ORDER NO. PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2004 DVR-RT500-S RRV3033 DVD RECORDER DVR-RT500-S DVR-RT300-S THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). Model Type Power Requirement Region No. Remarks DVR-RT500-S UXTLCA AC120V 1 DVR-RT300-S UXTLCA AC120V 1 For details, refer to "Important Check Points for good servicing" . T-ZZV SEPT. 2004 printed in Japan www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 2 1 2 3 4 1 2 3 4 C D F A B E SAFETY INFORMATION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 – Proposition 65 NOTICE Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts must be of identical designation. REMARQUE Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pièces de remplacement doivent avoir la même désignation. ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURN- ING THE APPLIANCE TO THE CUSTOMER. 2. PRODUCT SAFETY NOTICE Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified by marking with a on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual may be obtained at a nominal charge from PIONEER. (FOR USA MODEL ONLY) 1. SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester such as Simpson Model 229-2 or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60 Hz outlet and turn the AC power switch on. Any current measured must not exceed 0.5 mA. Device under test Leakage current tester Earth ground Reading should not be above 0.5 mA Also test with plug reversed (Using AC adapter plug as required) Test all exposed metal surfaces AC Leakage Test www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 3 5 6 7 8 5 6 7 8 C D F A B E WARNING! DEVICE INCLUDES LASER DIODE WHICH EMITS INVISIBLE INFRARED RADIATION WHICH IS DANGEROUS TO EYES. THERE IS A WARNING SIGN ACCORDING TO PICTURE 1 INSIDE THE DEVICE CLOSE TO THE LASER DIODE. LASER DIODE CHARACTERISTICS MAXIMUM OUTPUT POWER : 50 mW WAVELENGTH : 654 - 662 nm LASER DIODE CHARACTERISTICS MAXIMUM OUTPUT POWER : 100 mW WAVELENGTH : 780 - 787 nm IMPORTANT THIS PIONEER APPARATUS CONTAINS LASER OF CLASS 1. SERVICING OPERATION OF THE APPARATUS SHOULD BE DONE BY A SPECIALLY INSTRUCTED PERSON. LABEL CHECK CLAMP signals for detecting the loading state are detected by the drive CPUs, and the design prevents laser diode oscillation when the CLAMP signal turns OFF. In normal operation, if no disc is clamped, the laser diode oscillation is disabled. However, the interlock does not always operate in the test mode. 2. When the cover is opened, close viewing of the objective lens with the naked eye will cause exposure to a Class 3A laser beam. Additional Laser Caution 1. The ON/OFF(ON:low level,OFF:high level) status of the DRW2194 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 4 1 2 3 4 1 2 3 4 C D F A B E [Important Check Points for Good Servicing] In this manual, procedures that must be performed during repairs are marked with the below symbol. Please be sure to confirm and follow these procedures. 1. Product safety Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual. 1 Use specified parts for repair. Use genuine parts. Be sure to use important parts for safety. 2 Do not perform modifications without proper instructions. Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise. 3 Make sure the soldering of repaired locations is properly performed. When you solder while repairing, please be sure that there are no cold solder and other debris. Soldering should be finished with the proper quantity. (Refer to the example) 4 Make sure the screws are tightly fastened. Please be sure that all screws are fastened, and that there are no loose screws. 5 Make sure each connectors are correctly inserted. Please be sure that all connectors are inserted, and that there are no imperfect insertion. 6 Make sure the wiring cables are set to their original state. Please replace the wiring and cables to the original state after repairs. In addition, be sure that there are no pinched wires, etc. 7 Make sure screws and soldering scraps do not remain inside the product. Please check that neither solder debris nor screws remain inside the product. 8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord. Damaged power cords may lead to fire accidents, so please be sure that there are no damages. If you find a damaged power cord, please exchange it with a suitable one. 9 There should be no spark traces or similar marks on the power plug. When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary. 0 Safe environment should be secured during servicing. When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely. 2. Adjustments To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification. Adjustments should be performed in accordance with the procedures/instructions described in this manual. 4. Cleaning For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances. 3. Lubricants, Glues, and Replacement parts Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied. 5. Shipping mode and Shipping screws To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 5 5 6 7 8 5 6 7 8 C D F A B E CONTENTS SAFETY INFORMATION......................................................................................................................................2 1. SPECIFICATIONS.............................................................................................................................................7 2. EXPLODED VIEWS AND PARTS LIST...........................................................................................................10 2.1 PACKING ..................................................................................................................................................10 2.2 EXTERIOR SECTION ..............................................................................................................................12 2.3 DECK ASSY (TOP SECTION) .................................................................................................................14 2.4 DECK ASSY (BOTTOM SECTION)..........................................................................................................16 2.5 WIRING CABLE........................................................................................................................................18 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................20 3.1 BLOCK DIAGRAM....................................................................................................................................20 3.1.1 OVERALL BLOCK DIAGRAM ...............................................................................................................20 3.1.2 MPEG BLOCK BLOCK DIAGRAM ........................................................................................................21 3.1.3 Y/C AUDIO / CCD / HEAD AMP BLOCK DIAGRAM .............................................................................22 3.1.4 SYSTEM CONTROL BLOCK DIAGRAM...............................................................................................23 3.1.5 REGULATOR BLOCK DIAGRAM..........................................................................................................24 3.1.6 OPERATION / DISPLAY BLOCK DIAGRAM .........................................................................................25 3.1.7 HiFi / DEMODULATOR BLOCK DIAGRAM...........................................................................................26 3.1.8 TUNER / JACK BLOCK DIAGRAM........................................................................................................27 3.1.9 AV SW BLOCK DIAGRAM ....................................................................................................................28 3.1.10 POWER BLOCK DIAGRAM ................................................................................................................29 3.2 OVERALL WIRING DIAGRAM .................................................................................................................30 3.3 DVD/HD MPEG PCB ASSY(1/6) ..............................................................................................................32 3.4 DVD/HD MPEG PCB ASSY(2/6) ..............................................................................................................34 3.5 DVD/HD MPEG PCB ASSY(3/6) ..............................................................................................................36 3.6 DVD/HD MPEG PCB ASSY(4/6) ..............................................................................................................38 3.7 DVD/HD MPEG PCB ASSY(5/6) ..............................................................................................................40 3.8 DVD/HD MPEG PCB ASSY(6/6) ..............................................................................................................42 3.9 VCR MT PCB ASSY(1/7)..........................................................................................................................44 3.10 VCR MT PCB ASSY(2/7)........................................................................................................................46 3.11 VCR MT PCB ASSY(3/7)........................................................................................................................48 3.12 VCR MT PCB ASSY(4/7)........................................................................................................................50 3.13 VCR MT PCB ASSY(5/7)........................................................................................................................52 3.14 VCR MT PCB ASSY(6/7)........................................................................................................................54 3.15 VCR MT PCB ASSY(7/7)........................................................................................................................56 3.16 POWER PCB ASSY ...............................................................................................................................58 3.17 OPEARTION PCB ASSY........................................................................................................................60 3.18 WAVE FORMS........................................................................................................................................61 4. PCB CONNECTION DIAGRAM ......................................................................................................................66 4.1 DVD/HD MPEG PCB ASSY......................................................................................................................66 4.2 VCR MT PCB ASSY .................................................................................................................................70 4.3 POWER PCB ASSY .................................................................................................................................74 4.4 OPERATION PCB ASSY..........................................................................................................................75 5. PCB PARTS LIST............................................................................................................................................76 6. ADJUSTMENT ................................................................................................................................................79 6.1 SERVICING FIXTURES AND TOOLS......................................................................................................79 6.2 ADJUSTMENT ITEMS AND NECESSARY ADJUSTMENT POINTS ......................................................80 6.3 SERVICE MODE LIST..............................................................................................................................82 6.4 CONFIRMATION OF HOURS USED .......................................................................................................83 6.5 PREVENTIVE CHECKS AND SERVICE INTERVALS .............................................................................84 6.6 MECHANICAL ADJUSTMENTS...............................................................................................................85 6.7 ELECTRICAL ADJUSTMENTS................................................................................................................89 6.8 WHEN REPLACING NEW DVD LOADER................................................................................................91 6.9 WHEN REPLACING EEPROM (MEMORY) IC.........................................................................................92 7. GENERAL INFORMATION .............................................................................................................................93 7.1 RE-WRITE FOR DVD FIRMWARE...........................................................................................................93 7.2 MEASUREMENT OF ERROR RATE........................................................................................................94 7.3 POWER ON SEQUENCE.........................................................................................................................95 7.4 DISC REMOVAL METHOD ......................................................................................................................96 7.5 TAPE REMOVAL METHOD AT NO POWER SUPPLY .............................................................................96 7.6 PARENTAL CONTROL-RATING LEVEL...................................................................................................97 7.7 TRAY LOCK..............................................................................................................................................97 7.8 DISASSEMBLY.........................................................................................................................................98 7.9 CAUTIONS ON DIASSEMBLING AND ASSEMBLING..........................................................................106 7.10 KEY TO ABBREVIATIONS ...................................................................................................................108 7.11 DISC/CONTENT FORMAT...................................................................................................................109 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 6 1 2 3 4 1 2 3 4 C D F A B E 7.12 CLEANING........................................................................................................................................... 111 8. PANEL FACILITIES ...................................................................................................................................... 112 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 7 5 6 7 8 5 6 7 8 C D F A B E 1. SPECIFICATIONS G-1 Outline of the product DVD-R/-RW Video Recorder & VHS Player/Recorder G-2 DVD System Color System NTSC Disc Format Rec DVD-R/-RW Play DVD-R/-RW, DVD-Video, CD-DA, CD-R/-RW Disc Diameter 120 mm, 80 mm Deck Disc Loading System Motor Front Disc Loading 3 Motors Pick up 1-Lens 2-Beams System Rec Time (Approx.) at 4.7 GB Disc XP SP LP SLP 1 hour at 10 Mbps 2 hour at 5 Mbps 4 hour at 2.5 Mbps 6 hour at 1.6 Mbps Playback time (Max) DVD 1-Layer DVD 2-Layer CD VIDEO CD 135 min (4.7 GB) 245 min (8.5 GB) 74 min – – Search speed Actual Fwd 4 step 2-45 times (DVD) 4-40 times (CD) Actual Rev 4 step 2-45 times (DVD) 4-40 times (CD) Slow speed Actual Fwd 1/8-1/2 times – – Actual Rev – – – – G-3 VCR System System VHS Player / Recorder Video System NTSC Hi-Fi STEREO Yes No NTSC PB (PAL 60Hz) Deck DECK Loading System Motor OVD-7 Front 3 Heads Video Head 4 Head FM Audio Head 2 Head Audio / Control Mono / Yes Erase (Full Track Erase) Yes Tape Speed Rec PAL NTSC – SP/SLP Play PAL NTSC – SP/LP/SLP Fast Forward / Rewind Time (Approx.) at 25°C with Cassette FF : 1'48" / REW : 1'48" T-120 Forward / Reverse Picture Search NTSC or PAL-M PAL or SECAM SP/LP/SLP = 3x, 5x / 7x, 9x / 9x, 15x – Frame Advance Yes Slow Speed 1/10 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 82 1 2 3 4 1 2 3 4 C D F A B E 6.3 SERVICE MODE LIST To enter one of the Sub-Service modes, hold a designated key on the unit pressed for a specified period of time while holding another designated key on the unit or on the remote control unit pressed. The following Sub-Service modes can be entered by first holding the designated key on the remote control unit pressed then pressing another designated key on the unit. For switching the RF output channels (CH 3/4) While the unit is off, hold the 3 or 4 key on the remote control unit pressed for at least 3 seconds. Mode of the Unit Key on the Unit Key on the Unit Specified Period (sec) Description VCR FF CH+ 2 For (1) initial setting of the µ-CON on the VCR side, (2) confirmation of initial settings for the Memory IC, and (3) displaying the accumulated time of playback and recording on the screen. VCR PLAY CH+ 2 Initialization to the state at shipment Note: Do NOT use this mode during normal servicing. This mode will reset the time setting, channel setting, and the accumulated time of playback/recording. VCR (Playback) CH+ CH– 2 For setting tracking to the center value Note: You can enter this mode by holding the ATR key on the remote control unit pressed for 2 seconds. VCR (Playback) REC/OTR DVD/VCR 2 For automatic adjustment of the PG shifter VCR CH+ REC/OTR 2 For entering Service mode Entering this mode disables the EOT/BOT/reel sensor and enables the VCR section of the unit to operate even if a tape is not loaded. VCR STOP CH+ 2 For entering DVD-Audio-Level/Separation Adjustment mode DVD CH– DVD/VCR 2 For displaying information VCR CH– S-BY/ON 2 For entering Operation-of-Only-VCR-Section mode Note: In this mode, you cannot switch to DVD mode even if connection of the DVD section has been made. Mode of the Unit Key on the Remote Control Unit Key on the Unit Specified Period (sec) Description DVD (NO DISC) 2 STOP 2 DVD 0 STOP 2 F/W Writing mode DVD 6 STOP 2 For initial setting of µ-CON on the DVD side For setting and unlocking the TRAY Lock. This mode functions cyclically. DVD (NO DISC) 7 STOP 2 For canceling Parental Lock Note: This mode functions only when a disc is not loaded in DVD mode DVD (NO DISC) 8 STOP 2 For entering Region-Code Writing mode DVD (Playback, NO DISC) 9 STOP 2 For displaying Loader Information and error rates www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 9 5 6 7 8 5 6 7 8 C D F A B E Accessories • Transmitter ×1 (076R0JZ010) • RF antenna cable ×1 (06CPL02006) • RCA Pin cable(L=1.2m) ×1 (red/white/yellow) (06CPBA2003) • Dry cell batteries ×2 (AAA/R03) • Warranty Card • Operating Instructions Red White Yellow www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 10 1 2 3 4 1 2 3 4 C D F A B E 2. EXPLODED VIEWS AND PARTS LIST 2.1 PACKING Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) NOTES: 1 2 7, 8, 9 10 5 13 12 11 3 2 14 4 15 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 11 5 6 7 8 5 6 7 8 C D F A B E PACKING parts List (2) CONTRAST TABLE DVR-RT500-S/UXTLCA and DVR-RT300-S/UXTLCA are constructed the same except for the following: Mark No. Description Part No. 1 Gift Sheet 791WHA0100 2 Package,Back 792WHA0519 3 Package,Front 792WHA0574 4 Gift Box See Contrast table (2) 5 Pad,DVD/VR (155 x 250) 795WCA0662 6 • • • • • • • 7 Instruction Book (English) J2D30901A 8 Guarantee Card J2D30902A 9 Warning Sheet J2D30928A 10 Polyethylene bag,Instruction JB5UD200 11 Transmitter (VXX2949) 076R0JZ010 12 RF Antenna Cable 06CPL02006 13 RCA Pin Cable 06CPBA2003 NSP 14 Battery Man Gan 1412004013 NSP 15 Polyethylene Bag Y817041000 Mark No. Description Part No. Mark No. Symbol and Description DVR-RT500-S /UXTLCA DVR-RT300-S /UXTLCA 4 Gift Box 793WCD1572 793WCD1587 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 12 1 2 3 4 1 2 3 4 C D F A B E 2.2 EXTERIOR SECTION A B D C Refer to "2.3 DECK ASSY (TOP SECTION)" "2.4 DECK ASSY (BOTTOM SECTION)". 6 1 4 5 55 55 55 55 48 27 46 52 52 52 52 54 54 54 54 56 35 44 53 23 52 19 13 17 12 15 20 8 9 16 (2/1) 16 (2/1) 28 54 52 52 52 59 59 59 40 24 26 25 52 32 31 30 30 33 39 33 29 52 37 37 52 51 51 36 45 42 55 2 3 No. 5 DRIVE Assy R7R No. 26 Shield. Deck 50 50 50 50 50 50 50 50 43 59 38 41 22 21 58 7 34 49 54 52 10 20 18 57 47 14 11 50 50 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 13 5 6 7 8 5 6 7 8 C D F A B E EXTERIOR SECTION parts List (2) CONTRAST TABLE DVR-RT500-S/UXTLCA and DVR-RT300-S/UXTLCA are constructed the same except for the following: * The DVD/HD MPEG PCB Assy diffrence is only EEPROM (IC4002) setting data. Refer to P.92. Mark No. Description Part No. 1 DVD/HD MPEG PCB Assy See Contrast table (2) 2 VCR MT PCB Assy A2D309A010 3 OPERATION PCB Assy A2D309A270 4 POWER PCB Assy A2D309A240 5 DRIVE Assy R7R (for Service) VXX2976 6 DECK Assy A2D309A420A 7 Front Cabi Assy See Contrast table (2) 8 Cabinet, Front See Contrast table (2) NSP 9 Plate, Display See Contrast table (2) 10 Flap, VCR 712WPJ0877 11 Flap, DVD 712WPQ0008 12 Cover, LED 713WPA0332 13 Glass, LED 713WPA0333 14 Sheet, LED 7230007689 15 Stopper, Button 738WPA0105 16 Button, Frame1 738WPB0040 17 Button, Frame2 738WPB0041 18 Spring, DVD-Flap 742WKA0001 19 Spring, Flap 743WKA0042 20 Cushion, Leg 800WFA0045 21 Bottom Cabi Assy 7G7610007A 22 Plate, Bottom 702WSA0227 23 Angle, Center 761WSA0175 24 Shield, Deck Assy 7G7610005D 25 Sheet (149.4 x 14 x T14) 7230007819 26 Shield, Deck 752WSA0437 27 Cushion 65TS10.5-20 8965TS2040 (40 x 15 x 6) 28 Cushion 65TS10.5-20 8965TS2020 (20 x 15 x 12) 29 Holder, Deck 701WPA0686 30 Holder, Deck 701WPA0751 31 Shield, Case Head Amp 752WSA0230 32 Spring, Earth Head Amp 753WUAA006 33 Holder, End Sensor 85OP700038 34 Sheet, Rating See Contrast table (2) 35 Sheet, Jack See Contrast table (2) 36 Cover, AC Head 752WSA0275 37 Shield, COMPO 752WSA0290 38 Shield, MPEG 752WSA0391 39 Shield, Jack 752WUA0008 40 Angle, DVD (L) 761WSA0150 41 Angle, DVD (R) 761WSA0151 42 Holder, Top 701WPA0781 43 Cabinet, Top 702WSB0092 44 Cushion (20 x 5 x T1) 800WFA0055 45 Cushion 65TS10-10 8965TS1017 (17.5 x 20 x 14) 46 Cushion 65TS10-5 8965TS1015 (15 x 20 x 16) 47 POP Label 7230007860 48 Holder, DVD 713WPA0337 49 Sheet, Serial 7220001196 NSP 50 Tape ZTA-570F-190BK 51 Screw 8109130B9U 52 Screw 810923070U 53 Screw 8109I30A0U 54 Screw 810923080U 55 Screw 8109K3060U 56 Screw 810723040U 57 Screw 8110E2680U 58 Screw 811022680U 59 Screw 810223060U Mark No. Description Part No. Mark No. Symbol and Description DVR-RT500-S /UXTLCA DVR-RT300-S /UXTLCA 1 DVD/HD MPEG PCB Assy A2D309AB10* A2D311AB10* 7 Front Cabi Assy 7A7010037C 7A7010040C 8 Cabinet, Front 701WPJ1285 701WPJ1308 NSP 9 Plate, Display 711WPD0662 711WPD0663 34 Sheet, Rating 7226310001 7226310002 35 Sheet , Jack 7230007843 7230007844 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 14 1 2 3 4 1 2 3 4 C D F A B E 2.3 DECK ASSY (TOP SECTION) To VCR MT PCB Assy CP102 CONTACT SIDE NON-CONTACT SIDE 34 35 42 48 48 29 37 47 5 4 8 23 18 52 52 22 20 19 11 10 26 27 38 24 46 2 3 32 1 9 39 50 51 31 30 36 49 40 41 51 51 16 17 13 14 21 15 7 6 12 33 53 28 25 AA AA AA AA AE AE AE AE AE AE AE AB AB AB AC AE AE AA AB AB AC AD AB AB AB AB AB AB AB AB AB AB AB AE AE www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 15 5 6 7 8 5 6 7 8 C D F A B E DECK ASSY (TOP SECTION) parts List Mark No. Description Part No. 1 Pinch Roller Block (VA) 85OA400240 2 AHC Assy 85OA500026 3 Worm 85OP600581 4 Base, AC Head 85OP500083 5 Spring, AC Head 85OP800324 6 Main Chassis Assy 85OA000516 7 Arm Idler Assy 85OA200090 8 Inclined Base T Unit 3S 85OA400223 9 P5 Arm Assy 2 85OA400232 10 Tension Arm Assy 2 85OA400235 11 Inclined Base S Unit 85OA400231 12 Spring, Locker 85OP800367 13 Cass, Holder 85OP900736 14 Cass, Side L 85OP900748 15 Cass, Side R 85OP900749 16 Locker, R 85OP900739 17 Link Unit 85OA900228 18 Post, Cass Guide 85OP000496 19 Reel, S (S) 85OP200316 20 Reel, T (S) 85OP200317 21 Gear, Idler 85OP200308 22 Holder, Tension 85OP400492 23 Cap. P4 85OP400520 24 Band, Tension 85OP400542 25 Connect, Tension 85OP400533 26 Arm, Brake T 85OP600573 27 Band, Brake T 85OP600584 28 Spring, Tension 85OP800322 29 Spring, Brake T 85OP800360 30 Lever, Link 85OP900743 31 Lever, Flap 85OP900744 32 Cass, Opener 85OP900745 33 Reflector, LED 85OP700035 34 Bracket, Top 3V 85OP900746 35 Cord Jumper (CD1501) 122H071704 36 Cord Jumper (CD1502) 122Y021902 37 Head (Audio Control)(H5001) 1523Q91003 38 Head (Full Erase)(H5002) 1543Q02014 > 39 Motor, Loading (M101) 1596S98002 40 Micro Motor (M2003) 1589S11020 > 41 Cylinder Unit Assy (UN4001) A5L1046500 42 Cord Jumper (CD102) ????? 43 • • • • • 44 • • • • • 45 • • • • • 46 Screw 8107226804 47 Screw 8107226404 48 Screw 8102120604 49 Screw 8109126604 50 Screw/Washer (A) 810A130404 51 Screw/Washer (A) 810A126504 52 Polyslider Washer 82Q264713N 53 Screw 8107226604 Mark No. Description Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 16 1 2 3 4 1 2 3 4 C D F A B E 2.4 DECK ASSY (BOTTOM SECTION) 8 6 23 10 2 4 15 16 24 7 3 5 9 13 22 19 18 17 21 1 20 22 22 12 11 14 AA AA AA AD AA AA AA AA AA AA AB AB AB AB AB AB AB AB AB AB AA AA AA AA AA AA AA AA www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 17 5 6 7 8 5 6 7 8 C D F A B E DECK ASSY (BOTTOM SECTION) parts List Mark No. Description Part No. 1 Belt, Capstan (S) 85OP200290 2 Main Chassis Assy 85OA000516 3 Clutch Assy 85OA200089 4 Loading Arm S Unit 85OA300065 5 Loading Arm T Unit 85OA300066 6 Gear, Clutch 85OP200311 7 Gear, Coupling 85OP200312 8 Lever, Clutch 85OP200313 9 Gear, Main Loading 85OP300194 10 Lever, Tension 85OP400490 11 Cam, Pinch Roller 85OP600577 12 Cam, Main 85OP600578 13 Rod, Main 85OP600579 14 Gear, Joint 85OP600582 15 Spring, Coupling 85OP800355 16 Spring, Ring 85OP800356 17 Holder, Capstan 85OP400549 18 Cord Jumper (CD1501) 122H071704 19 Cord Jumper (CD1502) 122Y021902 > 20 Capstan DD Unit (M2001) 1510S98042 21 Screw 8107226804 22 E-Ring 83ETW30000 23 Screw 8109126604 24 Polyslider Washer 82P184505N www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 18 1 2 3 4 1 2 3 4 C D F A B E 2.5 WIRING CABLE J653 J652 J651 V651 TP101 TP701 TP3002 CP8303 TP651 TU301 OS8001 J8004 CP8302 CP8301 CP1701 CP1703 J8002 J8005 J8006 J8003 J8001 J654 CP651 TP8301 TP8302 CP681 DVD/HD MPEG PCB POWER PCB OPERATION PCB DECK CD CP103 FE HEAD CP102 AC HEAD CD102 CD4001 CD504 CD651 CP506 CP502 CP504 CP7301 CP7302 CP7303 CP7304 CD7304 VCR MT PCB FAN MOTOR CD502 CD7301 CD7302 CD7303 CP4001 OS651 CP501 CD501 AC IN B C A D * All cables are ASSY parts. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 19 5 6 7 8 5 6 7 8 C D F A B E www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 20 1 2 3 4 1 2 3 4 C D F A B E 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1 BLOCK DIAGRAM 3.1.1 OVERALL BLOCK DIAGRAM TU301 Tuner / IF / Modulator IC8302 Y Video SW IC8303 C Video SW IC8305 Video SW IC8308 Video SW IC3001 (OEC0142) Syscon / Time R / Servo IC701 Hi-Fi / Sound / Head Amp / Dem : AUDIO SIGNAL : VIDEO SIGNAL VCR Deck IC8309 VCR Video SW IC8304 DVD Video SW IC101 Y/C Audio To RF IC801 Sound Decoder TUNER SW_Y_VIDEO STEREO A DVD Loader MPEG Encoder Audio Codec Vaddis V MPEG Decoder w/CPU MPEG Block Power Supply CV S L R S OP V CO L R CV L R U Y REAR CV S L R FRONT SW_C_VIDEO REAR CVBS FRONT CVBS REAR L/R FRONT L/R REAR CVBS FRONT CVBS SP/SLP CH1/2 SP/SLP CH1/2 NORMAL A TU/VCR_V FRONT L/R REAR L/R CVBS CVBS DVD AUDIO L/R AUDIO OUT L/R TUNER_VIDEO SIF Y/C_VIDEO Y/C_VIDEO RF AUDIO OUT CVBS OUT AUDIO OUT L/R 32.768kHz 10MHz 14.31818MHz 3.579545MHz ATAPI. FFC HEATER + HEATER – -22V TUNER +32V UNREG +3.3V AT +5.2V AT +13V AC 120V MOTOR +12V SIF REAR L/R FRONT L/R HF L/R HF COM TUNER_V REAR S-Y REAR S-C FRONT S-C FRONT S-Y SW_V_(FR/RE) DVD AUDIO L/R COAXIAL SPDIF YUV DVD Y/C OPTICAL www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 21 5 6 7 8 5 6 7 8 C D F A B E 3.1.2 MPEG BLOCK BLOCK DIAGRAM F P.CON+D5V E P.CON+12V D A5V C D5V B +3.3V A +1.8V B B C D B B B B B B VIDEO_IN_SEL VIDEO_IN_SEL A A B B B F E 1 RESET BD5229G IC4003 VIDEO IN C_VIDEO_IN Y_VIDEO_IN C_VIDEO_IN Y_VIDEO_IN COMPOSITE_IN TU_VIDEO AUDIO IN SCL,SDA DAC_L/R DAC_L/R SCL,SDA BR24L16FJ-WE2 EEPROM IC4002 C Y VIDEO OUT YUV CVBS_OUT AUDIO OUT SPDIF ALRCLKO/ABCLKO/AOUT0 ALRCLKO/ABCLKO/AOUT0 VADDIS_AMCLK SCL / SDA DAC_L/R VADDIS_AMCLK RESET WM8776SEFT/R AUDIO CODEC IC7301 AUDIO_IN_L/R_2 AUDIO_IN_L/R_1 BS_AUDIO_L/R TU_AUDIO_L/R SN74LVC1G125DCKR IC4010 AMCLK SW 1 2 4 1 2 4 6 MM1501XNRE VIDEO SW IC7302 ATDD0~15 ATCS0~1/ATDA0~2 ATIOW/ATIOR/ATINTRQ ATIORDY/ATDMACK DRVRST/ATDMARQ DVR-R07OR DVD-RW LODER DK4001 CP4001 ATAPI FFC 04_6274_040_000_800 ZR35100 IC4001 PNVMCE RAMDAT10~12 RAMDAT3~4 RAMADD2~4 FRAMBA0~1 FRAMADD0~1 FRAMADD5~11 FRAMDAT5~9 FRAMDAT16~31 RAMDAT16~31 RAMDAT0~15 RAMBA0~1 RAMDQM/RAMWE/PCLK RAMCAS/RAMRAS/RAMCS RAMADD0~12 IC4006 64MBIT FLASH LH28F640BFHE-PTTL80 IC4005 MT48LC8M16A2P-7E 128MBIT SDRAM MT48LC8M16A2P-7E 128MBIT SDRAM IC4004 256MBIT SDRAM HY57V561620CT-7 IC4008 IC4009 MBA0~1 MCAS/MRAS/MCS MDQM/MWE/MCLK MA0~12 MD16~31 HY57V561620CT-7 256MBIT SDRAM IC4007 MD0~15 CVBSIN ZR36750E SBVALID,SBDAT,SBCLK,SBREQ VIDHS,VIDVS,VIDCLK,VIDVLD,VID0_7 DATA LINE MPEG_DATA_IN,MPEG_DATA_OUT VADDIS_INT,MPEG_CS,MPEG_CLK AMCLK_SEL MPEG 27M_OSC I55_TX0,I55_RX0 MPEG ENCODER 27M_OSC I55_AODAT I55_AODAT I55_AMCLK I55_ALRCLK,I55_ABCLK I55_ALRCLK,I55_ABCLK ADC_ADAT ADC_ADAT ADC_ADAT 12 5 11 1,48 13,10 7,4,6 19,18 26,27 3,2 45,44 47,46 147 14 69 237 257,121 17,37 117 108,97,107 118 127 144 294,314,293,313,292, 312,291,311,270,250, 271-273,253,274,254, 34 56 100,110 99 57 109,119,141 287,307,289,309,308, 290,310,248, 305,284,304,303,283,264,244, 265,245,266,285,246,220 282,302,281,301,280,300, 299,298,278,279,260,240, 261,262,242,263 287,307,305,284,264,244,265,245,266,285,246, 312,291,311,270,250,282,302,281,301,280,300, 299,298,278,279,260,240,261,262,242,263, 304,303,283,313,292,271,272,273,297 62,42,1,22,63,43,64,44,4,24,24,3,23,2,84,83,104, 111,112,113,101,102,103,82,41,61,81,52,21 79,98,142,128 215,214,156,216, 157,158,171,172170,185,186,184 315,296 183 177 180 207,206,203,205, 201-194 188,186,189,184 192,190 102,99,95,91,89, 87,83,81,82,85, 88,90,93,97,100, 103 64,61 75,73,72, 79,77,70, 54,51,48,46,47, 50,52,55,59,63 ,57,66,68 44,41,38,36,33, 29,26,22,21,24, 28,31,34,37,40,43 9 2 4 182,181 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 22 1 2 3 4 1 2 3 4 C D F A B E 3.1.3 Y/C AUDIO / CCD / HEAD AMP BLOCK DIAGRAM 30 2 22 32 10 21 67 65 7 9 36 6 8 34 55 54 53 57 4 3 5 78 76 H.AMP SW REC AMP CP102 6 5 4 AUDIO REC AUDIO PB CTL+ HEAD AUDIO CONTROL 3 2 1 AE HEAD(+) AE HEAD(-) CTL- CTL+ CTL- Y/C/AUDIO/CCD/HEAD AMP IC IC101 LA71206 39 Q107 BUFFER TIMMING CCD OUT DRIVER CLAMP 37 58 60 59 24 25 66 H.SW 72 73 74 H.SW H L H L H L PB.EE P R WC DC NL EMPHA REC FM-EQ FM MOD P R KIL FM AGC DELAY PB FM-EQ PB PHASE-EQ P R C-LPF B-UP AMP ACC AMP Main CONV AUTO BIAS P R KIL B.D. PB AMP 3.58M BPF1 DOUBLE LIM FM DEM SUB LPF MAIN DE-EM P R Y-LPF YNR/ COMB N.L. DEEM NC1 Y/C MIX SYNC SEP VCA CLAMP 1/2 FBC QV/QH 6dB P R P R V-AGC L101 CLAMP EQ AMP LINE AMP MUTE ALC Y/C_CS Y/C_DATA Y/C_CLK H. AMP_SW C. ROTARY H. SW ENV. DET COMP DUMMY_V. SYNC C.SYNC F/R_V_IN TU_V_OUT NORMAL_A_IN NORMAL_A_OUT 6 2 3 1 5 Q105 BIAS CTL 11 4 P. CON + 5V H.AMP SW/ AUDIO MUTE C ROT RF SW IN ENV DET CONP OUT Q104 BIAS OSC Q103 SW Q101, Q102 AUDIO PB SW HF1 HF2 HI-FI/DEMODU LATOR HF_COM COIL, BIAS OSC X101 3.578545M Hz VX01 50 49 PULL 41 Q109 BUFFER TUNER/JACK SYSCON HI-FI/DEMODU LATOR 80 SERIAL DECODER AUDIO_MUTE-H V.REC_ST-H LPF ALC DET P R SYSCON SYSCON EP/LP-CH1 (R) EP/LP-CH2 (L) CP101 6 5 4 SP-CH1 (R) SP_COM SP-CH2 (L) CYL 3 2 1 EP/LP_COM HF2 (L) HF_COM HF1 (R) 7 8 9 FE HEAD (HOT) FE HEAD (GND) FE HEAD 2 1 CP103 DETAL ENH 28 DVD_V_OUT FSC 26 VCR_V_OUT1 Q106 BUFFER AV SW AV SW 3.58M BPF2 69 70 R142 FSC AUDIO SIGNAL (PB) AUDIO SIGNAL(REC) RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL TUNER VIDEO SIGNAL PLAYBACK COLOR SIGNAL www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 23 5 6 7 8 5 6 7 8 C D F A B E 3.1.4 SYSTEM CONTROL BLOCK DIAGRAM SYSCON/TIMER/SERVO IC3001 OEC0142B Y/C/AUDIO/ CCD/HEAD AMP POWER ON-L DRUM PWM MS SEN-B POWER FAIL Y/C CS DUMMY V.SYNC 41 107 27 37 105 109 AV SW VCR_P_ON-L POWER_FAIL VIDEO H.SW DFG/PG 104 AUDIO MUTE-H 58 85 TUNER /JACK LD M CTL 97 BOT-H EOT-H 26 AT 5.2V BOT SENSOR Q3008 EOT SENSOR Q3006 2 CYL FG/PG 4 CAP PWM 108 CAP LIMIT 84 CAP FULL 102 CAP FG 9 CAP FWD-L 98 9 10 I LIMIT CAP CTL 11 CAP VOC 12 CAP/M/F/R MS SEN-A 28 MS_SEN A Q3005 MS_SEN B Q3004 2 3 4 1 CAP./LDM/ CYL UNIT H.AMP SW Y/C_CS DUMMY_V.SYNC H.SW AUDIO_MUTE-H H.AMP_SW V ENV 24 ENV.DET CTL(+) 3 CTL(-) 4 RF_SW AFT S.CURVE 33 54 TV/VCR 86 IIC SDA IIC CLK 61 62 RF_SW TV/VCR SDA SCL AFT-S.CURVE CTL+ CTL- RESET 77 2 1 3 IC3003 XC61CN3102SR AT+5V [M-CON] SYSTEM RESET 5 6 EEPROM IC3099 S-24C08AFJA-TB-01 Y/C DATA 86 Y/C CLK 87 Y/C_DATA Y/C_CLK C.SYNC 111 C.SYNC SCL SDA COMP COMP 92 DVD_V_SW_R-H HIFI H.SW 106 HIFI ENV 32 HIFI_H.SW HIFI_ENV.DET POWER MUTE L 94 POWER_MUTE-L HIFI/ DEMODULATOR DRIVE_ON-H 50 DRIVE_ON-H 65 MP DATA IN TUNER A MUTE H 53 TUNER_A_MUTE-H STEREO SE L 31 ST SELECT 64 MP DATA OUT 25 C.ROTARY 99 C.ROTARY 5 LDM CTL CP3001 OPERATION/ DISPLAY VADDIS_RESET VADDIS INT 44 83 REAR S SW KEY-A 30 45 KEY-B 29 MPEG_RESET VADDIS INT REAR S SW KEY-A KEY-B FL_CLK REM IN 43 48 FL_CLK REM_IN FL_DATA 49 FL_DATA FL_CS 47 FL_CS CYL _CTL 2 3 4 1 2 3 4 1 REEL SENS Q3002 REEL SENS Q3001 REEL T 70 REEL S 69 2 3 4 1 P.CON+5V 59 60 MPEG_DATA 42 MPEG_CLK HiFi/DEMODULATOR CH A MUTE-H DVD_V_SW_F-H VADDIS D OUT VADDIS IIC SDA VADDIS IIC CLK CH A MUTE-L VADDIS D IN SCL SDA AUDIO_MUTE-H V.REC ST-H 71 V.REC_ST-H 100 101 X3001 10MHz OSC 2 OSC 1 78 80 X3002 32.678KHz X1 X2 75 76 CENT LED D3001 V_SW_VCR-H 73 V_SW_VCR-H REGULATOR 1 CAP FG CAP_CVO FRONT-S-SW 52 FRONT-S-SW VCR-H 95 VCR-H 19 V.OUT CV.OUT V.REC_ST-H LD/CY VCO 8 AT+12.6V Q3007 SW X3003 14.31818KHz 4FSC OUT 22 21 4FSC IN 63 91 CH_V_MUTE-H VADDIS_CLK CH_V_MUTE-H MP_CLK 38 39 MPEG 5V ON-H MPEG P ON-L MPEG 5V ON-H MPEG P ON-L 46 FIP_ON-L FIP_ON-L 51 TAB_SW 88 17 35 93 16 CVIN2 CVIN1 SD JUDGE VCR_V_SW_F-H VCR_DUB-H VCR_DUB-H VCR_V_SW_R-H SYNC.DET SW_V_OUT AV SW TUNER/JACK AV SW AV SW RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL SW3001 LSA-1144EAU www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 24 1 2 3 4 1 2 3 4 C D F A B E 3.1.5 REGULATOR BLOCK DIAGRAM 13 12 9 8 7 6 5 4 2 TUNER+32V P.FAIL DRIVE ON H UNREG+3.3V UNREG+3.3V AT+5.2V AT+5.2V AT+13V MOTOR+12V POWER Q1716 P.CON+12V SW. Q1712 VOLTAGE CTL. Q1713 3.3V REG Q1722 MPEG P.CON SW Q1720 P.CON 5V SW. Q1721 MPEG+5V SW Q1723 M-CON AT 5V SW. AT+12.6V AT+5.2V -22V AT+5V(M-CON) P.CON+5V MP_P.CON+5V P.CON+12V POWER FAIL MPEG POWER ON-L MPEG 5V ON-H SYSCON HEATR_DC+ MP-P.CON+3.3V OPERATION/ DISPLAY Q1724 M-CON POWER SW. Q1701 MP POWER SW. 16 15 14 HEATER+ HEATER- -22V 5 8 VOLT CURRENT CONTROL IC1701 LM2902D 14 HEATR_DC- +32V DRIVE ON-H 7 Q1708 1.8V REG Q1709 VOLTAGE CTL MP-P.CON+1.8V SYSCON OPERATION/ DISPLAY HI-FI/DEMODULATOR CAP_VCO Q1717 P.CON SW. Q1703, Q1707, Q1710, Q1711 HEATER SW, HFIP SW TUNER/JACK FIP_ON-L VCR_P_ON-L www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 25 5 6 7 8 5 6 7 8 C D F A B E 3.1.6 OPERATION / DISPLAY BLOCK DIAGRAM STOP FF/CUE REC/OTR REW/REV 21 32 V651 HNV-09SS48 4 12 25 14 42 34 FIP DRIVER IC IC651 PT6315 34 35 1 2 1 3 OS651 2 3 J651 2 J652 2 J653 D602 -22V HEATER DC- HEATER DC+ FL_CS FL_DATA FL_CLK AT+5.2V REM_IN KEY-B KEY-A FRONT_A_IN_R FRONT_A_IN_L FRONT_V_IN REGULATOR SYSCON AV SW GND KEY-B/C KEY-A DVD LED AT+5.2V 5 3 2 1 CH DOWN OPEN/CLOSE SYSCON 43 13 7 9 30 8 4 5 3 2 1 4 PLAY SW681 SW682 SW683 SW684 SW685 SW686 SW687 D681 CH UP SW688 4 3 J654 6 1 2 FRONT_Y_IN FRONT_C_IN FRONT_S_SW POWER EJECT DVD/VCR SW653 SW652 SW651 FRONT_A_IN_L FRONT_A_IN_R HIFI/ DEMODULATOR AUDIO SIGNAL(REC) RECORD LUMINANCE SIGNAL RECORD COLOR SIGNAL www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 26 1 2 3 4 1 2 3 4 C D F A B E 3.1.7 HiFi / DEMODULATOR BLOCK DIAGRAM HIFI AUDIO/H.AMP/DEM IC IC701 AN3663FBP 57 15 53 27 42 10 29 30 36 48 43 28 24 21 22 45 62 61 HIFI_H.SW SIF_OUT AUDIO_MUTE-H V. REC_ST-H HIFI_ENV. DET SCL SDA HF2 HF_COM FSC HF1 NORMAL_A_OUT NORMAL_A_IN TUNER/JACK SYSCON Y/C/AUDIO/CCD /HEAD AMP INPUT SW AMP AMP OUTPUT SW PNR BPF FM LIM DEM BLOCK AMP AMP AGC LOGIC VCO-FO ADJ LOGIC DBX NOISE REDUCTION L/R MIX REC LPF VCO 14 9 FRONT_A_IN_L FRONT_A_IN_R OPERATION/ DISPLAY DVD_A_OUT_L AV SW DVD_A_OUT_R 3 2 REAL_A_IN_L REAL_A_IN_R 19 18 14 TU_A_OUT STEREO IC IC801 AN5829S 22 21 ST_A_OUT_L ST_A_OUT_R TUNER/JACK HIFI_A_OUT_L HIFI_A_OUT_R AV SW 25 P.CON+5V 58 P.CON+12V 51 P.CON+5V 7 P.CON+5V Y/C/AUDIO/CCD /HEAD AMP REGULATOR 59 ALC_A_OUT TUNER/JACK 56 ST_SELECT SYSCON AUDIO SIGNAL (PB) AUDIO SIGNAL(REC) TUNER AUDIO SIGNAL www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 27 5 6 7 8 5 6 7 8 C D F A B E 3.1.8 TUNER / JACK BLOCK DIAGRAM Y UV OUT J8006 S-VIDEO OUT J8004 REAR OUT JACK1 J8005 S-VIDEO IN J8001 REAR IN JACK J8002 DVD AUDIO OUT/COAXIAL J8003 OPTICAL OS8001 Q8027 Q8029 Q8025 MUTE SW MUTE SW MUTE SW MUTE SW MUTE SW 2 3 5 3 4 5 3 2 3 4 6 2 3 2 3 5 1 4 6 Q8013 Q8012 MUTE SW Q8016 MUTE SW MUTE SW Q8018 Q8017 MUTE SW MUTE SW Q8036 Q8019 BUFFER Q8001 BUFFER Q8002 MUTE SW Q8006 D_AUDIO DRIVER Q8007 MUTE SW Q8005 MUTE SW Q8004 MUTE SW MUTE SW Q8022 Q8020 MUTE SW Q8003 Q8023 MUTE SW MUTE SW Q8021 TU301 8 4 2 10 11 17 14 12 1 5 13 MUTE SW Q303 DVD_A_OUT-R DVD_A_OUT-L SPDIF AV SW V[PR]_V_OUT U[PB]_V_OUT Y[G]_V_OUT Q8009 ASP CTL Q8010 ASP CTL Q8008 ASP CTL DVD_Y_V_OUT DVD_C_V_OUT ASP1 ASP2 HiFi_A_OUT-L HiFi_A_OUT-R MUTE-L ZERO-MUTE-L REAR_C_IN REAR_Y_IN REAR_A_IN_L REAR_A_IN_R REAR_A_IN_L REAR_A_IN_R ALC_A_OUT TU_A_OUT SIF_OUT REAR_V_IN FSC TU_V_OUT VCR-H P_MUTE-L AFT-S.CURVE SCL SDA REAR_S_SW V_OUT TV/VCR RF_SW TU_A_MUTE-H MUTE SW Q302 AV SW SYSCON HiFi/ DEMODULATOR BUFFER Q8015 Y/C/AUDIO/CCD /HEAD AMP HiFi/ DEMODULATOR AV SW 15 +32V REGULATOR AUDIO SIGNAL (PB) AUDIO SIGNAL(REC) PLAYBACK LUMINANCE SIGNAL PLAYBACK COLOR SIGNAL LUMINANCE SIGNAL TUNER AUDIO SIGNAL COLOR SIGNAL TUNER VIDEO SIGNAL DIGITAL AUDIO SIGNAL (PB) TU_V_OUT AV SW BUFFER Q301 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 28 1 2 3 4 1 2 3 4 C D F A B E 3.1.9 AV SW BLOCK DIAGRAM AUDIO SIGNAL (PB) AUDIO SIGNAL(REC) PLAYBACK LUMINANCE SIGNAL PLAYBACK COLOR SIGNAL TUNER VIDEO SIGNAL LUMINANCE SIGNAL COLOR SIGNAL DIGITAL AUDIO SIGNAL (PB) TU AUDIO L VCR AUDIO L CP8301 10 12 14 REAR AUDIO R REAR AUDIO L TU AUDIO R 16 18 20 VCR AUDIO R FRONT AUDIO L FRONT AUDIO R F/R Y IN 8 6 4 F/R C IN 2 U/B_OUT TV/VCR VIDEO CP8302 10 12 14 CVBS_OUT Y_OUT Y/G_OUT 16 18 20 V/R_OUT C_OUT AUDIO_L_OUT AUDIO_R_OUT 8 6 4 CVBS_IN 2 MUTE CP8303 15 16 ASP2 ASP1 17 18 ZERO SPDIF VADDIS INT IIC DATA 13 12 11 IIC CLK 10 5 6 7 MPEG-DATA OUT MPEG-DATA IN MPEG CLK 9 RESET GND 4 7 2 AV SW (VCR/TUNER VIDEO SW) IC8305 NJM2534V 1 3 4 6 Q8311 BUFFER 9 2 SNC DET IC IC8307 LA7210 1 6 10 6 2 1 AV SW (VCR/TUNER VIDEO SW) IC8308 NJM2246-TE1 3 7 6 2 1 3 7 AV SW (VCR FRONT/REAR VIDEO SW) IC8309 NJM2533V 6 2 1 3 7 4 AV SW (DVD FRONT/REAR VIDEO SW) IC8304 NJM2534V 6 2 1 3 7 4 AV SW (FRONT/REAR(SW)) IC8303 NJM2534V 6 2 1 3 7 4 AV SW (FRONT/REAR Y SW) IC8302 NJM2534V 7 8 1 3 5 AMP IC8301 NJM4580M(TE1) P.CON+12V (REFULATOR) ST_A_OUT_L HiFi_A_OUT_L REAR_A_IN_R REAR_A_IN_L ST_A_OUT_R HiFi_A_OUT_R FRONT_A_IN_L FRONT_A_IN_R REAR_Y_IN REAR_C_IN FRONT_Y_IN FRONT_C_IN MUTE-L ASP2 ASP1 ZERO_MUTE-L SPDIF VADDIS INT MPEG DATA MPEG CLK MP_DATA OUT MP_DATA IN MP_CLK MPEG_RESET VCR_DUB-H VCR_V_OUT1 TU_V_OUT V[PR]_V_OUT U[PB]_V_OUT Y[G]_V_OUT DVD_Y_V_OUT DVD_V_OUT REAR_V_IN FRONT_V_IN F/R_V_IN SYNC DET SW_V_OUT V_SW_VCR_H VCR_V_SW_R_H DVD_C_V_OUT DVD_A_OUT_L DVD_A_OUT_R TUNER/JACK SYSCON HiFi/ DEMODULATOR TUNER/JACK DISPLAY/ OPERATION TUNER/JACK DISPLAY/ OPERATION SYSCON TUNER/JACK X8301 CSB506E5 Y/C/AUDIO/CCD /HEAD AMP TUNER/JACK Y/C/AUDIO/CCD /HEAD AMP SYSCON TUNER/JACK DISPLAY/ OPERATION P.CON+5V CH_V_MUTE_H DVD_V_SW_R-H Y/C/AUDIO/CCD /HEAD AMP REGULATOR SYSCON OPERATION/ DISPLAY HiFi/ DEMODULATOR DVD_A_OUT_R DVD_A_OUT_L TUNER/JACK www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 29 5 6 7 8 5 6 7 8 C D F A B E 3.1.10 POWER BLOCK DIAGRAM Q502 Q501 CONTROL SW. T501 14 4 2 PHOTO COUPLER IC503 PS2561L1-1-V(W) L501 AC IN D505, D506 D502, D503 6 11 16 15 14 13 12 9 8 7 6 5 4 2 HEATER+ HEATER- -22V TUNER+32V P.FAIL DRIVE ON H UNREG+3.3V UNREG+3.3V AT+5.2V AT+5.2V AT+13V MOTOR+12V CP502 REGULATOR 4 1 P.CON+D5V P.CON+12V CP504 DVD LOADER UNIT 18 IC502 DRIVE 12V REG KIA278R12PI 1 2 IC501 KIA431A-AT VOLTAGE CTL. IC 3 1 3 4 1 2 12 13 16 1 P.CON+12V CP506 15 Q505 DRIVE 5V SW. FAD MOTOR Q503 SAFTY SW. 4 Q504 SAFTY SW. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 30 1 2 3 4 1 2 3 4 C D F A B E 3.2 OVERALL WIRING DIAGRAM 10 9 8 7 6 4 5 3 2 1 CP1703 10 9 8 7 6 4 5 3 2 1 CP7304 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 4 5 3 2 1 CP7301 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 4 5 3 2 1 CP8302 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 4 5 3 2 1 CP8301 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 4 5 3 2 1 CP7302 18 17 16 15 14 13 12 11 10 9 8 7 6 4 5 3 2 1 CP7303 18 17 16 15 14 13 12 11 10 9 8 7 6 4 5 3 2 1 CP8303 OS8001 OPTICAL 1 2 3 H1 H1 H2 E E J8003 DVD AUDIO OUT COAXAL 1 2 3 4 5 H1 H1 H2 E E J8006 REAR OUT JACK YUV OUT 1 2 3 4 5 J654 FRONT IN JACK S VIDEO 1 2 3 4 5 6 4 3 2 1 4 3 2 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 4 5 3 2 1 2 1 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CP506 NC NC NC(GND) NC(GND) NC(GND) DRIVE ON-H NC(GND) MOTOR_GND DRIVE ON-H DK4001 CP4001 CP1701 CP504 CP502 ATDD7 ATDD8 ATDD6 ATDD9 ATDD5 ATDD10 ATDD4 ATDD11 ATDD3 ATDD12 ATDD2 ATDD13 ATDD1 ATDD14 ATDD0 ATDD15 SPSYNC ATIORDY ATDMACK ATINTRQ ATDA1 ATDA0 ATDA2 ATCS0 ATCS1 ATDIOR ATDIOW ATDMARQ DRVRST CD4001 FFC MOTOR+27V MOTOR+27V 19 20 18 16 17 15 14 13 7 6 5 4 3 2 1 8 12 10 11 9 CD7304 BOOT1 BOOT0 RESET GND TD D GND D GND P.CON+12V MOTOR GND P.CON+D5V P.CON+12V MOTOR GND VSC CLK VSC CLK VSC ON-H VSC DATA VSC ON-H MPEG DATA OUT MPEG DATA IN MPEG DATA OUT MPEG DATA IN MPEG CLK MPEG CS RESET IIC_CLK IIC_DATA VADDIS INT VADDIS INT SPDIF P-H/I-L ASP2 ASP1 MUTE ZERO GND GND GND GND CVBS_OUT C_OUT GND GND Y_OUT GND Y/G_OUT GND V/R_OUT U/B_OUT GND GND BS/TU V IN GND F/R C IN GND F/R Y IN GND GND FRONT AUDIO R FRONT AUDIO L GND GND REAR AUDIO R REAR AUDIO L GND TU AUDIO R GND TU AUDIO L VCR AUDIO L VCR AUDIO R GND GND CVBS_OUT BS/TU V IN V/R_OUT U/B_OUT Y/G_OUT Y_OUT C_OUT GND CVBS_IN GND AUDIO_R_OUT AUDIO_L_OUT GND GND GND GND GND GND GND GND +1.8V +1.8V +3.3V +3.3V MPEG5V GND GND GND 7 6 5 4 3 2 1 CP4007 RD 5V 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 9 18 17 16 15 14 13 12 11 10 6 5 4 3 2 1 8 7 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 9 18 17 16 15 14 13 12 11 10 6 5 4 3 2 1 8 7 VSC DATA MPEG CS F/R C IN F/R Y IN VCR AUDIO R VCR AUDIO L GND GND GND FRONT AUDIO R GND FRONT AUDIO L GND REAR AUDIO R GND REAR AUDIO L GND TU AUDIO R GND TU AUDIO L GND GND +1.8V +1.8V +3.3V +3.3V MPEG5V GND GND GND WIRE MUTE ZERO IIC_DATA IIC_CLK GND ASP2 ASP1 P-H/I-L RESET GND MPEG CLK SPDIF CVBS_IN AUDIO_R_OUT AUDIO_L_OUT CD7301 FFC 15 16 17 18 19 20 9 14 13 12 11 10 6 5 4 3 2 1 8 7 CD7302 FFC 9 9 13 12 11 10 13 12 11 10 6 5 4 3 2 1 6 5 4 3 2 1 8 7 8 7 14 14 15 16 17 18 19 20 15 16 17 18 19 20 CD7303 FFC 15 16 17 18 15 16 17 18 9 9 14 13 12 11 10 14 13 12 11 10 6 5 4 3 2 1 6 5 4 3 2 1 8 7 8 7 MOTOR+12V MOTOR GND AT+13V AT+5.2V AT+5.2V UNREG+3.3V UNREG+3.3V GND GND P.FAIL TUNER+32V -22V HEATER - HEATER + MOTOR+12V MOTOR GND AT+13V AT+5.2V AT+5.2V UNREG+3.3V UNREG+3.3V GND GND P.FAIL TUNER+32V -22V HEATER - HEATER + INPUT VCC GND GND NC GND NC GND GND GND GND GND 2 1 WIRE CD504 WIRE P.CON+D5V 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 9 18 17 16 15 14 13 12 11 10 P.CON+12V 6 5 4 3 2 1 8 7 M M501 FAN MOTOR DRIVE ASSY R7R (VXX2976) POWER PCB ASSY (A2D309A240) C A 1/6 - A 6/6 A CP501 A3963WV2-3PD 1 2 BLADE WIDE BLACK WHITE 2 1 CD501_6 1209619904 AC120V_60Hz DVD/HD MPEG PCB ASSY (DVR-RT500-S : A2D309AB10) (DVR-RT300-S : A2D311AB10) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 31 5 6 7 8 5 6 7 8 C D F A B E J8001 REAR IN JACK S-VIDEO IN 1 2 3 4 5 6 7 E E H1 NC H1 H2 J8002 REAR IN JACK 1 2 3 4 5 6 H1 H1 H2 E E J8005 REAR OUT JACK 1 2 3 4 5 TU301 1 10 11 12 13 14 15 16 17 18 19 2 20 21 3 4 5 7 8 9 J8004 REAR OUT JACK Y/C SEPA 1 2 3 4 5 6 H NC E J651 FRONT IN JACK AUDIO IN R 1 2 3 H E J653 FRONT IN JACK VIDEO 1 2 H E J652 FRONT IN JACK AUDIO IN L 1 2 5 4 3 2 1 CP651 5 4 3 2 1 CP681 Vout B+ GND OS651 1 2 3 2 1 CP103 7 6 5 4 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 9 8 7 6 4 5 3 2 1 CP101 6 5 4 3 2 1 6 5 4 3 2 1 H5002 CP3001 CD102 FFC FPC CH.SW A.OUT AFT OUT BT WIRE CD651 WIRE X’TAL DATA SIF OUT KEY-B KEY-B FE HEAD (GND) FE HEAD (HOT) D-COM D-U OUT D-V OUT D-W OUT D-PG OUT AUDIO REC AUDIO PB AE HEAD(-) AE HEAD(+) HF1 (R) HF2 (L) SP-CH1 (R) EP/LP COM SP-CH2 (L) EP/LP-CH1 (R) EP/LP-CH2 (L) AT+5.2V DVD LED KEY-A GND AT+5.2V DVD LED KEY-A GND TM601 COMMAND TRANSMITTER FE HEAD (GND) FE HEAD (HOT) FULL ERASE HEAD ASS’Y 2 1 IF OUT CLOCK V.OUT ADDRESS RF AGC V.IN CONTROL +B A.IN AE HEAD(-) AE HEAD(+) AUDIO PB AUDIO REC LD/CY VCO CP102 3 2 1 5 4 6 9 8 7 7 6 5 4 3 2 1 FFC 7 6 5 4 3 2 1 3 2 1 5 4 6 9 8 7 3 2 1 5 4 6 3 2 1 5 4 6 CTL- CTL+ AE CTL- CTL+ H5001 HEAD AUDIO CONTROL ASS’Y AUDIO CONTROL CYLINDER UNIT WHITE RED M101 LOADING MOTOR LM M-GND D-PG GND EP/LP HEAD SP HEAD HI-FI HEAD SP COM HF COM UN4001 CAPSTAN DD UNIT M2001 CYL CTL CAP FG CAP VCO VCC CAP CTL CYL FG/PG LDM CTL GND MOTOR GND I LIMIT CAP.M/F/R O G VCC MR FG SENSOR ROTOR MAGNET COIL MAIN LOGIC SWITCH OUT HALL SENSOR IN HALL VCC HALL ÷ When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST". ÷ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. ÷ : The power supply is shown with the marked box. VCR MT PCB ASSY (A2D309A010) B 1/7 - B 7/7 B OPERATION PCB ASSY (A2D309A270) D www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 32 1 2 3 4 1 2 3 4 C D F A B E 3.3 DVD/HD MPEG PCB ASSY(1/6) JG4018 JG4014 JG4015 JG4019 JG4020 C4151 0.001 B C4152 0.01 B C4078 0.1 F C4085 0.001 B C4084 0.01 B C4067 0.1 F C4068 0.001 B C4062 0.1 F C4069 0.01 B C4063 0.1 F C4072 0.1 F C4073 0.1 F C4082 0.1 B C4083 0.1 B C4088 0.01 F C4095 0.1 F C4096 0.1 B C4097 0.1 B C4091 0.1 B C4070 0.1 F C4064 0.1 F C4066 0.1 F C4074 0.1 F C4101 0.01 B C4075 0.1 F C4099 0.1 F C4090 0.1 F C4103 0.1 F C4092 0.1 F C4079 0.1 F C4104 0.01 B C4087 0.001 B C4086 0.01 B C4071 0.001 B C4065 0.01 B C4146 0.001 B C4150 0.01 B C4089 0.1 F C4157 0.1 F C4080 0.1 F C4159 0.1 F C4100 0.1 F C4160 0.1 F C7355 47P CH C7356 47P CH C7357 47P CH B4003 HCB2012K -600T25 B4002 HCB2012K -600T25 R4043 4.7K R4017 4.7K R4018 4.7K R4019 4.7K R4035 4.7K 203 204 205 206 207 208 1 10 11 12 13 14 15 16 17 18 19 2 20 21 22 23 24 25 26 27 28 29 3 30 31 32 33 34 35 36 37 38 39 4 40 41 42 43 44 45 46 47 48 49 5 50 51 52 53 54 55 56 57 58 6 7 8 9 IC4007 HY57V561620CT-7 256Mbit SDRAM 1 10 11 12 13 14 15 16 17 18 19 2 20 21 22 23 24 25 26 27 28 29 3 30 31 32 33 34 35 36 37 38 39 4 40 41 42 43 44 45 46 47 48 49 5 50 51 52 53 54 6 7 8 9 IC4008 HY57V561620CT-7 256Mbit SDRAM 1 10 11 12 13 14 15 16 17 18 19 2 20 21 22 23 24 25 26 27 28 29 3 30 31 32 33 34 35 36 37 38 39 4 40 41 42 43 44 45 46 47 48 49 5 50 51 52 53 54 6 7 8 9 C4081 47 6.3V V-S C4094 47 6.3V V-S C4076 47 6.3V V-S C4077 47 6.3V V-S C4098 47 6.3V V-S C4102 47 6.3V V-S C4093 47 6.3V V-S I55_EJTDO VID0 I55_EJTDI VID1 VID2 VID3 I55_EJTCK VID4 VID5 I55_EJTMS VID6 VID7 VIDVS VIDHS VIDVLD VIDCLK SBCLK SBREQ VIDHS VIDVS VIDVLD VIDCLK SBDAT SBVALID I55_TX0 I55_RX0 I55_GPIO0 I55_GPIO2 27MHZ_OSC I55_AMCLK I55_ALRCLK I55_ABCLK I55_AODAT I55_RESET MD0 MD15 YIN MD1 MD14 CVBSIN MD2 MD13 MD3 MD12 MD4 MD11 CIN MD5 MD10 I55_RX1 MD6 MD9 I55_TX1 I55_AMCLK MD7 MD8 I55_ALRCLK I55_ABCLK ADC_ADAT I55_EJTDI MDQM MWE MDQM I55_EJTDO MCAS MCLK I55_EJTMS MRAS I55_EJTCK MD24 MCS MA12 MD23 MBA0 MA11 MBA1 MA9 MD25 MA10 MA8 MA0 MA7 MD22 MA1 MA6 MD26 MA2 MA5 MD21 MA3 MA4 MD27 MD20 MD28 MD19 MD29 MD18 MD16 MD31 MD30 MD17 MD17 MD30 MD18 MD29 MD31 MD16 MD19 MD28 MA3 MD20 MD27 MA4 MA2 MD21 MD26 MD22 MD25 MA5 MA1 MA6 MD23 MD24 MDQM MWE MDQM MCAS MCLK MRAS MCS MA12 MBA0 MA11 MBA1 MA9 MA10 MA8 MA0 MA7 MA10 MA1 MA6 MA0 MA7 MA2 MA5 MA3 MA4 YIN CVBSIN CIN +1.8V +1.8V +3.3V +3.3V D5V D5V GND GND GND GND FROM/TO MPEG VSS DQ15 VSSQ DQ14 VCCQ DQ13 DQ12 DQ11 VSSQ DQ10 DQ9 VCCQ DQ8 VSS UDQM CLK CKE A11 A9 A8 A7 A6 A5 A4 VSS VCC A3 A2 A1 A0 RAS CAS WE LDQM VCC DQ7 VSSQ DQ6 DQ5 VCCQ DQ4 DQ3 VSSQ DQ2 DQ1 VCCQ DQ0 VCC A12 CS A10 BA0 BA1 NC NC VSS DQ15 VSSQ DQ14 VCCQ DQ13 DQ12 DQ11 VSSQ DQ10 DQ9 VCCQ DQ8 VSS UDQM CLK CKE A11 A9 A8 A7 A6 A5 A4 VSS VCC A3 A2 A1 A0 RAS CAS WE LDQM VCC DQ7 VSSQ DQ6 DQ5 VCCQ DQ4 DQ3 VSSQ DQ2 DQ1 VCCQ DQ0 VCC A12 CS A10 BA0 BA1 NC NC FROM/TO AV I/O FROM/TO AUDIO 0 0 0 1.0 1.9 1.5 1.3 1.1 1.5 3.4 4.7 3.2 3.4 0 NC NC 3.3 3.0 3.4 0 3.0 3.0 0.9 0.2 0 2.5 3.4 0.3 1.8 0.4 0.4 0 0.2 0 0.2 0.2 3.4 0.2 0.2 3.2 0 0.1 3.2 3.4 0.1 0.2 0 0.2 0.2 0.2 3.4 0.2 0.2 0.2 0.1 0 0.2 3.4 0.4 1.8 VDDP VDDP VDDP VDDP VDDP VDDC VDDC VDDIP HSYNC VSYNC VIDVALID VIDCLK GPIO6 GPIO3 VDDP EJTDI EJTCK EJTDO DUPRD1 DUPTD1 GNDC GNDP GNDP GNDP GNDP GNDP RAMDAT31 RAMDAT30 RAMDAT29 RAMDAT28 RAMDAT26 RAMDAT25 RAMDAT24 RAMDAT23 RAMDAT22 RAMDAT21 RAMDAT27 RAMDAT20 RAMDAT19 RAMDAT18 RAMDAT17 RAMDAT16 RAMADD2 RAMADD3 RAMADD4 RAMADD0 RAMADD7 RAMADD10 VBG CIN VREFN VCM VREFP CVBSIN VDDA_VFE EJTMS 1.7 0 2.3 0 0 0 3.4 0.2 3.4 0.2 0.2 0 0.2 0.2 3.4 0.2 0.2 0 0.2 3.4 0 3.4 3.4 3.3 3.3 1.6 1.7 0.4 0.2 0.2 0.2 0.2 3.4 0 0.2 0.2 0.2 0.2 0.2 0.3 0 0.3 3.4 1.6 0 0.1 0 0.2 3.4 0.2 0.2 0 0.2 0.2 3.4 0.2 0.2 0 0.2 0 3.4 0.2 3.4 0.2 0.2 0 0.2 0.2 3.4 0.2 0.2 0 0.2 3.4 0 3.4 3.4 3.3 3.4 1.6 1.7 0.4 0.2 0.2 0.2 0.2 3.4 0 0.2 0.2 0.2 0.2 0.2 0.3 0 0.3 3.4 1.6 0 0.1 0 0.2 3.4 0.2 0.2 0 0.2 0.2 3.4 0.2 0.2 0 0.2 0 A 1/6 A 1/6 AV ENCODER BLOCK 2/6 A 5/6 A 6/6 A 1 DVD/HD MPEG PCB ASSY (DVR-RT500-S : A2D309AB10) (DVR-RT300-S : A2D311AB10) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 33 5 6 7 8 5 6 7 8 C D F A B E C4165 0.001 B C4123 0.1 F C4125 0.01 B C4107 0.001 B C4113 0.1 F C4118 0.1 F C4121 0.01 B C4114 0.1 F C4116 0.1 F C4120 0.001 B C4139 0.001 B C4135 0.1 F C4140 0.1 F C4141 0.1 F C4122 0.01 B C4119 0.001 B C4110 0.1 F C4106 0.01 B C4109 0.001 B C4105 0.1 F C4115 22P CH C4142 0.01 B C4138 0.1 F C4158 0.1 F C4161 0.1 F C4144 0.01 B C4143 0.1 F C4117 0.1 F B4004 HCB2012K -600T25 B4005 HCB2012K -600T25 R4108 4.7K R41044.7K R4106 4.7K R4097 4.7K R4044 100 R4105 4.7K R4101 33 R4102 33 R4098 33 R5719 10K R4124 1K R4123 1K R4103 33 IC4009 ZR35100 MPEG ENCODER 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 100 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 C4145 47 6.3V V-S C4128 47 6.3V V-S I55_RESET SBCLK SBDAT VID0 VID1 VID2 VID3 VID4 VID5 VID6 VID7 SBVALID I55_RX0 I55_AODAT I55_ABCLK ADC_ADAT I55_AMCLK I55_GPIO0 I55_ALRCLK I55_GPIO2 BS1 BS1 SBREQ I55_TX1 I55_TX0 I55_RX1 I55_RESET 27MHZ_OSC MA11 MA12 MD10 MD11 MD12 MD13 MD14 MD15 MA8 MA9 MD7 MD8 MD6 MD9 MD5 MD4 MD3 MD2 MD1 MD0 MBA1 MBA0 MRAS MCAS MDQM MCS MWE MCLK NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC 0.2 0 1.7 0 0.3 1.7 3.4 0 0 0.3 3.4 1.5 0 3.3 3.3 0 3.4 1.8 3.4 3.4 0 0 0.1 0.1 0 3.4 0.2 0 0.2 0.2 3.3 0.2 3.3 3.4 0.2 0 0.2 0 0.2 0.2 0.2 0.2 3.4 0.1 0.2 0 0 0 0 0 0 0 0 3.4 0 0 0 0 0 1.8 0 3.4 0 0 0 0 0 3.4 0 0 0 0 0 0 0 0 0 0 3.4 3.4 3.4 3.0 VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDP VDDC VDDC VDDC VDDC VDDC VDDC VDDPCLK VDDIP VDDA VDDAMC OSBCLK OSBVALID OSBDAT OSBREQ AODAT AIDAT ABCLK ALRCLK AMCLK GPAIO GNDAMC VDDP VID0 VID1 VID2 VID3 VID4 VID5 VID6 VID7 GDAT15 GDAT14 GDAT13 GDAT12 GDAT11 GDAT10 GDAT9 GDAT8 GDAT7 GDAT6 GDAT5 GDAT4 GDAT3 GDAT2 GDAT1 GDAT0 GADR8 GADR7 GADR6 GADR5 GADR4 GADR3 GADR2 GADR1 GADR0 GCS0# GCS1# VDDP GIRQ GWS_ACK# GDS# GDIR# GPIO2 GPIO1 GPIO0 DUPTD0 DUPRD0 RESET# GCLK XO PLLCFG GNDA GNDPCLK GNDC GNDC GNDC GNDC GNDC GNDC GNDC 53 52 51 50 GNDP GNDP GNDP GNDP GNDP GNDP GNDP GNDP GNDP GNDP GNDP GNDP RAMDAT14 RAMDAT13 RAMDAT12 RAMDAT11 RAMDAT10 RAMDAT9 RAMDAT8 RAMDAT7 RAMDAT6 RAMDAT5 RAMDAT4 RAMDAT3 RAMDAT2 RAMDAT1 RAMADD1 RAMADD5 RAMADD6 RAMADD8 RAMADD9 RAMADD11 RAMADD12 RAMBA0 RAMBA1 RAMDQM RAMCS# RAMRAS# RAMCAS# RAMWE# PCLK ISOD7 ISOD6 ISOD5 ISOD4 ISOD3 ISOD2 ISOD1 ISOD0 157 156 155 154 ISORDY ISOCLK ISODIR ISOVALTX ISOVALRX ISOSTART VDDP 104 103 GNDP RAMDAT15 102 RAMDAT0 3 2 1 208 TESTMODE IBEXT YIN GNDA_VFE 0 3.4 3.3 0 3.0 1.8 1.7 3.4 0 1.7 1.8 0 0 0 0 0 0.2 0.1 0 0 0 0 0 0 0 0 3.4 0 0 0 0 0 1.8 0 0 NC 3.4 1.5 0 0 1.0 1.7 1.7 0 3.4 3.4 3.4 0 0 2.0 3.4 0 3.4 1.8 1.8 1.0 1.1 1.5 1.6 1.3 1.1 1.3 3.4 A 1/6 6 2 3 4 5 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 34 1 2 3 4 1 2 3 4 C D F A B E 3.4 DVD/HD MPEG PCB ASSY(2/6) A 2/6 IC4002 BR24L16FJ-WE2 EEPROM 1 2 3 4 5 6 7 8 X4001 27MHz DSO751SV 1 2 3 4 IC4001 ZR36750E MPEG 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 1 10 100 11 12 13 14 15 16 17 18 19 2 20 21 22 23 24 25 26 27 28 29 3 30 31 32 33 34 35 36 37 38 39 4 40 41 42 43 44 45 46 47 48 49 5 50 51 52 53 54 55 56 57 58 59 6 60 61 62 63 64 65 66 67 68 69 7 70 71 72 73 74 75 76 77 78 79 8 80 81 82 83 84 85 86 87 88 89 9 90 91 92 93 94 95 96 97 98 99 IC4010 SN74LVC1G125DCKR AMCLK SW 1 2 3 4 5 IC4003 BD5229G RESET 1 2 3 4 5 DIGITAL AUDIO SIGNAL(PB) PLAYBACK COLOR SIGNAL PLAYBACK LUMINANCE SIGNAL COMPONENT SIGNAL(U) COMPONENT SIGNAL(V) JG4058 JG4001 JG4169 JG4172 JG4171 JG4054 JG4063 JG4065 JG4052 JG4170 JG4056 JG4021 JG4057 JG4059 JG4060 JG4061 JG4023 JG4024 JG4025 JG4026 JG4027 JG4028 JG4029 JG4030 JG4031 JG4032 JG4033 JG4034 JG4035 JG4036 JG4037 JG4038 JG4039 JG4040 JG4041 JG4042 JG4043 JG4044 JG4045 JG4046 JG4047 JG4048 JG4049 JG4050 JG4066 JG4022 JG4055 JG4053 JG4084 C4008 0.1 F C4108 0.001 B C4002 0.1 F C4137 0.01 B C4003 0.1 F C4009 0.01 B C4005 0.01 B C4147 0.1 F C4001 0.001 B C4136 0.1 F C4004 0.1 F C4163 0.1 F B4001 FCM2012H -102T04 R4006 1K R4007 1K R4005 1K R4003 4.7K R4127 4.7K R4008 4.7K R4010 4.7K R4012 4.7K R4009 4.7K R4024 47 R4027 4.7K R4029 4.7K R4026 4.7K R4039 4.7K R4040 4.7K R4025 4.7K R4099 4.7K R4058 4.7K R4011 390 +-1% R4100 4.7K R4059 22 R4136 100 R4036 100 R4132 4.7K R4021 100 R4109 22 R4137 47 R4022 4.7K R4016 100 R4015 100 R4129 22 R4130 1K R4121 4.7K R4001 4.7K R4126 10 R4139 10 R4122 4.7K R4028 47 C4007 47 6.3V V-S C4006 47 6.3V V-S SCL SDA I55_TX0 I55_RX0 RAMWE RAMCS RAMRAS RAMBA1 PNVMCE RAMDQM RAMCAS RAMBA0 RAMDAT1 RAMDAT3 RAMDAT5 RAMDAT7 RAMADD0 RAMADD2 RAMADD3 RAMDAT0 RAMDAT2 RAMDAT4 RAMDAT6 RAMADD1 RAMADD4 RAMDAT8 RAMDAT17 RAMDAT19 RAMDAT21 RAMDAT22 RAMDAT23 RAMADD10 RAMDAT16 RAMDAT18 RAMDAT20 RAMDAT25 RAMDAT24 RAMDAT14 RAMDAT12 RAMDAT11 RAMDAT10 RAMDAT31 RAMDAT30 RAMDAT29 RAMDAT28 RAMDAT27 DRVRST RAMDAT26 ATDMARQ RAMDAT25 ATIOW RAMDAT24 ATIOR RAMDAT23 ATIORDY RAMDAT22 ATDMACK RAMDAT21 ATINTRQ RAMDAT20 ATDD2 ATDA1 RAMDAT19 ATDD12 ATDA0 RAMDAT18 ATDD10 ATCS0 ATDD8 RAMDAT17 MHA1 ATDD0 RAMDAT16 MHA3 ATDD1 RAMDAT15 MHD1 ATDD2 MHD3 RAMDAT14 MHD5 ATDD3 RAMDAT13 MHD7 ATDD4 RAMDAT12 ATDD5 RAMDAT11 ATDD6 RAMDAT10 ATDD7 RAMDAT9 ATDD8 RAMDAT8 ATDD9 RAMDAT7 ATDD10 RAMDAT6 ATDD11 RAMDAT5 ATDMARQ ATDD12 RAMDAT4 ATDD3 ATDD13 I55_RESET RAMDAT3 ATDD11 ATDD14 ATDD9 RAMDAT2 MHA0 ATDD15 RAMDAT1 MHA2 ATDA2 RAMDAT0 MHDO ATCS1 MHD2 RAMADD12 MHD4 RAMADD11 MHD6 RAMADD10 RAMADD9 VSC_ON-H RAMADD8 RESET RAMADD7 RAMADD6 RAMADD5 RAMADD4 RAMADD3 ATIOW RAMADD2 ATDD1 RAMADD1 ATDD5 ATDD7 RAMADD0 PCLK RAMCLE RAMDQM RAMWE BOOTSEL0 RAMCAS DRVRST RAMRAS VSC_DATA RAMCS RAMBA0 ADC_ADAT RAMBA1 I55_AODAT PNVMCE RESET ATIOR ATDD0 ATDD4 ATDD6 AMCLK_SEL BOOTSEL1 RESET VSC_CLK SBVALID EXT_RESET I55_AMCLK AMCLK_SEL ATDMACK ATDD13 ATDD15 ATDA2 ATINTRQ ATDD14 ATIORDY ATCS0 ATCS1 ATDA0 ATDA1 FPCCLK VADDIS_AMCLK VADDIS_AMCLK 27MHZ_OSC I55_ALRCLK ABCLKO FPCDOUT MPEG_CS SBDAT I55_ABCLK ICETDI ALRCLKO FPCDIN U_B CVBS C V_R Y_G Y NC NC NC 0 NC NC 20 19 18 17 16 20 19 18 17 16 3 ATDD12 ATDD10 ATDD2 MODRTS MODRD RAMDAT1 RAMDAT3 RAMDAT5 312 313 314 315 316 2 1 RAMDAT7 RAMWE RAMRAS RAMCS RAMBA1 GNDC RAMADD0 RAMADD2 RAMADD3 RAMDAT17 RAMDAT19 RAMDAT21 RAMDAT22 RAMDAT23 PNVMCE MODTD RAMDAT0 RAMDAT2 RAMDAT4 RAMDAT6 RAMDQM RAMCAS GNDC RAMBA0 VDDC RAMADD10 RAMADD1 RAMADD4 RAMDAT16 RAMDAT18 RAMDAT20 RAMDAT25 RAMDAT24 PNVNRB MODDSR MODCTS RAMDAT14 RAMDAT12 RAMDAT11 RAMDAT10 RAMDAT8 16 20 19 18 17 16 82 81 80 79 78 77 VDDP FPCDIN FPCCLK IRRCV FPCSTB AOUT4 ABCLKO NC FPCDOUT ATDA0 ATCS1 ATCS0 ABCLKI ALRCLKO NC VDDP ATDD15 ATIORDY ATDA2 ATDA1 ALRCLKI AMCLK VDDP GNDC VDDC VDDP VDDP VDDC GNDC VDDP NC VDDP ATDD13 ATDD14 ATDMACK ATINTRQ GNDDAC-D VREF RSET SERADC2 TESTMODE SPICLK BOOTSEL2 BOOTSEL1 PLLSEL HCS1 HCS HRD HACK1 ATDD6 ATDD4 ATDD0 ATIOR GNDDAC-D GNDDAC-P GPCIO8 AIN0 AIN1 SERADC0 XO SPIDATO GPCIO19 GPCIO18 BOOTSEL0 PWM HIRQ1 HIRQ HWR HACK ATDD7 ATDD5 ATDD1 ATIOW GNDDAC-D GPCIO7 I2CDAT SERADC1 GCLKA RESET SPIDATI GPAIO0 GPCIO17 HD6 HD4 HD2 HD0 HA2 HA0 ATDD9 ATDD11 ATDD3 ATDMARQ I2CCLK VDDADC GNDADC GCLKP VDDA GNDA GNDA HD7 HD5 HD3 HD1 HA3 HA1 ATDD8 9 8 7 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 6 9 8 7 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 6 20 19 18 17 16 15 14 9 8 7 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 6 9 8 7 5 4 3 2 1 10 6 13 12 11 14 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 20 15 9 8 7 5 4 3 2 1 19 18 17 16 15 14 13 12 11 10 6 9 8 7 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 6 9 8 7 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 6 Y W H G F E D C B A ICETDI SBDAT SBSOS SBVALID VDDD VDDD VDDD GNDDAC-B VDDIP DAC_BU DAC_RV DAC_GY VDDAAM DAC_CVBS DAC_Y GNDAAM MODRI SCL WP A0 SDA VCC GND A2 A1 FROM/TO MEMORY 0 0 0 0 0 0.3 0 3.3 3.1 3.1 3.1 3.1 0 0 0 2.9 0 0 0 0 1.8 1.6 0 3.3 3.3 3.3 3.3 3.3 0 3.0 3.1 0 0 0 0 0 0 0 0 0 0 3.3 1.6 0 3.3 3.3 0 3.3 0 3.1 0 3.1 3.3 0 0 0 3.3 0 3.3 0 1.6 0 0.8 0 3.3 0 0 3.1 3.1 3.3 3.2 0 3.3 3.3 2.9 3.3 0 0 3.3 0 0 0 1.2 0 0 0 3.3 3.3 0.3 0.4 0 0.2 3.2 3.1 2.9 1.4 0 0.4 0.6 0.6 1.3 0.6 0.7 0.6 0.7 1.1 1.2 0.8 0.3 0.2 0.7 0.7 0 3.1 0 1.3 1.8 0.3 0.4 0.5 0.7 0.5 0.5 0.4 0.4 0 0 0 0.3 0.2 0.3 0.3 0.3 0 0 3.3 3.2 3.2 3.3 NC 0 1.8 3.3 4.9 3.3 1.8 0 3.3 0 1.5 1.6 3.3 0 4.9 3.2 3.3 1.4 NC 3.3 1.3 NC 1.4 0 1.6 0 3.3 3.3 0.8 3.3 NC 1.4 1.4 1.6 0 3.3 0 3.3 3.3 3.3 0 GND VCC FROM/TO ATAPI 3.3 3.3 VOUT VDD VSS NC CT 3.1 0 NC 0.2 0.2 1.5 0 3.4 1.7 A 2/6 MPEG BLOCK 4/6 A 3/6 A 8 7 9 10 11 12 13 DVD/HD MPEG PCB ASSY (DVR-RT500-S : A2D309AB10) (DVR-RT300-S : A2D311AB10) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 35 5 6 7 8 5 6 7 8 C D F A B E A 2/6 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 CP4007 A2001WR2-7P 1 2 3 4 5 6 7 JG4117 JG4096 JG4097 JG4088 JG4114 JG4115 JG4068 JG4069 JG4070 JG4174 JG4173 JG4064 JG4074 JG4109 JG4108 JG4107 JG4106 JG4105 JG4104 JG4103 JG4102 JG4101 JG4100 JG4099 JG4129 JG4128 JG4127 JG4017 JG4125 JG4078 JG4079 JG4165 JG4051 JG4067 JG4071 JG4072 JG4073 JG4075 JG4076 JG4062 JG4077 JG4089 JG4002 JG4003 JG4004 JG4005 JG4006 JG4007 JG4008 JG4009 JG4010 JG4011 JG4012 JG4013 JG4016 JG4080 JG4081 JG4082 JG4083 C4130 0.001 B C4012 0.01 B C4039 0.1 F C4037 0.1 F C4035 0.1 F C4033 0.1 F C4031 0.1 F C4029 0.01 B C4027 0.01 B C4025 0.001 B C4023 0.001 B C4038 0.1 F C4042 0.01 B C4044 0.001 B C4045 0.001 B C4046 0.001 B C4043 0.01 B C4041 0.01 B C4040 0.1 F C4036 0.1 F C4034 0.1 F C4032 0.1 F C4030 0.1 F C4028 0.1 F C4026 0.1 F C4024 0.1 F C4022 0.1 F C4021 0.1 F C4020 0.1 F C4018 0.1 F C4017 0.1 F C4015 0.01 B C4134 0.001 B C4129 0.001 B C4014 0.1 F C4013 0.1 F C4164 0.1 F C4162 0.1 F B4006 FCM2012H -102T04 B4007 FCM2012H-102T04 B4008 FCM2012H -102T04 R4133 4.7K R4115 4.7K R4030 4.7K R4033 1K R4031 1K R4041 1K R4049 4.7K R4048 4.7K R4023 4.7K R4046 4.7K R4014 100 R4134 10 R4116 4.7K R4135 4.7K R4113 22 R4032 4.7K R4020 4.7K R4114 4.7K R4118 4.7K R4119 4.7K R4120 4.7K R414010 R4131 100 R4034 4.7K R4047 100 C4011 47 6.3V V-S C4019 10 16V V-S C4016 10 16V V-S C4047 10 16V V-S C4010 47 6.3V V-S I55_GPIO2 DUPTD VADDIS_INT PCLK RAMCLE RAMADD9 RAMADD7 RAMADD5 RAMDAT9 RAMADD8 RAMADD6 RAMDAT31 RAMDAT29 RAMDAT28 RAMDAT26 RAMDAT15 RAMDAT13 RAMADD11 RAMDAT30 RAMDAT27 RAMADD12 GND +3.3V +1.8V D5V MPEG_CS FPCDOUT FPCCLK FPCDIN VSC_ON-H VSC_DATA VSC_CLK VIDEO_IN_SEL VADDIS_INT VIDHS ASP1 ASP2 ICETCK ICETDO P-H/I-L U_B V_R Y_G CVBS ICETDI Y C ICETMS EXT_RESET SPDIF MUTE SCL DUPRD SDA MUTE VIDVLD VIDEO_IN_SEL VIDHS VIDVS P-H/I-L VID5 VID6 VID7 VIDCLK AOUT0 ABCLKO ALRCLKO SCL VID1 SDA VID2 VID3 VADDIS_AMCLK VID4 ADC_ADAT VID6 VID5 VID7 VID0 ASP1 VIDVLD VID3 VIDHS VID2 VIDVS VID4 VIDCLK VID0 EXT_RESET VID1 VID2 VID3 BOOTSEL0 VID4 VID5 ASP2 BOOTSEL1 VID6 DUPTD VID7 I55_GPIO0 DUPRD I55_GPIO2 SBVALID SBREQ SBCLK SBDAT 27MHZ_OSC I55_RESET I55_AODAT I55_ABCLK I55_ALRCLK I55_AMCLK I55_TX0 I55_RX0 MHDO MHD1 MHD2 MHD3 MHD4 MHD5 MHD6 MHD7 MHA0 MHA1 MHA2 MHA3 VID1 I55_GPIO0 VID0 VIDCLK AOUT0 SPDIF ICETMS SBCLK SBREQ NC NC 3.3 NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC 156 157 158 159 160 162 161 NVMCE NVMCE1 NVMCLE NVMALE VIDO1 VIDO0 VCLKX2 240 239 238 GNDP VDDC RAMADD9 RAMADD7 RAMADD5 RAMDAT31 RAMDAT29 RAMDAT28 RAMDAT26 GPCIO20 GPCIO10 GPCIO9 MODDCD MODDTR RAMDAT15 RAMDAT13 VDDP GNDP RAMDAT9 VDDP PCLK VDDP RAMADD11 RAMADD8 RAMADD6 VDDP RAMDAT30 RAMDAT27 DUPTD GPCIO11 GPCIO12 HSYNC VCLK 237 236 235 20 19 18 17 16 15 14 13 12 11 10 GNDP GNDP VDDP VDDP GNDP GNDP GNDP VDDP GNDP VDDP GNDP GNDP DUPRD GPCIO14 GPCIO13 VIDIVALID VIDIHS VIDIVS VSYNC NVMDA4 NVMDA3 VDDP VDDP GPCIO16 GPCIO15 VIDI5 VIDI6 VIDI7 VIDICLK NC NC NVMDA1 NVMDA2 NVMDA6 NVMDA5 VIDI1 VIDI2 VIDI3 VIDI4 NC VDDP NVMDA7 NVMDA0 NVMWP NVMRB VIDO6 VIDO5 VIDO7 VIDI0 VDDP GNDP GNDP GNDP GNDP GNDC NVMRB1 NVMCD NVMWE NVMRE GNDP GNDP GNDP GNDP VIDO3 VIDO2 VIDO4 VDDC GNDC GNDP GNDP GNDP GNDP VDDC 20 19 18 17 16 20 19 18 17 16 20 19 18 17 16 10 12 11 20 19 18 17 16 9 10 12 11 20 19 18 17 16 9 10 12 11 20 19 18 17 16 9 10 12 11 20 19 18 17 16 9 20 19 18 17 COSYNC VDDP VDDP GNDP GNDP GNDP GNDP EJTDI EJTRST EJTMS EJTDO S/PDIF AOUT1 AOUT0 NC GPCIO6 PLLCFGA PLLCFGP EJTCK AOUT2 AOUT3 9 8 7 5 4 3 2 1 13 12 11 10 6 9 8 7 5 4 3 2 1 6 1 9 8 7 5 4 3 2 20 19 18 17 16 15 14 13 12 11 10 6 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 V U T R P N M L K J NC RAMADD12 ICETMS ICETDO 234 ICETCK SBCLK SBREQ DAC_C VDDIP RAMCLE 0 0 4.8 0 1.8 0 0 0 0 0 0 0 0 0 1.8 0 0 0 0 0 4.9 0 3.3 0.8 0 0 0 0 0 0 0 0.5 0.8 0 0 0 0 0 0 0 1.7 1.7 0.5 0.7 0 3.3 0 0 3.3 3.3 0 3.3 0 0 3.3 3.3 4.9 0 0 0 3.3 0 3.3 0 3.3 0 0 0 3.3 0 0 4.9 1.6 0 0 0 1.8 3.3 0.1 0.4 0.3 0.3 0.3 0.2 0.3 0 0 5.0 0 3.3 0.3 0.3 3.3 0 0.5 3.3 1.5 3.3 0 1.8 0.4 3.3 0.2 3.3 0.2 3.3 0 1.4 3.3 0 0 3.3 0 3.2 3.3 4.9 0 0 0 0 NC 1.9 0 1.6 0 3.3 0 3.3 3.3 3.3 0 0 0 0 3.3 3.0 0 0 0 FROM/TO AV I/O GND BOOT0 BOOT1 TD RD 5V RESET FROM/TO AUDIO FROM/TO AV ENCODER 6/6 A 5/6 A 1/6 A 14 15 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 36 1 2 3 4 1 2 3 4 C D F A B E 3.5 DVD/HD MPEG PCB ASSY(3/6) A 3/6 C4053 0.1 F C4057 0.1 F C4051 0.1 F C4050 0.1 F C4058 0.1 F C4052 0.1 F C4049 0.1 F C4056 0.1 F C4055 0.1 F C4048 0.1 F C4153 0.01 B C4155 0.01 B C4154 0.001 B C4156 0.001 B IC4005 MT48LC8M16A2P-7E SDRAM 1 10 11 12 13 14 15 16 17 18 19 2 20 21 22 23 24 25 26 27 28 29 3 30 31 32 33 34 35 36 37 38 39 4 40 41 42 43 44 45 46 47 48 49 5 50 51 52 53 54 6 7 8 9 IC4004 MT48LC8M16A2P-7E SDRAM 1 10 11 12 13 14 15 16 17 18 19 2 20 21 22 23 24 25 26 27 28 29 3 30 31 32 33 34 35 36 37 38 39 4 40 41 42 43 44 45 46 47 48 49 5 50 51 52 53 54 6 7 8 9 C4054 47 6.3V V-S RAMDAT0 RAMDAT15 RAMDAT1 RAMDAT14 RAMDAT2 RAMDAT13 RAMDAT3 RAMDAT12 RAMDAT4 RAMDAT11 RAMDAT5 RAMDAT10 RAMDAT6 RAMDAT9 RAMDAT7 RAMDAT8 RAMDQM RAMWE RAMDQM RAMCAS PCLK RAMRAS RAMCLE RAMCS RAMADD12 RAMBA0 RAMADD11 RAMBA1 RAMADD9 RAMADD10 RAMADD8 RAMADD0 RAMADD7 RAMADD1 RAMADD6 RAMDAT31 RAMADD2 RAMADD5 RAMDAT30 RAMADD3 RAMADD4 RAMDAT29 RAMDAT28 RAMDAT27 RAMDAT26 RAMDAT25 RAMDAT24 RAMDAT23 RAMDAT22 RAMDAT21 RAMDAT20 RAMDAT19 RAMDAT18 RAMDAT17 RAMDAT16 RAMDAT15 RAMDAT14 RAMDAT13 RAMDAT12 RAMDAT16 RAMDAT31 RAMDAT11 RAMDAT10 RAMDAT9 RAMDAT17 RAMDAT30 RAMDAT8 RAMDAT7 RAMDAT18 RAMDAT29 RAMDAT6 RAMDAT5 RAMDAT4 RAMDAT19 RAMDAT28 RAMDAT3 RAMDAT20 RAMDAT27 RAMDAT2 RAMDAT1 RAMDAT0 RAMDAT21 RAMDAT26 RAMADD12 RAMDAT22 RAMDAT25 RAMADD11 RAMADD10 RAMADD9 RAMDAT23 RAMDAT24 RAMADD8 RAMADD7 RAMADD6 RAMDQM RAMADD5 RAMADD4 RAMWE RAMDQM RAMADD3 RAMCAS PCLK RAMADD2 RAMADD1 RAMRAS RAMCLE RAMADD0 RAMCS RAMADD12 PCLK RAMCLE RAMBA0 RAMADD11 RAMDQM RAMBA1 RAMADD9 RAMWE RAMCAS RAMADD10 RAMADD8 RAMRAS RAMADD0 RAMADD7 RAMCS RAMBA0 RAMADD1 RAMADD6 RAMBA1 RAMADD2 RAMADD5 PNVMCE RESET RAMADD3 RAMADD4 PNVMR_B +3.3V GND (128Mbit) (128Mbit) FROM/TO MPEG (BA0) (BA1) (BA0) (BA1) NC A11 CKE DQ10 VSSQ VCCQ DQ13 DQ14 DQ15 VSS VSSQ DQ12 DQ11 DQ9 VCCQ DQ8 VSS NC UDQM CLK A9 A8 A7 A6 A5 A4 VSS VCC A3 A2 A1 A0 A10 A12 A13 CS RAS CAS WE LDQM VCC DQ7 VSSQ DQ6 DQ5 VCCQ DQ4 DQ3 VSSQ DQ2 DQ1 VCCQ DQ0 VCC NC A11 CKE DQ10 VSSQ VCCQ DQ13 DQ14 DQ15 VSS VSSQ DQ12 DQ11 DQ9 VCCQ DQ8 VSS NC UDQM CLK A9 A8 A7 A6 A5 A4 VSS VCC A3 A2 A1 A0 A10 A12 A13 CS RAS CAS WE LDQM VCC DQ7 VSSQ DQ6 DQ5 VCCQ DQ4 DQ3 VSSQ DQ2 DQ1 VCCQ DQ0 VCC A12 A12 0 0.5 0 0.6 0.4 3.3 0.5 0.6 0 0.7 0.5 3.3 0.7 0 NC 0 1.5 3.3 0 0 0 0.2 0 0.1 0.1 0.1 0 3.3 0.1 0.1 0.1 0.2 0.8 1.4 1.3 3.3 3.3 3.3 3.3 0 3.3 0.3 0 0.2 0.1 3.3 0.1 0.1 0 0.1 0.2 3.3 0.1 3.3 0 3.3 0.5 0.5 0.5 0.5 0.5 0.1 0.2 0.1 3.3 1.5 0 NC 0 0.2 3.3 0.1 0.1 0 0.1 0.1 3.3 0.1 0.1 0 0.7 0 0.6 0.6 0.3 0.4 0.4 1.4 1.4 2.8 3.0 3.1 3.1 0 3.3 0 0 0 0 3.3 0 0 0 0 0 3.3 0 3.3 0 0 FROM/TO AUDIO A 3/6 MEMORY BLOCK 2/6 A 5/6 A 16 DVD/HD MPEG PCB ASSY (DVR-RT500-S : A2D309AB10) (DVR-RT300-S : A2D311AB10) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 37 5 6 7 8 5 6 7 8 C D F A B E A 3/6 NR4007 4D03WGJ0470T5E 47 NR4003 4D03WGJ0470T5E 47 NR4002 4D03WGJ0470T5E 47 NR4005 4D03WGJ0470T5E 47 NR4001 4D03WGJ0470T5E 47 NR4004 4D03WGJ0470T5E 47 NR4008 4D03WGJ0470T5E 47 NR4006 4D03WGJ0470T5E 47 IC4006 LH28F640BFHE-PTTL80 64Mbit FLASH 1 10 11 12 13 14 15 16 17 18 19 2 20 21 22 23 24 25 26 27 28 29 3 30 31 32 33 34 35 36 37 38 39 4 40 41 42 43 44 45 46 47 48 5 6 7 8 9 C4061 0.1 F C4060 0.1 F R4062 51 R4055 51 R4056 51 R4057 51 R4061 51 R4060 51 R4063 51 R4052 51 C4059 47 6.3V V-S RAMADD1 FRAMADD1 RAMADD0 FRAMADD0 RAMADD10 FRAMADD10 RAMBA1 FRAMBA1 RAMBA0 FRAMBA0 RAMDAT7 FRAMDAT7 RAMDAT6 FRAMDAT6 RAMDAT5 FRAMDAT5 RAMDAT9 FRAMDAT9 RAMDAT8 FRAMDAT8 RAMADD11 FRAMADD11 RAMADD9 FRAMADD9 RAMADD8 FRAMADD8 RAMADD7 FRAMADD7 RAMADD6 FRAMADD6 RAMADD5 FRAMADD5 RAMDAT16 FRAMDAT16 RAMDAT17 FRAMDAT17 RAMDAT18 FRAMDAT18 RAMDAT19 FRAMDAT19 RAMDAT20 FRAMDAT20 RAMDAT21 FRAMDAT21 RAMDAT22 FRAMDAT22 RAMDAT23 FRAMDAT23 RAMDAT24 FRAMDAT24 RAMDAT25 FRAMDAT25 RAMDAT26 FRAMDAT26 RAMDAT27 FRAMDAT27 RAMDAT28 FRAMDAT28 RAMDAT29 FRAMDAT29 RAMDAT30 FRAMDAT30 RAMDAT31 FRAMDAT31 FRAMADD1 RAMADD2 FRAMADD0 FRAMADD10 FRAMBA1 FRAMDAT16 FRAMBA0 FRAMDAT17 FRAMDAT7 FRAMDAT18 FRAMDAT6 FRAMDAT19 FRAMDAT5 FRAMDAT20 RAMDAT12 FRAMDAT21 RAMDAT3 FRAMDAT22 RAMADD4 FRAMDAT23 RESET FRAMDAT24 FRAMDAT25 RAMDAT4 FRAMDAT26 RAMDAT11 FRAMDAT27 RAMDAT10 FRAMDAT28 FRAMDAT9 FRAMDAT29 FRAMDAT8 FRAMDAT30 FRAMADD11 FRAMDAT31 FRAMADD9 RAMADD3 FRAMADD8 FRAMADD7 PNVMCE FRAMADD6 FRAMADD5 A16 VCCO GND DQ15/A_1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE GND CE A0 A3 A1 A2 A4 A5 A6 A7 A17 A18 A19 WP VPP RP WE A20 A21 A8 A9 A10 A11 A12 A13 A14 A15 0.1 3.3 0 0.2 0.2 0.1 0.2 0.2 0.2 0.2 0.2 3.3 3.3 3.3 0.1 0.2 0.2 0.2 0.2 0.2 0.2 0 3.3 0.5 0.5 0.6 0.5 0.1 0.2 0.4 0.4 0.3 0.5 0 3.3 3.3 3.3 0.6 0.5 0.4 0.6 0.5 0.7 1.4 1.5 0.4 0.4 0.3 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 38 1 2 3 4 1 2 3 4 C D F A B E 3.6 DVD/HD MPEG PCB ASSY(4/6) A 4/6 CP4001 04_6274_040_000_800 ATAPI FFC 1 10 11 12 13 14 15 16 17 18 19 2 20 21 22 23 24 25 26 27 28 29 3 30 31 32 33 34 35 36 37 38 39 4 40 5 6 7 8 9 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 21 23 25 27 29 31 33 35 36 37 38 NC NC NC NC NC DRVRST GND ATDD7 ATDD8 ATDD6 ATDD9 ATDD5 ATDD10 ATDD4 ATDD11 ATDD3 ATDD12 ATDD2 ATDD13 ATDD1 ATDD14 ATDD0 ATDD15 GND ATDMARQ GND GND GND ATIORDY ATDMACK GND ATINTRQ ATDA1 ATDA0 ATDA2 ATCS0 ATCS1 GND ATDIOW ATDIOR NC NC NC GND A 4/6 ATAPI BLOCK DRIVE ASSY R7R DVD/HD MPEG PCB ASSY (DVR-RT500-S : A2D309AB10) (DVR-RT300-S : A2D311AB10) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 39 5 6 7 8 5 6 7 8 C D F A B E A 4/6 R4095 33 R4066 4.7K R4067 10K R4070 33 R4072 33 R4074 33 R4076 33 R4078 33 R4080 33 R4082 33 R4069 33 R4071 33 R4073 33 R4075 33 R4077 33 R4079 33 R4081 33 R4083 33 R4068 33 R4094 22 R4093 82 R4085 22 R4092 22 R4084 82 R4091 33 R4090 33 R4088 33 R4089 33 R4087 33 R4086 82 R4064 5.6K R4117 10K R4110 10K DRVRST ATDD7 ATDD8 ATDD6 ATDD9 ATDD5 ATDD10 ATDD4 ATDD11 ATDD3 ATDD12 DRVRST ATDMARQ ATDD2 ATIOW ATDD13 ATIOR ATIORDY ATDD1 ATDMACK ATDD14 ATINTRQ ATDA1 ATDD0 ATDA0 ATDD15 ATCS0 ATDD0 ATDD1 ATDD2 ATDD3 ATDMARQ ATDD4 ATDD5 ATDD6 ATIOW ATDD7 ATDD8 ATDD9 ATIOR ATDD10 ATDD11 ATDD12 ATIORDY ATDD13 ATDD14 ATDD15 ATDMACK ATDA2 ATCS1 ATINTRQ ATDA1 ATDA0 ATDA2 ATCS0 ATCS1 D5V GND 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 21 23 25 27 29 31 33 35 36 37 38 FROM/TO MPEG FROM/TO AV I/O 6/6 A 2/6 A www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 40 1 2 3 4 1 2 3 4 C D F A B E 3.7 DVD/HD MPEG PCB ASSY(5/6) A 5/6 AUDIO SIGNAL AUDIO SIGNAL(PB) TUNER AUDIO SIGNAL IC7301 WM8776SEFT/R AUDIO CODEC 1 10 11 12 13 14 15 16 17 18 19 2 20 21 22 23 24 25 26 27 28 29 3 30 31 32 33 34 35 36 37 38 39 4 40 41 42 43 44 45 46 47 48 5 6 7 8 9 Q7301 DTC124EKA MUTE SW CAUTION: DIGITAL TRANSISTOR C7324 0.1 B C7305 0.1 B C7309 0.1 B C7327 1 B C7328 0.1 B C7310 0.1 B C7326 1 B C7334 0.1 B C7331 0.1 B R7311 10K R7306 4.7K R7301 4.7K R7362 10 R7358 10 C7325 10 16V V-S C7306 10 16V V-S C7332 10 16V V-S C7329 10 16V V-S C7322 10 16V V-S C7336 10 16V V-S AOUT0 ABCLKO ADC_ADAT ALRCLKO I55_ALRCLK I55_AMCLK I55_ABCLK VADDIS_AMCLK ADC_ADAT I55_ALRCLK I55_ABCLK I55_AMCLK ADC_ADAT SDA SDA SCL VADDIS_AMCLK SCL ABCLKO AOUT0 ALRCLKO AIN3L AIN1L AIN1R AIN2L AIN3R AIN4L AIN4R AIN5L AIN5R AINOPL AINVGL AINOPR AINVGR AGND 37 AVDD ADCREFP ADCREFGND VMIDADC AUXL AUXR DACREFP DACREFN VMIDDAC VOUTR VOUTL NC HPOUTR HPVDD HPGND HPOUTL CL DI CE MODE DVDD DGND 13 ADCLRC DOUT ADCMCLK ADCBCLK ZFLAGL DIN DACLRC ZFLAGR DACBCLK DACMCLK AIN2R 48 24 NC NC NC NC NC NC FROM/TO AV ENCODER FROM/TO MPEG 3.4 0 0 3.4 0 1.7 0.3 0 3.4 3.4 2.6 0 5.0 2.5 0.1 0.3 2.5 2.5 2.5 0 5.2 2.6 2.6 2.6 0 2.6 5.2 0 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 2.6 1.7 1.8 1.1 1.7 0 0 1.7 1.5 1.1 A 5/6 AUDIO BLOCK 1/6 A 2/6 A 17 19 22 21 18 20 DVD/HD MPEG PCB ASSY (DVR-RT500-S : A2D309AB10) (DVR-RT300-S : A2D311AB10) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 41 5 6 7 8 5 6 7 8 C D F A B E A 5/6 C7341 1 B C7346 1 B C7347 1 B C7350 1 B C7351 1 B C7352 1 B C7353 1 B C7354 1 B C7338 0.1 B C7337 0.1 B B7301 FCM2012H-102T04 R7318 100K R7319 100K R7320 100K R7321 100K R7322 100K R7323 100K R7326 82K R7327 82K R7315 47K R7312 47K ZERO AUDIO_IN_L_1 AUDIO_IN_R_1 AUDIO_IN_L_2 AUDIO_IN_R_2 TU_AUDIO_L TU_AUDIO_R BS_AUDIO_L BS_AUDIO_R DAC_R DAC_L GND +3.3V A5V GND FROM/TO AV I/O 6/6 A 6/6 A 24 23 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 42 1 2 3 4 1 2 3 4 C D F A B E 3.8 DVD/HD MPEG PCB ASSY(6/6) A 6/6 L7306 1uH L7303 1uH L7302 1uH L7305 1uH L7309 6.8uH L7307 6.8uH L7308 6.8uH TUNER VIDEO SIGNAL LUMINANCE SIGNAL COLOR SIGNAL IC7302 MM1501XNRE TU/EXT VIDEO SW IC 1 2 3 4 5 6 AUDIO SIGNAL AUDIO SIGNAL(PB) TUNER AUDIO SIGNAL DIGITAL AUDIO SIGNAL(PB) PLAYBACK COLOR SIGNAL C7319 12P CH C7317 150P CH C7303 150P CH C7313 150P CH C7302 150P CH C7312 150P CH C7307 12P CH C7308 12P CH C7316 150P CH C7318 12P CH C7321 150P CH C7366 82P CH C7368 0.1 F C7323 150P CH C7363 56P CH C7360 0.47 B C7364 82P CH C7358 0.47 B C7361 56P CH C7365 82P CH C7362 56P CH C7359 0.47 B C7371 18P CH C7372 18P CH C7373 18P CH R7314 75 +-1% R7307 75 +-1% R7304 75 +-1% R7302 75 +-1% R7303 75 +-1% R7313 75 +-1% R7342 100 R7339 100K R7336 100 R7335 100 R7340 100 R7337 100K R7332 100 R7331 100 R7341 100 R7338 100K R7334 100 R7333 100 C7367 47 6.3V V-S C7370 47 6.3V V-S C7369 47 6.3V V-S ZERO DAC_L DAC_R BS_AUDIO_L BS_AUDIO_R TU_AUDIO_L TU_AUDIO_R AUDIO_IN_L_2 AUDIO_IN_R_2 AUDIO_IN_L_1 AUDIO_IN_R_1 GND GND +3.3V A5V GND YIN CIN CVBSIN GND +3.3V +1.8V D5V V_R U_B VIDEO_IN_SEL U_B V_R Y_G CVBS Y C MUTE Y_G SPDIF EXT_RESET VSC_ON-H VSC_DATA VSC_CLK VADDIS_INT ASP1 ASP2 P-H/I-L SDA SCL CVBS FPCDOUT FPCCLK FPCDIN MPEG_CS +3.3V D5V +1.8V GND Y GND D5V C +3.3V GND FROM/TO AUDIO FROM/TO ATAPI FROM/TO MEMORY FROM/TO AV ENCODER FROM/TO MPEG Vcc BAIAS BUFFER 0 2.6 5.2 3.0 0 3.0 5/6 A 1/6 A 2/6 A 4/6 A 3/6 A 27 28 29 30 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 43 5 6 7 8 5 6 7 8 C D F A B E A 6/6 04_6232_120_103_800 1 10 11 12 13 14 15 16 17 18 19 2 20 3 4 5 6 7 8 9 CP7301 CP7302 CP7303 CP7304 04_6232_120_103_800 1 10 11 12 13 14 15 16 17 18 19 2 20 3 4 5 6 7 8 9 04_6232_118_103_800 1 10 11 12 13 14 15 16 17 18 2 3 4 5 6 7 8 9 A2001WV2-10P 1 10 2 3 4 5 6 7 8 9 PLAYBACK LUMINANCE SIGNAL COMPONENT SIGNAL(U) COMPONENT SIGNAL(V) C7348 100P CH C7342 100P CH C7343 100P CH C7344 100P CH C7374 100P CH C7339 0.1 F C7330 0.001 B C7340 0.1 F C7349 0.1 F C7345 100P CH C7376 100P CH C7375 100P CH B7305 HCB2012K-600T25 B7304 HCB2012K-600T25 B7306 HCB2012K-600T25 B7307 HCB2012K-600T25 R7324 4.7K R7325 4.7K BS_AUDIO_L BS_AUDIO_R TU_AUDIO_L TU_AUDIO_R AUDIO_IN_L_2 AUDIO_IN_R_2 AUDIO_IN_L_1 AUDIO_IN_R_1 Y_VIDEO_IN C_VIDEO_IN TU_VIDE0 DAC_L DAC_R COMPOSITE_IN ZERO MUTE ASP1 ASP2 P-H/I-L SPDIF VADDIS_INT SDA SCL EXT_RESET MPEG_CS FPCCLK FPCDIN FPCDOUT VSC_ON-H VSC_DATA VSC_CLK +1.8V +3.3V D5V A5V NC NC NC NC GND GND GND MPEG5V +3.3V +1.8V GND GND GND GND GND GND REAR AUDIO L REAR AUDIO R FRONT AUDIO L FRONT AUDIO R GND TU AUDIO L TU AUDIO R GND GND GND BS/TU V IN GND V/R_OUT GND U/B_OUT GND GND Y/G_OUT GND GND Y_OUT CVBS_OUT C_OUT GND AUDIO_L_OUT AUDIO_R_OUT GND GND CVBS_IN GND MUTE ZERO ASP2 ASP1 P-H/I-L IIC_DATA IIC_CLK RESET VSC CLK VSC DATA VSC ON-H GND MPEG CLK MPEG DATA IN MPEG DATA OUT MPEG CS SPDIF F/R C IN F/R Y IN VCR AUDIO L VCR AUDIO R VADDIS INT +1.8V +3.3V NC(GND) NC(GND) A 6/6 AV IN/OUT BLOCK CP8301 B 7/7 CP8302 B 7/7 CP8303 B 7/7 CP1703 B 4/7 32 34 33 31 26 25 DVD/HD MPEG PCB ASSY (DVR-RT500-S : A2D309AB10) (DVR-RT300-S : A2D311AB10) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 44 1 2 3 4 1 2 3 4 C D F A B E 3.9 VCR MT PCB ASSY(1/7) B 1/7 Q103 DTA124EKA SW CP101 TOC-C09X-A1 1 2 3 4 5 6 7 8 9 CP102 CP103 IMSA-9604S-06C 1 2 3 4 5 6 B2013H02-2P 1 2 C115 33 10V KA C105 22 16V KA C103 220 6.3V KA C112 220 6.3V KA C104 220 6.3V YK C163 47 6.3V KA C120 1 50V KA L101 1626009 COIL,BIAS OSC 1 2 3 4 5 6 C109 0.1 B C101 0.022 100V MMTS C158 0.1 B C118 0.01 B C116 0.1 F C169 0.047 F C165 0.047 F C166 0.068 B C122 0.0012 B C154 0.1 B C107 0.015 B C106 0.01 B C156 0.1 F C121 0.0027 B C162 0.1 B C114 0.1 B R136 22K R146 12K R138 22K1/4W R105 10K R101 560 1/4W R102 4.7K R103 4.7K R110 8.2K R111 8.2K R112 330K R114 18K R107 3.3K R106 6.8K R108 22K R139 12K R142 820 R113 220 C119 10 25V KA C110 47 6.3V KA Q104 KTC3203_Y BIAS OSC Q101 KTC3875S_Y_RTK AUDIO PB SW Q102 KTC3875S_Y_RTK AUDIO PB SW W806 W809 Q105 KTA1266 BIAS CTL L102 100uH 0305 L107 22uH 0305 IC101 LA71206M-MPB Y/C/AUDIO/CCD/HEAD AMP IC 1 2 3 4 5 53 54 55 56 57 58 59 6 60 61 62 63 64 65 66 67 68 69 7 70 71 72 73 74 75 76 77 78 79 8 80 L109 100uH COMP H.SW ENV.DET Y/C_CS H.AMP_SW C.ROTARY Y/C_DATA Y/C_CLK P.CON+5V GND FSC NORMAL_A_IN NORMAL_A_OUT HF1 HF_COM HF2 GND P.CON+5V NORMAL_A_IN P.CON+5V V.REC_ST-H CTL+ CTL- GND HOT FROM/TO HI-FI/DEMODULATOR AE HEAD(-) AE HEAD(+) AUDIO REC AUDIO PB HF COM SP COM 0.2 5.0 5.0 0.2 0.2 5.0 5.0 1.9 3.9 0.7 0.7 0.7 4.9 0 0 4.9 4.9 4.9 4.9 0 0 0.7 0.7 0 0 0 FROM/TO REGULATOR FROM/TO CYL FE HEAD(GND) FE HEAD(HOT) TO FE HEAD FROM/TO HEAD AUDIO CONTROL CTL- CTL+ EP/LP-CH2 (L) EP/LP-CH1 (R) SP-CH2 (L) SP-CH1 (R) EP/LP COM HF1 (R) HF2 (L) 0 + Vref 2.3V SP,LP EQ AMP ALC ALC A-VCC 1 2 3 A-GND HA PRE GND R P P R P P H L H L REC:LPIC1701 IC LM2902DR I0CF0902D IC3001 IC OEC0142B I54F50142B IC3003 IC XC61CN3102SR IE2F031020 NSP IC3099 MEMORY DATA S-24C08AFJA-TB-0 S2D309AE01 * This is NOT SERVICE PART because the Unit does not work properly when replacing this part. Please replace VCR MTB Assy when replacement of this part is required. IC4001 IC ZR36750E ICQM067500 IC4002 MEMORY DATA BR24L16FJ-WE2 S2D309AE02 (for DVR-RT500-S) IC4002 MEMORY DATA BR24L16FJ-WE2 S2D309AE03 (for DVR-RT300-S) IC4003 IC BD5229G I97F052290 IC4004 IC MT48LC8M16A2P-7E IF6J08M167 IC4005 IC MT48LC8M16A2P-7E IF6J08M167 IC4006 MEMORY DATA LH28F640BFHE-PTTL80 S2D309AF01 IC4007 IC HY57V561620CT-7 ICLJ020CT7 IC4008 IC HY57V561620CT-7 ICLJ020CT7 IC4009 IC ZR35100 ICQK051000 IC4010 IC SN74LVC1G125DCKR I5CJ0G1250 IC7301 IC WM8776SEFT/R IFJK087760 IC7302 IC MM1501XNRE I0UF015010 IC8301 IC NJM4580M(TE1) I0QJ045800 IC8302 IC NJM2534V(TE2) I0QF02534V IC8303 IC NJM2534V(TE2) I0QF02534V IC8304 IC NJM2534V(TE2) I0QF02534V IC8305 IC NJM2534V(TE2) I0QF02534V IC8307 IC LA7210 I03S072100 IC8308 IC NJM2246M-TE1 I0QF02246M IC8309 IC NJM2246M-TE1 I0QF02233M Q101 TRANSISTOR,SILICON KTC3875S_Y_RTK TCAA3875SY Q102 TRANSISTOR,SILICON KTC3875S_Y_RTK TCAA3875SY Q103 COMPOUND TRANSISTOR DTA124EKAT146 TPYJC05001 Q104 TRANSISTOR,SILICON KTC3203S_Y TCAT032034 Q105 TRANSISTOR,SILICON KTA1266 TAATA12660 Q106 TRANSISTOR,SILICON KTA1504S_Y_RTK TAAA1504SY Q107 TRANSISTOR,SILICON KTA1504S_Y_RTK TAAA1504SY Q109 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q301 TRANSISTOR,SILICON KTC3198 TAAA1504SY Q302 COMPOUND TRANSISTOR DTA124EKAT146 TNJYJC05001 Q303 TRANSISTOR,SILICON KTC3875S_Y_RTK TCAA3875SY Q651 TRANSISTOR,SILICON KTC3875S_Y_RTK TCAA3875SY Q652 TRANSISTOR,SILICON KTC3875S_Y_RTK TCAA3875SY Q1701 COMPOUND TRANSISTOR DTA143EKAT146TPYJA05001 Q1703 COMPOUND TRANSISTOR DTA124EKAT146TPYJC05001 Q1706 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q1707 COMPOUND TRANSISTOR DTA124EKAT146TPYJA05001 Q1708 TRANSISTOR,SILICON KTB1151 TBA0011510 Q1709 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q1710 TRANSISTOR,SILICON KTC3203 TCAT032034 Q1711 TRANSISTOR,SILICON KTC3203 TCAT032034 Q1712 TRANSISTOR,SILICON KTC3875S TCAA3875SY Q1713 TRANSISTOR,SILICON KTB1151 TBA0011510 Q1716 TRANSISTOR,SILICON KTC3209 TCAT032034 Q1717 COMPOUND TRANSISTOR DTA124EKAT146TNYJC05001 Q1720 TRANSISTOR,SILICON KTC3209 TCAT03209Y Q1721 TRANSISTOR,SILICON KTA1281 TAAT0128Y Q1722 COMPOUND TRANSISTOR DTC124EKAT146TNYJC05001 Q1723 TRANSISTOR,SILICON KTA1271 TAAT012714 Q1724 COMPOUND TRANSISTOR DTC124EKAT146TNYJC05001 Q3001 PHOTO COUPLER RPI-303 2700690 Q3002 PHOTO COUPLER RPI-303 2700690 Q3004 PHOTO COUPLER RPI-352C40N 2700680 Q3005 PHOTO COUPLER RPI-352C40N 2700680 Q3006 PHOTO TRANSISTOR ST-304L 0000M00390 Q3007 COMPOUND TRANSISTOR DTA143EKAT146 TPYJA05001 Q3008 PHOTO TRANSISTOR ST-304L 0000M00390 Q7301 COMPOUND TRANSISTOR KRC103SRTK TNAAC05002 Q8001 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8002 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8003 COMPOUND TRANSISTOR DTC124EKAT146TNYJC05001 Q8004 COMPOUND TRANSISTOR DTA143EKAT146TPYJA05001 Q8005 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8006 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8007 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8008 COMPOUND TRANSISTOR DTC124EKAT146TPYJC05001 Q8009 COMPOUND TRANSISTOR DTC124EKAT146TPYJC05011 Q8010 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Mark No. Description Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 77 5 6 7 8 5 6 7 8 C D F A B E Q8012 COMPOUND TRANSISTOR DTC124EKAT146 TNYJC05001 Q8013 COMPOUND TRANSISTOR DTC124EKAT146 TNYJC05001 Q8015 TRANSISTOR,SILICON KTA1504S_Y_RTK TAAA1504SY Q8016 COMPOUND TRANSISTOR DTC124EKAT146 TNYJC05001 Q8017 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8018 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8019 COMPOUND TRANSISTOR DTA143EKAT146 TPYJA05001 Q8020 COMPOUND TRANSISTOR DTC124EKAT146 TNYJC05001 Q8021 COMPOUND TRANSISTOR DTC124EKAT146TNYJC05001 Q8022 COMPOUND TRANSISTOR DTA124EKAT146 TPYJC05001 Q8023 COMPOUND TRANSISTOR DTA124EKAT146 TPYJC05001 Q8025 COMPOUND TRANSISTOR DTC124EKAT146 TNYJC05001 Q8027 COMPOUND TRANSISTOR DTC124EKAT146 TNYJC05001 Q8029 COMPOUND TRANSISTOR DTC124EKAT146TNYJC05001 Q8036 COMPOUND TRANSISTOR DTA124EKAT146 TPYJC05001 Q8301 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8302 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8310 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8311 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8314 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8315 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8320 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY Q8321 TRANSISTOR,SILICON KTC3875S_Y_RTKTCAA3875SY D652 LED LTL-1CHGE-002A 0021E5Q210 D681 LED LTL-1CHAE-002A 0021E3Q030 D701 DIODE,SILICON 1SS133T-77 D1VT001330 D1703 DIODE,SILICON 1SS133T-77 D1VT001330 D1704 DIODE,SILICON 1SS133T-77 D1VT001330 >D1706 DIODE,ZENER MTZJ12B T-77 D97U01201 D1707 DIODE,SILICON 1SS133T-77 D1VT001330 D3001 INFRARED LED LTE-3271T-012A-O 0010E00330 D3007 DIODE,SILICON 1SS133T-77 D1VT001330 D3009 DIODE,SILICON 1SS133T-77 D1VT001330 D8002 DIODE,SILICON 1SS133T-77 D1VT001330 D8003 DIODE,SILICON 1SS133T-77 D1VT001330 D8301 DIODE,SCHOTTKY RB721Q-40 T-77 D1VTB721Q0 D8302 DIODE,SCHOTTKY RB721Q-40 T-77 D1VTB721Q0 D8303 DIODE,SCHOTTKY RB721Q-40 T-77 D1VTB721Q0 D8307 DIODE,SCHOTTKY RB721Q-40 T-77 D1VTB721Q0 D8314 DIODE,SCHOTTKY RB721Q-40 T-77 D1VTB721Q0 COILS AND TRANSFORMERS L101 COIL,BIAS OSC 1626009 031626009R L102 COIL 100 UH 02167F101J L104 COIL 22 UH 02167F220J L105 COIL 22 UH 02167F220J L106 COIL 22 UH 02167F220J L107 COIL 22 UH 02167F220J L109 COIL 100 UH 021LA6101J L301 COIL 22 UH 02167F220J L651 COIL 100 UH 021LA6101J L701 COIL 22 UH 02167F220J L702 COIL 22 UH 02167F220J L703 COIL 100 UH 021LA6101J L704 COIL 22 UH 02167F220J L801 COIL 100 UH 02167F101J L1701 CORE,FERRITE W5T29X7.5X19 02AHB9A972 L1702 COIL 47 UH 02167F470J L3003 COIL 12 UH 021LA6120J L7301 COIL 1 UH 0216S71R0J Mark No. Description Part No. L7302 COIL 1 UH 0216S71R0J L7303 COIL 1 UH 0216S71R0J L7304 COIL 1 UH 0216S71R0J L7305 COIL 1 UH 0216S71R0J L7306 COIL 1 UH 0216S71R0J L7307 COIL 6.8 UH 0216S76R8J L7308 COIL 6.8 UH 0216S76R8J L7309 COIL 6.8 UH 0216S76R8J L8001 COIL 100 UH 021LA6101J L8002 COIL 100 UH 02167F101J L8003 COIL 22 UH 02167F220J L8301 COIL 22 UH 02167F220J L8302 COIL 100 UH 02167F101J L8305 COIL 100 UH 02167F101J L8306 COIL 220 UH 02167F221J SWITCHES SW651 SWITCH,TACT EVQ21505R 0504101T34 SW652 SWITCH,TACT EVQ21505R 0504101T34 SW653 SWITCH,TACT EVQ21505R 0504101T34 SW681 SWITCH,TACT EVQ11L05R 0504R01T38 SW682 SWITCH,TACT EVQ11L05R 0504R01T38 SW683 SWITCH,TACT EVQ11L05R 0504R01T38 SW684 SWITCH,TACT EVQ11L05R 0504R01T38 SW685 SWITCH,TACT EVQ11L05R 0504R01T38 SW686 SWITCH,TACT EVQ11L05R 0504R01T38 SW687 SWITCH,TACT EVQ11L05R 0504R01T38 SW688 SWITCH,TACT EVQ11L05R 0504R01T38 SW3001 SWITCH (LEAF) LSA-1144EAU 0508S11001 RESISTORS >R531 R,FUSE 22 OHM 1/4W R65584220 >R533 R,FUSE 2.7 OHM 1/4W R655842R7 >R1750 R,METAL OXIDE 1.5 OHM 2W R3X28A1R5 OTHERS B651 CORE,BEADS FCM2012H-102T04 024HC31022 B652 CORE,BEADS FCM2012H-102T04 024HC31022 B653 CORE,BEADS FCM2012H-102T04 024HC31022 B654 CORE,BEADS FCM2012H-102T04 024HC31022 B655 CORE,BEADS FCM2012H-102T04 024HC31022 B4001 CORE,BEADS FCM2012H-102T04 024HC31022 B4002 CORE,BEADS HCB2012K-600T25 024HC36001 B4003 CORE,BEADS HCB2012K-600T25 024HC36001 B4004 CORE,BEADS HCB2012K-600T25 024HC36001 B4005 CORE,BEADS HCB2012K-600T25 024HC36001 B4006 CORE,BEADS FCM2012H-102T04 024HC31022 B4007 CORE,BEADS FCM2012H-102T04 024HC31022 B4008 CORE,BEADS FCM2012H-102T04 024HC31022 B7301 CORE,BEADS FCM2012H-102T04 024HC31022 B7304 CORE,BEADS HCB2012K-600T25 024HC36001 B7305 CORE,BEADS HCB2012K-600T25 024HC36001 B7306 CORE,BEADS HCB2012K-600T25 024HC36001 B7307 CORE,BEADS HCB2012K-600T25 024HC36001 B8001 CORE,BEADS FCM2012H-102T04 024HC31022 B8002 CORE,BEADS FCM2012H-102T04 024HC31022 BT601 BATTERY, MANGAN R03(AB)E_2P_G 1412004008 CD102 CORD,JUMPER 2F061501 0122F061501 >CD501 CORD,SET AC 9619904 120961990 CD502 WPL6016038 FLAT CABLE AWM2468 A WG26 16C BLACK 160MM Mark No. Description Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 78 1 2 3 4 1 2 3 4 C D F A B E CD504 CORD,CONNECTOR CU641202 06CU641202 CD651 CORD,CONNECTOR CU252802 06CU252802 CP101 CONNECTOR PCB SIDE TOC-C09X-A1 697290620 CP102 CONNECTOR PCB SIDE IMSA-9604S-06C069J760599 CP103 WIRE HOLDER B2013H02-2P 067U002019 >CP502 WIRE HOLDER B2013H02-16P 067U01601 >CP681 CONNECTOR PCB SIDE A2001WR2-5P 069S25063 CD4001 CORD,JUMPER BH040061 12BH040061 CD6002 CABLE CPL02006 06CPL02006 CD6003 CORD,RCA PIN TD-020301-3 06CPBA2003 CD7301 CORD,JUMPER 2H0K1802 122H0K1802 CD7302 CORD,JUMPER 2H0K1802 122H0K1802 CD7303 CORD,JUMPER 2H0I1802 122H0I1802 CD7304 CORD,CONNECTOR CU2A2701 06CU2A2701 >CP1701 CONNECTOR PCB SIDE 52147-1610 069R2G058 CP1703 CONNECTOR PCB SIDE A2001WV2-10P069S2A0629 >CP3001 CONNECTOR PCB SIDE TMC-J12P-B2 06972C001 CP4001 CONNECTOR PCB SIDE 04_6274_000_800 069S2A0629 CP7304 CONNECTOR PCB SIDE A2001WV2-10P 069S2A0629 CP8301 069JVK0200 CONNECTOR PCB SIDE IMSA-9615S-20C-PP-A CP8302 069JVK0200 CONNECTOR PCB SIDE IMSA-9615S-20C-PP-A CP8303 069JVI0200 CONNECTOR PCB SIDE IMSA-9615S-18C-PP-A >DK4001 DECK CD DVR-R07OR 169V00030 ICP501 MICRO FUSE 20N_1000FS 0835C01003 ICP1701 MICRO FUSE 20N_1250FS 0835C01203 >M501 FAN MOTOR 2410ML-04W-B10-C47 1519X56L0 NR4001 R,NETWORK 4D03WGJ0470T5E 110P4470M4 NR4002 R,NETWORK 4D03WGJ0470T5E 110P4470M4 NR4003 R,NETWORK 4D03WGJ0470T5E 110P4470M4 NR4004 R,NETWORK 4D03WGJ0470T5E 110P4470M4 NR4005 R,NETWORK 4D03WGJ0470T5E 110P4470M4 NR4006 R,NETWORK 4D03WGJ0470T5E 110P4470M4 NR4007 R,NETWORK 4D03WGJ0470T5E 110P4470M4 NR4008 R,NETWORK 4D03WGJ0470T5E 110P4470M4 OS651 REMOTE RECEIVER PIC-37041LO-H 077Q037012 OS8001 OPTICAL DEVICE OFTG038101 07AQ000009 TM601 TRANSMITTER R56-0517 076R0JZ010 TU301 RF UNIT 115-V-H015ARE_G 162300041 V651 096F90R404 TUBE FLUORSCENT DISPLAY HNV-09SS48 X101 CRYSTAL HC-49/U 100DT3R528 X3001 CRYSTAL HC-49/U-S 100CT01002 X3002 CRYSTAL DT-26 100DA32R01 X3003 CRYSTAL HC-49/U-S 100CT01403 X4001 CRYSTAL DSO751SV 100DT02712 X8301 CERAMIC OSCILLATOR CSB500E5 1002A0R503 J651 RCA JACK MSP-281V31-A 060J421039 J652 RCA JACK MSP-281V40-B 060J401098 J653 RCA JACK MSP-281V42-B 060J401099 J654 JACK MDC-012V1-A_LF 063D700010 J8001 JACK MDC-012V1-A_LF 063D700009 J8002 RCA JACK MSP-213V2-432_NI_LF 060J431020 J8003 RCA JACK MSP-213V1-432_NI_LF 060J411031 J8004 JACK MDC-070-B_LF 063D700008 J8005 RCA JACK MSP-213V1-732_NI_LF 060J41033 J8006 RCA JACK MSP-213V1-652_NI_LF 060J411032 Mark No. Description Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 79 5 6 7 8 5 6 7 8 C D F A B E 6. ADJUSTMENT 6.1 SERVICING FIXTURES AND TOOLS (For 4 heads model) VHS Alignment Tape GGV1183 (VN1S-LI63H) GGV1184 (VN1S-X63) GGV1185 (VN2E-LI63H) GGF1506 Adapter GGF1507 Dial Torque Gauge (10~90 gf•cm) GGF1508 (60~600 gf•cm) GGF1509 Post Adjustment Screwdriver Part No. SV-TG0-030-000 (small) GGF1510 X Value Adjustment Screwdriver GGF1511 Master Plane GGF1512 Reel Disk Height Adjustment Jig GGV1186 Torque Tape (VHT-063) Part No. Parts Name Remarks GGV1183 VHS Alignment Tape Hi-Fi Audio (For 4 heads model) GGV1184 VHS Alignment Tape X Value Adjustment (For 4 heads model) GGV1185 VHS Alignment Tape EP Monoscope, 6 kHz (For 4 heads model) GGF1506 Adapter VSR Torque, Brake Torque (S Reel/T Reel Assy) GGF1507 Dial Torque Gauge (10~90 gf•cm) Brake Torque (T Reel Assy) GGF1508 Dial Torque Gauge (60~600 gf•cm) VSR Torque, Brake Torque (S Reel) GGF1509 Post Adjustment Screwdriver Guide Roller Adjustment GGF1510 X Value Adjustment Screwdriver X Value Adjustment GGF1511 Master Plane Reel Disk Heifht Adjustment GGF1512 Reel Disk Height Adjustment Jig Reel Disk Heifht Adjustment GGV1186 Torque Tape (VHT-063) Playback Torque, Back Tension Torque During Playback PREPARATION FOR SERVICING 1. While pressing the CH DOWN button on the set for more than 2 seconds, press the POWER button on the set simultaneously at the Power OFF. Although the DVD is connected, the DVD mode cannot be selected. 2. Press both CH UP button on the set and the REC button on the set for more than 2 seconds. (The BOT, EOT, and the Reel Sensor do not work and the VCR deck can be operated without a cassette tape.) 3. In case of using a cassette tape, press the EJECT button to insert or eject a cassette tape. Turn on the power and re-check the cable before checking the trouble points. When you servicing with connection of DVD, perform the operations above step 2 to step 3. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 80 1 2 3 4 1 2 3 4 C D F A B E 6.2 ADJUSTMENT ITEMS AND NECESSARY ADJUSTMENT POINTS 1 Adjustment Items [Mechanism Part] 1-1 CONFIRMATION AND ADJUSTMENT OF REEL DISK HEIGHT 2 1-2 CONFIRMATION AND ADJUSTMENT OF TENSION POST POSITION 3 1-3 CONFIRMATION OF PLAYBACK TORQUE AND BACK TENSION TORQUE DURING PLAYBACK 4 1-4 CONFIRMATION OF VSR TORQUE 5 1-5 CONFIRMATION OF REEL BRAKE 1. CONFIRMATION AND ADJUSTMENT 6 2-1 GUIDE ROLLER 7 2-2 CONFIRMATION AND ADJUSTMENT OF AUDIO/CONTROL HEAD 8 2-3 TAPE RUNNING ADJUSTMENT (X VALUE ADJUSTMENT) 9 2-4 CONFIRM HI-FI AUDIO 2. CONFIRMATION AND ADJUSTMENT OF TAPE RUNNING MECHANISM 10 [Electrical Part] 1-1 PG SHIFTER 11 DVD SIDE EEPROM (IC4002) INITIAL SETTING REPLACING EEPROM (IC4002) IC 12 REGION SETTING REPLACING NEW DVD LOADER 1. BASIC ADJUSTMENT www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 81 5 6 7 8 5 6 7 8 C D F A B E Mechanical point Electrical point Replacing Parts of Mechanism Assy When Adjustment Items Replacing REEL DISK (S REEL, T REEL) 1 2 3 4 5 None Mechanical point Electrical point Replacing PCB Assy or Electrical Parts Replacing DECK ASSY VCR MT PCB ASSY 10 None Mechanical point Electrical point Replacing HEAD (AUDIO CONTROL) CYLINDER UNIT ASSY 6 10 7 8 9 Mechanical point Electrical point Replacing IC4002 (DVD SIDE EEPROM) None 11 Mechanical point Electrical point Replacing DVD LOADER None 12 Mechanical point Electrical point Replacing TENSION BAND TENSION CONNECT TENSION ARM ASSY T BRAKE BAND T BRAKE SPRING T BRAKE ARM IDLLER ASSY CLUTCH ASSY 2 3 4 5 None www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 82 1 2 3 4 1 2 3 4 C D F A B E 6.3 SERVICE MODE LIST To enter one of the Sub-Service modes, hold a designated key on the unit pressed for a specified period of time while holding another designated key on the unit or on the remote control unit pressed. The following Sub-Service modes can be entered by first holding the designated key on the remote control unit pressed then pressing another designated key on the unit. For switching the RF output channels (CH 3/4) While the unit is off, hold the 3 or 4 key on the remote control unit pressed for at least 3 seconds. Mode of the Unit Key on the Unit Key on the Unit Specified Period (sec) Description VCR FF CH+ 2 For (1) initial setting of the µ-CON on the VCR side, (2) confirmation of initial settings for the Memory IC, and (3) displaying the accumulated time of playback and recording on the screen. VCR PLAY CH+ 2 Initialization to the state at shipment Note: Do NOT use this mode during normal servicing. This mode will reset the time setting, channel setting, and the accumulated time of playback/recording. VCR (Playback) CH+ CH– 2 For setting tracking to the center value Note: You can enter this mode by holding the ATR key on the remote control unit pressed for 2 seconds. VCR (Playback) REC/OTR DVD/VCR 2 For automatic adjustment of the PG shifter VCR CH+ REC/OTR 2 For entering Service mode Entering this mode disables the EOT/BOT/reel sensor and enables the VCR section of the unit to operate even if a tape is not loaded. VCR STOP CH+ 2 For entering DVD-Audio-Level/Separation Adjustment mode DVD CH– DVD/VCR 2 For displaying information VCR CH– S-BY/ON 2 For entering Operation-of-Only-VCR-Section mode Note: In this mode, you cannot switch to DVD mode even if connection of the DVD section has been made. Mode of the Unit Key on the Remote Control Unit Key on the Unit Specified Period (sec) Description DVD (NO DISC) 2 STOP 2 DVD (NO DISC) 0 STOP 2 F/W Writing mode DVD 6 STOP 2 For initial setting of µ-CON on the DVD side For setting and unlocking the TRAY Lock. This mode functions cyclically. DVD (NO DISC) 7 STOP 2 For canceling Parental Lock Note: This mode functions only when a disc is not loaded in DVD mode DVD (NO DISC) 8 STOP 2 For entering Region-Code Writing mode DVD (Playback, NO DISC) 9 STOP 2 For displaying Loader Information and error rates www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 83 5 6 7 8 5 6 7 8 C D F A B E 6.4 CONFIRMATION OF HOURS USED PLAY/REC total hours can be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0". 1. Connect the set to TV Monitor. 2. Turn on the POWER, and set to the VCR mode. 3. Press both CH UP button on the set and the FF button on the set for more than 2 seconds. The Fig. 1 screen will appear on TV Monitor. 4. After the confirmation of using hours, turn off the power. Fig. 1 MICON Version Initial setting content of MEMORY IC. Initial setting data check sum. Romcorrection data check sum. PLAY/REC total hours. = (16 × 16 × 16 × thousands digit value) + (16 × 16 × hundreds digit value) + (16 × tens digit value) + (ones digit value) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 84 1 2 3 4 1 2 3 4 C D F A B E 6.5 PREVENTIVE CHECKS AND SERVICE INTERVALS The following standard table depends on environmental conditions and usage. Parts replacing time does not mean the life span for individual parts. Also, long term storage or misuse may cause transformation and aging of rubber parts. The following list means standard hours, so the checking hours depends on the conditions. Parts Name Time 500 hours 1,000 hours 1,500 hours 2,000 hours 2,500 hours Notes Audio Control Head 7 7 7 ¶ ¶ Clean those parts in contact with the tape. Full Erase Head (Recorder only) 7 7 7 ¶ ¶ Capstan Belt ¶ ¶ ¶ ¶ Clean the rubber, and parts which the rubber touches Pinch Roller 7 ¶ ¶ ¶ ¶ Capstan DD Unit ¶ ¶ ¶ ¶ Loading Motor ¶ Tension Band ¶ ¶ ¶ ¶ T Brake Band ¶ ¶ ¶ ¶ Clutch Assy ¶ ¶ ¶ ¶ Idler Arm Assy ¶ ¶ ¶ ¶ Capstan Shaft 7 7 7 7 7 Tape Running Guide Post 7 7 7 7 7 Replace when rolling becomes abnormal. Cylinder Unit 7 ¶ ¶ ¶ ¶ Clean the Head 7 : Clean ¶ : Check it and if necessary, replace it NOTE After cleaning the heads with isopropyl alcohol, do not run a tape until the heads dry completely. If the heads are not completely dry and alcohol gets on the tape, damage may occur. 1. AUDIO CONTROL HEAD Clean the Audio Control Head with the cotton stick soaked by alcohol. Clean the full erase head in the same manner. (Refer to the figure below.) 2. TAPE RUNNING SYSTEM When cleaning the tape transport system, use the gauze moistened with isopropyl alcohol. 3. CYLINDER Wrap a piece of chamois around your finger. Dip it in isopropyl alcohol. Hold it to the cylinder head softly. Turn the cylinder head counterclockwise to clean it (in the direction of the arrow). (Refer to the figure below.) NOTE Do not exert force against the cylinder head. Do not move the chamois upward or downward on the head. Use the chamois one by one. CLEANING Audio Control Head Cylinder Head www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 85 5 6 7 8 5 6 7 8 C D F A B E 6.6 MECHANICAL ADJUSTMENTS 1. CONFIRMATION AND ADJUSTMENT Read the following NOTES before starting work. • Place an object which weighs between 450g~500g on the Cassette Tape to keep it steady when you want to make the tape run without the Cassette Holder. (Do not place an object which weighs over 500g.) 1-1: CONFIRMATION AND ADJUSTMENT OF REEL DISK HEIGHT 1. Turn on the power and set to the STOP mode. 2. Set the master plane (JG022) and reel disk height adjustment jig (JG024A) on the mechanism framework, taking care not to scratch the drum, as shown in Fig. 1-1-A. 3. While turning the reel and confirm the following points. Check if the surface "A" of reel disk is lower than the surface "B" of reel disk height adjustment jig (JG024A) and is higher than the surface "C". If it is not passed, place the height adjustment washers and adjust to 10 (+2, -0) mm. 4. Adjust the other reel in the same way. 1-2: CONFIRMATION AND ADJUSTMENT OF TENSION POST POSITION 1. Set to the PLAY mode. 2. Adjust the adjusting section for the Tension Arm position so that the Tension Arm top is within the standard line of Main Chassis. 3. While turning the S Reel clockwise, confirm that the edge of the Tension Arm is located in the position described above. • USING A CASSETTE TYPE TORQUE TAPE (JG100A) 1. After confirmation and adjustment of Tension Post position (Refer to item 1-2), load the cassette type torque tape (JG100A) and set to the PLAY mode. 2. Confirm that the right meter of the torque tape indicates 50~90gf•cm during playback in SP mode. 3. Confirm that the left meter of the torque tape indicates 25~40gf•cm during playback in SP mode. Master Plane (JG022) Master Plane (JG022) 10 (+0.2, -0) mm Reel Disk Adjusting section for the Tension Arm position Standard line of Main Chassis Tension Arm 0.5 mm (Adjustment range) Tension Band Bend The Tension Arm top will move to the inside direction of the Main Chassis. The Tension Arm top will move to the outside direction of the Main Chassis. Height Adjustment Washer 2.6 × 4.7 × T0.13 2.6 × 4.7 × T0.25 (B) (C) (A) Reel Disk Height Adjustment Jig (JG024A) Fig. 1-1-A Fig. 1-2-A Fig. 1-2-B Fig. 1-1-B Reel Disk Height Adjustment Jig (JG024A) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 86 1 2 3 4 1 2 3 4 C D F A B E 1-4: CONFIRMATION OF VSR TORQUE 1. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Set to the Picture Search (Rewind) mode. (Refer to Fig.1-4-B) 2. Then, confirm that it indicates 120~180gf•cm. NOTE Install the Torque Gauge on the reel disk firmly. Press the REW button to turn the reel disk. 1-5: CONFIRMATION OF REEL BRAKE TORQUE (S Reel Brake) (Refer to Fig. 1-4-B) 1. Once set to the Fast Forward mode then set to the Stop mode. While, unplug the AC cord when the Pinch Roller Block is on the position of Fig. 1-4-A. 2. Move the Idler Assy from the S Reel. 3. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Turn the Torque Gauge (JG002F) clockwise. 4. Then, confirm that it indicates 60~100gf•cm. (T Reel Brake) (Refer to Fig. 1-4-B) 1. Once set to the Fast Forward mode then set to the Stop mode. While, unplug the AC cord when the Pinch Roller Block is on the position of Fig. 1-4-A. 2. Move the Idler Assy from the T Reel. 3. Install the Torque Gauge (JG002E) and Adapter (JG002B) on the T reel. Turn the Torque Gauge (JG002E) counterclockwise. 4. Then, confirm that it indicates 30~50gf•cm. NOTE If the torque is out of the range, replace the following parts. 2. CONFIRMATION AND ADJUSTMENT OF TAPE RUNNING MECHANISM Tape Running Mechanism is adjusted precisely at the factory. Adjustment is not necessary as usual. When you replace the parts of the tape running mechanism because of long term usage or failure, the confirmation and adjustment are necessary. 2-1: GUIDE ROLLER 1. Playback the VHS Alignment Tape (JG001 or JG001B). (Refer to SERVICING FIXTURE AND TOOLS) 2. Connect CH-1 of the oscilloscope to TP101 (Envelope) and CH-2 to TP3002 (SW Pulse). 3. Press and hold the ATR button on the remote control more than 2 seconds to set tracking to center. 4. Trigger with SW Pulse and observe the envelope. (Refer to Fig. 2-1-A) 5. When observing the envelope, adjust the Adjusting Driver (JG005) slightly until the envelope will be flat. Even if you press the Tracking Button, adjust so that flatness is not moved so much. 6. Adjust so that the A : B ratio is better than 3 : 2 as shown in Fig. 2-1-B, even if you press the Tracking Button to move the envelope (The envelope waveform will begin to decrease when you press the Tracking Button). 7. Adjust the PG shifter during playback. (Refer to the ELECTRICAL ADJUSTMENTS) NOTE After adjustment, confirm and adjust A/C head. (Refer to item 2-2) The position at FF mode. Stop at this position. The position at STOP mode. Caption DD Unit Cassette Opener Pinch Roller Block Cassette Holder Assy S Reel T Reel Torque Gauge/Adpter (JG002F/JG002B) Torque Gauge/Adpter (JG002F/JG002B) CH-1 Envelope (TP101) CH-2 SW Pulse (TP3002) Max Max A : B 3 : 2 Entrance Exit CH-1 Track CH-2 Track Fig. 1-4-A Fig. 2-1-A Fig. 2-1-B Fig. 1-4-B Check Item Replacement Part 1-4 Idler Assy / Clutch Assy 1-5 S Reel side : S Reel/ Tension Band/Tension Connect/Tension Arm Assy T Reel side : T Reel/ Brake Band/T Brake Spring /T Brake Arm A B www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 87 5 6 7 8 5 6 7 8 C D F A B E 2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/CONTROL HEAD When the Tape Running Mechanism does not work well, adjust the following items. 1. Playback the VHS Alignment Tape (JG001 or JG001B). (Refer to SERVICING FIXTURE AND TOOLS) 2. Confirm that the reflected picture of stamp mark is appeared on the tape prior to P4 Post as shown in Fig. 2-2-A. a) When the reflected picture is distorted, turn the screw 1 clockwise until the distortion is disappeared. b) When the reflected picture is not distorted, turn the screw 1 counterclockwise until little distortion is appeared, then adjust the a). 3. Turn the screw 2 to set the audio level to maximum. 4. Confirm that the bottom of the Audio/ Control Head and the bottom of the tape is shown in Fig. 2-2-C. c) When the height is not correct, turn the screw 3 to adjust the height. Then, adjust the 1~3 again. 2-3: TAPE RUNNING ADJUSTMENT (X VALUE ADJUSTMENT) 1. Confirm and adjust the height of the Reel Disk. (Refer to item 1-1) 2. Confirm and adjust the position of the Tension Post. (Refer to item 1-2) 3. Adjust the Guide Roller. (Refer to item 2-1) 4. Confirm and adjust the Audio/Control Head. (Refer to item 2-2) 5. Connect CH-1 of the oscilloscope to TP3002, CH-2 to TP101 and CH-3 to HOT side of Audio Out Jack. 6. Playback the VHS Alignment Tape (JG001S or JG001T). (Refer to SERVICING FIXTURE AND TOOLS) 7. Press and hold the ATR button on the remote control more than 2 seconds to set tracking to center. 8. Set the X Value adjustment driver (JG153) to the 4 of Fig. 2-2-B. Adjust X value so that the envelope waveform output becomes maximum. Check if the relation between Audio and Envelope waveform becomes (1) or (2) of Fig. 2-3. 9. Playback the VHS Alignment Tape (JG195). (Refer to SERVICING FIXTURE AND TOOLS) 10. Check if the picture is played back correctly. 2-4: CONFIRM HI-FI AUDIO (Hi-Fi model only) 1. Connect CH-1 of the oscilloscope to TP101 and CH-2 to the Hi-Fi Audio Out Jack. 2. Playback the VHS Alignment Tape (JG001P or JG001Q). (Refer to SERVICING FIXTURE AND TOOLS) 3. Press and hold the ATR button on the remote control more than 2 seconds to set tracking to center. 4. Press the Tracking Up button and count number of steps which the audio output is changed from Hi-Fi (10KHz) to MONO (6KHz). 5. Press and hold the ATR button on the remote control more than 2 seconds to set tracking to center. 6. Press the Tracking Down button and count number of steps which the audio output is changed from Hi-Fi (10KHz) to MONO (6KHz). 7. If the difference are more than 3 steps, set the X Value adjustment driver (JG153) to 4 of Fig. 2-2-B. Change the X Value and adjust it so that the value becomes within 2 steps. Audio/Control Head Audio/Control Head Audio/Control Head Tape 0.25 ± 0.05 mm P4 Cap Stamp Mark Reflected picture of Stamp Mark Envelope CH-3 Audio (1) (2) Fig. 2-2-A Fig. 2-3 Fig. 2-2-B Fig. 2-2-C 1 4 3 2 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 88 1 2 3 4 1 2 3 4 C D F A B E 3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE 9 10 8 7 6 5 4 3 2 1 1. Tension Connect 2. Tension Arm 3. Guide Roller 4. Audio/Control Head 5. X value adjustment driver hole 6. P4 Post 7. T Brake Spring 8. T Reel 9. S Reel 10. Adjusting section for the Tension Arm position www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 89 5 6 7 8 5 6 7 8 C D F A B E 6.7 ELECTRICAL ADJUSTMENTS Read and perform this adjustment when repairing the circuits or replacing electrical parts or PCB assemblies. 1. BASIC ADJUSTMENT CAUTION When you exchange IC and Transistor for a heat sink, apply the silicon grease (YG6260M) on the contact section of the heat sink. Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.) 1-1: PG SHIFTER CONDITIONS MODE-PLAYBACK Input Signal-Alignment Tape (JG001B) INSTRUCTIONS 1. Connect CH-1 on the oscilloscope to TP3002 and CH-2 to J8005. 2. Playback the alignment tape. (JG001B) 3. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 4. Press both CH UP button on the set and the STOP button on the set for more than 2 seconds. 6.5 H CH-2 CH-1 Fig. 1-1-A 6.5 H CH-2 CH-1 Fig. 1-1-B www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 90 1 2 3 4 1 2 3 4 C D F A B E 2. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION) J653 J652 J651 V651 TP101 TP701 TP3002 CP8303 TP651 TU301 OS8001 J8004 CP8302 CP8301 CP1701 CP1703 J8002 J8005 J8006 J8003 J8001 J654 CP651 TP8301 TP8302 CP681 DVD/HD MPEG PCB POWER PCB OPERATION PCB DECK CD CP103 FE HEAD CP102 AC HEAD CD102 CD651 CP506 CP502 CP504 CP7301 CP7302 CP7303 CP7304 CD7304 VCR PCB FAN MOTOR CD502 CD7301 CD7302 CD7303 CP4001 OS651 CP501 CD501 AC IN B C A D CD4001 CD504 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 91 5 6 7 8 5 6 7 8 C D F A B E 6.8 WHEN REPLACING NEW DVD LOADER NOTE: If a service repair is undertaken where it has been required to change the New DVD Loader, Region setting is needed. If the Region setting does not performed, only the Region Free disc can be played. Region setting can only be done once. So, take notice very carefully. 1. Connect the set to TV Monitor. 2. Turn on the POWER, and set to the DVD mode. 3. Press both Channel button (8) on the remote control and the STOP button on the set for more than 2 seconds. Tray will open. 4. Place your Region setting disc (Region 1) on the tray and close. Writing will start. 5. After the writing, the writing Region No. will appear on the TV Monitor. Perform the initializing of shipping (*) 6. Press both CH UP button on the set and the PLAY button on the set for more than 2 seconds. 7. After the finishing of the initializing of shipping, the unit will turn off automatically. * : When initializing to shipping data, the VCR operating time record is cleared. Check for the Region No. 8. Turn on the POWER, and set to the DVD mode. 9. Press both CH DOWN button on the set and the DVD/VCR button on the set for more than 2 seconds. Information screen will be displayed on the TV Monitor. (Refer to Fig. 1) 10. If the writing Region No. is appeared, the Region setting is completed. 11. Turn off the power. Fig. 1 Region No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 92 1 2 3 4 1 2 3 4 C D F A B E 6.9 WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: After the DATA change, if the ENTER button is not pressed at the DATA selection mode and the power is turned off, the DATA change does not performed. After the DATA change, press the ENTER button by all means and set to the ADDRESS selection mode, then turn off the power. DVD side EEPROM (IC4002) initial setting NOTE: INI 3FF data can not be set. The datas for the address excepting from 3A0 to 3FF are displayed “ERR”. This unit is not defective. 1. Connect the set to TV Monitor. 2. Turn on the POWER, and set to the DVD mode. 3. Press both Channel button (6) on the remote control and the STOP button on the set for more than 2 seconds. ADDRESS and DATA will appear on TV Monitor as Fig 1 and the ADDRESS is now selected. 4. Input the ADDRESS by using Channel +/- button or the following buttons below. Numbers are 10 keys from 0 to 9, Alphabets are A: VCR EJECT, B: DVD OPEN/CLOSE, C: DVD/VCR, D: TIMER REC, E: INPUT SELECT, F: DISPLAY/CALL. 5. Press ENTER to select DATA. 6. Again, step through the DATA using Channel + or - button until required DATA value has been selected. 7. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 8. Repeat steps 4 to 7 until all data has been checked. 9. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping (*). 10. Turn on the POWER, and set to the DVD mode. 11. Press both CH UP button on the set and the PLAY button on the set for more than 2 seconds. 12. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC. * : When initializing to shipping data, the VCR operating time record is cleared. INIT +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F 3A0 01 01 00 01 02 00 00 00 02 07 01 02 01 02 02 00 3B0 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3C0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3D0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3E0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3F0 00 00 00 00 00 00 00 00 00 00 00 00 00 01 09* * RT500=09 RT300=11 --- Table 1 Fig. 1 ADDRESS DATA * Do not change other adress data. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 93 5 6 7 8 5 6 7 8 C D F A B E 7. GENERAL INFORMATION 7.1 RE-WRITE FOR DVD FIRMWARE 1. Connect the set to TV Monitor. 2. Turn on the POWER, and set to the DVD mode. 3. Confirm that the “No Disc” will be appeared on the screen. A disc is already inserted, eject the disc and power it off and on again. 4. Open the DVD tray. 5. Press both Channel button (2) on the remote control and the STOP button on the set for more than 2 seconds. 6. Press OPEN/CLOSE button on the set to check if all the keys on the unit do not function. NOTE: To check if DVD Write mode is set. 7. Place the Up-Date Disc and close the tray by hand. (Refer to SERVICING FIXTURE AND TOOLS) 8. Automatic read will start and "SDRAM writing" will be displayed on the screen. 9. Approx. 7 seconds later, the tray will open automatically. Remove the Up-Date Disc. The display will change to “FLASH writing”. 10. Then, Approx. 2 minutes 30 seconds later, the above indication will disappear and the tray will close automatically. When the "Please Reboot" appears on the screen, the writing will be finished. NOTE: Do not turn off the unit on the way or push the tray by hand to close it. Up-Date error will happen and can not be done with the Up-Date of Up-Date Disc. 11. Unplug the AC cord, then plug it in. After the write, set to the initializing of shipping (*). 12. Turn on the POWER, and set to the DVD mode. 13. Press both CH UP button on the set and the PLAY button on the set for more than 2 seconds. 14. After the finishing of the initializing of shipping, the unit will turn off automatically. * : When initializing to shipping data, the VCR operating time record is cleared. CHECK FOR THE FIRMWARE VERSION 15. Turn on the POWER, and set to the DVD mode. 16. Press both CH DOWN button on the set and the DVD/VCR button on the set for more than 2 seconds. Information screen will be displayed on the TV Monitor. (Refer to Fig. 1) 17. When the changed version displays, the Re-write will be completed. 18. Turn off the power Fig. 1 Firmware version www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 94 1 2 3 4 1 2 3 4 C D F A B E 7.2 MEASUREMENT OF ERROR RATE [ Measurement Steps ] 1 ) Load the disc that you want to measure the error rate of. 2 ) During playback, press "9" on the remote control and "STOP" on the main unit at the same time to measure the error rate for that part of the disc. 3 ) After the error rate has been measures, it is displayed on the screen. (This display is not updated.) 4 ) To clear the error rate display from the screen, press "9" on the remote control and "STOP" on the main unit at the same time again. When clearing this display, the error rate measurement is not executed. Fig. 1 (Background is input picture.) State : xxh numerator of PO : xxx denominator of PO : xxx numerator of PI : xxx (*) denominator of PI : xxx (*) Error rate value = numerator of PI / denominator of PI (*) : decimal digit Table 1: List of Reference Value Disc Type Recording Mode Reference Value DVD-VIDEO 8.0 × 10 DVD-R Video mode 1.0 × 10 DVD-RW Video mode 1.0 × 10 – 4 – 3 – 3 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 95 5 6 7 8 5 6 7 8 C D F A B E 7.3 POWER ON SEQUENCE Power on Sequence AT+5V[µ-CON] VCR µ-CON,RESET IC AT+5.2V OPERATION, REMOTE CONTROL SIGNAL RECEPTION,EEP-ROM EOT/BOT,REEL,MS EACH SENSOR,CENTER LED MOTOR+12V VCR DECK(CYLINDER,CAPSTAN, LOADING EACH MOTOR) VCR VCR_P_ON-L (from U-COM) Q1717(P.ON SW) BLOCK P.CON+12V IC701(HI-FI IC) (REGULATOR SIDE) HEATER +/- FIP -22V IC651(FIP DRIVER) AT+13V IC1701(VOLT CURRENT CONTROL) UNREG+3.3V MP_P.CON1.8V,3.3V REGULATOR MPEG_P_ON-L Q1701(MP POWER SW) MP_P.CON+1.8V DVD BLOCK MP_P.CON+3.3V DVD BLOCK DVD MPEG5V_ON-H (from U-COM) (from U-COM) Q1722(MPEG P.CON SW) BLOCK MP_P.CON+5V DVD BLOCK DRIVE_ON-H (from U-COM) IC502(DRIVE 12V REGULATOR) P.CON+12V DVD UNIT,FAN MOTOR (POWER SIDE) P.CON+D5V DVD UNIT AC IN P.ON www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 96 1 2 3 4 1 2 3 4 C D F A B E 7.4 DISC REMOVAL METHOD 7.5 TAPE REMOVAL METHOD AT NO POWER SUPPLY 1. Insert a fine rod (wire etc.) into the hole of the Front Cabinet as shown by the arrow. (Refer to Fig. 1) The Tray is opened. 2. Draw the Tray. Fig. 1 DVD Flap Front Cabinet 1. Remove the Top Cabinet, Front Cabinet and DVD Block. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) 2. Remove one screw of the Loading Motor from the insert hole for screw driver and remove the Loading Motor. 3. Rotate the Pinch Roller Cam in the direction of the arrow by hand to slacken the Video Tape. (Refer to Fig. 2) 4. Rotate the Clutch Ass'y either of the derections to wind the Video Tape in the Cassette Case. 5. Repeat the above step 3~4. Then take out the Video Cassette from the Deck Chassis. Be careful not to scratch on the tape. Fig. 1 Fig. 2 Insert hole for screwdriver Capstan DD Unit Main Chassis (Front Side) Clutch Assy Main Cam Pinch Roller Cam Screw Loading Motor www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 97 5 6 7 8 5 6 7 8 C D F A B E 7.6 PARENTAL CONTROL-RATING LEVEL 7.7 TRAY LOCK If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the steps below. 1. Turn Unit ON. 2. Press and hold the '7' key on the remote control unit. 3. Simultaneously press and hold the 'STOP' key on the front panel. 4. Hold both keys for more than 2 seconds. 5. The On Screen Display message 'PASSWORD UNLOCK' will appear. 6. The 4 digit password has now been cleared NB: No indications on the screen when the Parental Lock is setting. 4 DIGIT PASSWORD CANCELLATION Tray cannot be opened by setting the Tray Lock, please follow the steps below. 1. Turn Unit ON. 2. Press and hold the '0' key on the remote control unit. 3. Simultaneously press and hold the 'STOP' key on the front panel. 4. Hold both keys for more than 2 seconds. 5. Press the OPEN/CLOSE key on the front panel to check the Tray Lock setting. NB: No indications on the screen when the Tray Lock is setting. To unlock the Tray Lock, follow the steps above again. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 98 1 2 3 4 1 2 3 4 C D F A B E 7.8 DISASSEMBLY 1-1: TOP CABINET AND FRONT CABINET (Refer to Fig. 1-1) 1. Remove the 5 screws 1. 2. Remove the Top Cabinet in the direction of arrow (A). 3. Disconnect the following connector: (CP681). 4. Unlock the 10 supports 2. 5. Remove the Front Cabinet in the direction of arrow (B). 6. Remove the 3 screws 3. 7. Remove the Operation PCB in the direction of arrow (C). 1-3: DECK CD AND DVD/HD MPEG PCB (Refer to Fig. 1-3) 1. Remove the 2 screws 1. 2. Remove the Deck Shield Assy in the direction of arrow (A). 3. Remove the 6 screws 2. 4. Disconnect the following connectors: (CP504, CP1703, CP8301,CP8302, CP8303). 5. Remove the Deck CD Block in the direction of arrow (B). 6. Remove the 4 screws 3. 7. Remove the MPEG Shield in the direction of arrow (C). 8. Disconnect the following connector: (CP4001). 9. Remove the DVD/HD MPEG PCB in the direction of arrow (D). 10. Remove the 2 screws 4. 11. Remove the DVD Angle (L) in the direction of arrow (E). 12. Remove the 2 screws 5. 13. Remove the DVD Angle (R) in the direction of arrow (F). 1-2: FLAP (Refer to Fig. 1-2) 1. Open Flap to 90° and flex in direction of arrow (A), at the same time slide in direction of arrow (B). 2. Then lift in direction of arrow (C). Fig. 1-1 Fig. 1-3 Fig. 1-2 1 1 1 1 3 3 3 3 3 3 3 2 2 2 2 2 2 5 5 2 2 4 4 1 1 2 2 2 2 2 2 2 2 1 Top Cabinet Operation PCB DVD Angle (L) DVD Angle (R) DVD/HD MPEG PCB MPEG Shield Deck Shield Assy Deck CD Flap Front Cabinet (A) (A) (D) (C) (B) (E) (F) (B) (C) (A) (B) 1. REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 99 5 6 7 8 5 6 7 8 C D F A B E 1-4: POWER PCB (Refer to Fig. 1-4) 1. Remove the 2 screws 1. 2. Disconnect the following connector: (CP506). 3. Remove the Fan Motor in the direction of arrow (A). 4. Remove the 3 screws 2. 5. Disconnect the following connector: (CP1701). 6. Remove the Power PCB in the direction of arrow (B). 1-6: VCR PCB (Refer to Fig. 1-6) 1. Remove the screw 1. 2. Remove the screw 2. 3. Remove the 7 screws 3. 4. Remove the Jack Shield. 5. Remove the VCR PCB in the direction of arrow. 1-5: VCR DECK (Refer to Fig. 1-5) NOTE: Do not remove the cable at the FE Head section. The FE Head may be damaged if you remove the cable by force. 1. Unlock the 2 supports 1 and remove the Top Holder. 2. Remove the screw 2. 3. Remove the FE Head. 4. Move the Cassette Holder Assy to the back side. 5. Remove the 3 screws 3. 6. Disconnect the following connectors: (CP101, CP102, CP3001). 7. Remove the AC Head Cover and VCR Deck in the direction of arrow. Fig. 1-4 Fig. 1-6 Fig. 1-5 2 2 1 1 3 3 3 3 3 3 3 1 1 1 3 3 3 2 2 2 Power PCB Jack Shield Bottom Plate VCR PCB Bottom Plate AC Head Cover FE Head VCR Deck Top Holder Fan Motor (A) (B) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 100 1 2 3 4 1 2 3 4 C D F A B E 2-1: TOP BRACKET (Refer to Fig. 2-1) 1. Extend the 2 supports 1. 2. Slide the 2 supports 2 and remove the Top Bracket. NOTE 1. After the installation of the Top Bracket, bend the support 1 so that the Top Bracket is fixed. 2-2: CASSETTE HOLDER ASSY (Refer to Fig. 2-2) 1. Move the Cassette Holder Assy to the front side. 2. Push the Locker R to remove the Cassette Side R. 3. Remove the Cassette Side L. NOTE: 1. In case of the Locker R installation, check if the one position of Fig.2-3-B are correctly locked. 2. When you install the Cassette Side R, be sure to move the Locker R after installing. 2-4: LINK UNIT (Refer to Fig. 2-4) 1. Set the Link Unit to the Eject position. 2. Unlock the support 1. 3. Remove the (A) side of the Link Unit first, then remove the (B) side. 2-5: LINK LEVER/FLAP LEVER (Refer to Fig. 2-5) 1. Extend the support 1. 2. Remove the Link Lever. 3. Remove the Flap Lever. Fig. 2-1 Fig. 2-3-B Fig. 2-4 Fig. 2-5 1 1 1 1 1 1 2 1 2 2 1 Top Bracket Top Bracket Main Chassis Main Chassis Main Chassis Locker Spring Locker R Locker R Cassette Side R Check it this position is locked. Cassette Holder Cassette Side L Flap Lever Link Lever Cassette Side R Link Unit Cassette Side L Cassette Side R Link Unit Link Unit (A) (B) Main Chassis Main Chassis Locker R Main Chassis 2. REMOVAL OF VCR DECK PARTS Fig. 2-2 2-3: CASSETTE SIDE L/R (Refer to Fig. 2-3-A) 1. Remove the Locker Spring. 2. Unlock the 4 supports 1 and then remove the Cassette Side L/R. 3. Unlock the support 2 and then remove the Locker R. Fig. 2-3-A www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 101 5 6 7 8 5 6 7 8 C D F A B E 2-6: LOADING MOTOR/WORM (Refer to Fig. 2-6-A) 1. Remove the screw 1. 2. Remove the Loading Motor. 3. Remove the Worm. NOTE: 1. In case of the Worm installation, check if the value of the Fig. 2-6-B is correct. 2. In case of the Loading Motor installation, hook the wire on the Cassette Opener as shown Fig. 2-6-C. 3. When installing the wires between Capstan DD Unit and Loading Motor, connect them correctly as shown Fig. 2-6-D. 2-7: TENSION ASSY (Refer to Fig. 2-7-B) 1. Turn the Pinch Roller Cam clockwise so that the Tension Holder hook is set to the position of Fig. 2-7-A to move the Tension Arm Assy. 2. Remove the Tension Spring. 3. Unlock the 2 supports 1 and remove the Tension Band. 4. Unlock the support 2 and remove the Tension Arm Assy. 5. Unlock the support 3 and remove the Tension Connect. 6. Float the hook 4 and turn it clockwise then remove the Tension Holder. NOTE: 1. In case of the Tension Band installation, note the direction of the installation. (Refer to Fig. 2-7-C) 2. In case of the Tension Band installation, install correctly as Fig. 2-7-D. 3. In case of the Tension Connect installation, install as the circled section of Fig. 2-7-E. Fig. 2-6-A Fig. 2-7-A Fig. 2-7-B Fig. 2-7-C Fig. 2-7-D Fig. 2-7-D 1 1 3 2 4 1 Main Chassis Screw Torque: 3 ± 0.5kgf•cm Loading Motor Worm Tension Arm Assy Tension Band Tension Connect Tension Connect Tension Connect Main Chassis Tension Connect Tension Connect Tension Spring Tension Arm Assy Tension Holder Tension Band Tension Band Tension Band [OK] [NG] Loading Motor Pink Loading Motor White L2 Capstan DD Unit L1 Cassette Opener Safety surface for pressing of the insert. 19.2 ± 0.1mm Fig. 2-6-B Fig. 2-6-C Fig. 2-6-D www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 102 1 2 3 4 1 2 3 4 C D F A B E 2-8: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-8-A) 1. Remove the T Brake Spring. 2. Turn the T Brake Arm clockwise and bend the hook section to remove it. 3. Unlock the 2 supports 1 and remove the T Brake Band. NOTE: 1. In case of the T Brake Band installation, install correctly as Fig. 2-8-B. 2-9: S REEL/T REEL/IDLER ARM ASS'Y/IDLER GEAR (Refer to Fig. 2-9-A) 1. Remove the S Reel and T Reel. 2. Remove the 2 Polyslider Washers 1. 3. Remove the Idler Arm Ass'y and Idler Gear. NOTE: 1. Take care not to damage the gears of the S Reel and T Reel. 2. The Polyslider Washer may be remained on the back of the reel. 3. Take care not to damage the shaft. 4. Do not touch the section "A" of S Reel and T Reel. (Use gloves.) (Refer to Fig. 2-9-A) Do not adhere the stains on it. 5. When you install the reel, clean the shaft and grease it (FG-84M). (If you do not grease, noise may be heard in FF/REW mode.) 6. After installing the reel, adjust the height of the reel. (Refer to MECHANICAL ADJUSTMENT) NOTE: 1. In case of the S Reel and T Reel installation, check if the correct parts are installed. (Refer to Fig. 2-9-B) 2. In case of the Idler Arm Ass'y installation, install correctly as Fig. 2-9-C. And also set it so that the section "B" of Fig. 2-9-A is placed under the Main Chassis tab. Fig. 2-8-A Fig. 2-8-B Fig. 2-9-A Fig. 2-9-B Fig. 2-9-C 1 1 1 1 T Brake Band T Brake Band Clutch Gear Clutch Gear T Brake Band Hook Section T Brake Arm T Brake Arm Big Hole (S Reel) Small Hole (T Reel) T Brake Arm T Brake Spring (A) (A) (B) T Reel S Reel Idler Gear Idler Arm Assy Idler Arm Assy Idler Arm Assy [OK] [NG] [OK] [NG] www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 103 5 6 7 8 5 6 7 8 C D F A B E 2-10: CASSETTE OPENER/PINCH ROLLER BLOCK/P5 ARM ASSY (Refer to Fig. 2-10-A) 1. Unlock the support 1 and remove the Cassette Opener. 2. Remove the Pinch Roller Block and P5 Arm Assy. NOTE: 1. Do not touch the Pinch Roller. (Use gloves.) 2. In case of the Pinch Roller Block and the Pinch Roller Cam installation, install correctly as Fig. 2-10-B. 2-11: A/C HEAD (Refer to Fig. 2-11-A) 1. Remove the screw 1. 2. Remove the A/C Head Base. 3. Remove the 3 screws 2. 4. Remove the A/C Head and A/C Head Spring. NOTE: 1. Do not touch the A/C Head. (Use gloves.) 2. When you install the A/C Head Spring, install as shown in Fig. 2-11-B. 3. When you install the A/C Head, tighten the screw (1) first, then tighten the screw (2), finally tighten the screw (3). 2-12: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-12) 1. Remove the screw 1. 2. Remove the FE Head. 2-13: AHC ASSY/CYLINDER UNIT ASSY (Refer to Fig. 2-13) 1. Unlock the support 1 and remove the AHC Assy. 2. Disconnect the following connector: (CD2001) 3. Remove the 3 screws 2. 4. Remove the Cylinder Unit Assy. NOTE: 1. When you install the Cylinder Unit Assy, tighten the screws from (1) to (3) in order while pulling the Assy toward the left front direction. Fig. 2-10-A Fig. 2-10-B Fig. 2-11-A Fig. 2-11-B Fig. 2-12 Fig. 2-13 1 1 1 2 2 2 1 2 2 2 Cassette Opener FE Head Pinch Roller Block P5 Arm Assy Main Chassis Spring Position Can be seen the hole of the Pinch Roller Cam. Can be seen the hole of the Main Cam. Pinch Roller Block (1) (1) (2) (2) (3) (3) A/C Head A/C Head Spring AHC Assy Cylinder Unit Assy A/C Head Base P5 Arm Assy Screw Torque: 5 ± 0.5kgf•cm (Screw 1) Screw Torque: 3 ± 0.5kgf•cm • Screw Torque: 5 ± 0.5kgf•cm • The FE Head is not installed on the Video Cassette Player. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 104 1 2 3 4 1 2 3 4 C D F A B E 2-14: CAPSTAN DD UNIT (Refer to Fig. 2-14) 1. Remove the Capstan Belt. 2. Remove the screw 1. 3. Remove the Capstan Holder. 4. Remove the 3 screws 2. 5. Remove the Capstan DD Unit. 2-15: MAIN CAM/PINCH ROLLER CAM/JOINT GEAR (Refer to Fig. 2-15-A) 1. Remove the E-Ring 1, then remove the Main Cam. 2. Remove the E-Ring 2, then remove the Pinch Roller Cam and Joint Gear. NOTE: 1. In case of the Pinch Roller Cam and Main Cam installation, install them as the circled section of Fig. 2-15-B so that the each markers are met. (Refer to Fig. 2-15-B) 2-16: LOADING GEAR S/T UNIT (Refer to Fig. 2-16-A) 1. Remove the E-Ring 1 and remove the Main Loading Gear. 2. Remove the Main Rod, Tension Lever, Loading Arm S Unit and Loading Arm T Unit. NOTE: 1. When you install the Loading Arm S Unit, Loading Arm T Unit and Main Loading Gear, align each marker. (Refer to Fig. 2-16-B) Fig. 2-14 Fig. 2-15-A Fig. 2-15-B Fig. 2-16-B 1 1 1 2 2 2 2 Capstan Belt Pinch Roller Cam Marker Marker Marker Main Cam Capstan Holder Capstan DD Unit Main Loading Gear Main Loading Gear Loading Arm T Unit Loading Arm T Unit Loading Arm S Unit Loading Arm S Unit Main Rod Tension Lever Main Cam Pinch Roller Cam Joint Gear Fig. 2-16-A Screw Torque: 4 ± 0.5kgf•cm www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 105 5 6 7 8 5 6 7 8 C D F A B E Discs on which video can be recorded To record video with this unit, use the discs below: Media type Logo mark DVD-RW Ver.1.0 Ver.1.1 Ver.1.2 Ver.1.1CPRM support DVD-R Ver.2.0 (Ver.2.0 /4x /8x) DVD-RW • The disc can be erased and used again about 1,000 times. • Only the VR mode can be used for Ver.1.0 discs. • With Ver.1.1/1.2 discs, you can record by selecting the VR mode or Video mode. • When you record in the VR mode, you can repeatedly record and erase. By erasing unnecessary titles, you effectively increase remaining time. • When you record in the Video mode, you can record until the disc becomes full. • When you use the Video mode, you can newly record on the disc by formatting the disc. However, if the disc is formatted, all the recorded contents will be erased. DVD-R • You can record on the disc only in the Video mode. • You can record until the disc becomes full. • Finalizing the discs allows playback on other DVD players. However, the finalized discs can no longer be recorded. • Discs can be recorded to repeatedly until they are finalized. Note • There are some players that cannot playback discs that were recorded with this unit. We cannot guarantee the playback with other units. • This unit cannot record on DVD-R and DVD-RW discs that are 8 cm in diameter. • This unit cannot record on CD-R or CD-RW. Recording format This unit has two modes for formatting discs for recording: VR mode and Video mode. When a blank, new disc is loaded into this unit, the automatic format function starts to format the disc. (For the disc format setting in this step.) VR mode • This mode can be used for DVD-RW. • In this mode, the discs can be recorded and edited repeatedly. • The disc recorded in this mode can be played back with other DVD -RW-compatible players. • When a Ver.1.1 CPRM or Ver .1.2 CPRM disc is used, you can record a “Copy Once ” program. Video mode • This mode can be used for DVD-R and DVD-RW (Ver.1.1/1.2). • When you finalize the disc after recording, the disc recorded with this unit can be played back with other DVD players. • Recording, editing or playback of an unfinalized disc can be done only with this unit. However, there is some limitation to editing operations. • In this mode, you cannot record a “Copy Once” program. • When you record a TV program of a bilingual broadcast, only one of the audio modes can be recorded. You have to select it. Format modes that can be used each disc The usable format depends on the media type as shown in the below table. Media type Format DVD-RW Ver.1.0 DVD-RW Ver.1.1 and 1.2 DVD-R Ver.2.0 (Ver.2.0/4x/8x) Available functions VR mode VR mode Video mode Video mode Playback, recording and editing (Original/playlist) Playback, recording and editing (Original/playlist) Playback and recording Editing (with limitation) Playback and recording Editing (with limitation) Ver.1.2CPRM support 2-17: CLUTCH ASSY/RING SPRING/CLUTCH LEVER/CLUTCH GEAR (Refer to Fig. 2-17-A) 1. Remove the Polyslider Washer 1. 2. Remove the Clutch Assy and Ring Spring. 3. Remove the Clutch Lever. 4. Remove the Coupling Gear, Coupling Spring and Clutch Gear. NOTE: 1. In case of the Clutch Assy installation, install it with inserting the spring of the Clutch Assy into the dent of the Coupling Gear. (Refer to Fig. 2-17-B) 2-18: CASSETTE GUIDE POST/INCLINED BASE S/T UNIT/P4 CAP/LED REFLECTOR (Refer to Fig. 2-18-A) 1. Remove the P4 Cap. 2. Unlock the support 1 and remove the Cassette Guide Post. 3. Remove the Inclined Base S/T Unit. 4. Remove the screw 2. 5. Remove the LED Reflector. NOTE: 1. Do not touch the roller of Guide Roller. 2. In case of the P4 Cap installation, install it with parallel for "A" and "B" of Fig. 2-18-B. 3. In case of the Cassette Guide Post installation, install correctly as the circled section of Fig. 2-18-C. Fig. 2-17-A Fig. 2-17-B Fig. 2-18-A 1 2 1 Clutch Assy Cassette Guide Post Cassette Guide Post Cassette Guide Post Inclined Base T Unit Inclined Base S Unit LED Reflector P4 Cap Cassette Opener P4 Cap Clutch Assy Ring Spring Clutch Lever "A" "B" Coupling Gear Coupling Gear Coupling Spring Clutch Gear Fig. 2-18-B Fig. 2-18-C Screw Torque: 5 ± 0.5kgf•cm [OK] [NG] www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 106 1 2 3 4 1 2 3 4 C D F A B E 7.9 CAUTIONS ON DIASSEMBLING AND ASSEMBLING Screw List Parts Name SCREW, TAP TITE(B) WH7 3*10 CH 1 HEAT SINK 8109I30A0U Num. Used part Parts Code SCREW, TAP TITE(P) WH10 M2.6*8 CH 1 SPRING of DVD FLAP 8110E2680U SCREW, TAP TITE(P) BIND 2.6*8 CH 3 OPERATION PCB 8110022680U SCREW, BIND 3*6 CH 4 ANGLE DVD + LOADER 810223060U SCREW, TAP TITE(S) BIND 3*4 CH 1 TUNER 810723040U SCREW, TAP TITE(B)R PAN 3*29 CH 3 VCR DECK 8109130B9U SCREW, TAP TITE(B) BIND(3D) 3*6 NI 5 CABINET TOP 8109K30601 SCREW, TAP TITE(B) R BIND 3*7 CH 13 1 4 6 2 VCR PCB MPEG PCB ANGLE DVD + BOTTOM ANGLE DVD + SHIELD 810923070U SCREW, TAP TITE(B) BIND 3*8 CH 12 3 4 2 2 POWER PCB 3PIN JACK FAN S-VIDEO 1 OPTICAL JACK 810923080U CORD CONNECTOR, CORD JUMPER List CAUTION Ferrite Core Parts Name CORD CONNECTOR CU2A2701 VCR⇔MPEG 10 wires VCR⇔OPERATION DVD DECK⇔MPEG VCR⇔AC HEAD MPEG⇔VCR MPEG⇔VCR MPEG⇔VCR DVD DECK⇔POWER for DECK Power L=270MM P=2.0MM 10PIN CORD CONNECTOR CU2252802 L=285MM P=2.0MM 5PIN CORD CONNECTOR CU641202 4PIN L=120MM P=2.5MM CORD JUMPER BH040061 L=60MM P=0.5MM H=8MM 40PIN CORD JUMPER 2F061501 6PIN FFC L=150MM CORD JUMPER 2H0I1802 18PIN L=180MM P=1.0MM 06CU2A2701 CD7304 06CU252802 CD651 06CU641202 CD504 12BH040061 CD4001 122F061501 CD102 122H0I1802 CD7303 122H0K1802 CD7301 122H0K1802 CD7302 REF NO. Used part Parts Code CORD JUMPER 2H0K1802 20PIN L=180MM P=1.0MM FFC CORD JUMPER 2H0K1802 20PIN L=180MM P=1.0MM FFC 2. When reattaching the POWER PCB Assy to the Plate bottom, tighten the two screws for the round holes first then tighten the screws for the slotted holes. 1. When reattaching the Front Cabinet, attach the cabinet pressing the Flap of VCR side toward inside. 3. When reattaching the Angle DVD to the DVD deck, tighten the screws for the round holes situated on the rear side first. 4. Insert each flexible cable straight, to avoid loose connection. 5. Be sure to pass the binder through the ferrite core that is attached to the CD7304 (10 wires that connect between MPEG and VCR) and secure and fix both the ferrite core and the CD7304 using the binder. If only the wires are secured but the ferrite core is not, the ferrite core may have movement and become damaged. 6. When attaching the ferrite core to the CD7304, pass the wires through it twice (one wind around it). Incorrect attachment of the ferrite core may compromise its effects of reducing spurious radiation. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 107 5 6 7 8 5 6 7 8 C D F A B E CAUTION (Continued) Cover AC Head Shield 3 Pin Shield Compo 7. Be sure to reattach the Cover AC Head, which is for preventing noise from invading normal audio signals. 8. Be sure to reattach the Shield 3 Pin to the front jack and the Shield Compo to the rear jack of the VCR MT PCB Assy. Those are for preventing electrostatics. 9. Be sure to reattach the Shield 3 Pin so that part of it protrudes from the Plate bottom. Be careful that the Shield 3 Pin is not embedded between the Plate bottom and the circuit board. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 108 1 2 3 4 1 2 3 4 C D F A B E 7.10 KEY TO ABBREVIATIONS A A/C : Audio/Control ACC : Automatic Color Control AE : Audio Erase AFC : Automatic Frequency Control AFT : Automatic Fine Tuning AFT DET : Automatic Fine Tuning Detect AGC : Automatic Gain Control AMP : Amplifier ANT : Antenna A.PB : Audio Playback APC : Automatic Phase Control ASSY : Assembly AT : All Time AUTO : Automatic A/V : Audio/Video B BGP : Burst Gate Pulse BOT : Beginning of Tape BPF : Bandpass Filter BRAKE SOL : Brake Solenoid BUFF : Buffer B/W : Black and White C C : Capacitance, Collector CASE : Cassette CAP : Capstan CARR : Carrier CH : Channel CLK : Clock CLOCK (SY-SE) : Clock (Syscon to Servo) COMB : Combination, Comb Filter CONV : Converter CPM : Capstan Motor CTL : Control CYL : Cylinder CYL-M : Cylinder-Motor CYL SENS : Cylinder-Sensor D DATA (SY-CE) : Data (Syscon to Servo) dB : Decibel DC : Direct Current DD Unit : Direct Drive Motor Unit DEMOD : Demodulator DET : Detector DEV : Deviation E E : Emitter EF : Emitter Follower EMPH : Emphasis ENC : Encoder ENV : Envelope EOT : End of Tape EQ : Equalizer EXT : External F F : Fuse FBC : Feed Back Clamp FE : Full Erase FF : Fast Forward, Flipflop FG : Frequency Generator FL SW : Front Loading Switch FM : Frequency Modulation FSC : Frequency Sub Carrier FWD : Forward G GEN : Generator GND : Ground H H.P.F : High Pass Filter H.SW : Head Switch Hz : Hertz I IC : Integrated Circuit IF : Intermediate Frequency IND : Indicator INV : Inverter K KIL : Killer L L : Left LED : Light Emitting Diode LIMIT AMP : Limiter Amplifier LM, LDM : Loading Motor L LP : Long Play L.P.F : Low Pass Filter LUMI. : Luminance M M : Motor MAX : Maximum MINI : Minimum MIX : Mixer, mixing MM : Monostable Multivibrator MOD : Modulator, Modulation MPX : Multiplexer, Multiplex MS SW : Mecha State Switch N NC : Non Connection NR : Noise Reduction O OSC : Oscillator OPE : Operation P PB : Playback PB CTL : Playback Control PB-C : Playback-Chrominance PB-Y : Playback-Luminance PCB : Printed Circuit Board P. CON : Power Control PD : Phase Detector PG : Pulse Generator P-P : Peak-to Peak R R : Right REC : Recording REC-C : Recording-Chrominance REC-Y : Recording-Luminance REEL BRK : Reel Brake REEL S : Reel Sensor REF : Reference REG : Regulated, Regulator REW : Rewind REV, RVS : Reverse RF : Radio Frequency RMC : Remote Control RY : Relay S S. CLK : Serial Clock S. COM : Sensor Common S. DATA : Serial Data SEG : Segment SEL : Select, Selector SENS : Sensor SER : Search Mode SI : Serial Input SIF : Sound Intermediate Frequency SO : Serial Output SOL : Solenoid SP : Standard Play STB : Serial Strobe SW : Switch SYNC : Synchronization SYNC SEP : Sync Separator, Separation T TR : Transistor TRAC : Tracking TRICK PB : Trick Playback TP : Test Point U UNREG : Unregulated V V : Volt VCO : Voltage Controlled Oscillator VIF : Video Intermediate Frequency VP : Vertical Pulse, Voltage Display V.PB : Video Playback VR : Variable Resistor V.REC : Video Recording VSF : Visual Search Fast Forward VSR : Visual Search Rewind VSS : Voltage Super Source V-SYNC : Vertical-Synchronization VT : Voltage Tuning X X'TAL : Crystal Y Y/C : Luminance/Chrominance www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 109 5 6 7 8 5 6 7 8 C D F A B E 7.11 DISC/CONTENT FORMAT Older models of DVD recorders and DVD writers may reject DVD-RW Ver. 1.2 / 4x discs. If you want to share DVD-RW discs between this recorder and an older recorder/writer, we recommend using Ver. 1.1 discs. Discs which can be played back In this unit, use only discs that meet the standard, such as those bearing the below logo marks on the disc label surface. If you use a non-standard disc, we cannot guarantee playback. Even if such a disc can be played back, we cannot guarantee the image or sound quality. The DVD logo is a registered trademark. * This unit is designed to playback music Compact Discs (CD) that conform to the CD standard. CDs that contain (copy-restriction) signals to protect copyrights cannot be played back. Region management information This unit is designed and manufactured to support the region management information that is recorded on a DVD disc. If the region number written on the DVD disc does not correspond to the region number of this unit, this unit cannot play that disc. • The region number of this unit is “1”. • The unit will play DVD-Video discs marked with labels containing “1” or “ALL”. Example: 1 Media type Logo mark DVD-Video DVD-RW Ver.1.0 Ver.1.1 Ver.1.2 V Ver.1.2CPRM support er.1.1CPRM support DVD-R Ver.2.0 (Ver.2.0/4x/8x) Audio CD* CD-R/CD-RW l Operating DVD-Video • Some operations of DVD-Video may be prohibited by the manufacturer, or some operation methods or functions of the DVD-Video may be different from the description in this manual. • If you attempt an operation that is prohibited by either the disc or the unit, a “ ” mark will appear on the TV monitor. For operations prohibited by the disc, see the information that came with the disc. • When the menu screen or the operation guide appears during disc playback, follow the displayed information. Discs which cannot be played back The discs listed below cannot be played back in general. Even if one of these can be played back, it may not be played back correctly. If a disc is played back by mistake, extensively loud sounds may blow the speakers or may damage the hearing of those in hearing range. Do not playback the discs listed below. CDG, Photo-CD, CD-ROM, CD-TEXT,CD-EXTRA, VCD, SVCD, SACD, PD, CDV, DVD-ROM, DVD-RAM, DVD+R/RW, DVD audio, etc. The below DVD-Video may not be played back. • DVD-Video that do not have the region number “1” or “ALL”. • PAL or SECAM DVD-Video. • Prohibited or business-use DVD-Video. CD-R/CD-RWs cannot be played back for the following reasons. • Compatibility of the disc and this unit. • Compatibility of the disc and the recorder used. • Unfinalized discs. Do not playback the following discs. Playback of these discs may cause a failure. • Discs on which paper, labels or stickers are affixed. • Discs that have sticky areas left by adhesive tape. • Special-shaped discs. PC-created disc compatibility Discs recorded using a personal computer may not be playable in this unit due to the setting of the application software used to create the disc. In these particular instances, check with the software publisher for more detailed information. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 110 1 2 3 4 1 2 3 4 C D F A B E Discs on which video can be recorded To record video with this unit, use the discs below: Media type Logo mark DVD-RW Ver.1.0 Ver.1.1 Ver.1.2 Ver.1.1CPRM support DVD-R Ver.2.0 (Ver.2.0 /4x /8x) DVD-RW • The disc can be erased and used again about 1,000 times. • Only the VR mode can be used for Ver.1.0 discs. • With Ver.1.1/1.2 discs, you can record by selecting the VR mode or Video mode. • When you record in the VR mode, you can repeatedly record and erase. By erasing unnecessary titles, you effectively increase remaining time. • When you record in the Video mode, you can record until the disc becomes full. • When you use the Video mode, you can newly record on the disc by formatting the disc. However, if the disc is formatted, all the recorded contents will be erased. DVD-R • You can record on the disc only in the Video mode. • You can record until the disc becomes full. • Finalizing the discs allows playback on other DVD players. However, the finalized discs can no longer be recorded. • Discs can be recorded to repeatedly until they are finalized. Note • There are some players that cannot playback discs that were recorded with this unit. We cannot guarantee the playback with other units. • This unit cannot record on DVD-R and DVD-RW discs that are 8 cm in diameter. • This unit cannot record on CD-R or CD-RW. Recording format This unit has two modes for formatting discs for recording: VR mode and Video mode. When a blank, new disc is loaded into this unit, the automatic format function starts to format the disc. (For the disc format setting in this step.) VR mode • This mode can be used for DVD-RW. • In this mode, the discs can be recorded and edited repeatedly. • The disc recorded in this mode can be played back with other DVD -RW-compatible players. • When a Ver.1.1 CPRM or Ver .1.2 CPRM disc is used, you can record a “Copy Once ” program. Video mode • This mode can be used for DVD-R and DVD-RW (Ver.1.1/1.2). • When you finalize the disc after recording, the disc recorded with this unit can be played back with other DVD players. • Recording, editing or playback of an unfinalized disc can be done only with this unit. However, there is some limitation to editing operations. • In this mode, you cannot record a “Copy Once” program. • When you record a TV program of a bilingual broadcast, only one of the audio modes can be recorded. You have to select it. Format modes that can be used each disc The usable format depends on the media type as shown in the below table. Media type Format DVD-RW Ver.1.0 DVD-RW Ver.1.1 and 1.2 DVD-R Ver.2.0 (Ver.2.0/4x/8x) Available functions VR mode VR mode Video mode Video mode Playback, recording and editing (Original/playlist) Playback, recording and editing (Original/playlist) Playback and recording Editing (with limitation) Playback and recording Editing (with limitation) Ver.1.2CPRM support www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 111 5 6 7 8 5 6 7 8 C D F A B E 7.12 CLEANING Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 Position to be cleaned Cleaning tools Fans Cleaning paper : GED-008 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 112 1 2 3 4 1 2 3 4 C D F A B E 8. PANEL FACILITIES 8.1 FRONT AND REAR SECTION FF (Fast Forward) button REW (Rewind) button DVD/VCR common AUDIO (L/R)/VIDEO IN (LINE 2) jacks VCR/DVD button STANDBY/ON button VCR EJECT button Disc tray REC button PLAY button Cassette Loading Slot IR Remote senser OPEN/CLOSE button DVD S-VIDEO IN (LINE 2) jack STOP button DVD indicator VCR indicator CHANNEL -/+ buttons Display window Rear panel AC power cord FAN Make sure that when installed the fan is not obstructed. DVD COAXIAL DIGITAL AUDIO OUT jack DVD/VCR common AUDIO (L/R)/VIDEO OUT jacks DVD AUDIO (L/R) OUT jacks DVD/VCR common AUDIO (L/R)/VIDEO IN (LINE 1) jacks DVD S-VIDEO IN (LINE 1) jack DVD S-VIDEO OUT jack DVD COMPONENT OUT jacks DVD OPTICAL DIGITAL AUDIO OUT jack RF IN jack RF OUT jack Front panel www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 113 5 6 7 8 5 6 7 8 C D F A B E 8.2 DISPLAY Display window P 2 1 3 4 No. Display Description Lights during video tape playback. 1 Video tape is temporarily stopped. Lights during video tape recording. Progressive scanning mode. Timer recording display. P 2 4 Appears when a CD is inserted. Appears when a CD-R is inserted. Appears when a DVD-Video is inserted. Appears when a DVD-R is inserted. Appears when a DVD-RW is inserted. Appears when a DVD-RW in VR mode is inserted. When the disc is set to video mode, VR does not appear. . Appears when the tuner built into this unit is selected. When you press TV/VCR, VCR disappears. Video tape is in the unit. Clock display (Colon [ : ] flashes). Counter display in hour/minute/second for VCR/DVD, minute/second for CD. CATV channel display. TV channel display.. Track number display for CD. Display for afternoon (out in the morning). The external input channel (L1 or L2) display. Error display. Lights during playback of DVD and CD. Flashes in auto resume. DVD or CD is temporarily stopped. Lights during DVD recording. CD CD-R DVD DVD-R DVD-RW VR VCR 10:00 01H00M00S C 36CH 2CH TRK 002 PM L1/L2 Err 3 4 DVD recording modes. XP, SP, LP or SLP is selected in turn by pressing the REC MODE/SPEED repeatedly. . 2 VCR recording modes. SP or SLP is selected in turn by pressing the REC MODE/SPEED repeatedly. SP/SLP XP/SP/LP/SLP Appears when a CD-RW is inserted. CD-RW Note • Some discs may not playback correctly, or chapter number, playback time, etc may not be displayed. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 114 1 2 3 4 1 2 3 4 C D F A B E 8.3 REMOTE CONTROL Remote control 1 STANDBY/ON Turns power on/off. 2 VCR EJECT Ejects the cassette tapes. 3 DVD OPEN/CLOSE Opens or closes the tray. 4 DVD/VCR Switches to operation between VCR and DVD. 5 0-9 Use for direct TV channel selection of TV; setting the input entering a password ; entering a Pluscode for VCR Plus+ timer programming. 6 TIMER REC Sets the unit to start recording at a preset time. 7 INPUT SELECT Switches between the external inputs. 8 VCR Plus+ Display the VCR Plus+ program screen. 9 RETURN Closes the menu window. 10 CLEAR/CANCEL Cancels input data in the setting mode ; deletes the timer recording program . 11 TITLE MENU/TOP MENU Selects titles of a DVD disc. 12 CH +/– Use to select TV channels. Up/down cursor buttons 13 TRK +/– Use to adjust the VCR manual playback tracking. Left/right cursor buttons 14 ENTER/SELECT Use to select menu options. 15 DVD MENU Displays the menu of the DVD disc. 16 SETUP Displays the setup menu. 17 STOP Stops playback or recording. 18 PLAY Starts playback. 19 PAUSE/STILL Pauses recording or playback (press again to restart). 20 SKIP / Skips forward or back chapters. 21 INDEX – / + Searches for INDEX marks on a tape 22 REW/SEARCH – Rewind/review playback 23 F.FWD/SEARCH + Fast forward/forward search playback 24 ONE TOUCH REPEAT Repeats playback of the last 10 seconds of video. 25 CM SKIP Skips commercial breaks. 26 SLOW Starts slow motion playback. 27 REC Starts recording. 28 REC MODE/SPEED Selects the recording mode. 29 DUBBING Copies VCR to DVD or DVD to VCR. 30 AUDIO/AUDIO SELECT Switches sound between mono and stereo ; changes the language of the DVD. 31 DISPLAY/CALL Displays VCR or DVD operation status. 32 ZOOM 33 REPEAT A-B Repeats playback between A and B. 34 ZERO RETURN Stops the tape when the counter reaches 00H00M00S. 35 COUNTER RESET Resets the counter to 00H00M00S. 36 ANGLE Changes the DVD playback angle. 37 SUBTITLE Selects subtitles of the DVD disc. 38 ATR Digital auto tracking for VCR playback. 39 PLAY MODE Selects the playback mode. 40 REPEAT Selects the repeat playback mode. 41 CLOCK/COUNTER Changes the front panel display mode. 42 TV/VCR Switches input between the TV and VCR. 43 PROGRESSIVE Activates the progressive scanning mode. 4 ¢ 4 ¢ 3 3 / / 3 3 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 115 5 6 7 8 5 6 7 8 C D F A B E www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DVR-RT500-S 116 1 2 3 4 1 2 3 4 C D F A B E VHS Alignment Tape GGV1183 VHS Alignment Tape GGV1184 Hi-Fi Audio (For 4 heads mode) Name Jig No. Remarks X Value Adjustment (For 4 heads mode) VHS Alignment Tape GGV1185 EP Monoscope, 6kHz (For 4 heads mode) Adapter GGF1506 Dial Torque Gauge (10-90 gf•cm) GGF1507 VSR Torque, Brake Torque (S Reel/T Reel Assy) Brake Torque (T Reel Assy) Dial Torque Gauge (60-600 gf•cm) GGF1508 VSR Torque, Brake Torque (S Reel) Post Adjustment Screwdriver GGF1509 X Value Adjustment Screwdriver GGF1510 Guide Roller Adjustment X Value Adjustment Mater Plane GGF1511 Reel Disk Height Adjustment Reel Disk Height Adjustment Jig GGF1512 Torque Tape (VHT-063) GGV1186 Reel Disk Height Adjustment Playback Torque, Back Tension Torque During Palyback 7 Jigs list www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com