSYB104K10 C 335 (A,77,104) CKSSYB104K10 C 336 (A,81,107) CKSRYB105K6R3 C 337 (A,81,79) CKSSYB104K10 C 338 (A,80,77) CKSRYB105K6R3 C 339 (A,83,106) CKSSYB104K10 C 340 (A,85,78) CKSSYB104K10 C 341 (A,83,77) CSZS100M6R3 C 342 (A,90,106) CSZS100M6R3 C 343 (A,88,104) CKSSYB104K10 C 344 (A,92,78) CKSSYB104K10 Circuit Symbol and No. Part No. C 345 (A,93,77) CSZS100M6R3 C 346 (A,96,81) CKSSYB104K10 C 347 (A,96,78) CKSSYB471K50 C 348 (A,95,98) CKSSYB104K10 C 349 (A,95,93) CKSSYB104K10 C 350 (A,97,79) CKSRYB472K50 C 351 (A,97,90) CKSSYB104K10 C 352 (A,100,90) CSZS100M6R3 C 353 (A,96,93) CKSRYB105K6R3 C 354 (A,64,96) CKSQYB475K6R3 C 355 (A,66,88) CKSQYB475K6R3 C 357 (A,68,102) CCSSCH100D50 C 358 (A,9,63) CCSRCH180J50 C 359 (A,7,63) CCSRCH180J50 C 360 (A,68,122) CEVW100M16 C 361 (A,94,114) CKSSYB104K10 C 362 (A,72,114) CKSSYB104K10 C 363 (A,74,114) CKSSYB104K10 C 364 (A,78,114) CKSSYB104K10 C 365 (A,81,114) CKSSYB104K10 C 366 (A,76,130) CKSSYB104K10 C 367 (A,81,130) CKSSYB104K10 C 370 (A,62,119) CKSRYB102K50 C 371 (A,56,129) CEVW100M16 C 372 (A,56,126) CKSSYB104K10 C 373 (A,71,114) CCSSCH220J50 C 374 (A,75,114) CCSSCH220J50 C 375 (A,77,114) CCSSCH220J50 C 376 (A,80,114) CCSSCH220J50 C 377 (A,83,114) CCSSCH220J50 C 378 (A,84,114) CCSSCH220J50 C 379 (A,85,114) CCSSCH220J50 C 380 (A,86,114) CCSSCH220J50 C 381 (A,87,114) CCSSCH220J50 C 382 (A,88,114) CCSSCH220J50 C 383 (A,89,114) CCSSCH220J50 C 384 (A,90,114) CCSSCH220J50 C 385 (A,91,114) CCSSCH220J50 C 386 (A,92,114) CCSSCH220J50 C 387 (A,93,114) CCSSCH220J50 C 388 (A,93,130) CCSSCH220J50 C 389 (A,92,130) CCSSCH220J50 C 390 (A,91,130) CCSSCH220J50 C 391 (A,90,130) CCSSCH220J50 C 392 (A,89,130) CCSSCH220J50 C 393 (A,88,130) CCSSCH220J50 C 394 (A,87,130) CCSSCH220J50 C 398 (A,79,130) CCSSCH220J50 C 399 (A,77,130) CCSSCH220J50 C 400 (A,75,130) CCSSCH220J50 C 401 (A,73,130) CCSSCH220J50 C 402 (A,57,88) CCSSCH4R0C50 C 403 (A,125,45) CEVW470M16 C 404 (A,57,90) CCSSCH4R0C50 C 405 (A,119,46) CEVW220M16 C 406 (A,133,45) CEVW101M16 C 407 (A,133,37) CEVWNP100M10 C 408 (A,134,25) CEVWNP100M10 C 409 (A,57,92) CCSSCH4R0C50 C 410 (A,141,36) CEVW220M16 Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 37 5 6 7 8 5 6 7 8 C D F A B E C 411 (A,65,28) CEVW100M16 C 412 (A,50,28) CEVW100M16 C 413 (A,147,21) 1µF CCG1207 C 414 (A,143,21) 1µF CCG1207 C 415 (A,145,21) 1µF CCG1207 C 416 (A,142,21) 1µF CCG1207 C 417 (A,125,12) CKSRYB104K25 C 418 (A,133,31) CEVW220M16 C 419 (A,38,130) CCSSCH220J50 C 420 (A,57,94) CCSSCH4R0C50 C 425 (A,14,105) CKSSYB104K10 C 427 (A,65,76) CKSSYB104K10 C 433 (A,83,105) CKSSYB104K10 C 434 (A,6,63) CKSSYB104K10 C 435 (A,84,130) CCSSCH220J50 C 436 (A,85,130) CCSSCH220J50 C 437 (A,102,80) CCSRCH470J50 C 438 (A,100,84) CCSRCH470J50 C 439 (A,101,81) CCSSCH470J50 C 440 (A,101,88) CCSSCH470J50 C 441 (A,86,130) CCSSCH220J50 C 451 (A,70,12) CKSRYB104K25 C 452 (A,68,12) CKSRYB102K50 C 453 (A,62,13) CKSRYB102K50 C 454 (A,78,18) 10000pF CCG1171 C 455 (A,82,20) 1µF CCG1207 C 456 (A,85,23) 1µF CCG1207 C 457 (A,81,16) 1µF CCG1207 C 458 (A,91,23) 1µF CCG1207 C 459 (A,89,23) 1µF CCG1207 C 460 (A,99,16) CKSRYB102K50 C 461 (A,99,20) CKSRYB102K50 C 462 (A,78,21) CKSSYB104K10 C 463 (A,90,11) CKSRYB104K25 C 465 (A,93,19) CKSSYB104K10 C 480 (A,118,75) CKSSYB104K10 C 481 (A,125,77) CSZS100M16 C 482 (A,116,71) CEVW100M16 C 483 (A,122,76) CKSSYB103K16 C 484 (A,126,82) CEVW100M16 C 485 (A,122,83) CKSSYB104K10 C 486 (A,119,70) CKSSYB104K10 C 487 (A,120,70) CKSSYB104K10 C 488 (A,123,77) CKSRYB105K10 C 490 (A,128,66) CEVW100M16 C 491 (A,123,66) CEVW100M16 C 492 (A,131,60) CKSRYB152K50 C 493 (A,115,61) CKSRYB152K50 C 494 (A,128,57) CKSRYB221K50 C 495 (A,117,57) CKSRYB221K50 C 497 (A,121,55) CKSRYB104K25 C 601 (A,65,38) CCSRCH120J50 C 602 (A,62,38) CCSRCH120J50 C 603 (A,93,56) CKSRYB104K25 C 604 (A,71,36) CEVW100M16 C 605 (A,53,41) CKSRYB104K25 C 607 (A,69,40) CKSRYB104K25 C 608 (A,99,57) CCSRCH100D50 C 609 (A,101,57) CCSRCH100D50 C 610 (A,91,60) CEVW100M16 Circuit Symbol and No. Part No. C 611 (A,53,50) CKSRYB104K25 C 612 (A,49,41) CKSRYB104K25 C 613 (A,67,64) CKSRYB104K25 C 615 (A,114,36) CKSSYB104K10 C 616 (A,110,46) CKSRYB104K25 C 617 (A,105,55) CKSRYB102K50 C 618 (A,98,32) CKSRYB104K25 C 619 (A,90,56) CKSRYB102K50 C 620 (A,49,55) CCSRCH100D50 C 621 (A,49,50) CCSRCH100D50 C 622 (A,66,66) CKSSYB104K10 C 623 (A,68,66) CKSSYB104K10 C 624 (A,106,65) CKSSYB103K16 C 801 (A,155,64) CEAT102M16(P35) C 802 (A,150,56) CKSRYB103K50 C 803 (A,136,59) CEAT471M16(P35) C 804 (A,140,64) CKSRYB103K50 C 805 (A,144,67) CKSRYB104K25 C 807 (A,138,67) CKSQYB475K6R3 C 808 (A,136,66) CKSRYB103K50 C 811 (A,149,48) CEVW100M16 C 812 (A,152,47) CKSRYB104K25 C 813 (A,149,41) CEVW220M16 C 814 (A,153,43) CKSRYB104K25 C 815 (A,144,46) CKSRYB104K25 C 816 (A,141,50) CEVW100M16 C 817 (A,141,46) CKSRYB473K50 C 832 (A,109,110) CKSRYB103K50 C 833 (A,110,118) CEVW101M6R3 C 836 (A,115,114) 1µF CCG1207 C 841 (A,9,59) CKSQYB475K6R3 C 842 (A,133,117) CEVW100M16 C 843 (A,141,112) CKSRYB104K25 C 844 (A,155,128) CKSRYB103K50 C 845 (A,161,124) CEVW101M16 C 846 (A,152,114) CKSYB475K10 C 847 (A,145,115) CKSRYB104K25 C 848 (A,152,112) CKSRYB104K25 C 849 (A,142,117) CEVW100M16 C 850 (A,133,112) CKSRYB103K50 C 851 (A,139,76) 470µF/25V CCH1337(P35) C 852 (A,166,76) 470µF/25V CCH1337(P35) C 853 (A,143,93) CKSRYB104K25 C 854 (A,142,91) CKSYB475K16 C 855 (A,142,88) CKSYB475K16 C 857 (A,149,98) CKSRYB104K25 C 858 (A,133,103) CKSRYB473K50 C 859 (A,135,100) CKSRYB104K25 C 860 (A,139,107) CCSSCH101J50 C 861 (A,151,103) CKSRYB103K50 C 862 (A,149,100) CKSRYB223K50 C 863 (A,144,107) CKSQYB475K6R3 C 864 (A,118,87) CKSYB225K16 C 865 (A,124,116) 470µF/25V CCH1337(P35) C 866 (A,152,87) CKSYB225K16 C 867 (A,161,113) 470µF/25V CCH1337(P35) C 870 (A,9,53) CKSSYB104K10 C 871 (A,137,118) CKSYB475K10 C 872 (A,138,44) CKSYB475K10 C 901 (A,163,57) CEAT471M16(P35) Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 38 1 2 3 4 1 2 3 4 C D F A B E C 902 (A,153,37) CKSRYB104K25 B Unit Number:CWE1933 Unit Name:Tuner Unit MISCELLANEOUS IC 501 (A,30,22) IC MAX2140ETH IC 502 (A,45,21) IC MAX999EUK D 501 (A,16,28) Diode HZU5R6(B3) D 502 (A,18,30) Diode HZU5R6(B3) D 503 (A,16,19) Diode HZU5R6(B3) L 501 (A,16,25) Inductor LCMA27NJ1608 L 502 (A,19,19) Inductor CTF1657 L 504 (A,19,22) Inductor LCYBR22J1608 L 505 (A,23,22) Inductor LCYB56NJ1005 L 506 (A,23,21) Inductor LCYB56NJ1005 L 507 (A,19,7) Inductor CTF1657 L 508 (A,35,12) Inductor LCYB27NJ1005 L 509 (A,35,11) Inductor LCYB27NJ1005 L 510 (A,33,15) Inductor LCYBR22J1608 L 511 (A,35,31) Inductor LCYB27NJ1005 L 512 (A,35,30) Inductor LCYB27NJ1005 L 513 (A,36,20) Inductor LCYBR22J1608 L 516 (A,30,12) Inductor LCYB27NJ1608 L 517 (A,29,12) Inductor LCMA27NJ1608 L 518 (A,46,24) Chip Bead VTL1128 L 519 (A,44,16) Ferrite Bead CTF1528 L 520 (A,30,15) Inductor LCMA47NJ1608 X 501 (A,35,7) Resonator 23.92Hz CSS1676 F 502 (A,19,13) Filter CTF1649 F 501 (A,20,26) Filter CTF1648 RESISTORS R 502 (A,27,30) RS1/16SS103J R 503 (A,28,30) RS1/16SS103J R 509 (A,37,21) RS1/16SS201J R 511 (A,44,18) RS1/16SS0R0J R 512 (A,43,20) RS1/16SS2701F R 513 (A,43,23) RS1/16SS2701F R 514 (A,42,23) RS1/16SS2002F R 515 (A,42,21) RS1/16SS2002F R 517 (A,45,8) RS1/16SS0R0J R 518 (A,44,26) RS1/16SS470J CAPACITORS C 501 (A,16,23) CCSSCH180J50 C 503 (A,17,18) CCSSCH121J50 C 505 (A,20,18) CCSSCH121J50 C 506 (A,21,23) 3.9pF CCG1128 C 509 (A,21,20) 3.9pF CCG1128 C 510 (A,17,23) CCSSCH221J50 C 511 (A,24,24) CCSSCH101J50 C 513 (A,20,8) CCSSCH101J50 C 514 (A,17,8) CCSSCH101J50 C 515 (A,23,19) CKSRYB224K10 C 516 (A,24,17) CCSSCH180J50 C 517 (A,26,27) CCSSCH101J50 C 518 (A,24,20) CCSSCH101J50 Circuit Symbol and No. Part No. C 521 (A,27,16) CKSSYB103K16 C 522 (A,26,16) CKSSYB103K16 C 523 (A,28,16) CKSSYB103K16 C 524 (A,30,16) CKSSYB103K16 C 525 (A,29,29) CKSSYB103K16 C 526 (A,29,27) CKSSYB103K16 C 527 (A,31,16) CKSSYB103K16 C 528 (A,31,27) CKSSYB103K16 C 529 (A,33,17) CCSSCH221J50 C 530 (A,33,18) CKSSYB103K16 C 531 (A,35,24) CCSSCH180J50 C 532 (A,37,13) CCSSCH180J50 C 533 (A,37,11) CCSSCH180J50 C 534 (A,35,27) CCSSCH180J50 C 535 (A,36,24) CKSSYB103K16 C 536 (A,35,28) 2.2µF CCG1179 C 537 (A,37,9) CCSSCH220J50 C 538 (A,35,23) CCSSCH101J50 C 539 (A,33,12) CKSSYB103K16 C 540 (A,33,11) CKSSYB103K16 C 541 (A,37,31) CCSSCH180J50 C 542 (A,37,29) CCSSCH180J50 C 543 (A,37,19) CKSSYB103K16 C 544 (A,37,20) CKSSYB103K16 C 545 (A,33,31) CKSSYB103K16 C 546 (A,33,30) CKSSYB103K16 C 547 (A,37,26) CKSSYB103K16 C 548 (A,35,18) CCSSCH180J50 C 550 (A,36,22) 2.2µF CCG1179 C 553 (A,37,23) CCSSCH180J50 C 554 (A,36,18) CKSSYB103K16 C 560 (A,44,24) CKSSYB103K16 C 561 (A,45,17) CKSSYB104K10 C 562 (A,45,18) CCSSCH180J50 C 563 (A,42,20) CKSSYB103K16 C 564 (A,31,12) CCSSCH180J50 C 565 (A,28,14) CCSSCH180J50 C 566 (A,30,10) CCSSCH180J50 C 567 (A,28,10) CCSSCH180J50 C 568 (A,46,25) CCSSCH100D50 C 569 (A,46,26) CCSSCH100D50 C 573 (A,43,15) CKSSYB104K10 C 574 (A,16,22) CCSSCH101J50 Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 39 5 6 7 8 5 6 7 8 C D F A B E 6. ADJUSTMENT 6.1 TEST MODE 4 6 B.UP ON ACC ON SOURCE [XM TUNER] Select the XM RADIO 1(*1) *1 : Less than 2 seconds. 1(*2) BER INFO *2 : 2 seconds or more. SAT1-BER-INFO 2(*1) 2(*2) LOCK-DETECT INFO SAT2-BER-INFO 3(*1) 3(*2) AGC INFO TERR-BER-INFO 4(*1) 4(*2) RS INFO MICRO Status 1 5(*1) 5(*2) TUNER INFO MICRO Status 2 6(*1) 6(*2) ERROR CODE ANTENNA PASS BAND 1(*1) 1(*2) QOS Message SSDEC Status 1 2(*1) 2(*2) TERR Message SSDEC Status 2 3(*1) 3(*2) SAT1 Message SSDEC Status 3 4(*1) 4(*2) SAT2 Message SSDEC Status 4 5(*1) Tuner Message 6(*2) MICRO VERSION BAND [ XM2 ] [ XM3 ] BAND [ XM1 ] 1(*1) 1(*2) SAT1 C/N SAT1 AFC 2(*1) 2(*2) SAT2 C/N SAT2 AFC 3(*1) 3(*2) SAT RSERR TERR AFC 4(*1) TERR RSERR 5(*1) AFC Check 6(*2) ANTENNA PASS The following head units are exceptional so that their entering ways to the test mode are different from others. Test mode starting procedure reset while pressing the 3 and 5 keys together. KEH-P4010/X1M/UC [ XM1 ] - Flow Chart 5(*2, *3) EXT DIAG *3 : Not for service. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 40 1 2 3 4 1 2 3 4 C D F A B E - Diagnostic mode 1. To Enter the Diagnostic mode Reset while pressing the 4 and 6 keys together. 2. To Exit from the Diagnostic mode Reset the system. 3. Contents of the Diagnostic mode General description Displays error rate of Viterbi decoding in ground wave, satellite wave 1, and satellite wave 2, respectively. (1 significant digit) Displays decoding LOCK in ground wave, satellite wave 1, and satellite wave 2, respectively. (MCM + TDM for ground wave, QPSK + TDM for satellite waves) AGC value of ground/satellite waves (3 decimal digits x 2) The number of error correction bytes of Read-Solomon decoding (4 hexadecimal digits) and the number of error frames (4 hexadecimal digits) Lock/Unlock information and synchronous ensemble (A/B) of PLL Error code for identifying error part Error rate of Viterbi decoding in satellite wave 1 (3 significant digits) Error rate of Viterbi decoding in satellite wave 2 (3 significant digits) Error rate of Viterbi decoding in ground wave (3 significant digits) System Operation Mode (2 hexadecimal digits) and XM Operation Mode 1 (2 hexadecimal digits) XM Operation Mode 2 (2 hexadecimal digits) and XM Operation Mode 3 (2 hexadecimal digits) Skips antenna unconnection check (Cancellable only by reset) Displays Quality of Service value (2 decimal digits) Lock/Unlock of decoding in ground wave and Viterbi decoding rate (2 significant decimal digits), RS error correction rate (2 significant decimal digits), and RS error rate (2 significant decimal digits) Lock/Unlock of decoding in satellite wave 1 and Viterbi decoding rate (2 significant decimal digits), RS error correction rate (2 significant decimal digits), and RS error rate (2 significant decimal digits) Lock/Unlock of decoding in satellite wave 2 and Viterbi decoding rate (2 significant decimal digits), RS error correction rate (2 significant decimal digits), and RS error rate (2 significant decimal digits) Information of LOCK/UNLOCK of PLL and information of ground/satellite antenna connection Synchronization/Asynchronization of PC receive, the number of overflow at the time of voice service data input, and the number of underflow at the time PCM output SSDEC general error code (6 significant hexadecimal digits) SSDEC service extract error code 1 (4 significant hexadecimal digits) SSDEC service extract error code 2 (4 significant hexadecimal digits) Microcomputer version C/N ratio in satellite wave 1 (dB) C/N ratio in satellite wave 2 (dB) AFC identification in ZIF tuner RS BLOCK #1/2 Error of satellite waves (2 decimal digits) RS BLOCK #1/2 Error of ground waves (2 decimal digits) AFC of satellite wave 1 in ZIF tuner AFC of satellite wave 2 in ZIF tuner AFC of ground wave in ZIF tuner XM Extended Diagnostic mode (Not for service) Skips antenna unconnection check (Cancellable only by reset) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 29 27 28 30 31 32 33 34 35 36 Mode number Mode name BER INFO LOCK-DETECT INFO AGC INFO RS INFO TUNER INFO ERROR CODE SAT1-BER-INFO SAT2-BER-INFO TERR-BER-INFO MICRO Status 1 MICRO Status 2 ANTENNA PASS QOS Message TERR Message SAT1 Message SAT2 Message Tuner Message Blank SSDEC Status 1 SSDEC Status 2 SSDEC Status 3 SSDEC Status 4 Blank MICRO VERSION SAT1 C/N SAT2 C/N AFC Check SAT RS ERR TERR RS ERR Blank SAT1 AFC SAT2 AFC TERR AFC Blank EXT DIAG ANTENNA PASS www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 41 5 6 7 8 5 6 7 8 C D F A B E 4. Details of the Diagnostic mode 4.1 BER INFO Display format : [ X X _ X X _ X X ] 12345678 1 : The Viterbi signal decryption error rate (effective value) for satellite wave 1. (*) 2 : The Viterbi signal decryption error rate (truncated binary exponential, with negative sign abbreviated) for satellite wave 1. (*) 3 : Spacing character. 4 : The Viterbi signal decryption error rate (effective value) for satellite wave 2. (*) 5 : The Viterbi signal decryption error rate (truncated binary exponential, with negative sign abbreviated) for satellite wave 2. (*) 6 : Spacing character. 7 : The Viterbi signal decryption error rate (effective value) for ground waves. (*) 8 : The Viterbi signal decryption error rate (truncated binary exponential, with negative sign abbreviated) for ground waves. (*) * : Each piece of information is effective following the initialization of CDEC. The updating interval is 432 ms. If not any of the modulated wave signals can be received (that is, the signal cannot be LOCKed), then a hyphen ("-") will be displayed. "If notany of the modulated wave signals can be received" it represents a condition that the modulated signals could not receive the signals described in section 4.2. Display example : If the satellite wave 1 = 10%, satellite wave 2 = 3.4% and ground wave = 0.23%, the display will show [ 1 1 _ 3 2 _ 2 3 ]. 4.2 LOCK-DETECT INFO Display format : [ X X _ X X _ X X ] 12345678 1 : The modulated QPSK signal of satellite wave 1 can be received (L) / cannot be received (-). 2 : The modulated TDM signal of satellite wave 1 can be received (L) / cannot be received (-). 3 : Spacing character. 4 : The modulated QPSK signal of satellite wave 2 can be received (L) / cannot be received (-). 5 : The modulated TDM signal of satellite wave 2 can be received (L) / cannot be received (-). 6 : Spacing character. 7 : The modulated MCM signal of ground wave can be received (L) / cannot be received (-). 8 : The modulated TDM signal of ground wave can be received (L) / cannot be received (-). Each piece of information is effective following the initialization of CDEC. The updating interval is 432 ms. Display example : If the QPSK signal of satellite wave, TDM signal of the satellite wave 2, and MCM signal of the ground wave are not locked, the display will show [ - L _ L - _ - L ]. 4.3 AGC INFO Display format : [ X X X _ Y Y Y _ ] X : The AGC signal count value of the satellite wave (three digits of a decimal value). Y : The AGC signal count value of the ground wave (three digits of a decimal value). Each piece of information becomes effective following the initialization of CDEC. The updating interval is 432 ms. Display example : If the satellite wave's AGC = 123, while the ground wave's AGC = 32, the display will show [ 1 2 3 _ 0 3 2 _ ]. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 42 1 2 3 4 1 2 3 4 C D F A B E 4.4 RS INFO Display format : [ X X X X Y Y Y Y ] X : Number of error correction bytes from Read-Solomon decryption (four digits of hexadecimal value). Y : Number of error frames from Read-Solomon decryption (four digits of hexadecimal value). Each piece of information becomes effective following the initialization of CDEC. The updating interval is 432 ms. Turn Integrating Mode ON/OFF by holding down “4” key while RS INFO is displayed. Reset integrating value by holding down “4” key while RS Integrating Mode is ON. Display example : If the error correction bytes = 0 x 0040, while the error frames = 0 x 0010, the display will show [ 0 0 4 0 0 0 1 0 ]. 4.5 TUNER INFO Display format : [ X _ Y Y Y Y _ Z ] X : Synchronous ensemble ( A / B ). _ : Spacing character. Y : LOCK/UNLOCK status of PLL ( L K _ _ / U N L K ). Z : RF AGC status of ZIF ( Engaged = 1 / Not Engaged = 0 ). The information becomes effective following the synchronization process during the system start up. The updating interval is 16 ms. Display example : If the PLL is locked with ensemble A, the display will show [ A _ L K _ _ _ 1 ]. 4.6 ERROR CODE Display format : [ E R R O R _ X X ] _ : Spacing character. X : Error occurring (two digits of hexadecimal value). The upper digit is for the major (physical) error, while the lower digit is for the minor error (temporary or partial errors). Refer to the following table for details: No minor error. The line for communicating with CDEC. The line for communicating with SSDEC. No SSDEC response (DSP core freeze). 100% error of Vitarbi signal decryption. Not activated. Not authorized. No major error. Antenna not connected. Short circuited antenna cable. PLL cannot be synchronized (RF circuit failure). Undefined. Defective NVM inside CAP. Defective CAP (including situations where CAP is not connected). Unknown DSP core software version. Defective DDC CAP not bound Code value Description Error location Major Minor 0 1 2 3 4 5 6 0 1 2 3 4 5 6 7 8 9 Display example : If the antenna is not connected, the display will show [ E R R O R _ 1 4 ] (no signal due to unconnected antenna). No Error CDEC Communication Error SSDEC Communication Error SSDEC No Response No Signal Activation Required Authorization Required No Error ANTENNA No Connect ANTENNA Short PLL UNLOCK Reserved NVM Error CAP Error Version Unknown DDC Fail Unbound www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 43 5 6 7 8 5 6 7 8 C D F A B E 4.7 SAT1-BER-INFO Display format : [ 1 _ X . X X E Y ] X : Viterbi signal decryption error rate (effective three digits). Y : Truncated binary exponential (with negative sign abbreviated) of the error rate. _ : Spacing character. The information becomes effective following the initialization of CDEC. The updating interval is 432 ms. If the wave's modulated signal cannot be received (meaning such a signal cannot be locked on), a hyphen ("-") will be displayed. Display example : If the error rate is 0.560%, the display will show [ 1 _ 5 . 6 0 E 3 ]. 4.8 SAT2-BER-INFO Display format : [ 2 _ X . X X E Y ] X : Viterbi signal decryption error rate (effective three digits). Y : Truncated binary exponential (with negative sign abbreviated) of the error rate. _ : Spacing character. The information becomes effective following the initialization of CDEC. The updating interval is 432 ms. If none of wave's modulated signal can be received (meaning such a signal cannot be locked on), a hyphen ("-") is displayed. Display example : If a signal cannot be locked on, the display will show [ 2 _ - - - - - - ]. 4.9 TERR-BER-INFO Display format : [ T _ X . X X E Y ] X : Viterbi signal decryption error rate (effective three digits). Y : Truncated binary exponential (with negative sign abbreviated) of the error rate. _ : Spacing character. The information will become effective following the initialization of CDEC. The updating interval is 432 ms. If the wave's modulated signal cannot be received (meaning such a signal cannot be locked on), a hyphen ("-") will be displayed. Display example : If the error rate is 0%, the display will show [ T _ 0 . 0 0 E 0 ]. 4.10 MICRO Status 1 Display format : [ M 1 _ X X _ Y Y ] X : System operation mode (two effective digits of hexadecimal value). Y : XM operation mode 1 (two effective digits of hexadecimal value). _ : Spacing character. System operation mode table Mode name Meaning STANDBY Under standby ENABLECHK Checking GaNET connection OFF ACC being ON and XM being OFF ANT_OFF Forcibly terminating because of antenna short-circuit ON_STANDBY Under Hot Standby ANT_ON Being ON at the time of antenna short-circuit ON XM being ON Mode number 00 05 10 11 12 21 2F www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 44 1 2 3 4 1 2 3 4 C D F A B E Mode number Mode name Meaning 00 HALT XM OFF completed 01 ON XM being ON 02 CHRD Recalling preset channel 03 CHWD Stores to preset channel 04 CHUP Preset channel being UP 05 CHDN Preset channel being DOWN 06 PROGUP Channel being UP 07 PROGDN Channel being DOWN 08 PROG10UP Channel rough being UP 09 PROG10DN Channel rough being DOWN 0E TRIGON Receive SID extinguished 10 RX Receiving 12 CHUP_WAIT Waiting for key release during preset channel being UP 13 CHDN_WAIT Waiting for key release during preset channel being DOWN 14 CHUP_REL Key release during preset channel being UP 15 CHDN_REL Key release during preset channel being DOWN 16 PROG10UP_WAIT Waiting for key release during channel rough being UP 17 PROG10DN_WAIT Waiting for key release during channel rough being DOWN 18 PROG10UP_REL Key release during channel rough being UP 19 PROG10DN_REL Key release during channel rough being DOWN 1A CATUP_WAIT Waiting for key release during category being UP 1B CATDN_WAIT Waiting for key release during category being DOWN 1C CATUP_REL Key release during category being UP 1D CATDN_REL Key release during category being DOWN 1E CATUP_LAST Searching last category being UP 1F CATDN_LAST Searching last category being DOWN 40 SCANUP Scanning channel 42 SCANUPHLD Holding channel scan 44 CATSCANUP Scanning category 46 CATSCANUPHLD Holding category scan 4C SCANSTOP Scan under suspension 4D IDCODE RADIO ID being displayed 4E PROGDIRECT Searching channel by dial operation 50 CATSSTEPUP Search UP in the category by dial operation 52 CATSSTEP_DN Search DOWN in the category by dial operation 53 CATUP_CRNT Searching receiving category being UP 54 CATDN_CRNT Searching receiving category being DOWN 55 REQCATS_UP Getting the name of channel in the category searched UP 56 REQCATS_DN Getting the name of channel in the category searched DOWN 60 STANDBY Starting Hot Standby 61 STBYSTAY Under Hot Standby 80 OFF XM being OFF XM operation mode 1 table Display example: If the system is receiving signals, the display will show [M1_2F_10]. 4.11 MICRO Status2 Display format : [ M 2 _ X X _ Y Y ] X : XM operation mode 2 (two effective digits of hexadecimal value). Y : XM operation mode 3 (two effective digits of hexadecimal value). _ : Spacing character. XM operation mode 2 table Mode number Mode name Meaning 00 STOP API control finished 01 START API control started 02 GETSID Getting SID 04 GETPROGNAME Switching program www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 45 5 6 7 8 5 6 7 8 C D F A B E 05 OFF Processing OFF 06 SETUP Application operation started 07 NEXTPROG Moves to the next program 08 SELPROG Selecting program 0A NEXTCAT Getting next category 0C GETCATNAME Getting next category name 0D NOSID No SID 0E GETID Getting HWID code 30 NEXTPROG1 Being in the first half of shift processing to the next channel 31 NEXTPROG2 Being in the latter half of shift processing to the next channel 32 SELPROG1 Selecting the program from NEXTPROG1 33 SELPROG2 Selecting the program from NEXTPROG2 34 RFCHK1 Waiting for restore from NOSIGNAL 35 RFCHK2 Waiting for restore from NOSIGNAL 36 SELPROGERR Processing select error during direct selection 37 NOWPROG Getting the current channel name XM operation mode 2 table Mode number Mode name Meaning 00 STOP XM circuit OFF completed 01 PWROFFW XM circuit power being OFF 02 STBYWT Resetting SSDEC 03 PWRON XM circuit initialization started 04 PWRONWT Waiting for XM circuit power ON being stabilized 05 STBY SSDEC reset started 06 PREMUTE Pre-DAC mute started 07 PREMUTEWT Waiting for pre-DAC mute 08 RF_INIT Downloading DSP patch code 09 DWLD Starts downloading DSP patch code 0A INIT SSDEC initialization started 0B INIT2 Initializing SSDEC (step 2) 0C INIT3 Initializing SSDEC (step 3) 0D INIT4 Initializing SSDEC (step 4) 0E INIT5 Initializing SSDEC (step 5) 0F INIT6 Initializing SSDEC (step 6) 10 INIT7 Initializing SSDEC (step 7) 11 INIT8 Initializing SSDEC (step 8) 12 INIT9 Initializing SSDEC (step 9) 13 INIT10 Initializing SSDEC (step 10: Issuing Power Up command) 14 SLEEPWT Waiting for reply from Power Off command 15 SLEEP Issues Power Off command 16 INIT10WT Initializing SSDEC (waiting for replay from Power Up command) 18 INIT11 Initializing SSDEC (step 11: Issuing Force Update command) 19 INIT11WT Waiting for reply from Force Update command 1A INIT12 Initializing SSDEC (step 12) 1F HOLD Waiting for other control being completed 20 IDLE Control completed 21 READY1 Preparation 1 before starting control 22 READY2 Preparation 2 before starting control 25 PURGECOM Preparation 3 before starting control (waiting for unnecessary command processing being completed) 26 PURGECOM1 Waiting for unnecessary OFF command processing being completed 27 RX_PREMUTE Starts pre-DAC mute in other than activation 28 RX_PREMUTE_WT Waiting for pre-DAC mute in other than activation 29 RX_AFTMUTE Starts post-DAC mute in other than activation 2A RX_AFTMUTE_WT Waiting for post-DAC mute in other than activation 2B SRVCANCEL Cancels selected service 2C SRVCANCEL_WT Waiting for completion of canceling selected service 2D SETENS Switches PLL ensemble 2E SETENSWT Waiting for switching of PLL ensemble 2F SETPCID Switching PCID of CDEC 30 SETENSWT2 Checking LDET after switching PLL ensemble www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 46 1 2 3 4 1 2 3 4 C D F A B E 31 CHECK_RQ Outputs Service/Channel Check command. Or outputs Channel UpDown/ Program UpDown command. 32 CHECK_RQ1 Issues Channel Check command in the channel searched by Channel UpDown or Program UpDown command 33 CHECK_WT Waiting for a reply from the command output by CHECK_RQ 34 CHECK_WT1 Waiting for a reply from the command output by CHECK_RQ1 35 SERVICE_EXT_RQ Issues Service Extract command 36 SYNC_SQST1 Waiting for synchronization before issuing Service Extract command (1) 37 SYNC_SQST2 Waiting for synchronization before issuing Service Extract command (2) 38 SYNC_SQST3 Waiting for synchronization before issuing Service Extract command (3) 39 SERVICE_EXT_WT Waiting for completion of Service Extract 3A SERVICE_EXT_RQ1 Issues Service Extract command at the time of retry 3B SERVICE_EXT_WT1 Waiting for completion of Service Extract at the time of retry 3D NXTCATNO Getting the next category number 3E GETBIC Getting labels 3F GETBICWT Waiting for acquisition of labels 40 EXT_CHK Starts Extract state check 41 EXTERR_WT Checking Extract state 42 BICADF_CHG_CHK Checks program information changes 43 ANT_CHK Checking antenna connection state 44 ACTIVATE_CHK Checking Activation state 45 UPDATE_CATLIST Starts updating category list 46 UPDATE_CATLISTWT Updating category list 47 SSDEC_CHK_BITRATE Checking bit rate 48 SSDEC_CHK_BITRATE _WT Waiting for completion of bit rate check 49 SSDEC_CHK_DECDER Checking decoding state 4A SSDEC_FLAME _COUNT Counting the number of errors 4B SSDEC_RECOVER _DECODER_WT Completing recovery processing 4C SSDEC_RECOVER _DECODER1 Processing Recovery 1 4D SSDEC_RECOVER _DECODER1_WT Waiting for completion of processing Recovery 1 4E SSDEC_RECOVER _DECODER2 Processing Recovery 2 4F SSDEC_RECOVER _DECODER2_WT Waiting for completion of processing Recovery 2 50 SSDEC_RECOVER _DECODER3 Processing Recovery 3 51 SSDEC_RECOVER _DECODER3_WT Waiting for completion of processing Recovery 3 52 SSDEC_RECOVER _DECODER4 Processing Recovery 4 53 SSDEC_RECOVER _DECODER4_WT Waiting for completion of processing Recovery 4 54 SSDEC_RECOVER _DECODER5 Processing Recovery 5 55 SSDEC_RECOVER _DECODER5_WT Waiting for completion of processing Recovery 5 56 SSDEC_RECOVER _DECODER6_WT Waiting for completion of processing Recovery 6 59 ACTIVATE_CHK1 Starts Activation Check 5A ACTIVATE_CHK1_WT Waiting for completion of Activation Check 5D API_SERVICE_EXT _WT3 Waiting for completion of high-speed Service Extract E0 HWERROR Activation stop due to CAP error E1 VERERROR Activation stop due to unknown version of DSP core software E2 ANTSHORT Antenna short-circuited E3 ANTOPEN Antenna not connected E4 NOSIGNAL All error rates of Viterbi decoding are 100%. E5 RF_UNLOCK PLL cannot be locked www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 47 5 6 7 8 5 6 7 8 C D F A B E E6 ERV_UNAVAIL Designated program is not found. E7 TYPE_UNAVAIL Program with designated service type is not found. E8 PROG_UNAVAIL Program with designated category is not found. E9 UNKNOWN_PC PC format is not standard. EA ACT_REQ Activation required EB AUTH_REQ Authorization required EC OFFAIR Service being off-air ED DIFF_ENS Designated Primary and Secondary PCID are not found on the same ensemble. EE PC_UNDETECT Unable to receive PC of selected program EF SID_UNDETECT Unable to identify SID of selected program F0 SCT_UNDETECT Unable to identify the service component type of selected program F1 AUTH_MISS Updating encryption key F3 RAT_BLOCK Being out of contract F4 RAT_LOW A program out of the contract was selected. F5 TOD_ROLLBACK The time information controlled in DSP core does not match the time information during on-air. F6 IDLE_WT Preparing for control completion F7 DIFF_PCID PCID discrepancy FF REQ_RETRY SSDEC error occurred (restart required) Display example: If the system is receiving, the display will momentarily show [M2_00_20]. 4.12 ANTENNA PASS No display. If an antenna is not connected, and if this setting is made while the system is displaying the "ANTENNA" message, connection checks will not be conducted until the system has been reset (the system will assume normal operation without an antenna check). 4.13 QOS Message Display format : [ 1 A A B B C C D ] A : The Viterbi error rate (two effective digits of decimal value) of ground wave. (*1) B : The Viterbi error rate (two effective digits of decimal value) of satellite wave 1. (*1) C : The Viterbi error rate (two effective digits of decimal value) of satellite wave 2. (*1) D : The quality of service (QOS) value (a single effective digit decimal value). (*2) *1 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will show "-". For 100, the display will show "XX". If a signal is not received, the display will show "NS." *2 : The single digit display may show from 0 to 9. If the display information is being acquired, the display will show "-". For 10 and over, the display will show "X". 4.14 TERR Message Display format : [ 2 A B B C C D D ] A : The locking status of the ground wave. (*1) B : The ground wave Viterbi signal error rate (two effective digits of decimal value). (*2) C : The ground wave Read-Solomon symbol error rate (two-effective digits of decimal value). (*3) D : The ground wave Read-Solomon non-correction code word (two effective digits of decimal value). (*4) *1 : The "-" will be displayed while the system is acquiring the information, "N" if the signal is not locked on, "D" if only the demodulator is locked, and "T" if both the TDM and demodulator are locked on. *2 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will show "-". For 100, the display will show "XX". If a signal is not received, the display will show "NS." *3 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will show "-". For 100, the display will show "XX". *4 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will show "-". For 100, the display will show "XX". www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 48 1 2 3 4 1 2 3 4 C D F A B E 4.15 STA1 Message Display format : [ 3 A B B C C D D ] A : The locking status of the satellite wave 1. (*1) B : The satellite wave 1 Bitabi signal error rate (two effective digits of decimal value). (*2) C : The satellite wave 1 Read-Solomon symbol error rate (two-effective digits of decimal value). (*3) D : The satellite wave 1 Read-Solomon non-correction code word (two effective digits of decimal value). (*4) *1 : The "-" will be displayed while the system is acquiring the information, "N" if the signal is not locked on, "D" if only the demodulator is locked, and "T" if both the TDM and demodulator are locked on. *2 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will show "-". For 100, the display will show "XX". If no signal is received, the display will show "NS." *3 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will show "-". For 100, the display will show "XX". *4 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will show "-". For 100, the display will show "XX". 4.16 SAT2 Message Display format : [ 4 A B B C C D D ] A : The locking status of the satellite wave 2. (*1) B : The satellite wave 2 Bitabi signal error rate (two effective digits of decimal value). (*2) C : The satellite wave 2 Read-Solomon symbol error rate (two-effective digits of decimal value). (*3) D : The satellite wave 2 Read-Solomon non-correction code word (two effective digits of decimal value). (*4) *1 : The "-" will be displayed while the system is acquiring the information, "N" if the signal is not locked on, "D" if only the demodulator is locked, and "T" if both the TDM and demodulator are locked on. *2 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will show "-". For 100, the display will show "XX". If no signal is received, the display will show "NS." *3 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will show "-". For 100, the display will show "XX". *4 : The two-digit display may show from 0 to 99. If the display information is being acquired, the display will show "-". For 100, the display will show "XX". 4.17 Tuner Message Display format : [ 5 A B _ _ _ _ _ ] A : The locking status of the PLL signal (L= locked, U = unlocked). B : Antenna connection status (D= normal, U = connection failure). 4.18 Blank 4.19 SSDEC Status1 Display format : [ 6 A A A B B C C ] A : The synchronization status of the PC signal (S10 = synchronized, U01 = asynchornous). B : Overflow count during voice service data input (two effective digits of hexadecimal value). C : Underflow count during the PCM output (two effective digits of hexadecimal value). 4.20 SSDEC Status2 Display format : [ 7 _ A A A A A A ] A : General error information of SSDEC (six effective digits of hexadecimal value). www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 49 5 6 7 8 5 6 7 8 C D F A B E 4.21 SSDEC Status3 Display format : [ 8 _ _ _ A A A A ] A : The Extract error information 1 of the SSDEC (four effective digits of hexadecimal value). 4.22 SSDEC Status4 Display format : [ 9 _ _ _ A A A A ] A : The Extract error information 2 of the SSDEC (four effective digits of hexadecimal value). 4.23 Blank 4.24 MICRO VERSION Display format : [ V E R A A A . B ] A : Main microcomputer major version (two effective digits of decimal value). B : Main microcomputer minor version (a single effective digit of decimal value). C : Sub microcomputer major version (two effective digits of decimal value). D : Sub microcomputer minor version (a single effective digit of decimal value). Display example : If the Main version is 14.7 and Sub version is 2.0, the display will show [ 1 4 . 7 0 2 . 0 ]. 4.25 SAT1 C/N Display format : [ 1 _ X X X . Y Y ] X : Integer part of C/N ratio (three effective digits of decimal value). Y : Fractional part of C/N ratio (00/25/50/75). Displays C/N ratio of satellite wave 1. The unit is dB. Display example : If the C/N ratio is 6.75 dB, the display will show [ 1 _ _ _ 6 . 7 5 ]. 4.26 SAT2 C/N Display format : [ 2 _ X X X . Y Y ] X : Integer part of C/N ratio (three effective digits of decimal value). Y : Fractional part of C/N ratio (00/25/50/75). Displays C/N ratio of satellite wave 2. The unit is dB. Display example : If the C/N ratio is 6.75 dB, the display will show [ 2 _ _ _ 6 . 7 5 ]. 4.27 ZIF AFC Check Display format : [ X X _ Y Y _ Z Z ] X : AFC identification of satellite wave 1 (OK/NG). Y : AFC identification of satellite wave 2 (OK/NG). Z : AFC identification of ground wave (OK/NG). Identifies as valid (OK) if AFC offset of satellite wave 1, 2, and ground wave, respectively, is below 2 KHz. Identifies as invalid (NG) if it is above 2 KHz. Display example : If the AFC offset of satellite wave 2 is invalid and that of others are valid, the display will show [ O K _ N G _ O K ]. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 50 1 2 3 4 1 2 3 4 C D F A B E 4.28 SAT RSERR Display format : [ S _ X X _ _ Y Y ] X : RS Error Block 1 of satellite wave (two effective digits of decimal value). Y : RS Error Block 2 of satellite wave (two effective digits of decimal value). Displays RS Error Block 1 or 2 of satellite wave. Display example : If the Sat Rs Err1 = 10 and Sat Rs Err2 = 8, the display will show [ S _ 1 0 _ _ _ 8 ]. 4.29 TERR RSERR Display format : [ T _ X X _ _ Y Y ] X : RS Error Block 1 of ground wave (two effective digits of decimal value). Y : RS Error Block 2 of ground wave (two effective digits of decimal value). Displays RS Error Block 1 or 2 of ground wave. Display example : If the Terr Rs Err1 = 8 and Terr Rs Err2 = 10, the display will show [ T _ _ 8 _ _ 1 0 ]. 4.30 Blank 4.31 SAT1 AFC Display format : [ 1 _ X . X X Y Z ] X : AFC offset frequency value of satellite wave 1 (1 integer digit and 2 fractional digits). The unit is Hz. Y : Positive/Negative sign of index (+/-). Z : Index (decimal). Displays AFC offset frequency value of satellite wave 1. The index is displayed with 2 fractional digits. Display example : If the AFC offset of satellite wave 1 is 12.3 Hz, the display will show [ 1 _ 1 . 2 3 + 1 ]. 4.32 SAT2 AFC Display format : [ 2 _ X . X X Y Z ] X : AFC offset frequency value of satellite wave 2 (1 integer digit and 2 fractional digits). The unit is Hz. Y : Positive/Negative sign of index (+/-) . Z : Index (decimal). Displays AFC offset frequency value of satellite wave 2. The index is displayed with 2 fractional digits. Display example : If the AFC offset of satellite wave 2 is 451Hz, the display will show [ 2 _ 4 . 5 1 + 2 ]. 4.33 TERR AFC Display format : [ T _ X . X X Y Z ] X : AFC offset frequency value of ground wave (1 integer digit and 2 fractional digits). The unit is Hz. Y : Positive/Negative sign of index (+/-). Z : Index (decimal). Displays AFC offset frequency value of ground wave. The index is displayed with 2 fractional digits. Display example : If the AFC offset of ground wave is 1023Hz, the display will show [ T _ 1 . 0 2 + 3 ]. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 51 5 6 7 8 5 6 7 8 C D F A B E 7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 DISASSEMBLY - Removing the Main Unit (Fig.2) 1 Fig.1 - Removing the Case (Fig.1) Fig.2 Remove the five screws and then remove the Case. 1 Case 1 1 1 1 Main Unit 3 2 2 3 2 3 2 Straighten the tabs at four locations indicated. 2 Remove the two screws. 3 Remove the three screws and then remove the Main Unit. 1 1 1 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 52 1 2 3 4 1 2 3 4 C D F A B E 7.1.2 CONNECTOR FUNCTION DESCRIPTION 1 2 3 1.GND 2.ACC 3.BATT. POWER SUPPLY 8 9 10 11 5 6 7 1 2 3 4 1.BUS+ 2.BUSG5 3.BUSG5 4.NC 5.BUS- 6.BUSG5 7.BUSL3 8.ASENB 9.BUSR3 10.BUSAG1 11.BUSAG1 IP-BUS OUT 8 9 10 11 5 6 7 1 2 3 4 1.BUS+ 2.BUSG1 3.BUSG1 4.NC 5.BUS- 6.BUSG1 7.BUSL1 8.ASENB 9.BUSR1 10.BUSR2 11.BUSL2 IP-BUS IN XM ANTENNA DATA OUT 1.NC 2.NC 3.GNDD 4.NC 5.NC 6.NC 7.CTOXM 8.XMTOC 9.NC 10.CSENS 1 2 9 10 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 53 5 6 7 8 5 6 7 8 C D F A B E 7.2 IC * K4S280832F-TC75 DQ0 2 VDDQ 3 NC 4 DQ1 5 VSSQ 6 NC 7 DQ2 8 VDDQ 9 NC 10 DQ3 11 VSSQ 12 NC 13 VDD 14 WE 15 CAS 16 RAS 17 CS 18 BA1 19 A10/AP 20 A0 21 A1 22 A2 23 A3 24 48 NC 47 VSSQ 46 DQ6 45 NC 44 VDDQ 43 DQ5 42 NC 41 VSSQ 40 DQ4 39 NC 38 37 VSS 36 DQM 35 CLK 34 CKE 33 NC 32 A9 31 A8 30 A7 29 A6 28 A5 54 A4 53 VSS VDD 1 VDD 25 49 DQ7 50 VSS 26 27 52 51 NC BA0 A11 NC VDDQ A0-A11 : Address input BA0-BA1 : Bank select address DQ0-DQ7 : Data input/output CLK : Clock input CKE : Clock enable cs : Chip select ras : Row address strobe cas : Column address strobe we : Write enable DQM : Data input/output mask VDD : Power supply VSS : GND VDDQ : Data output power supply VSSQ : Data output GND NC : Not used GND VO VB IC 5 2 3 VC 4 VIN 1 PQ012FZ01ZP - + Vref 1 2 3 VCC NC OUT Driver OCP TSD BA033CC0FP GND(FIN) OVP IC's marked by * are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 54 1 2 3 4 1 2 3 4 C D F A B E - Pin Functions(STA850P) Pin No. Pin Name I/O Function and Operation 1 CLKO O 23.92MHz Clock output 2 I2C_ADDR I I2C device address select input 3 GND9 Digital GND 4 MCLK I Master clock input 5 TCS Reserved for Test 6 GNDIO1 Pad ring GND 7 VDDIO1 3.3V Pad ring power supply 8 TEST_EN I Test enable input 9 FTESTEN I Functional test enable input 10 INCM1 I ADC1 C. M. reference input 11 REFP1 I ADC1 reference input (+) 12 REFM1 I ADC1 reference input (-) 13 AD_GND_1 ADC GND 14 INM1 I ADC1 differential input (-) 15 INP1 I ADC1 differential input (+) 16 AD_GND_2 ADC GND 17 INP2 I ADC2 differential input (+) 18 INM2 I ADC2 differential input (-) 19 AD_GND_3 ADC GND 20 REFM2 I ADC2 reference input (-) 21 REFP2 I ADC2 reference input (+) 22 AD_VDD3_1 ADC 3.3V Analog power supply 23 INCM2 I ADC2 C. M. reference input 24 AD_VDD3_2 ADC 3.3V Analog power supply 25 AD_GND_4 ADC Analog GND 26 AD_VDD3_3 ADC 3.3V Analog power supply 27 AD_GND_5 ADC Analog GND 28 AD_VDD3_4 ADC 3.3V Analog power supply 29 AD_GND_6 ADC Analog GND 30 AD_VDD3_5 ADC 3.3V Analog power supply 31 AD_GND_7 ADC Analog GND 32 AD_VDD_1 ADC 1.2V Digital power supply 33 CRESET I CDEC master reset input 34 SRESET I SDEC master reset input 35 VDD1 1.2V Positive power supply 36 GND1 Digital GND 37 AGC1 O ADC1 AGC control signal output 38 AGC2 O ADC2 AGC control signal output 39 SCLKI I/O SDEC Clock input/output 40 CLK_SC O System microcomputer clock output 41 VDD2 1.2V Positive power supply 42 GND2 Digital GND 43-52 XADC0-9 I/O External ADC input (Bit0-9) 53 VDDIO2 3.3V Pad ring power supply 54 GNDIO2 Pad ring GND 55,56 XADC10,11 I/O External ADC input (Bit10,11) 57 LOCK_M O Terr. Dem lock indicator output 58 LOCK_S1 O Sat. Dem1 lock indicator output 59 LOCK_S2 O Sat. Dem2 lock indicator output 60 VDD3 1.2V Positive power supply 61 GND3 Digital GND 62 RS232CTLIN I RS232C control input 63 RS232CTLOUT O RS232C control output 64 SDA I/O I2C-bus serial data input/output 65 SCL I I2C-bus serial clock input 66 CDEC_INTR O CDEC Interrupt output 67 SDEC_INTR O SDEC Interrupt output (GPIO_0) 68 SCLKO O SDEC Master clock output 69 RS232TX O CDEC-SDEC RS232C transmitter output 70 RS232RX I SDEC RS232C receive input 71 APLL_GND Audio PLL GND 72 APLL_VDD Audio PLL 1.2V power supply www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 55 5 6 7 8 5 6 7 8 C D F A B E Pin No. Pin Name I/O Function and Operation 73 SFILT O SDEC Audio PLL filter output 74 GND4 Digital GND 75 VDD4 1.2V Positive power supply 76 FIT I RFU input (FIT_0) 77 SAll_DATA_REG O External audio output data request (GPIO_5) 78 SAll_SCLK I External audio input clock (SCLK_USSIO1) 79 SAll_DATA I External audio input data (DATA_USSIO1) 80 SCAN_EN I Scan test enable input 81 OCLK O Oversampling clock output 82 LRCKT O I2S left/right clock output 83 SCKT O I2S serial clock output 84 SDO O I2S output data (PCM data) 85 GPIO2 I/O RFU input/output (GPIO_2) 86 GND5 Digital GND 87 VDD5 1.2V Positive power supply 88 I958_OUT O S/PDIF IEC958 output 89 GPIO1 I/O RFU input/output (GPIO_1) 90 DP_EN I/O Data port frame sync input/output (USSIO3) 91 DP_CLK I/O Data port clock input/output (SCLK_USSIO3) 92 DP_DATA I/O Data port data input/output (DATA_USSIO3) 93 CAP_RST I/O CAP reset input/output 94 GNDIO3 Pad ring GND 95 VDDIO3 3.3V Pad ring power supply 96 CAP_SCL_M O CAP I2C master serial clock output 97 CAP_SDA_M I/O CAP I2C master serial data input/output 98 PCFS0 I/O PC PRC Frame sync #0 input/output 99 PCDC0 I/O PC data clock #0 input/output 100 PCSD0 I/O PC serial data #0 input/output 101 PCFS1 I/O PC PRC Frame sync #1 input/output 102 PCDC1 I/O PC data clock #1 input/output 103 PCSD1 I/O PC serial data #1 input/output 104 GND6 Digital GND 105 VDD6 1.2V Positive power supply 106 PCBS_SYNC I/O Slave synchronization input/output 107 MFP_CLK I/O TDM master frame clock input/output 108 SM I/O Slave/master PRC control input/output 109-113 MADD11-7 I/O External memory address input/output (Bit11-7) 114 GND7 Digital GND 115 VDD7 1.2V Positive power supply 116-122 MADD6-0 I/O External memory address input/output (Bit6-0) 123,124 MBS1,0 O External memory block select output (Bit1,0) 125 GNDIO4 Pad ring GND 126 VDDIO4 3.3V Pad ring power supply 127,128 MCS1,0 O External memory chip select output (Bit1,0) 129 RAS O External memory row address strobe output 130 CAS O External memory col. address strobe output 131 MWE O External memory write enable output 132-135 MDQ7-4 I/O External memory data input/output (Bit7-4) 136 GND8 Digital GND 137 VDD8 1.2V Positive power supply 138-141 MDQ3-0 I/O External memory data input/output (Bit3-0) 142 MDQM O External memory data mask output 143 CLKON O 23.92MHz inv. clock output 144 MCKE O External memory clock enable output www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 56 1 2 3 4 1 2 3 4 C D F A B E 36 37 72 73 108 109 144 1 * STA850P ON/OFF Circuit Reference voltage circuit Overcurrent protection circuit + VIN VOUT 5 4 3 NC 2 VSS ON/OFF 1 * S-T111B33MC-0GS VOUT GND VIN Thermal Protection Bandgap Reference Noise Bypass Cont 1 2 3 4 5 2 CONTROL GND NOISE BYPASS VOUT VIN GND NJM2880U1-05 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 57 5 6 7 8 5 6 7 8 C D F A B E - Pin Functions(PEG100A) Pin No. Pin Name I/O Function and Operation 1-5 NC Not used 6 BYTE I External bus width select input 7 CNVSS I Processor mode select input 8,9 NC Not used 10 reset I Reset input 11 XOUT Crystal oscillator connection pin 12 VSS GND 13 XIN Crystal oscillator connection pin 14 VCC Power supply (3.3V) 15 NMI Not used 16 NC Not used 17 STBY I Stand-by sense input 18 DATAINT I LSDP receive interrupt input 19-26 NC Not used 27 NAVIRX I Navigation system I/F input 28 NAVITX O Navigation system I/F output 29 NC Not used 30 LSDPRX I LSDP signal input 31,32 NC Not used 33 MAINTX O Main microcomputer I/F output 34 MAINRX I Main microcomputer I/F input 35-38 NC Not used 39 EPM Not used 40 NC Not used 41 TESTIN I Test program sense input 42-59 NC Not used 60 VDD Power supply (3.3V) 61 NC Not used 62 VSS GND 63-69 NC Not used 70 FLASHIN Not used 71-75 NC Not used 76 RDT I/O EEPROM data input/output 77 RCK O EEPROM clock output 78 RCS O EEPROM chip enable output 79-93 NC Not used 94 AVSS Analog GND 95 NC Not used 96 VREF Analog reference voltage 97 AVCC Analog power supply 98-100 NC Not used * PEG100A 25 26 50 51 75 76 100 1 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 58 1 2 3 4 1 2 3 4 C D F A B E - Pin Functions(PEG099A) Pin No. Pin Name I/O Function and Operation 1-5 NC Not used 6 BYTE I External bus width select input 7 CNVSS I Processor mode select input 8,9 NC Not used 10 reset I Reset input 11 XOUT Crystal oscillator connection pin 12 VSS GND 13 XIN Crystal oscillator connection pin 14 VCC Power supply (3.3V) 15 NMI Not used 16,17 NC Not used 18 INTR I CDEC frame interrupt input 19 IPTA4IN I IP-BUS connect input 20 IPPW O IP-BUS driver power supply control output 21-26 NC Not used 27 IPIN I IP-BUS data input 28 IPOUT O IP-BUS data output 29 IPFLASHTX Not used 30 IPFLASHRX Not used 31,32 NC Not used 33 SUBTX O Sub microcomputer communication output 34 SUBRX I Sub microcomputer communication input 35 NC Not used 36 substby O Sub microcomputer stand-by control output 37 ACCPW2 O Microcomputer active state output 38 ACCPW O Not used 39 EPM Not used 40 NAVSW I Connection of the navigation system detect input 41 TESTIN I Test program sense input 42 MUTE O Mute output 43 ANSW O Source select output 44 CE Not used 45-48 NC Not used 49 SYSPW O Audio circuit power supply output 50-56 NC Not used 57 DAC_EN O DAC IC latch enable output 58 NC Not used 59 RESET_N O SSDEC reset output 60 VDD Power supply (3.3V) 61 NC Not used 62 VSS GND 63,64 NC Not used 65 MRESET O CDEC reset output 66-69 NC Not used 70 FLASHIN Not used 71 asens I ACC sense input 72 asenb I ACC (IP-BUS) sense input 73 bsens I Backup sense input 74,75 NC Not used 76 RDT I/O EEPROM data input/output 77 RCK Not used 78 RCS Not used 79-81 NC Not used 82 XMPW O XM tuner power supply control output 83-92 NC Not used 93 SDA I/O RF/HCMOS9 communication data input/output 94 AVSS Analog GND 95 SCL O RF/HCMOS9 communication clock output 96 VREF Analog reference voltage 97 AVCC Analog power supply www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 59 5 6 7 8 5 6 7 8 C D F A B E Pin No. Pin Name I/O Function and Operation 98 NC Not used 99 DACDT O DAC IC data output 100 DACCL O DAC IC clock output * PEG099A 25 26 50 51 75 76 100 1 GND IN- IN+ VCC Q 2 1 3 4 5 IN- : Comparator A Inverting Input IN+ : Comparator A Noninverting Input Q : Comparator A TTL Output VCC : Positive Supply Input GND : Ground * MAX999EUK 1 2 4 3 5 6 7 IF2QO- SCL IF2QI- IF2QO+ RFAGC_C VCC_FE0 RFIN- XM TUNER I2CA1 I2CA2 SDA IFOUT- IFOUT+ VCC_FE1 RFIN+ CHP 1/N 1/R /4/8 QUAD PFD 17 IF2II- IF2IO+ IF2IO- IF2II+ VINANT VOUTANT 16 VCC_BE1 13 14 15 8 9 10 11 21 VCC_BE2 IOUT- IOUT+ 20 19 22 12 18 33 32 30 31 29 28 27 26 25 24 23 35 36 37 34 38 39 40 41 42 43 44 VCC_FE2 IFIN- IFIN+ IF2QI+ VCC_FE3 QOUT- QOUT+ VCC_D VCC_BE4 VCC_A LOCK CPOUT VCCREG REFOUT VCC_XTAL XTAL VTUNE VCC_BE3 AGCPWM LPF HPF LPF HPF RF AGC VCC_VCO - MOD MAX2140ETH ∑ www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 60 1 2 3 4 1 2 3 4 C D F A B E 7.3 OPERATIONAL FLOW CHART VCC=3V Pin 14 Power ON RESET=H BSENS=L RESET Pin 10 BSENS Pin 73 ACCPW2←H Pin 37 IPPW←H Pin 22 POWER key valid SYSPW←H Pin 49 Starts communication with IP-BUS. POWER ON 150ms 225ms In case of the above signal, the communication with IP-BUS may fail. ASENS=L ASENS Pin 71 Completes power-on operation. XMPW←H Pin 82 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 61 5 6 7 8 5 6 7 8 C D F A B E 8. OPERATIONS Head unit (e.g. DEH-P6700MP) 1 CLOCK button Press and hold to change channel select mode. 2 DISPLAY button Press to select different displays. 3 FUNCTION button Press to select functions. 4 5 / ∞ / 2 / 3 buttons Press to select a channel, recall a channel and select a category. Also used for controlling functions. 5 BAND button Press to select among three XM bands and cancel the control mode of functions. 6 1–6 buttons Press for preset tuning. 7 SOURCE button Head unit is turned on by selecting a source. Press to cycle through all of the available sources. Remote control (e.g. DEH-P6700MP) You can operate in the same way with the remote control supplied with the head unit. 8 TUNER button Press to select the tuner as the source. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 62 1 2 3 4 1 2 3 4 C D F A B E Before You Start Resetting the microprocessor The microprocessor must be reset under the following conditions: • Prior to using this unit for the first time after installation • If the unit fails to operate properly • When strange or incorrect messages appear on the display • When changing the navigation system or unit combination • Press RESET on the unit with a pen tip or other pointed instrument. Power supply for this unit The method for turning this unit's power supply ON/OFF differs according to other units you combine with it. When combining this unit with either AVIC-D1, AVIC-N1, or AVIC-N2: • This unit's power supply can be turned OFF only if the ignition switch is turned OFF.If for any reason you want to switch the power of the unit OFF, switch the vehicle's ignition off (turn the ACC of your vehicle to OFF). When combining with another head unit (or AV head unit): • When the head unit's power supply is OFF, this unit is also OFF. (Selecting a source other than XM tuner will not turn this product off.) • This unit's power supply can be turned OFF if the ignition switch is turned OFF. If for any reason you want to switch the power of the unit OFF, switch the vehicle's ignition off (turn the ACC of your vehicle to OFF). Selecting the XM source 1. Press SOURCE to turn the head unit on. 2. Press SOURCE to select "XM" source. Press SOURCE repeatedly to switch between the following sources: XM tuner – Tuner – Television – DVD player/Multi- DVD player – Built-in CD player – Multi-CD player – External unit 1 – External unit 2 – AUX To quit listening to the XM tuner, press SOURCE to switch to another source or press SOURCE and hold until the head unit turns off. XM tuner Note www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 63 5 6 7 8 5 6 7 8 C D F A B E Listening to XM These are the basic steps necessary to operate the XM. 1 XM channel select setting indicator Shows what channel select setting has been selected. CH.No is displayed when CH NUMBER is selected, and CAT is displayed when CATEGORY is selected. 2 XM channel number indicator Shows to which XM channel number the tuner is tuned to. 3 XM band indicator Shows the XM band which has been selected. 4 XM preset number indicator Shows what XM preset has been selected. 5 XM channel name Shows the channel name of broadcast channel. XM tuner 1. Press SOURCE to select a XM source. 2. Press BAND to select a band. Press BAND until the desired band is displayed, XM1, XM2 or XM3. 3. Press 2 or 3 to select the desired channel. The channel number moves up or down successively. Channels that cannot currently be selected are skipped, and the next channel is selected. • If you press and hold 2 or 3, you can increase or decrease channel number continuously. • You can also select a channel from a desired channel category. (Refer to "Switching the channel select mode".) 4. Press SOURCE and hold until the head unit turns off or press SOURCE to select another source. • When you turn the power on, change the source to XM tuner, or select a channel, it may take a few seconds while this unit acquires and processes the satellite signal before you can hear anything. • Depending on the head unit, it may be possible to switch to channel number direct input mode using the allocated button on the remote control (e.g. DIRECT). Note XM tuner Note Storing and recalling channels If you press any of the preset tuning buttons 1–6 you can easily store up to six channels for later recall with the touch of a button. • Memory and recall are for broadcasts. If you recall a memorized broadcast that has been moved to another channel, the channel to which the broadcast was moved is selected. • When you find a channel that you want to store in memory, press one of the preset tuning buttons 1–6 and hold until the preset number stops flashing. The number you have pressed will flash in the preset number indicator and then remain lit. The selected channel has been stored in memory. The next time you press the same preset tuning button, the channel is recalled from memory. • Up to 18 channels, six for each of the three XM bands, can be stored in memory. • When channel number select mode is selected, you can also use 5 and ∞ to recall channels assigned to preset tuning buttons 1–6. • If a channel you have recalled cannot be selected, a message is displayed for 2 seconds and the unit returns to the operating status before the channel was recalled. Switching the XM display XM channels each have a channel number and channel name. XM programing also carries the song or program title, the artist name and category when available. • Press DISPLAY. Press DISPLAY repeatedly to switch between the following settings: Channel name – Artist name/feature – Song/program title – Channel category www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 64 1 2 3 4 1 2 3 4 C D F A B E XM tuner Introduction of advanced tuner operation 1 Function display Shows the function status. • Press FUNCTION to display the function name. Press FUNCTION to display the following function: MODE (Channel select mode) • To return to the XM display, press BAND. Switching the channel select mode When selecting a channel, you can switch between selecting a channel by channel number or by channel category. Initially, channel number select mode isselected. 1. Press FUNCTION to select MODE. Press FUNCTION until MODE appears in the display. 2. Press 2 or 3 to select the desired channel select mode. Press 2 or 3 repeatedly to switch between the following settings: CH NUMBER (Channel number select mode)– CATEGORY (Channel category select mode) Depending on the head unit you are using, it may be possible to directly switch between the channel select mode using the allocated button (e.g. CLOCK). Note XM tuner Selecting the channel in the channel category Channels are organized into various program categories, e.g. Rock, Classic, Jazz. You can search between different categories, and then search among channels within each channel category. 1. Select the channel category select mode. (Refer to "Switching the channel select mode" above.) 2. Press BAND to return to the previous display. 3. Press 5 or ∞ to select the desired channel category. Once you select a channel category, the unit searches for channels in that category. During search, the channel category doesn't immediately change even if you press the button. To successively change the channel category, continue pressing the button. 4. Press 2 or 3 to select the desired channel in the selected channel category. The channel number moves up or down in the selected channel category. Channels that cannot currently be selected are skipped, and the next channel in that channel category is selected. If you select a channel of another category by channel recall, etc., during steps 3 and 4, the category selected in step 3 still remains in memory. If you press 2 or 3, the channel number moves up or down in the category selected in step 3 regardless of the category of the present channel. Display the ID code (Radio ID) Each XM tuner is identified with a unique Radio ID. You will need the Radio ID when activating XM service or when reporting a problem. How to display the ID code depends on the channel select mode. Carefully check your XM Radio ID. The letters F, I, O, and S are not used. Channel number select mode If you select CH 000, the ID code is displayed. • Press 2 or 3 to select the channel number zero (CH 000). Channel category select mode RADIO ID is provided as a channel category for displaying the ID code. • Press 5 or ∞ to select the RADIO ID from channel category. • If you select another channel, display of the ID code is canceled. • Display of the ID code repeats displaying RADIO ID and the ID code one after the other. Note Note Note www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 65 5 6 7 8 5 6 7 8 C D F A B E This product Antenna Input Power Supply Antenna Unit Violet Yellow To terminal always supplied with power regardless of ignition switch position. Black (ground) To vehicle (metal) body. Fuse holder (2 A) Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF. 5m (16 ft. 5 in.) Fuse resistor This product Head Unit (sold separately) IP-BUS cable (supplied) To IP-BUS input (blue) IP-BUS output (black) IP-BUS input (blue) Multi-CD player (sold separately) IP-BUS cable Not used. Black Blue 3 m (9 ft. 10 in.) - CONNECTION DIAGRAM Connecting the power cord and antenna Connecting the system (1) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com GEX-P10XMT/XN/UC 66 1 2 3 4 1 2 3 4 C D F A B E Navigation system (sold separately) (e.g. AVIC-D1, AVIC-N2, AVIC-N1) Note: When combining this product with AVIC-N1 (sold separately), be sure to updated with the latest map disc CNDV-50MT [CNDV-50MTP] (sold separately) to utilize traffic and data functionality. Note: When combining this product with Pioneer navigation system (sold separately), this connection is required. IP-BUS Input DATA OUT port This product IP-BUS cable (supplied) To IP-BUS Input (Blue) Multi-CD player (sold separately) IP-BUS cable Black Blue 3 m (9 ft. 10 in.) Hide-away unit EXTENSION port Display unit Blue To EXTENSION port 3 m (9 ft. 10 in.) Black Black XM DATA cable Connecting the system (2) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com