ORDER NO. PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2010 DEH-1300MP/XNUC CRT4588 CD RECEIVER DEH-1300MP/XNUC DEH-1350MP/XNES DEH-1350MP/XNES1 DEH-1350MPG/XNES DEH-1350MP/XNCN5 DEH-1390MP/XNID This service manual should be used together with the following manual(s): Model No. Order No. Mech. Module Remarks CX-3269 CRT4488 S11.1COMP CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly For details, refer to "Important Check Points for Good Servicing". K-ZZZ. JULY 2010 Printed in Japan www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 2 1 2 3 4 1 2 3 4 C D F A B E SAFETY INFORMATION CAUTION Where in a manufacturer’s service documentation, for example in circuit diagrams or lists of components, a symbol is used to indicate that a specific component shall be replaced only by the component specified in that documentation for safety reasons, the following symbol shall be used: This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. - Safety Precautions for those who Service this Unit. When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable results. Caution: 1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept. 2. During repair or tests, do not view laser beam for 10 seconds or longer. WARNING This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive harm. Health & Safety Code Section 25249.6 - Proposition 65 CAUTION This product is a class 1 laser product classi- fied under the Safety of laser products, IEC 60825-1:2007, and contains a class 1M laser module. To ensure continued safety, do not re- move any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel. CAUTION—CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN, DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. WARNING! The AEL (accessible emission level )of the laser power output is less than CLASS 1 but the laser component is capable of emitting radiation exceeding the limit for CLASS 1. A specially instructed person should do servicing operation of the apparatus. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 3 5 6 7 8 5 6 7 8 C D F A B E CAUTION Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacture. Discord used batteries according to the manufacture's instructions. Laser diode characteristics Wave length : 785 nm to 814 nm Maximum output : 1 190 µW(Emitting period : unlimited) Additional Laser Caution Transistors Q101 in PCB drive the laser diodes. When Q101 is shorted between their terminals, the laser diodes will radiate beam. If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 4 1 2 3 4 1 2 3 4 C D F A B E [Important Check Points for Good Servicing] In this manual, procedures that must be performed during repairs are marked with the below symbol. Please be sure to confirm and follow these procedures. 1. Product safety Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual. 1 Use specified parts for repair. Use genuine parts. Be sure to use important parts for safety. 2 Do not perform modifications without proper instructions. Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise. 3 Make sure the soldering of repaired locations is properly performed. When you solder while repairing, please be sure that there are no cold solder and other debris. Soldering should be finished with the proper quantity. (Refer to the example) 4 Make sure the screws are tightly fastened. Please be sure that all screws are fastened, and that there are no loose screws. 5 Make sure each connectors are correctly inserted. Please be sure that all connectors are inserted, and that there are no imperfect insertion. 6 Make sure the wiring cables are set to their original state. Please replace the wiring and cables to the original state after repairs. In addition, be sure that there are no pinched wires, etc. 7 Make sure screws and soldering scraps do not remain inside the product. Please check that neither solder debris nor screws remain inside the product. 8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord. Damaged power cords may lead to fire accidents, so please be sure that there are no damages. If you find a damaged power cord, please exchange it with a suitable one. 9 There should be no spark traces or similar marks on the power plug. When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary. a Safe environment should be secured during servicing. When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely. 2. Adjustments To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification. Adjustments should be performed in accordance with the procedures/instructions described in this manual. 4. Cleaning For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances. 3. Lubricants, Glues, and Replacement parts Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied. 5. Shipping mode and Shipping screws To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 5 5 6 7 8 5 6 7 8 C D F A B E CONTENTS SAFETY INFORMATION .....................................................................................................................................2 1. SERVICE PRECAUTIONS................................................................................................................................6 1.1 SERVICE PRECAUTIONS.........................................................................................................................6 1.2 NOTES ON SOLDERING...........................................................................................................................7 2. SPECIFICATIONS.............................................................................................................................................8 2.1 SPECIFICATIONS......................................................................................................................................8 2.2 DISC/CONTENT FORMAT.......................................................................................................................10 2.3 PANEL FACILITIES ..................................................................................................................................11 2.4 CONNECTION DIAGRAM........................................................................................................................12 3. BASIC ITEMS FOR SERVICE ........................................................................................................................13 3.1 CHECK POINTS AFTER SERVICING .....................................................................................................13 3.2 PCB LOCATIONS.....................................................................................................................................14 3.3 JIGS LIST .................................................................................................................................................15 3.4 CLEANING ...............................................................................................................................................15 4. BLOCK DIAGRAM ..........................................................................................................................................16 4.1 BLOCK DIAGRAM....................................................................................................................................16 4.2 LCD...........................................................................................................................................................18 5. DIAGNOSIS ....................................................................................................................................................19 5.1 OPERATIONAL FLOWCHART.................................................................................................................19 5.2 ERROR CODE LIST.................................................................................................................................20 5.3 CONNECTOR FUNCTION DESCRIPTION .............................................................................................22 6. SERVICE MODE.............................................................................................................................................23 6.1 DISPLAY TEST MODE.............................................................................................................................23 6.2 CD TEST MODE.......................................................................................................................................26 7. DISASSEMBLY...............................................................................................................................................27 8. EACH SETTING AND ADJUSTMENT............................................................................................................34 8.1 CD ADJUSTMENT ...................................................................................................................................34 8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT ....................................................35 8.3 PCL OUTPUT CONFIRMATION ..............................................................................................................37 9. EXPLODED VIEWS AND PARTS LIST ..........................................................................................................38 9.1 PACKING..................................................................................................................................................38 9.2 EXTERIOR ...............................................................................................................................................40 9.3 CD MECHANISM MODULE .....................................................................................................................42 10. SCHEMATIC DIAGRAM................................................................................................................................44 10.1 TUNER AMP UNIT(GUIDE PAGE).........................................................................................................44 10.2 KEYBOARD UNIT ..................................................................................................................................50 10.3 CD MECHANISM MODULE(GUIDE PAGE)...........................................................................................52 10.4 WAVEFORMS.........................................................................................................................................58 11. PCB CONNECTION DIAGRAM ....................................................................................................................60 11.1 TUNER AMP UNIT .................................................................................................................................60 11.2 KEYBOARD UNIT...................................................................................................................................64 11.3 CD CORE UNIT(S11.1COMP)................................................................................................................66 12. ELECTRICAL PARTS LIST...........................................................................................................................68 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 6 1 2 3 4 1 2 3 4 C D F A B E 1. SERVICE PRECAUTIONS 1.1 SERVICE PRECAUTIONS 1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual. 2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during power-on mode may damage the ICs inside the unit. 3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment (shorting-solder) by referring to "the DISASSEMBLY". 4. After replacing the pickup unit, be sure to check the grating. 5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction. 6. area and a heat sink becomes hot areas. Be careful not to burn yourself. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 7 5 6 7 8 5 6 7 8 C D F A B E 1.2 NOTES ON SOLDERING For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering. Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C. Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron. Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 8 1 2 3 4 1 2 3 4 C D F A B E 2. SPECIFICATIONS 2.1 SPECIFICATIONS www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 9 5 6 7 8 5 6 7 8 C D F A B E www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 10 1 2 3 4 1 2 3 4 C D F A B E 2.2 DISC/CONTENT FORMAT www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 11 5 6 7 8 5 6 7 8 C D F A B E 2.3 PANEL FACILITIES www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 12 1 2 3 4 1 2 3 4 C D F A B E 2.4 CONNECTION DIAGRAM www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 13 5 6 7 8 5 6 7 8 C D F A B E 3. BASIC ITEMS FOR SERVICE 3.1 CHECK POINTS AFTER SERVICING To keep the product quality after servicing, please confirm following check points. d e m rif n o c e b o t m e tI s e r u d e c o r P . o N 1 Confirm whether the customer complain has been solved. If the customer complain occurs with the specific media, use it for the operation check. The customer complain must not be reappeared. Display, audio and operations must be normal. 2 CD Play back a CD. (Track search) No malfunction on display, audio and operation. 3 FM/AM tuner Check FM/AM tuner action. (Seek, Preset) Switch band to check both FM and AM. Display, audio and operations must be normal. 4 Check whether no disc is inside the product. The media used for the operating check must be ejected. r e tf a e c n a r a e p p a sti n o trid r o s e h ct a r c s o N k c e h c e c n a r a e p p A 5 receiving it for service. See the table below for the items to be checked regarding audio: Item to be checked regarding audio Distortion Noise Volume too low Volume too high Volume fluctuating Sound interrupted www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 14 1 2 3 4 1 2 3 4 C D F A B E 3.2 PCB LOCATIONS A B Keyboard Unit CD Core Unit (S11.1Comp) C Tuner Amp Unit A : DEH-1300MP/XNUC B : DEH-1350MP/XNES C : DEH-1350MP/XNES1 D : DEH-1350MPG/XNES E : DEH-1350MP/XNCN5 F : DEH-1390MP/XNID Unit Number : QWM3162(A) : QWM3163(B,C,D,F) : QWM3164(E) Unit Name : Tuner Amp Unit Unit Number : Unit Name : Keyboard Unit Unit Number : CWX3957 Unit Name : CD CORE UNIT(S11.1Comp) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 15 5 6 7 8 5 6 7 8 C D F A B E 3.3 JIGS LIST 3.4 CLEANING - Jigs List - Grease List Name Grease Grease Grease No. GEM1024 GEM1045 Remarks CD Mechanism Module CD Mechanism Module Name Grease No. Remarks Name 15P FFC Test Disc L.P.F. Jig No. GGD1177 TCD-782 Remarks Tuner Amp Unit - CD Core Unit Checking the grating Checking the grating (Two pieces) Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 16 1 2 3 4 1 2 3 4 C D F A B E 4. BLOCK DIAGRAM 4.1 BLOCK DIAGRAM IN2_L IN1_L 2 TUNL 1 JA401 1 2,3 CN701 VCK, VDT, VST LOUT SYS+B ANTENNA IFA IFB 3 VDD3V 7 SWVDD3V SW5V 6 5 BSENS SYSPW PWROFF 2 1 36 47 15 SWVDD 4 1 BRST,BRXEN,BSRQ,BDATA,BSCK CDRESET 8 RESET 16 SL-IN REFA REFB LDET SWVDD3V DI CK CE1 DO CE2 SLOUT CD-Lch 3 B.UP 10 9 VDD3V SYS+B SWVDD VDD SW5V SYS+B BSENS SW5VCONT +B +BUP VDDCONT SYSTEM 8 7 DREG 85 SWVDD3V Q602 PLL_VDD M-REGC 55 9 57 DVDD2 94 DVDD4 121 B.UP Q751 14 15 Q752 VDCONT 126 CD VD VD VDD A ELECTRONIC SOURCE SE IC20 PML01 SYSTEM M COMPU (2/2 IC60 PN504 REGULATOR IC IC911 BA49181-V12 DVDD3 TUNER AMP UNIT CD CORE UNIT(S11.1 COMP) BRST,BRXEN,BSRQ M LD MD SPINDLE M LOADING/CARRIAGE LD- MD 15 5 HOLOGRAM RF AMP, CD DECODER, MP3&WMA DECODER 2 VD VD 13 LOUT 9 16 VO3- 15 VO3+ 18 VO4- 17 VO4+ 21 CNT 55 LOUT 9 MUTE TD,FD AC,BD,E,F SD,MD LD+ 14 141 LD 142 PD CONT CLCONT HOME 9 20 41 VDD 1 VDD BDATA,BSCK VDD 15 5 FOCUS ACT. TRACKING ACT. FOP TOP 2 1 TOP FOP 11 VO1- 14 VO2+ 2 1 14 DSCSNS 10 16 RESET 8 RESET 8 8 VREF REFOUT 133 REFOUT 3 3 FOM FOM 12 VO1+ 4 4 TOM TOM 13 VO2- 22 LDIN LOEJ 28 VDSENS 11 VD 39 PUEN VCC VDD UNIT MOTOR MOTOR ACTUATOR/ MOTOR DRIVER BA5839FP HOME DSCSNS PE5746A DIGITAL SERVO/DATA • PROCESSOR CPU CN701 Q101 CN101 Q102 IC301 S901 S903 IC201 C VCC 12 12 VCC PD VREF LD+ SOP SOM LCOP LCOM PICKUP UNIT (P10.5)(SERVICE) FM/AM TUNER UNIT ATT ATT ATT RF LFP LFP VCO CF IC1 IC901 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 20 11 ANT VCC SLIN IFOUTA IFOUTB DGND REFINA REFINB LDET VDD DI CK CE1 DO CE2 SLOUT RFGND1 RFGND2 RFGND3 RFGND4 TANK EEPROM MIX / IF / PLL www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 17 5 6 7 8 5 6 7 8 C D F A B E SYS+B IN2_L IN1_L 2 UNL 1 7 Rear_L B.UP 35 44 MUTE 9 7 3 5 FL- FL+ RL- RL+ FL- FL+ RL- RL+ BREM ACC GND 22 Q921 MUTE CN801 VCK, VDT, VST B.UP Q803 ASENS 13 7 5 1 3 18 16 JA901 7 4 3 6 ROT1 ILM+B KYDT DPDT 111 ILMPW 2 DPDT/SELFDO 24 KEYDT/SELFDI 23 JA251 RLIn 12 ROT1 5 ROT0 110 ROT0 Q802 14 DSENS DSENS 34 6 Front_L FLIn 11 Q251 MUTE 25 B.REM ASENS RL 14 BSENS SYSPW PWROFF 36 47 15 SWVDD 1 CDRESET 16 SL62 62 SL-IN IF_INA 77 IFA IF_INB 78 IFB FREFA 96 REFA FREFB 97 REFB LOCK 99 LDET TUNDI 100 DI TUNCK 101 CK TUNDO 102 CE1 CE2 CE 103 DO SL 109 CE2 136 SLOUT RCA OUT L_OUT 59 D-Lch B.UP 12 SW5V 10 AUX L 13 AUXL 4 IN4+_L ILMPW DREG 85 SWVDD3V PLL_VDD M-REGC 55 9 57 DVDD2 94 DVDD4 121 VDCONT 126 SYSTEM MICRO COMPUTER (1/2) IC601 ELECTRONIC VOLUME/ SOURCE SELECTOR IC201 PML014B PN5043A SYSTEM MICRO COMPUTER (2/2) IC601 PN5043A POWER CONNECTOR AMP IC301 PAL007E Q351 (2/2) Q351 (1/2) DVDD3 SOURCE 33 SRC 3 1 P251 RCAG VCC VCC 20 6 B.UP STBY 4 LCD DRIVER/ KEY CONTROLLER IC1801 DSEN DPDT KYDT V1801 CN1801 JA1801 4 18 20 DPDT KYDT SWVDD 6 S1824 56 VLCD VDD 14 5 3 1 2 4 3 7 12 AUX L 13 AUXL AUXR AUXG ROT1 ROT0 2 3 1 ILM+B ILLUMI KEYBOARD UNIT B FRONT AUX PD6340A SW5V 10 KEY MATRIX KDT0-3,KST0-4 SRC 5 10 SOURCE LCD REMOTE CONTROL SENSOR 1 3 IC1802 GP1UXC14RK 17 REM www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 18 1 2 3 4 1 2 3 4 C D F A B E 4.2 LCD COMMON SEGMENT LCD(CAW2008) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 19 5 6 7 8 5 6 7 8 C D F A B E 5. DIAGNOSIS 5.1 OPERATIONAL FLOWCHART VDD = 5 V Pin 8 BSENS Pin 36 ASENS Pin 35 DSENS Pin 34 BSENS = L DSENS = L Starts communication with Grille microcomputer. SWVDD <- H Pin 1 Source keys operative Source ON SYSPW <- H Pin 15 300 m 300 m In case of the above signal, the communication with Grille microcomputer may fail. If the time interval is not 300 msec, the oscillator may be defective. Completes power-on operation. (After that, proceed to each source operation) Power ON ASENS = L www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 20 1 2 3 4 1 2 3 4 C D F A B E 5.2 ERROR CODE LIST CD error code list (Error mode 0xFD) Error codes When the CD drive does not work or stops during operation due to an error, the CD drive enters the Error mode and displays the causes of the error by number. This is intended to reduce nonsense calls from users and supplement the analysis and repair performed by service members. Basic displaying means When the CD MODE (CD mode display area) displays ERROR (0xFD), an error code is written in MIN (minute display area) and SEC (second display area). Same data is written in MIN and SEC. TNO is blank (#0FFH) as usual. Head unit display examples The following are displayed according to the display capability of the LCD. xx stands for an error code. *For OEM products, errors are displayed as per specifications of the OEM client Code Category Error Details and causes 10 Servo Carriage home error Cause: HOME switch failure or carriage movement failure Details: The pickup cannot move to the inner circumference or it cannot move from the inner circumference to the outer circumference. 11 Servo Focus error Causes: Disc is inserted upside down, disc is dirty or vibrated, etc. Details: Out of focus 12 Servo Spindle lock error Causes: Spindle error, disc is damaged, dirty, vibrated or contains no data, Sub-code error RF signal error, etc. RF amplifier error Details: The spindle rotation speed is unstable, sub-code is unreadable, etc. 15 Servo RF error Cause: CD R/RW disc contains no data. Details: Digital signals from disc cannot be detected. 17 Servo Setup error Causes: Disc is damaged, dirty, vibrated, etc. Details: Laser output cannot be adjusted, focus is unstable, etc. 22 Disc Impossible to play There is no playable MP3 file or WMA file. -> The set CD-ROM disc did not contain any MP3 file or WMA file. 23 Disc File format error The data was written in noncompliant file format. -> A CD-ROM containing data recorded in a file format other than ISO9660 Level-1 or 2 (such as UDF) was set. 24 Disc All DRM All the playable files in the disc are the DRM files. -> This error will not occur if there is any non-DRM file. 30 Servo Search time-out Cause: Carriage or tracking failure, disc is damaged or dirty, etc. Details: This error indicates that a target address could not be reached and the search time has run out. This error occurs after the search mode changes to the SETUP mode. 50 Mecha Ejection error Cause: Loading or ejection failure Details: This error occurs when loading or ejection has failed and ended in the middle (before completion of loading or ejection). 51 Mecha Ejection rotation retrial Cause: Ejection rotation retrial failure error Details: This error occurs when automatic loading was successful after ejection rotation retrial has failed (twice). 52 Mecha Disc loading error Cause: Disc loading cannot be completed. -> Foreign substances were inserted. Disc was caught. 8-digit display 6-digit display 4-digit display ERROR-xx ERR-xx E-xx www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 21 5 6 7 8 5 6 7 8 C D F A B E Error code list of CD power supply (Error mode 0xFB) *When determining a power supply error, please refer to the error mode (0xFB) only. (You do not have to refer to the Error code 0xA0.) Errors are not displayed for the individual mecha unit (since CD is turned off at mecha error). When TOC cannot be read, it is not recognized as an error but the operation is continued accordingly. When designing a new head unit, be sure to follow the display examples. The higher digit of error codes indicates a major category as shown below. The following shows how to recover from each error. Servo-related errors (1x, 2x, 3x): CD OFF, EJECT, ACC OFF, Back-up OFF, COMMUNICATION RESET, RESET Loading-related and ejection-related errors (50, 52): RELOAD, EJECT, ACC OFF, Back-up OFF, COMMUNICATION RESET, RESET Ejection rotation retrial errors (51): CD ON, EJECT, ACC OFF, Back-up OFF, COMMUNICATION RESET, RESET Remarks Code Category Error Details and causes Code Category 1x Servo-related errors 2x TOC lead-related 3x Servo-related errors 5x Mecha-related errors A0 System Power supply error The power (VD) is short-circuited to a higher potential point or a lower potential height. -> SW transistor failure or power supply error (connector failure). EJECT does not work. The error state can be recovered only by turning off and on the ACC. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 22 1 2 3 4 1 2 3 4 C D F A B E 5.3 CONNECTOR FUNCTION DESCRIPTION REAR OUTPUT ANTENNA 1 FL+ 2 FR+ 3 FL- 4 FR- 5 RL+ 6 RR+ 7 RL- 8 RR- 9 NC 10 NC 11 NC 12 NC 13 ACC 14 B.REM 15 B.UP 16 GND 16 14 12 10 8 6 4 2 15 13 11 9 7 5 3 1 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 23 5 6 7 8 5 6 7 8 C D F A B E 6. SERVICE MODE 6.1 DISPLAY TEST MODE Display test mode (1)/(2) confirm ROM correction information and the lighting of all segments of a LCD display. [To operate] Display test mode (1) [Operation key] [Restriction in operating and displaying display test mode (1)] Display test mode (1) is to be operated or displayed only under the condition that all sources are off. -> After a short press of "SOURCE" key turns some sources on, or a long press of "SOURCE" key leads to the status of default menu, key actions associated with sources which are on, or those associated with default menu are performed. As a result, display test mode (1) cannot be displayed properly in some cases. [Test items] Start display test mode (1). (Press “LEFT” and “DOWN” keys simultaneously to start resetting.) The lighting of all segments is turned on. Press “LEFT” + “DOWN” keys The lighting of all segments including icons is turned on. Press “AUDIO” key Color of key illumination : Lit in a color set as an initial value or a setting valuein the default menu. Press “FUNCTION” key Icons : All lit. Press “ ” key Press “ ” key The lighting of all segments is turned off. The lighting of all segments including icons is turned off. LED lighting of keys is turned off. Color of key illumination : Off Icons : All off LCD check mode A (horizontal lines) Color of key illumination : Lit in a color set as an initial value for single illumination. Lit in a changed color for dual illumination. Icons *Only 14-seg display is lit. Valid only during display test mode (1) Valid only during display test mode (1) AUDIO Transition to “The lighting of all segments is turned off” FUNCTION Transition to LCD check mode A (horizontal lines) Transition to LCD check mode B (oblique lines) Transition to LCD check mode C (vertical lines) Valid only during display test mode (1) Remarks Transition to “The lighting of all segments is turned on” is valid only during display test mode (1) Valid only during display test mode (1) Operation Key Processing LEFT + DOWN Enter display test mode (1) Transition to “The lighting of all segments is turned on” A B C D E A B C D E A B C A B C D E : All off Press “LEFT” + “DOWN” keys Press “AUDIO” key Press “FUNCTION” key Press “ ” key Press “ ” key Press “LEFT” + “DOWN” keys Press “AUDIO” key Press “FUNCTION” key Press “ ” key Press “ ” key Press “LEFT” and “DOWN” keys simultaneously to start resetting. Then, perform the following key operation. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 24 1 2 3 4 1 2 3 4 C D F A B E A B C D E A B C D E D E [To operate] Display test mode (2) Press “ ” and “ ” keys simultaneously to start resetting. Then, perform the following key operation. [Operation key] [Test items] Start display test mode. (Press “ ” + “ ” keys simultaneously to start resetting.) * Initial condition Turn on sources except AUX.(Hold down “SOURCE” key.) Usual update of display Product operation is performed as usual, in appearance. Switch to "The lighting of all segments is turned on" by pressing “ ” + “ ” keys simultaneously. The lighting of all segments is turned on. The lighting of all segments including icons is turned on. Switch to "Usual update of display" by pressing “ ” + “ ” keys simultaneously. All on On (an initial value) On (lighting condition of normal times) On (an initial value or setting value of default menu) On (lighting condition of normal times) On (an initial value or setting value of default menu) Off All off Remarks Key Illumination Operation key Processing Icon Enter display test mode (2) Switch to next test mode LCD check mode B (oblique lines) Color of key illumination : Lit in a color set as an initial value. Icons *Only 14-seg display is lit. : All off Press “LEFT” + “DOWN” keys Press “AUDIO” key Press “FUNCTION” key Press “ ” key Press “ ” key LCD check mode C (vertical lines) Color of key illumination : Lit in a color set as an initial value. Icons *Only 14-seg display is lit. : All off Press “LEFT” + “DOWN” keys Press “AUDIO” key Press “FUNCTION” key Press “ ” key Press “ ” key www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 25 5 6 7 8 5 6 7 8 C D F A B E [Test items] Start display test mode. (Press " " + " " keys simultaneously to start resetting.) * Initial condition Turn on AUX source. (Hold down "SOURCE" key) ROM correction information is displayed. When ROM correction is not connected. N O R O M C When check sum error of ROM correction occurs. S U M E R R When ROM correction is connected and active. S1S2S3S4C4C3C2C1 Sn ROM correction unique information (model number) Cn ROM correction status of each channel (1-4) 0: Not in use (operable) 1: In use (inoperable) Switch to "The lighting of all segments is turned on" by pressing " " + " " keys simultaneously. The lighting of all segments is turned on. The lighting of all segments including icons is turned on. Switch to "ROM correction information is displayed" by pressing " " + " " keys simultaneously. On (an initial value or setting value of default menu) All off On (an initial value or setting value of default menu) All on Off All off On (lighting condition of normal times) On (an initial value) Key Illumination Icon www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 26 1 2 3 4 1 2 3 4 C D F A B E 6.2 CD TEST MODE [BAND] Power On/Off [>] CRG + / TR Jump + (Direction Of the external surface) [<] CRG - / TR Jump - (Direction Of the internal surface) [1] T.CLS & AGC & Applicable servomechanism / AGC,AGC display setting [2] RF Gain switching / Offset adjustment display / T.Balance adjustment / T.Open [3] Close,S.Curve / Rough Servo and RF AGC / F,T,RF AGC [4] SPDL 1X/2X switchingAs for the double speed (2x), audio output cannot be supported. [5] Error Rate measurementON : ERR 30Counts Start BER display data[%] [6] F. Mode switching / Tracking Close / CRG • TR Jump Switching [Key] Operation Test Mode - Flow Chart [BAND] Power On (T.Offset is adjusted) TRK MIN SEC 00 00 00 [3] Focus Close S curve check TRK MIN SEC 91 91 91 [6] Focus Mode switching TRK MIN SEC 0X 0X 0X [1] Tracking Searvo Close 00 00 00 or 99 99 99 [2] Self-adjusting switching TRK MIN SEC ?? ?? ?? [2] T.Balance adjustment/ T.BAL coefficient display TRK MIN SEC ?? ?? ?? [2] Tracking Open 8X 8X 8X or 9X 9X 9X [5] Gop Mode Gop Mode switching TRK MIN SEC OL OL OL 00 00 00 or 99 99 99 [BAND] Power Off TRK MIN SEC [1] T.Close & AGC Applicable servomechanism TRK MIN SEC ?tr ?min ?sec [6] T.Close Applicable servomechanism TRK MIN SEC ?tr ?min ?sec [3] RF AGC / RF AGC coefficient display TRK MIN SEC ?? ?? ?? [BAND] Power Off TRK MIN SEC [1] F,T,RF AGC F.Bias display switching TRK MIN SEC ?? ?? ?? [3] F,T AGC / F.Bias RF AGC TRK MIN SEC ?tr ?min ?sec [6] CRG / TR Jump switching TRK MIN SEC ?tr ?min ?sec [BAND] Power Off TRK MIN SEC [BAND] Power Off TRK MIN SEC [3] Power On (T.Offset is not adjusted) TRK MIN SEC 99 99 99 [2] RF AMP *1 *9 *8 *8 *4 *6 *4 *5 *7 *3 *10 *2 Gain switching TRK MIN SEC GG GG GG [4] SPINDLE Speed switching TRK MIN SEC SP SP SP [>] CRG + 00 00 00 or 99 99 99 [<] CRG - 8X 8X 8X or 9X 9X 9X [>] CRG + 8X 8X 8X or 9X 9X 9X [<] CRG - TRK MIN SEC ?tr ?min ?sec [>] CRG/TR Jump + TRK MIN SEC ?tr ?min ?sec [<] CRG/TR Jump - 8X 8X 8X or 9X 9X 9X [2] Tracking Open [CD] or [SOURCE] Source On TRK MIN SEC [4] + [6] + Reset or [4] + [6] + BU + ACC Test Mode In [Key] Contents Display *1) TYP + 6 dB + 12 dB TRK MIN SEC TRK06MIN06SEC06 TRK12MIN12SEC12 *2) Focus Close S.Curve F EQ measurement setting TRK00MIN00SEC00 TRK01MIN01SEC01 TRK02MIN02SEC02 (TRK99MIN99SEC99) *3) F.Offset Display RF.offset T.Offset Display Switch to the order of the original display *4) 1TR/4TR/10TR/32TR/100TR *5) Single 4TR 10TR 32TR 100TR CRG Move 9x(8x) : 91(81) 92(82) 93(83) 94(84) 95(85) 96(86) *6) Only at the time of CRG move, 100TR jump *7) TRK/MIN/SEC F.AGC T.AGC Gain F Bias RF AGC *8) CRG motor voltage = 2 [V] *9) TYP (1X) 2X 1X TRK MIN SEC TRK22MIN22SEC22 TRK11MIN11SEC11 • As for the double speed (2x), audio output cannot be supported • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete. • When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens sticks to Wall, causing the actuator to be damaged). • In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released. • When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. • Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows) *10) OFF(TYP) FORCUS TRACKING TRK MIN SEC TRK70MIN70SEC70 TRK71MIN71SEC71 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 27 5 6 7 8 5 6 7 8 C D F A B E 7. DISASSEMBLY 2 3 Fig.1 Fig.2 Fig.3 1 - Removing the Panel Assy (Fig.1) Remove the two hooks and then remove the Panel Assy. Remove the two hooks. 1 2 Remove the two screws. Remove the screw. Lift off the Tuner Amp Assy from the Heat sink side. 4 - Removing the CD Mechanism Module (Fig.2, 3, 4) The CD Mechanism Module side is made a bottom. Fig.4 5 6 Push the area and remove the two hooks. Slide the Tuner Amp Assy in the direction of the arrow and then remove the hooks of upper and lower. The Tuner Amp Unit is fixed into the ditch. Disconnect the FFC and then remove the CD Mechanism Module. Panel Assy 2 2 CD Mechanism Module While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same. 3 3 1 Heat sink side CD Mechanism Module Tuner Amp Assy 5 5 6 1 2 2 1 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 28 1 2 3 4 1 2 3 4 C D F A B E 3 Fig.5 1 - Removing the Tuner Amp Unit (Fig.5) Straighten the tabs at two locations indicated and then remove the Tuner Amp Unit. 2 Remove the two screws. Remove the two screws. - Attention of removing (Fig.6) Fig.6 Don't remove this screws excluding the dismantlement of the CD Mechanism Module. Tuner Amp Unit 1 1 2 2 3 3 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 29 5 6 7 8 5 6 7 8 C D F A B E Fig.7 Fig.8 Fig.9 Fig.10 - Disassembling the Panel Part (Fig.7, 8) 2. Press the upside hook and the bottom side hook of the button at the same time, and pull out the button. 1. Remove the arm while bending the rib of the panel upward. - Assembling the Panel Part (Fig.9, 10, 11) 1. Attach the button from the front side of the panel. 2. Attach the spring to the arm as shown in the figure. Hitch the spring to the groove. The bended tip of the spring is set to this side. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 30 1 2 3 4 1 2 3 4 C D F A B E Fig.11 3. Fit the spring in the groove at the position shown in the figure. 4. Fit the boss on the lower side of the arm in the lower hole of the panel, and then warp the rib on the panel in the direction shown in the figure and fit the boss of the arm in the panel. Solder temp. : 360 ± 20 C Note: Soldering of the part shown in the figure must be done after fixing the Tuner Amp Unit to the bottom chassis. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 31 5 6 7 8 5 6 7 8 C D F A B E Correct way of holding the unit Incorrect way of holding the unit How to carry the mecha unit 1. Hold the designated points (shown with dashed lines) of the upper chassis and the front/rear bracket. 2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion. 3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx. 8N or less) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 32 1 2 3 4 1 2 3 4 C D F A B E Slide toward inner circumference Normal built-in state The spring is below a resin flange and is built inside the sheet metal bending. [Incorrect built-in state] The chassis is not nipped between the PU case and the PU rack. Outer holder Rear end of feeding screw Fig 1 Fig 3 Fig 4 Fig 2a Fully-hooked state B Tentatively-hooked state Fig 2b A How to remove the PU unit 1. Create an empty-clamp state according to “How to create empty clamp state (motor drive)”. 2. Hook the feeding screw biasing spring to a tentative hooking portion (Fig 2b). Be careful not to get injured by the spring edge. 3. Hold the PU at the position A as shown in Fig 1. Slide the PU as far as possible toward the holder in the feeding screw so that a joint on the outer end of the feeding screw is loosened. 4. As shown in Fig 3, move the rear end of the feeding screw laterally and then upward, to remove it from the outer holder. 5. Lift the PU unit to disengage it from Part B of the chassis (Fig 4), and remove the PU unit. (Cautions) When re-installing the PU, be sure to first nip the chassis and the PU unit (Fig 4) at the position B. Also, make sure to fully hook the feeding screw biasing spring (Fig 2a). Please follow the service manual for adjustment of the PU unit after the re-installation. How to move the PU to the outer circumference 1. Create an empty clamp state according to “How to create empty clamp state of mecha module”. 2. Apply 1.5 V to the CRG motor and move the PU to the outer circumference. (Caution) After moving the PU to the outer circumference and performing necessary treatment, make sure to solder the lead wires. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 33 5 6 7 8 5 6 7 8 C D F A B E www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 34 1 2 3 4 1 2 3 4 C D F A B E 8. EACH SETTING AND ADJUSTMENT 8.1 CD ADJUSTMENT 1) Cautions on adjustments In this product the single voltage (3.3 V) is used for the regulator. The reference voltage is the REFO1 (1.65 V) instead of the GND. If you should mistakenly short the REFO1 with the GND during adjustment, accurate voltage will not be obtained, and the servo’s misoperation will apply excessive shock to the pickup. To avoid such problems: a. Do not mix up the REFO1 with the GND when connecting the (-) probe of measuring instruments. Especially on an oscilloscope, avoid connecting the (-) probe for CH1 to the GND. b. In many cases, measuring instruments have the same potential as that for the (-) probe. Be sure to set the measuring instruments to the floating state. c. If you have mistakenly connected the REFO1 to the GND, turn off the regulator or the power immediately. Before mounting and removing filters or leads for adjustment, be sure to turn off the regulator. For stable circuit operation, keep the mechanism operating for about one minute or more after the regulator is turned on. In the test mode, any software protections will not work. Avoid applying any mechanical or electrical shock to the mechanism during adjustment. The RFAGC and RFO signals with a wide frequency range are easy to oscillate. When observing the signals, insert a resistor of 1k ohms in series. The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. 2) Test mode This mode is used to adjust the CD mechanism module. To enter the test mode. [4] + [6] -> Reset To exit from the test mode. Turn off the ACC and back up. Notes: a. During ejection, do not press any other keys than the EJECT key until the loaded disc is ejected. b. If you have pressed the (→) key or (←) key during focus search, turn off the power immediately to protect the actuator from damage caused by the lens stuck. c. For the TR jump modes except 100TR, the track jump operation will continue even if the key is released. d. For the CRG move and 100TR jump modes, the tracking loop will be closed at the same time when the key is released. e. When the power is turned off and on, the jump mode is reset to the single TR (91), the RF amp gain is set to 0 dB, and the auto-adjustment values are reset to the default settings. When a CD-DA (regular music CD) is played in the CD test mode, its sound quality will be temporarily deteriorated. The CD will then repeat normal, deteriorated, normal… playback. This is due to the difference in the playback modes between the normal operation mode and the CD test mode, and the interval of generating deteriorated mode and the time taken to return to the normal mode depend on the error of each clock. The time taken to turn to the deteriorated mode is at a minimum around 20 seconds while the time to return to the normal mode is maximum 40 seconds approximately. Make sure to check the sound quality in the normal operation mode. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 35 5 6 7 8 5 6 7 8 C D F A B E 8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT F E REFO2 CD CORE UNIT Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below. Purpose : To check that the grating is within an acceptable range when the PU unit is changed. Symptoms of Mal-adjustment : If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching. Method : Measuring Equipment Measuring Points Oscilloscope, Two L.P.F. E, F, REFO1 Disc TCD-782 Mode TEST MODE Checking Procedure 1. In test mode, load the disc and press BAND to switch the CD 3V regulator on. And then, check "00" indication. 2. Using the right and left buttons, move the PU unit to the innermost track. 3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the fourth press. 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75 . Refer to the photographs supplied to determine the phase angle. 5. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the mechanism should be judged to be at fault. Note Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble". 100 kohm 390 pF 100 kohm 390 pF E VREF F VREF Xch Ych L.P.F. L.P.F. Oscilloscope www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 36 1 2 3 4 1 2 3 4 C D F A B E Grating waveform 45 degrees 0 degrees 75 degrees 60 degrees 30 degrees 90 degrees Ech -> Xch 20 mV/div, AC Fch -> Ych 20 mV/div, AC www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 37 5 6 7 8 5 6 7 8 C D F A B E 8.3 PCL OUTPUT CONFIRMATION - PCL output Check that square wave of 1 Hz is output from BU_HSFLG (43 Pin) of IC601 by flipping TEST IN (112 Pin) of the same IC601 to ‘H’ while the product is operating normally (when stand-by state is released with ACC on). If clock signal is out of this range, this resonator (X601) must be changed for a new one. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 38 1 2 3 4 1 2 3 4 C D F A B E 9. EXPLODED VIEWS AND PARTS LIST 9.1 PACKING NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) " UC www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 39 5 6 7 8 5 6 7 8 C D F A B E (1) PACKING SECTION PARTS LIST (2) CONTRAST TABLE DEH-1300MP/XNUC, DEH-1350MP/XNES, DEH-1350MP/XNES1, DEH-1350MPG/XNES, DEH-1350MP/XNCN5 and DEH-1390MP/XNID are constructed the same except for the following: Owner's Manual,Installation Manual Mark No. Description Part No. 1 Polyethylene Bag See Contrast table (2) 2 Cord Assy QDP3013 * 3 Accessory Assy See Contrast table (2) 4 Screw See Contrast table (2) 5 Polyethylene Bag CEG1160 6 Handle QNC3021 7 Screw Assy See Contrast table (2) * 8 Polyethylene Bag CEG-127 9 Screw See Contrast table (2) 10 Screw TRZ50P080FTC 11 Unit Box See Contrast table (2) 12 Contain Box See Contrast table (2) 13 Protector QHP3016 14 Case Assy See Contrast table (2) 15 Remote Control Unit QXA3303 16-1 Owner's Manual See Contrast table (2) * 16-2 Warranty Card See Contrast table (2) * 16-3 Service Network See Contrast table (2) Mark No. Description Part No. Mark No. Description DEH-1300MP/XNUC DEH-1350MP/XNES DEH-1350MP/XNES1 1 Polyethylene Bag CEG1173 QEG3001 QEG3001 * 3 Accessory Assy QEA3008 QEA3009 QEA3009 4 Screw BPZ20P060FTC Not used Not used 7 Screw Assy YEA5072 YEA5082 YEA5082 9 Screw CRZ50P090FTC Not used Not used 11 Unit Box QHG3073 QHG3074 QHG3075 12 Contain Box QHL3073 QHL3074 QHL3075 14 Case Assy Not used QXA3129 QXA3129 16-1 Owner's Manual QRD3061 QRD3062 QRD3062 * 16-2 Warranty Card CRY1276 Not used CRY1250 * 16-3 Service Network Not used Not used CRY1251 Mark No. Description DEH-1350MPG/XNES DEH-1350MP/XNCN5 DEH-1390MP/XNID 1 Polyethylene Bag QEG3001 QEG3001 QEG3001 * 3 Accessory Assy QEA3009 QEA3009 QEA3009 4 Screw Not used Not used Not used 7 Screw Assy YEA5082 YEA5082 YEA5082 9 Screw Not used Not used Not used 11 Unit Box QHG3076 QHG3079 QHG3078 12 Contain Box QHL3076 QHL3079 QHL3078 14 Case Assy QXA3129 Not used QXA3129 16-1 Owner's Manual QRD3062 QRB3077 QRB3076 * 16-2 Warranty Card Not used YRY5002 CRY1304 * 16-3 Service Network Not used Not used CRY1305 Part No. Language QRD3061 English, French, Spanish(Espanol) QRD3062 English, Spanish(Espanol), Portuguese(B), Traditional Chinese, Arabic, Persian QRB3077 Simplified Chinese QRB3076 English www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 40 1 2 3 4 1 2 3 4 C D F A B E 9.2 EXTERIOR B A A A CN5 ID www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 41 5 6 7 8 5 6 7 8 C D F A B E (1) EXTERIOR SECTION PARTS LIST (2) CONTRAST TABLE DEH-1300MP/XNUC, DEH-1350MP/XNES, DEH-1350MP/XNES1, DEH-1350MPG/XNES, DEH-1350MP/XNCN5 and DEH-1390MP/XNID are constructed the same except for the following: Mark No. Description Part No. 1 Cord Assy QDP3013 2 Screw ASZ26P050FTC 3 Screw BSZ26P060FTC 4 Screw BSZ26P080FTC 5 Screw BSZ26P120FTC 6 CD Mechanism Module(S11.1) CXK5832 7 Cable QDE3011 8 Case QNB3001 9 Holder QNC3020 10 Panel QNS3127 11 Tuner Amp Unit See Contrast table (2) 12 Screw BPZ26P080FTC 13 Screw BSZ26P060FTC 14 Screw BSZ26P120FTC 15 FM/AM Tuner Unit(U401) CWE2256 16 Holder CND3466 17 Holder QNC3024 18 Heat Sink QNR3002 > 19 Fuse (10 A) YEK5001 20 Spring QBH3001 21 Cover QNM3029 22 Panel QNS3126 23 Arm QNV3025 24 Button QNV3026 25 Detachable Assy See Contrast table (2) 26 Screw BPZ20P100FTC 27 Spring CBH2210 28 Button(EJECT, E, B, D, LEFT) QAC3050 29 Button(AUDIO, FUNC, UP, DOWN) QAC3051 30 Button(RIGHT,- , 1-6) QAC3052 31 Button(DETACH) QAC3053 32 Cover QNS3125 33 LCD(V1801) CAW2008 34 Holder QNC3027 35 Lighting Conductor QNV3022 36 Rubber QNV3023 37 Connector YNV5192 38 Knob Unit QXA3153 39 Spring YBL5010 40 Grille Unit See Contrast table (2) 41 Remote Control Unit QXA3303 42 Cover CNS7068 43 Label See Contrast table (2) Mark No. Description Part No. Mark No. Description DEH-1300MP/XNUC DEH-1350MP/XNES DEH-1350MP/XNES1 11 Tuner Amp Unit QWM3162 QWM3163 QWM3163 25 Detachable Assy QXA3293 QXA3295 QXA3295 40 Grille Unit QXA3248 QXA3249 QXA3249 43 Label Not used Not used Not used Mark No. Description DEH-1350MPG/XNES DEH-1350MP/XNCN5 DEH-1390MP/XNID 11 Tuner Amp Unit QWM3163 QWM3164 QWM3163 25 Detachable Assy QXA3296 QXA3298 QXA3297 40 Grille Unit QXA3250 QXA3252 QXA3251 43 Label Not used CNN3533 CNN3533 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 42 1 2 3 4 1 2 3 4 C D F A B E 9.3 CD MECHANISM MODULE A C D C A B B C D (A) : GEM1045 (B) : GEM1038 (C) : GEM1024 (D) : GEM1043 (C) (C) (A) (A) (D) (D) (A) (A) (D) (A) (A) (A) (A) (A) (C) (C) (C) (C) (B) (C) (C) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 43 5 6 7 8 5 6 7 8 C D F A B E CD MECHANISM MODULE SECTION PARTS LIST Mark No. Description Part No. 1 ..... 2 Screw BSZ20P040FTC 3 Screw(M2 x 4) CBA1835 4 Washer CBF1038 5 Spring CBH3010 6 Spring CBH2855 7 Spring CBH2856 8 Spring CBH2860 9 Screw BSZ26P060FTC 10 Spring CBH3011 11 Spring CBH3012 12 Spring CBH3014 13 Spring CBH3015 14 Spring CBH3016 15 Spring CBH3017 16 Spring CBH3086 17 Spring CBH3019 18 ..... 19 Spring CBL1822 20 Pickup Unit(P10.5)(Service) CXX1942 21 Bracket CND4553 22 Arm CND4555 23 Bracket CND5709 24 Bracket CND5710 25 Lever CND5398 26 Sheet CNN2280 27 Rack CNV8342 28 Guide CNW1171 29 Roller CNW1172 30 Arm CNW2157 31 Arm CNW1174 32 Roller CNW1175 33 Lever CNW1176 34 Arm CNW1177 35 Arm CNW1178 36 Gear CNW1180 37 Gear CNW1181 38 ..... 39 Gear CNW1183 40 Rack CNW1184 41 Gear CNW1185 42 Gear CNW1186 43 Gear CNW1187 44 Gear CNW1188 45 Clamper CNW1190 46 Arm CNW1192 47 Holder CNW1193 48 Holder CNW1194 49 Damper CNW1197 50 Damper CNW1198 51 Arm CNW1726 52 Motor Unit(LOAD/CRG)(M2) CXC4026 53 Screw Unit CXC8894 54 Arm Assy CXE3849 55 Washer CBF1037 56 Washer CBF1038 57 Arm CND5886 58 Collar CNV6906 59 Roller CNW1196 60 Gear Unit CXC8893 61 Washer YE15FTC 62 Chassis Unit CXE3818 63 Motor Unit(SPDL)(M1) CXE2273 64 Screw JFZ20P025FTC 65 Screw JGZ17P022FTC 66 Screw EBA1028 67 CD Core Unit (S11.1COMP) CWX3957 68 Chassis CNA3181 Mark No. Description Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 44 1 2 3 4 1 2 3 4 C D F A B E 10. SCHEMATIC DIAGRAM 10.1 TUNER AMP UNIT(GUIDE PAGE) A A-a A-a A-b A-a A-b A-b A-a Large size SCH diagram Guide page Detailed page Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". FM/AM TUNER UNIT VOLTAGE(V) DESTINATION R680 R681 OPEN (P. Down) 0.00 (0.00 - 0.41) 0.88 (0.42 - 1.23) 3.08 (2.89 - 3.30) B,C,D,F E A NM 47k 12k 33k 3.3k 47k * * A B C D E F DEH-1300MP/XNUC DEH-1350MP/XNES DEH-1350MP/XNES1 DEH-1350MPG/XNES DEH-1350MP/XNCN5 DEH-1390MP/XNID The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. NOTE : Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. NM : No Mount PN5043A C CN701 B CN1801 ANTENNA NM FM(30%): -24 dBs AM(30%): -24 dBs CD:+0.6 dBs AUX:+2.2 dBs FM(3 AM( www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 45 5 6 7 8 5 6 7 8 C D F A B E A A-b 1SR154-400 1SR154-400 NM > A TUNER AMP UNIT REAR OUTPUT NM NM NM 3A NM 600 uH YEK5001 (10A) > Fuse CD:+0.6 dBs FM(30%): -5.9 dBs AM(30%): -4.9 dBs CD:+10.7 dBs AUX:+10.3 dBs FM(30%):+20.1 dBs ±2 dBs AM(30%):+21.1 dBs ±2 dBs CD:+36.7 dBs ±2 dBs AUX:+36.3 dBs ±2 dBs FM(30%): -10.9 dBs AM(30%): -9.9 dBs CD:+5.7 dBs AUX:+5.3 dBs www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 46 1 2 3 4 1 2 3 4 C D F A B E A-a A-b A-b > A TUNER AMP UNIT REAR OUTPUT 3A NM s FM(30%): -5.9 dBs AM(30%): -4.9 dBs CD:+10.7 dBs AUX:+10.3 dBs FM(30%): -10.9 dBs AM(30%): -9.9 dBs CD:+5.7 dBs AUX:+5.3 dBs www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 47 5 6 7 8 5 6 7 8 C D F A B E A-a A-b A-b 1SR154-400 1SR154-400 NM NM NM NM 600 uH YEK5001 (10A) > Fuse FM(30%):+20.1 dBs ±2 dBs AM(30%):+21.1 dBs ±2 dBs CD:+36.7 dBs ±2 dBs AUX:+36.3 dBs ±2 dBs www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 48 1 2 3 4 1 2 3 4 C D F A B E A-b A-a A-a A-b FM/AM TUNER UNIT PN5043A C CN701 ANTENNA NM FM(30%): -24 dBs AM(30%): -24 dBs CD:+0.6 dBs FM(30%): -1 AM(30%): - CD:+ AUX:+ www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 49 5 6 7 8 5 6 7 8 C D F A B E A-a A-b A-b A-a VOLTAGE(V) DESTINATION R680 R681 OPEN (P. Down) 0.00 (0.00 - 0.41) 0.88 (0.42 - 1.23) 3.08 (2.89 - 3.30) B,C,D,F E A NM 47k 12k 33k 3.3k 47k * * A B C D E F DEH-1300MP/XNUC DEH-1350MP/XNES DEH-1350MP/XNES1 DEH-1350MPG/XNES DEH-1350MP/XNCN5 DEH-1390MP/XNID The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. NOTE : Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. NM : No Mount PN5043A B CN1801 ANTENNA AUX:+2.2 dBs www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 50 1 2 3 4 1 2 3 4 C D F A B E 10.2 KEYBOARD UNIT B SEG18 SEG30 SEG32 SEG19 COM0 SEG11 SEG25 SEG12 KST0 KST1 SEG15 KST3 COM3 COM2 COM2 SEG1 SEG35 COM1 COM1 SEG34 COM0 KDT2 SEG38 KDT3 KST4 SEG2 SEG24 SEG3 SEG23 SEG4 SEG22 SEG17 SEG16 SEG37 SEG27 KST2 SEG26 SEG36 SEG13 SEG8 SEG21 KST4 SEG9 SEG20 SEG14 KST0 SEG10 SEG29 KDT0 KST2 SEG7 SEG28 COM3 SEG6 KDT1 SEG31 SEG33 SEG5 SEG12 SEG16 SEG34 SEG15 SEG10 SEG29 SEG6 SEG36 SEG35 SEG8 SEG13 SEG2 SEG32 SEG37 SEG1 SEG20 SEG28 SEG38 SEG19 SEG17 SEG31 SEG22 SEG11 SEG4 SEG9 SEG21 SEG30 SEG7 SEG25 SEG27 SEG23 SEG26 SEG33 SEG5 SEG18 SEG3 SEG14 SEG24 KST3 KDT3 KDT1 KST1 KDT2 C1801 1u/10 C1802 DGND DGND IC1801 PD6340A SEG4 1 SEG3 2 SEG2 3 SEG1 4 SEG0 5 COM3 6 COM2 7 COM1 8 COM0 9 VLCD 10 KST3 11 KST2 12 KST1 13 KST0 14 KDT0 15 KDT1 16 MODA 21 X0 22 X1 23 VSS 24 KDT2 25 KDT3 26 NC2 27 KST4 28 SEG39 29 SEG38 30 SEG37 31 SEG36 32 SEG35 33 SEG34 34 SEG33 35 SEG32 36 SEG31 37 SEG30 38 SEG29 39 SEG28 40 SEG27 41 SEG26 42 SEG25 43 SEG24 44 SEG23 45 SEG22 46 SEG21 47 SEG20 48 SEG16 52 SEG15 53 SEG14 54 SEG13 55 VDD 56 SEG12 57 SEG11 58 SEG10 59 SEG9 60 SEG8 61 SEG7 62 SEG6 63 SEG5 64 KYDT 20 NC1 19 DPDT 18 REM 17 SEG17 51 SEG18 50 SEG19 49 GP1UXC14RK IC1802 1 REM 2 GND 3 VCC R1804 R1802 2.2k R1806 R1801 R1803 2.2k R1805 NM S1817 1 2 S1803 1 2 S1812 1 2 S1804 1 2 S1816 1 2 S1814 1 2 S1810 1 2 S1811 1 2 S1801 1 2 S1807 1 2 S1806 1 2 S1815 1 2 S1809 1 2 S1808 1 2 S1802 1 2 S1805 1 2 S1813 1 2 V1801 1 NC1 2 NC2 3 SEG1 4 SEG2 5 SEG3 6 SEG4 7 SEG5 8 SEG6 9 SEG7 10 SEG8 11 SEG9 12 SEG10 13 SEG11 14 SEG12 15 SEG13 16 SEG14 17 SEG15 18 SEG16 19 SEG17 20 SEG18 21 SEG19 22 SEG20 23 SEG21 24 SEG22 25 SEG23 26 SEG24 27 SEG25 28 SEG26 29 SEG27 30 SEG28 31 SEG29 32 SEG30 33 SEG31 34 SEG32 35 SEG33 36 SEG34 37 SEG35 38 SEG36 39 SEG37 40 SEG38 41 COM0 42 COM1 43 COM2 44 COM3 X1801 10 uF 2.2 NM 100 REMOTE DPDT KYDT A,B,C D,E,F DISP CD EJE 3 2 4 6 BAND EQ DOWN RIGHT UP AUDIO CAW2008 CSS1547 5MHz CLK LED COLOR 2.7K(1/4W) 1.8K(1/4W) 560(1/4W) GREEN R1808 RED 390(1/4W) R1810,R1811,R18 R1809 1K(1/4W) 390(1/4W) A B C D E F DEH-1300MP/XNUC DEH-1350MP/XNES DEH-1350MP/XNES1 DEH-1350MPG/XNES DEH-1350MP/XNCN5 DEH-1390MP/XNID *1 LCD www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 51 5 6 7 8 5 6 7 8 C D F A B E B KDT1 KDT2 KDT0 CN1801 ILMGND 1 DGND 2 ROT1 3 KYDT 4 ROT0 5 DPDT 6 ILM+B 7 ILMCLR 8 AUXR 9 SOURCE 10 AUXG 11 SW5V 12 AUXL 13 DSEN 14 C1803 0.1u/16 C1804 4700p/50 C1805 4700p/50 D1803 D1817 SMLXA4WBETW1(Z1) D1801 D1806 D1804 D1811 D1816 D1813 D1802 D1808 D1812 D1815 D1807 D1809 D1814 D1826 D1822 D1821 D1825 D1832 D1823 D1827 D1831 D1824 D1818 D1834 D1837 D1829 D1835 D1836 D1805 D1830 D1810 D1828 D1833 D1839 NM D1838 NM DGND DGND DGND DGND ILMGND ILMGND JA1801 2 1 3 LTC114EUB Q1802 R1818 R1811 R1807 270 1/4W R1817 NM R1823 47k R1821 R1812 R1809 R1824 R1819 NM R1820 10k R1815 270 R1814 10k R1822 1.2k R1816 NM R1813 R1826 2.7k R1810 R1827 R1825 R1808 S1817 1 2 S1820 1 2 S1812 1 2 S1816 1 2 S1814 1 2 1 1 2 S1818 1 2 S1815 1 2 S1821 1 2 S1819 1 2 2 S1822 1 2 2 S1823 1 2 S1813 1 2 S1824 1 1 2 2 3 3 4 4 5 5 TP1801 TP1802 ILM+B ILMCLR SW5V TP1803 UMX1N Q1801 E1 1 B1 2 C2 3 E2 4 5 B2 6 C1 VA1819 EZJZ1V270RM VA1820 EZJZ1V270RM R1828 270 1/4W ILM+B 13.9V SWVDD AUX EJECT DISP CLK(TA) 1 2 3 4 5 6 UP DOWN LEFT RIGHT AUDIO BAND EQ 5.1V CD EJECT 2 1 6 5 EQ FUNC HT UP LEFT SRC O FUNC CKN1082 CKS6230 SWVDD 5.1V K SML-D12V8W(PQ) 2.7K(1/4W) 0 4W) 560(1/4W) SML-D12P8W(KL) R1810,R1811,R1812 D1802-D1818 SW DEFAULT AMBER RED/GREEN AMBER BAND DOWN EJECT 6 UP FUNC EQ LEFT 4 5 2 3 DISP CLK(TA) 1 AUDIO RIGHT CSD1168 9 W) NM *1 AUX A CN801 B KEYBOARD UNIT www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 52 1 2 3 4 1 2 3 4 C D F A B E 10.3 CD MECHANISM MODULE(GUIDE PAGE) C C-a 1 TOP 2 FOP 3 FOM 4 TOM 5 MD 6 A+C 7 VR 8 VREF 9 P1+P6 10 GND 11 P5+P10 12 VCC 13 B+D 14 LD+ 15 LD- FOCUS ACT TRK ACT P4 LD VCC P8 P2 P1 P6 P5 P10 P3 P9 P7 MD HOLOGRAM UNIT E:P5+P10 F:P1+P6 M2 LOADING/CARRIAGE MOTOR M1 SPINDLE MOTOR VDSENS HOME PD E F BD AC MD SD FD TD BD E F AC TOM FOM FOP TOP PD TD FD CONT FOP FOM TOM TOP SOM SOP LCOM LCOP LOEJ CLCONT SD DSCSNS 8EJ SOM SOP LCOM LCOP MD 8EJ HOME FLMD0 VDSENS REFOUT REFOUT REFOUT VD VD VD VD PGND PGND PGND DSCSNS GND GND GND GND SWVDD VDD VDD IC301 BA5839FP VR 1 OPIN2+ 2 OPIN2- 3 OPOUT2 4 5 OPIN1+ 6 OPIN1- 7 OPOUT1 29 FIN1 9 MUTE 10 PowVcc1 11 VO1- 12 VO1+ 13 VO2- 14 VO2+ 8 GND1 15 VO3+ 17 VO4+ 18 VO4- 19 PowVcc2 20 GND2 21 CNT 22 LDIN 23 OPOUTSL 24 OPINSL 25 OPOUT3 26 OPIN3- 27 OPIN3+ 28 PreVcc 16 VO3- 30 FIN2 NM TH201 2SA1577(QR) Q101 C102 NM C203 NM C708 NM C202 0.1u/10 C204 0.01u/16 C213 0.1u/10 C216 3300p/50 C217 0.1u/10 C218 0.047u/16 C219 0.1u/10 C220 1800p/50 C221 0.1u/10 C224 0.1u/10 C226 68p/50 C227 47p/50 C236 0.1u/10 C240 0.1u/10 C250 1000p/50 C251 1000p/50 C303 4700p/25 C304 0.022u/16 C711 NM R203 NM (1608) R221 10k R22210k R225 10k R226 39k R254 100k R256 100k R261 NM R307 18k R308 18k R310 18k R309 18k C105 NM C110 NM C111 NM NM C305 C709 NM C710 NM R106 NM R108 NM R236 NM C106 4.7u/6.3 (2125) C222 56p/50 C223 4p/50 C228 0.01u/16 C229 0.1u/10 C239 22p/50 C307 1u/10 (1608) R101 2.4 R102 2.4 R103 2.7 R104 2.2k R107 1M R214 4.7k R216 4.7k R227 5.6k R228 1.2k R229 4.7k R232 1.2k R240 47k (1608) R241 10k FULL EMPTY ADIN FLMD0 TE TEC TEMP CLCONT VDSENS FE MDX LOEJ RFO ATEST LD F B+D PD E A+C TIN CONT HOME 8SNS TOM DSCSNS FOM FOP SIN TOP FIN CIN RFAGC D101 NM MDY RED GN WH BLK REFO1 PU+3V LD1 V3R3 REFO2 NM S905 8EJ 1 NC 2 3 4 NC CSN1081-A S903 DSCSNS 1 NC 2 3 4 NC CSN1080-A S901 HOME 1 NC 2 3 4 NC 1 (EMPTY) 2 (FULL) 3 (RAM0) 4 (RAM1) 5 (RAM2) NC6 6 /8SNS 7 NC7 8 /HOME 9 /DSCSNS 10 VDSENS 11 TEMP 12 ADC.VDD 13 ADC.GND 14 FLMD0 15 RDB15 94 IO.GND 95 IO.VDD 96 RA0 97 RA1 98 RA2 99 RA3 100 RA4 101 RA5 102 RA6 103 RA7 104 RA8 105 RA9 106 RA10 107 RA11 108 FD 109 TD 110 SD 111 MD 112 EFM 113 ASY 114 ATEST 115 A.VDD1 116 A.GND1 117 RFI 118 AGCO 119 C3T 120 AGCI 121 RFO 122 EQ2 123 EQ1 124 RF2- 125 RF- 126 A.GND2 127 A.VDD2 128 A 129 B 130 F 131 E 132 REFOUT 133 FE- 134 FEO 135 ADCIN 136 TE- 137 TEO 138 TE2 139 TEC 140 LD 141 PD 142 AD.VDD 143 AD.GND 144 CKS4808-A CN101 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RAM0 RAM1 RAM2 R291 2.7k C293 1000p/50 R258 NM R259 0 NM C306 LTA123JUB Q102 SWVDD C308 NM (1608) (1608) (1/10W) MOTOR DRIVER LOGIC TABLE LOAD EJ PLAY OFF CLCONT H H L L LOEJ L H - - CONT L L H L F.ACT:Applying positive voltage to FOP. the lens moves DISC side. T.ACT:Applying positive voltage to TOP. the lens moves outer circumference. NOTE1) GND CD LSI , RFAMP , CPU PGND Actuator , Motor Driver AGND Audio These GND's are not connected to each other on PCB. PGND is connected to a floating mechanism part by a screw. 1 2 Land for manual soldering PICKUP UNIT(P10.5) (SERVICE) SWITCHES: CD CORE UNIT S901:HOME SWITCH.........ON-OFF S903:DSCSNS SWITCH.....ON-OFF The underlined indicates the switch position. CXX1942 CXE2273 CXC4026 T T F F F C S T T F F T S S C C F T S C F T F T T F F T S S C C 1 2 3 4 6 7 8 9 b c d e www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 53 5 6 7 8 5 6 7 8 C D F A B E C C-b BSCK BRST LOUT ROUT ROUT LOUT CONT BSRQ BDATA BSCK RESET VDSENS HOME LOEJ 8EJ FLMD0 BRST RX RESET FLMD0 TX BRXEN TX RX VD VD AGND AGND PGND PGND DSCSNS CLCONT RESET GND GND GND GND GND SWVDD BSRQ BRXEN BDATA VDD X201 CSS1603-A 16.93MHz 1 2 3 NM TH201 C203 NM C208 NM C202 0.1u/10 C204 0.01u/16 C206 0.1u/10 C207 0.1u/16 (1608) C211 0.1u/10 C212 NM (1608) C213 0.1u/10 C214 0.1u/10 R203 NM (1608) R204 220 R254 100k R256 100k R261 NM R702 220 C230 NM (1608) C601 NM C602 NM C701 NM C702 NM C705 NM C706 NM (1608) C707 NM C205 4.7u/6.3(2125) 22u/6.3 C209 C210 0.1u/10 C704 1000p/50 R206 100k R210 1k R233 10k R244 47k R701 220 AGND1 BSCK BDATA BRXEN BSRQ ROUT RESET BRST CD3VON RX LRCK LRCKOK TX DOUT PUEN MCKRQ LOUT BSCK2 FLMD0 TESTIN TEMP ROM CN704 NM 1 VDD 2 FLMD0 3 4 RESET 5 6 TX 7 8 RX 9 10 GND RFOK MIRR LOCK HOLD GND4 GND1 GND3 VDD VD_1 VD_2 PGND1 PGND2 VDD_2 NM IC202 CS 1 SK 2 DI 3 DO 4 5 GND 6 TEST 7 NC 8 VCC R234 47k R202 47k R235 47k CPRST R201 NM (1608) R243 NM (1608) C201 NM (1608) R245 NM CKS4808-A CN701 1 VD 7.5V 2 VD 7.5V 3 /BSRQ 4 /BRST 5 /BSCK 6 BRXEN 7 BDATA 8 /RESET 9 VDD 3.3V 10 GND GND 11 ROUT 12 AGND GND 13 LOUT 14 GND GND 15 PGND GND C703 100p/50 R237 470 PE5746A IC201 (RAM2) NC6 6 /8SNS 7 NC7 8 /HOME 9 /DSCSNS 10 VDSENS 11 TEMP 12 ADC.VDD 13 ADC.GND 14 FLMD0 15 /RESET 16 /ADENA 17 18 (/EJSW) /TESTIN 19 CLCONT 20 BSI 21 BSO 22 /BSCK 23 FTxD 24 FRxD 25 BRXEN 26 /BSRQ 27 LOEJ 28 ROM 29 NC9 30 31 NC10 32 VDCONT 33 CDMUTE 34 ROMDATA 35 ROMCK 36 ROMCS MCKRQ 37 LRCKOK 38 /PUEN 39 CD3VON 40 CONT 41 NC11 42 NC12 43 NC13 44 TEST 45 /BRST 46 REGS 47 C.VDD 48 C.GND 49 XTAL 50 X.GND 51 /XTAL 52 X.VDD 53 DA.VDD1 54 LOUT 55 DA.GND1 56 REGC 57 DA.GND2 58 ROUT 59 DA.VDD2 60 D.GND 61 D.VDD 62 REG16 63 LRCK 64 SCKO 65 DOUT 66 SVMON0 67 SVMON1 68 SVMON2 69 SVMON3 70 C33M 71 (/RCS) 72 (CKE) 73 /RAS 74 /CAS0(LDQM) 75 /CAS1(UDQM) 76 /WE 77 /OE(/CAS) 78 RDB0 79 RDB1 80 RDB2 81 RDB3 82 RDB4 83 RDB5 84 RDB6 85 RDB7 86 RDB8 87 RDB9 88 RDB10 89 RDB11 90 RDB12 91 RDB13 92 RDB14 93 RDB15 94 IO.GND 95 IO.VDD 96 RA0 97 RA1 98 RA2 99 RA3 100 RA4 101 RA5 102 RA6 103 RA7 RAM2 SCKO R258 NM C215 0.1u/10 AGND2 SWVDD DM DM2 DP DP2 OCI VDCONT CDMUTE C730 NM (1608) USBGND CPRDY NM Q201 I/O C201 C207 C212 C230 C307 C308 C706 C730 R101 R102 R103 R201 R203 R240 R243 C106 C205 34 35 36 72 71 IC201 IC202 IC301 D101 Q101 Q102 Q201 C209 C305 C306 1608:PARTS 2125:PARTS Parts with Polarity A CN701 C CD CORE UNIT(S11.1Comp) F SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE T C S 5 a f g www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 54 1 2 3 4 1 2 3 4 C D F A B E C-a C-b C-b ROUT LOUT CONT BRST AGND GND VDD X201 CSS1603-A 16.93MHz 1 2 3 C208 NM C202 0.1u/10 C206 0.1u/10 C207 0.1u/16 (1608) C211 0.1u/10 C212 NM (1608) C213 0.1u/10 C214 0.1u/10 C230 NM (1608) C601 NM C602 NM C205 4.7u/6.3(2125) 22u/6.3 C209 C210 0.1u/10 R210 1k 33 k CD3VON RX LRCK LRCKOK TX DOUT PUEN MCKRQ BSCK2 FLMD0 TESTIN TEMP RFOK MIRR LOCK HOLD NM IC202 CS 1 SK 2 DI 3 6 TEST 7 NC 8 VCC 35 47k R201 R243 NM C201 NM (1608) R237 470 PE5746A IC201 NC6 /8SNS 7 NC7 8 /HOME 9 /DSCSNS 10 VDSENS 11 TEMP 12 ADC.VDD 13 ADC.GND 14 FLMD0 15 /RESET 16 /ADENA 17 18 (/EJSW) /TESTIN 19 CLCONT 20 BSI 21 BSO 22 /BSCK 23 FTxD 24 FRxD 25 BRXEN 26 /BSRQ 27 LOEJ 28 ROM 29 NC9 30 31 NC10 32 VDCONT 33 CDMUTE 34 ROMDATA 35 ROMCK 36 ROMCS MCKRQ 37 LRCKOK 38 /PUEN 39 CD3VON 40 CONT 41 NC11 42 NC12 43 NC13 44 TEST 45 /BRST 46 REGS 47 C.VDD 48 C.GND 49 XTAL 50 X.GND 51 /XTAL 52 X.VDD 53 DA.VDD1 54 LOUT 55 DA.GND1 56 REGC 57 DA.GND2 58 ROUT 59 DA.VDD2 60 D.GND 61 D.VDD 62 REG16 63 LRCK 64 SCKO 65 DOUT 66 SVMON0 67 SVMON1 68 SVMON2 69 SVMON3 70 C33M 71 (/RCS) 72 (CKE) 73 /RAS 74 /CAS0(LDQM) 75 /CAS1(UDQM) 76 /WE 77 /OE(/CAS) 78 RDB0 79 RDB1 80 RDB2 81 RDB3 82 RDB4 83 RDB5 84 RDB6 85 RDB7 86 RDB8 87 RDB9 88 RDB10 89 RDB11 90 RDB12 91 RDB13 92 RDB14 93 RDB15 94 IO.GND 95 IO.VDD 96 RA0 97 RA1 98 RA2 99 RA3 100 RA4 101 RA5 102 RA6 SCKO C215 0.1u/10 VDCONT CDMUTE C201 C207 C212 C230 C307 C308 C706 C730 R101 R102 R103 R201 R203 R240 R243 C106 C205 34 35 36 72 71 IC201 IC202 IC301 D101 Q101 Q102 Q201 C209 C305 C306 1608:PARTS 2125:PARTS Parts with Polarity C CD CORE UNIT(S11.1Comp) F SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE T C S a www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 55 5 6 7 8 5 6 7 8 C D F A B E C-a C-b C-b BSCK BRST LOUT ROUT BSRQ BDATA BSCK RESET VDSENS HOME LOEJ 8EJ FLMD0 RX RESET FLMD0 TX BRXEN TX RX VD AGND D PGND DSCSNS CLCONT RESET GND GND GND SWVDD BSRQ BRXEN BDATA NM TH201 C203 NM C202 0.1u/10 C204 0.01u/16 R203 NM (1608) R204 220 R254 100k R256 100k R261 NM R702 220 C701 NM C702 NM C705 NM C706 NM (1608) C707 NM C704 1000p/50 R206 100k R233 10k R244 47k R701 220 AGND1 BSCK BDATA BRXEN BSRQ ROUT RESET BRST RX LRCKOK TX MCKRQ LOUT BSCK2 FLMD0 TESTIN TEMP ROM CN704 NM 1 VDD 2 FLMD0 3 4 RESET 5 6 TX 7 8 RX 9 10 GND GND4 GND1 GND3 VDD VD_1 VD_2 PGND1 PGND2 VDD_2 NM IC202 CS 1 SK 2 DI 3 DO 4 5 GND 6 TEST 7 NC 8 VCC R234 47k R202 47k R235 47k CPRST R201 NM (1608) R243 NM (1608) C201 NM (1608) R245 NM CKS4808-A CN701 1 VD 7.5V 2 VD 7.5V 3 /BSRQ 4 /BRST 5 /BSCK 6 BRXEN 7 BDATA 8 /RESET 9 VDD 3.3V 10 GND GND 11 ROUT 12 AGND GND 13 LOUT 14 GND GND 15 PGND GND C703 100p/50 NC6 /8SNS 7 NC7 8 /HOME 9 /DSCSNS 10 VDSENS 11 TEMP 12 ADC.VDD 13 ADC.GND 14 FLMD0 15 /RESET 16 /ADENA 17 18 (/EJSW) /TESTIN 19 CLCONT 20 BSI 21 BSO 22 /BSCK 23 FTxD 24 FRxD 25 BRXEN 26 /BSRQ 27 LOEJ 28 ROM 29 NC9 30 31 NC10 32 VDCONT 33 CDMUTE 34 35 36 MCKRQ 37 LRCKOK 38 39 NM AGND2 DM DM2 DP DP2 OCI VDCONT CDMUTE C730 NM (1608) USBGND CPRDY NM Q201 I/O A CN701 5 f g www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 56 1 2 3 4 1 2 3 4 C D F A B E C-b C-a C-a C-b 1 TOP 2 FOP 3 FOM 4 TOM 5 MD 6 A+C 7 VR 8 VREF 9 P1+P6 10 GND 11 P5+P10 12 VCC 13 B+D 14 LD+ 15 LD- FOCUS ACT TRK ACT P4 LD VCC P8 P2 P1 P6 P5 P10 P3 P9 P7 MD HOLOGRAM UNIT E:P5+P10 F:P1+P6 M2 LOADING/CARRIAGE MOTOR M1 SPINDLE MOTOR PD E F BD AC MD SD FD TD BD E F AC TOM FOM FOP TOP PD SOM SOP REFOUT REFOUT GND GND VDD VDD 2SA1577(QR) Q101 C102 NM C202 0.1u/10 C213 0.1u/10 C216 3300p/50 C217 0.1u/10 C218 0.047u/16 C219 0.1u/10 C220 1800p/50 C221 0.1u/10 C224 0.1u/10 C226 68p/50 C227 47p/50 C236 0.1u/10 C240 0.1u/10 C250 1000p/50 C251 1000p/50 R221 10k R22210k R225 10k R226 39k C105 NM C110 NM C111 NM R106 NM R108 NM R236 NM C106 4.7u/6.3 (2125) C222 56p/50 C223 4p/50 C228 0.01u/16 C229 0.1u/10 C239 22p/50 R101 2.4 R102 2.4 R103 2.7 R104 2.2k R107 1M R214 4.7k R216 4.7k R227 5.6k R228 1.2k R229 4.7k R232 1.2k FULL EMPTY ADIN TE TEC TEMP FE RFO ATEST LD F B+D PD E A+C RFAGC D101 NM RED BLK REFO1 PU+3V LD1 V3R3 1 (EMPTY) 2 (FULL) 3 (RAM0) 4 (RAM1) 5 (RAM2) NC6 6 /8SNS 7 NC7 8 /HOME 9 /DSCSNS 10 VDSENS 11 TEMP 12 ADC.VDD 13 14 95 IO.VDD 96 RA0 97 RA1 98 RA2 99 RA3 100 RA4 101 RA5 102 RA6 103 RA7 104 RA8 105 RA9 106 RA10 107 RA11 108 FD 109 TD 110 SD 111 MD 112 EFM 113 ASY 114 ATEST 115 A.VDD1 116 A.GND1 117 RFI 118 AGCO 119 C3T 120 AGCI 121 RFO 122 EQ2 123 EQ1 124 RF2- 125 RF- 126 A.GND2 127 A.VDD2 128 A 129 B 130 F 131 E 132 REFOUT 133 FE- 134 FEO 135 ADCIN 136 TE- 137 TEO 138 TE2 139 TEC 140 LD 141 PD 142 AD.VDD 143 AD.GND 144 CKS4808-A CN101 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RAM0 RAM1 RAM2 R291 2.7k C293 1000p/50 LTA123JUB Q102 (1608) (1/10W) F.ACT:Applying positive voltage to FOP. the lens moves DISC side. T.ACT:Applying positive voltage to TOP. the lens moves outer circumference. 1 2 PICKUP UNIT(P10.5) (SERVICE) CXX1942 CXE2273 T T F F F C S T F T F T T F F T S S b c e www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 57 5 6 7 8 5 6 7 8 C D F A B E C-a C-b C-b C-a M2 LOADING/CARRIAGE MOTOR SPINDLE MOTOR VDSENS HOME TD FD CONT FOP FOM TOM TOP SOM SOP LCOM LCOP LOEJ CLCONT SD DSCSNS 8EJ SOM SOP LCOM LCOP MD 8EJ HOME VDSENS REFOUT VD VD VD VD PGND PGND PGND DSCSNS GND GND SWVDD IC301 BA5839FP VR 1 OPIN2+ 2 OPIN2- 3 OPOUT2 4 5 OPIN1+ 6 OPIN1- 7 OPOUT1 29 FIN1 9 MUTE 10 PowVcc1 11 VO1- 12 VO1+ 13 VO2- 14 VO2+ 8 GND1 15 VO3+ 17 VO4+ 18 VO4- 19 PowVcc2 20 GND2 21 CNT 22 LDIN 23 OPOUTSL 24 OPINSL 25 OPOUT3 26 OPIN3- 27 OPIN3+ 28 PreVcc 16 VO3- 30 FIN2 NM TH201 C203 NM C708 NM C202 0.1u/10 0.1u/10 C303 4700p/25 C304 0.022u/16 C711 NM R203 NM (1608) R254 100k R256 100k R261 NM R307 18k R308 18k R310 18k R309 18k NM C305 C709 NM C710 NM C307 1u/10 (1608) R240 47k (1608) R241 10k FULL EMPTY TEMP CLCONT VDSENS MDX LOEJ TIN CONT HOME 8SNS TOM DSCSNS FOM FOP SIN TOP FIN CIN MDY RED GN WH BLK REFO2 NM S905 8EJ 1 NC 2 3 4 NC CSN1081-A S903 DSCSNS 1 NC 2 3 4 NC CSN1080-A S901 HOME 1 NC 2 3 4 NC 1 2 3 (RAM0) 4 (RAM1) 5 (RAM2) NC6 6 /8SNS 7 NC7 8 /HOME 9 /DSCSNS 10 VDSENS 11 TEMP 12 ADC.VDD 13 14 142 AD.VDD 143 AD.GND 144 RAM0 RAM1 RAM2 C293 1000p/50 R258 NM R259 0 NM C306 SWVDD C308 NM (1608) MOTOR DRIVER LOGIC TABLE LOAD EJ PLAY OFF CLCONT H H L L LOEJ L H - - CONT L L H L NOTE1) GND CD LSI , RFAMP , CPU PGND Actuator , Motor Driver AGND Audio These GND's are not connected to each other on PCB. PGND is connected to a floating mechanism part by a screw. Land for manual soldering SWITCHES: CD CORE UNIT S901:HOME SWITCH.........ON-OFF S903:DSCSNS SWITCH.....ON-OFF The underlined indicates the switch position. CXE2273 CXC4026 T F F T S S C C F T S C S S C C 1 2 3 4 6 7 8 9 d www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 58 1 2 3 4 1 2 3 4 C D F A B E 10.4 WAVEFORMS - CD CORE UNIT 1 2 3 DSCSNS 5 V/div 500 ms/div LOEJ 5 V/div HOME 5 V/div 12 cm CD Loading operation 12 cm CD Loading operation 12 cm CD-DA setup operation after loading Ref : GND Mode: Normal 12 cm CD-DA Source On setup operation Ref : REFO Mode: Normal Spindle waveform during play operation Ref : REFO Mode: Normal Track Open waveform Ref : REFO Mode: TEST 1 Track Jump waveform Ref : REFO Mode: TEST 4 Tracks Jump waveform Ref : REFO Mode: TEST Spindle waveform during play operation (Wider) Ref : REFO Mode: Normal Focus Search waveform Ref : REFO Mode: TEST Source On setup operation Ref : REFO Mode: Normal CD-DA Play operation Ref : REFO Mode: Normal Ref : GND Mode: Normal Ref : REFO Mode: Normal 1 4 2 5 DSCSNS 5 V/div 500 ms/div CLCONT 5 V/div LOEJ 5 V/div VD 10 V/div 6 7 8 SIN 1 V/div 1 s/div CIN 500 mV/div TIN 1 V/div 9 a 6 FIN 200 mV/div 500 ms/div RFOK(MONI_3) 2 V/div SIN 2 V/div b c TE 500 mV/div 200 ms/div FE 500 mV/div c 9 b 8 FE 500 mV/div 20 ms/div FIN 500 mV/div TE 500 mV/div TIN 500 mV/div d 6 MDX 2 V/div 200 ms/div SIN 500 mV/div b e TE 500 mV/div 2 ms/div RFAGC 500 mV/div d 6 MDX 2 V/div 5 µs/div SIN 500 m V/div 9 c FIN 500 mV/div 200 ms/div FE 500 mV/div e b 8 RFAGC 1 V/div 500 µs/div TE 500 mV/div TIN 500 mV/div e b 8 RFAGC 1 V/div 500 µs/div TE 500 mV/div TIN 500 mV/div Note : 1. The encircled numbers denote measuring points in the circuit diagram. 2. Reference voltage REFO1(1.65 V) www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 59 5 6 7 8 5 6 7 8 C D F A B E e b 8 RFAGC 1 V/div 500 µs/div TE 500 mV/div TIN 500 mV/div 10 Tracks Jump waveform 32 Tracks Jump waveform Search operation (Outter to Inner) Ref : REFO Mode: TEST Analog audio waveform Ref : AGND Mode: Normal 12 cm CD Eject operation Ref : GND Mode: Normal 12 cm CD Eject operation Ref : GND Mode: Normal Ref : REFO Mode: TEST Ref : REFO Mode: Normal e b 8 RFAGC 1 V/div 2 ms/div TE 500 mV/div TIN 500 mV/div e b 7 6 RFAGC 1 V/div 200 ms/div TE 1 V/div CIN 1 V/div SIN 2 V/div f g LOUT 1 V/div 200 µs/div ROUT 1 V/div Black dot (800 µm) during play Ref : REFO Mode: Normal e 8 b 9 RFAGC 1 V/div 500 µs/div TIN 1 V/div TE 1 V/div FIN 1 V/div 1 2 3 DSCSNS 5 V/div 500 ms/div LOEJ 5 V/div HOME 5 V/div 1 4 2 DSCSNS 5 V/div 500 ms/div CLCONT 5 V/div LOEJ 5 V/div www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 60 1 2 3 4 1 2 3 4 C D F A B E 11. PCB CONNECTION DIAGRAM 11.1 TUNER AMP UNIT A A TUNER AMP UNIT Capacitor Connector P.C.Board Chip Part SIDE B SIDE A NOTE FOR PCB DIAGRAMS 1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic dia- gram. 2.Viewpoint of PCB diagrams 1 5 1 1 1 1 5 1 1 R251 R252 R253 R254 R255 R256 R257 R258 JA251 C251 C252 C253 C254 C255 C256 C257 C258 C259 Q301 Q351 R301 R302 R303 R304 R331 C300 C302 C306 C312 C313 R351 R352 R353 R941 R942 C331 C335 C336 C337 JA941 P251 C351 C352 C941 C942 Q251 Q252 10 20 30 40 50 60 70 X 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0 Y F RCA C CN701 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 61 5 6 7 8 5 6 7 8 C D F A B E A SIDE A 1 E 1 1 5 5 1 10 1 5 10 1 1 1 5 10 15 20 1 E E 1 1 E E 1 5 10 15 20 1 5 1 5 10 15 5 1 10 1 5 E E E E E 1 5 10 15 20 25 0 1 5 1 1 R401 R404 R405 D751 R406 R407 R213 R408 R409 Q851 R601 R602 R603 R604 R410 R605 R411 D951 R412 R606 D952 R413 R607 R608 R609 R221 R222 R801 R802 R803 R804 R610 R805 R611 L851 R612 R806 CN402 R613 R615 JA401 R616 R617 R618 R619 R810 R812 CN602 R813 R814 Q680 R815 R817 R623 R818 R819 C201 IC951 C202 C203 C204 C205 CN801 C206 C207 R820 C401 C402 C403 C404 C405 C406 C212 C407 C213 C408 C214 C409 C215 C216 R831 C601 C602 C603 C410 C604 C411 C605 C606 C412 R643 C607 C413 C414 C608 C609 C415 C416 C417 C418 C419 C802 C803 C610 C804 C611 X601 C805 C612 C613 C614 C808 C615 C616 C617 C618 R655 C619 R656 R657 C810 R659 C811 C812 C813 C620 C814 C621 C815 R851 C816 C622 R852 C817 C623 R853 C818 R660 C624 R854 R661 C625 R855 R662 C626 R663 C627 C628 R665 C629 R666 C820 C821 C822 C630 C631 C632 C633 C634 C635 R672 C636 C637 R674 C638 R675 C639 R678 R679 C640 C641 C642 C643 R680 C644 R681 R682 C647 R683 R688 Q301 R689 ZNR401 C650 C651 C653 R691 R692 D601 D602 IC201 D805 C671 D806 C672 D807 IC601 C681 C682 C683 L902 L903 X681 Q921 R302 R304 Q751 Q752 D851 Q951 Q952 R701 R702 R703 R704 R708 U401 R331 R332 R333 R334 CN701 R916 C301 C302 C303 C304 C305 C306 C307 C308 C309 R921 JA901 R922 R923 R924 R925 C310 C311 C312 C314 C315 C702 C703 C704 C901 C902 C903 IC691 R751 C909 C331 C332 C333 C334 C910 C911 C335 C912 6 C913 7 C914 C915 R951 C916 R952 C917 R953 C918 C919 C920 C921 D301 D302 C751 C752 C753 L201 Q601 Q602 C951 C952 C953 C954 L401 L402 L403 Q801 Q802 Q803 IC301 D901 L601 D902 L602 L603 L604 C388 L605 L606 L607 L608 L609 L801 L802 L610 D911 L611 D912 L612 L613 L614 L615 L616 L617 L618 L619 L620 D921 L621 IC911 R201 VA801 VA802 R206 R207 0 70 80 90 100 110 120 130 140 150 160 FRONT B CN1801 FM/AM TUNER UNIT C CN701 POWER CONNECTOR ANTENNA P 251 (A,8,131) Fuse 3 A CEK1286 > 1 10 20 30 40 50 60 70 80 90 100 110 120 130 140 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 62 1 2 3 4 1 2 3 4 C D F A B E A A TUNER AMP UNIT 90 100 110 120 130 140 150 160 1 1 1 1 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 63 5 6 7 8 5 6 7 8 C D F A B E A SIDE B 10 20 30 40 50 60 70 80 90 X 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0 Y 1 1 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 64 1 2 3 4 1 2 3 4 C D F A B E 11.2 KEYBOARD UNIT B SIDE A B KEYBOARD UNIT 1 1 1 5 10 15 20 25 30 35 40 D1801 D1802 D1803 D1804 D1805 D1806 D1807 D1808 D1809 IC1802 D1810 JA1801 D1811 D1812 D1813 D1814 D1815 D1816 D1817 D1818 D1821 D1822 D1823 D1824 D1825 D1826 D1827 D1828 S1801 D1829 S1802 S1804 S1805 S1806 S1807 S1808 D1830 S1809 D1831 D1832 D1833 D1834 D1835 D1836 D1837 S1810 S1812 S1813 S1814 S1815 S1816 S1817 S1818 S1819 S1820 S1821 S1822 S1823 S1824 V1801 S1803 S1811 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 X 40 30 20 10 0 Y 160 1 AUX 6 5 4 3 2 1 CLK DOWN RIGHT UP SRC AUDIO EQ CD EJECT LEFT FUNC DISP BAND LCD www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 65 5 6 7 8 5 6 7 8 C D F A B E B SIDE B B KEYBOARD UNIT 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 X 40 30 20 10 0 Y 160 1 10 1 5 1 E 1 5 10 15 20 25 30 35 40 45 50 55 60 1 1 X1801 CN1801 VA1819 VA1820 C1801 C1802 C1803 C1804 C1805 Q1801 Q1802 R1801 R1802 R1803 R1804 R1805 R1806 R1807 R1808 IC1801 R1809 R1810 R1811 R1812 R1813 R1814 R1815 R1816 R1817 R1818 R1819 R1820 R1821 R1822 R1823 R1824 R1825 R1826 R1827 R1828 D1838 D1839 1 A CN801 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 66 1 2 3 4 1 2 3 4 C D F A B E 11.3 CD CORE UNIT(S11.1COMP) C SIDE A C CD CORE UNIT(S11.1COMP) 1 1 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 1 5 1 5 10 15 1 5 10 15 1 5 10 1 10 5 1 15 20 25 29 30 R221 R222 R225 R226 R234 R237 C201 C202 C203 C204 TH201 C206 R243 C207 C208 C211 X201 C213 C214 C216 C217 R254 C218 C219 R256 R258 R259 C220 C221 C224 R261 C226 C227 C240 C250 C251 IC201 IC202 R307 R308 R309 R310 CN101 R701 R702 C102 CN701 CN704 C303 C304 C307 C708 C711 S901 D101 IC301 R201 R202 R203 R204 10 20 30 40 50 60 70 X 60 50 40 30 20 10 0 Y PICKUP UNIT(P10.5 )(SERVICE) A CN701 M1 SPINDLE MOTOR M2 LOADING/CARRIAGE MOTOR HOME F E REFO2 www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 67 5 6 7 8 5 6 7 8 C D F A B E C SIDE B C CD CORE UNIT(S11.1COMP) 10 20 30 40 50 60 70 X 60 50 40 30 20 10 0 Y E E 1 1 E R210 R214 R216 R227 R228 R229 R232 R233 R235 R236 R240 R241 C205 R244 R245 C209 C210 C212 C215 C601 C602 C222 C223 C228 C229 C230 C236 C239 R291 Q101 Q102 C293 R101 R102 R103 R104 R106 R107 R108 C105 C106 C110 C111 C305 C306 C308 C701 C702 C703 C704 C705 C706 C707 C709 C710 C730 S903 S905 Q201 R206 8EJ DSCSNS www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 68 1 2 3 4 1 2 3 4 C D F A B E 12. ELECTRICAL PARTS LIST NOTE: Parts whose parts numbers are omitted are subject to being not supplied. The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Meaning of the figures and others in the parentheses in the parts list. Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board. IC 301 (A, 91, 111) IC NJM2068V Circuit Symbol and No. Part No. A : DEH-1300MP/XNUC B : DEH-1350MP/XNES C : DEH-1350MP/XNES1 D : DEH-1350MPG/XNES E : DEH-1350MP/XNCN5 F : DEH-1390MP/XNID Unit Number : QWM3162(A) : QWM3163(B,C,D,F) : QWM3164(E) Unit Name : Tuner Amp Unit Unit Number : Unit Name : Keyboard Unit Unit Number : CWX3957 Unit Name : CD CORE UNIT(S11.1Comp) A Unit Number : QWM3162(A) QWM3163(B,C,D,F) QWM3164(E) Unit Name : Tuner Amp Unit MISCELLANEOUS IC 201 (A,107,110) IC PML014B IC 301 (A,79,142) IC PAL007E IC 601 (A,122,84) IC PN5043A IC 911 (A,145,29) IC BA49181-V12 Q 251 (A,26,131) Chip Transistor RN1910 Q 351 (A,36,132) Chip Transistor RN4983 Q 602 (A,136,58) Chip Transistor 2SC5868 Q 751 (A,142,140) Transistor 2SD2396 Q 752 (A,139,134) Chip Transistor RN4983 Q 802 (A,112,38) Transistor LTC114EUB Q 803 (A,117,42) Transistor LSA1576UB Q 921 (A,127,106) Transistor LSC4081UB D 301 (A,97,128) Diode CRG03 D 302 (A,99,128) Diode CRG03 D 751 (A,137,134) Diode RKZ8.2KG(B2) D 901 (A,138,126) Diode 1SR154-400 D 902 (A,136,126) Diode 1SR154-400 D 911 (A,130,52) Diode CRG03 D 912 (A,130,49) Diode CRG03 D 921 (A,132,106) Diode RKZ6.8KG(B2) L 401 (A,140,58) Inductor LCTAW2R2J2520 L 403 (A,153,63) Inductor CTF1473 L 602 (A,126,99) Inductor CTF1473 L 604 (A,131,69) Chip Coil LCTAW1R0J2520 L 607 (A,137,83) Inductor CTF1379 L 608 (A,138,73) Chip Coil LCTAW1R5J2520 L 609 (A,139,71) Chip Coil LCTAW1R5J2520 L 610 (A,141,77) Inductor LCTAW1R2J2520 L 611 (A,143,72) Inductor CTF1379 L 612 (A,142,70) Inductor CTF1379 L 613 (A,137,81) Inductor CTF1379 L 614 (A,127,70) Inductor CTF1379 L 617 (A,137,86) Inductor CTF1389 L 621 (A,139,83) Inductor CTF1389 L 902 (A,113,142) Choke Coil 600 uH CTH1432 ZNR401 (A,152,113) Surge Protector IMSA-6802-01Y900 X 601 (A,146,79) Oscillator 74.1 MHz CSS1758 X 681 (A,119,63) Oscillator 4.718 6 MHz CSS1796 >P251 (A,8,131) Fuse 3 A CEK1286 VA801 (A,102,14) Varistor EZJP0V270RM VA802 (A,105,14) Varistor EZJP0V270RM U 401 (A,158,106) FM/AM Tuner Unit CWE2256 CN701 (A,92,39) Connector VKN1191 CN801 (A,110,4) Connector CKS6231 JA251 (A,19,139) Pin Jack CKB1056 JA401 (A,158,129) Antenna Jack YKS5041 JA901 (A,114,142) Plug CKM1586 > Fuse 10 A YEK5001 RESISTORS R 206 (A,95,112) RS1/16SS681J Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 69 5 6 7 8 5 6 7 8 C D F A B E R 207 (A,95,108) RS1/16SS681J R 213 (A,95,110) RS1/16SS331J R 221 (A,95,109) RS1/16SS223J R 222 (A,95,111) RS1/16SS223J R 251 (A,24,131) RS1/16SS223J R 252 (A,29,131) RS1/16SS223J R 253 (A,31,131) RS1/16SS821J R 254 (A,22,131) RS1/16SS821J R 303 (A,61,131) RS1/16SS153J R 351 (A,59,129) RS1/16SS103J R 352 (A,59,132) RS1/16SS153J R 353 (A,59,130) RS1/16SS221J R 404 (A,134,95) RS1/16SS102J R 405 (A,153,65) RS1/16SS102J R 406 (A,141,92) RS1/16SS102J R 407 (A,141,91) RS1/16SS102J R 408 (A,145,93) RAB4CQ104J R 409 (A,136,93) RS1/16SS391J R 410 (A,136,92) RS1/16SS681J R 411 (A,138,92) RS1/16SS681J R 412 (A,136,91) RS1/16SS681J R 413 (A,137,90) RS1/16SS472J R 601 (A,108,91) RS1/16SS473J R 603 (A,100,70) RS1/16SS473J R 604 (A,138,88) RS1/16SS681J R 606 (A,129,62) RS1/16SS473J R 608 (A,136,79) RS1/16SS470J R 610 (A,134,70) RS1/16SS473J R 611 (A,136,77) RS1/16SS182J R 612 (A,98,115) RS1/16SS563J R 613 (A,135,86) RS1/16SS302J R 615 (A,97,104) RS1/16SS563J R 616 (A,134,98) RS1/16SS104J R 617 (A,121,97) RS1/16SS473J R 618 (A,134,96) RS1/16SS473J R 619 (A,134,97) RS1/16SS104J R 643 (A,133,100) RS1/16SS104J R 656 (A,103,72) RS1/16SS104J R 657 (A,102,75) RS1/16SS104J R 659 (A,103,71) RS1/16SS472J R 660 (A,102,73) RS1/16SS472J R 661 (A,108,84) RS1/16SS221J R 662 (A,109,83) RS1/16SS221J R 663 (A,109,82) RS1/16SS221J R 666 (A,141,90) RS1/16SS103J R 672 (A,113,71) RS1/16SS104J R 674 (A,106,97) RS1/16SS104J R 675 (A,98,70) RS1/16SS473J R 678 (A,94,100) RS1/16SS103J R 679 (A,104,101) RS1/16SS103J R 680 (A,106,94) (A,B,C,D,F) RS1/16SS473J (A,106,94) (E) RS1/16SS123J R 681 (A,106,95) (A) RS1/16SS332J (A,106,95) (E) RS1/16SS333J R 682 (A,110,97) RAB4CQ104J R 683 (A,100,77) RS1/16SS473J R 689 (A,98,75) RS1/16SS0R0J R 702 (A,94,74) RS1/16SS221J R 704 (A,96,49) RS1/16SS221J R 708 (A,93,50) RS1/16SS104J R 751 (A,141,134) RS1/4SA271J Circuit Symbol and No. Part No. R 802 (A,119,42) RS1/16SS103J R 803 (A,111,40) RS1/16SS472J R 804 (A,109,14) RS1/10SR101J R 805 (A,117,14) RS1/10SR101J R 810 (A,99,19) RS1/10SR222J R 812 (A,103,19) RS1/10SR222J R 813 (A,100,19) RS1/10SR222J R 814 (A,105,19) RS1/10SR222J R 815 (A,102,19) RS1/10SR222J R 817 (A,121,23) RS1/16SS473J R 818 (A,99,70) RS1/16SS104J R 819 (A,120,19) RS1/10SR102J R 820 (A,108,40) RS1/16SS103J R 921 (A,125,104) RS1/16SS104J R 922 (A,130,108) RS1/16SS223J R 923 (A,121,116) RS1/4SA102J R 924 (A,133,108) RS1/16SS473J R 925 (A,129,106) RS1/16SS473J CAPACITORS C 201 (A,99,105) CKSRYB105K10 C 202 (A,98,116) CKSRYB105K10 C 203 (A,98,106) CKSRYB105K10 C 204 (A,98,114) CKSRYB105K10 C 205 (A,93,105) 10 uF CCG1192 C 206 (A,98,112) CKSRYB105K10 C 207 (A,98,108) CKSRYB105K10 C 212 (A,98,111) CKSRYB105K10 C 213 (A,98,109) CKSRYB105K10 C 214 (A,115,107) 4.7 uF CCG1201 C 216 (A,111,103) CCSSCH100D50 C 253 (A,48,131) 10 uF CCG1192 C 254 (A,31,128) 10 uF CCG1192 C 300 (A,36,138) CKSRYB103K50 C 301 (A,76,130) CKSRYB474K10 C 302 (A,75,130) CKSRYB474K10 C 303 (A,80,130) CKSRYB474K10 C 304 (A,81,130) CKSRYB474K10 C 305 (A,76,133) CKSRYB474K10 C 306 (A,75,133) CKSRYB474K10 C 307 (A,80,133) CKSRYB474K10 C 308 (A,81,133) CKSRYB474K10 C 309 (A,88,128) 2.2 uF CCG1205 C 310 (A,90,128) 2.2 uF CCG1205 C 312 (A,69,130) CEVW100M16 C 352 (A,55,132) 10 uF CCG1192 C 388 (A,79,119) CKSSYB102K50 C 402 (A,147,97) CKSSYB103K16 C 406 (A,153,59) CCSSCH390J50 C 414 (A,153,57) CCSSCH470J50 C 418 (A,152,98) 10 uF CCG1192 C 601 (A,104,89) CKSRYB105K10 C 602 (A,109,88) CKSSYB103K16 C 604 (A,149,69) CCSRCH8R0D50 C 605 (A,118,70) CKSSYB104K10 C 607 (A,122,71) CKSSYB104K10 C 609 (A,134,67) CKSSYB331K50 C 610 (A,139,44) Capacitor CEVW101M4 C 611 (A,134,65) CKSSYB331K50 Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 70 1 2 3 4 1 2 3 4 C D F A B E C 612 (A,124,70) CKSSYB104K10 C 613 (A,103,55) Capacitor CEVW471M10 C 614 (A,152,93) CKSSYB102K50 C 615 (A,134,68) CKSSYB331K50 C 616 (A,129,71) CKSSYB103K16 C 617 (A,134,73) CKSSYB104K10 C 621 (A,139,61) CKSSYB331K50 C 623 (A,136,76) CKSSYB102K50 C 624 (A,135,75) CKSSYB102K50 C 625 (A,139,75) CCSSCH270J50 C 626 (A,139,69) CCSSCH270J50 C 627 (A,141,72) CCSSCH150J50 C 628 (A,139,79) CKSSYB102K50 C 629 (A,137,78) CCSSCH4R0C50 C 630 (A,139,77) CCSSCH8R0D50 C 631 (A,123,68) CKSSYB223K16 C 632 (A,106,96) CKSSYB104K10 C 633 (A,125,97) CKSSYB104K10 C 635 (A,139,89) CKSSYB104K10 C 637 (A,130,64) CKSSYB103K16 C 640 (A,127,71) CKSSYB103K16 C 643 (A,141,81) CKSSYB104K10 C 644 (A,137,61) CKSSYB102K50 C 651 (A,102,89) CCSSCH270J50 C 653 (A,106,73) CCSSCH100D50 C 671 (A,96,104) CKSSYB182K50 C 672 (A,96,115) CKSSYB182K50 C 681 (A,119,66) CCSSCH270J50 C 682 (A,121,66) CCSSCH270J50 C 702 (A,98,40) CKSSYB103K16 C 703 (A,90,50) CKSSYB104K10 C 751 (A,135,133) CKSSYB473K16 C 752 (A,147,131) CEVW101M16 C 802 (A,112,19) CKSSYB104K10 C 803 (A,117,19) CCSSCH221J50 C 804 (A,108,19) CCSSCH221J50 C 805 (A,112,14) CKSSYB104K10 C 808 (A,108,14) CKSSYB105K6R3 C 810 (A,104,14) CCSSCH221J50 C 811 (A,101,14) CCSSCH221J50 C 812 (A,108,37) CKSSYB104K16 C 818 (A,116,14) CKSSYB104K10 C 820 (A,97,22) CKSSYB104K10 C 821 (A,124,19) CKSSYB104K10 C 822 (A,121,18) CCSSCH221J50 C 901 (A,133,126) 3 300 uF/16 V CCH1732 C 902 (A,142,124) CKSRYB104K16 C 912 (A,148,52) 1 000 uF/16 V XCH3021 C 915 (A,149,41) 4.7 uF CCG1201 C 917 (A,134,48) CKSSYB102K50 B Unit Number : Unit Name : Keyboard Unit MISCELLANEOUS IC 1801 (B,86,24) IC PD6340A IC 1802 (A,156,23) Remote IC GP1UXC14RK D 1801 (A,68,22) White LED SMLXA4WBETW1(Z1) Circuit Symbol and No. Part No. D 1802 (A,6,34) LED(A,B,C) SML-D12V8W(PQ) (A,6,34) LED(D,E,F) SML-D12P8W(KL) D 1803 (A,6,22) LED(A,B,C) SML-D12V8W(PQ) (A,6,22) LED(D,E,F) SML-D12P8W(KL) D 1804 (A,8,11) LED(A,B,C) SML-D12V8W(PQ) (A,8,11) LED(D,E,F) SML-D12P8W(KL) D 1805 (A,11,41) LED(A,B,C) SML-D12V8W(PQ) (A,11,41) LED(D,E,F) SML-D12P8W(KL) D 1806 (A,143,8) LED(A,B,C) SML-D12V8W(PQ) (A,143,8) LED(D,E,F) SML-D12P8W(KL) D 1807 (A,131,7) LED(A,B,C) SML-D12V8W(PQ) (A,131,7) LED(D,E,F) SML-D12P8W(KL) D 1808 (A,119,7) LED (A,B,C) SML-D12V8W(PQ) (A,119,7) LED(D,E,F) SML-D12P8W(KL) D 1809 (A,107,6) LED(A,B,C) SML-D12V8W(PQ) (A,107,6) LED(D,E,F) SML-D12P8W(KL) D 1810 (A,71,5) LED(A,B,C) SML-D12V8W(PQ) (A,71,5) LED(D,E,F) SML-D12P8W(KL) D 1811 (A,83,6) LED(A,B,C) SML-D12V8W(PQ) (A,83,6) LED(D,E,F) SML-D12P8W(KL) D 1812 (A,95,6) LED(A,B,C) SML-D12V8W(PQ) (A,95,6) LED(D,E,F) SML-D12P8W(KL) D 1813 (A,25,32) LED(A,B,C) SML-D12V8W(PQ) (A,25,32) LED(D,E,F) SML-D12P8W(KL) D 1814 (A,54,8) LED(A,B,C) SML-D12V8W(PQ) (A,54,8) LED(D,E,F) SML-D12P8W(KL) D 1815 (A,59,18) LED(A,B,C) SML-D12V8W(PQ) (A,59,18) LED(D,E,F) SML-D12P8W(KL) D 1816 (A,54,29) LED (A,B,C) SML-D12V8W(PQ) (A,54,29) LED(D,E,F) SML-D12P8W(KL) D 1817 (A,17,21) LED(A,B,C) SML-D12V8W(PQ) (A,17,21) LED(D,E,F) SML-D12P8W(KL) D 1818 (A,21,10) LED(A,B,C) SML-D12V8W(PQ) (A,21,10) LED(D,E,F) SML-D12P8W(KL) X 1801 (B,75,22) Ceramic Resonator 5.00 MHz CSS1547 S 1824 (A,39,18) Encoder CSD1168 VA1819 (B,149,21) Varistor EZJZ1V270RM VA1820 (B,139,8) Varistor EZJZ1V270RM CN1801 (B,108,9) Connector CKS6230 JA1801 (A,153,7) Jack CKN1082 V 1801 (A,143,32) LCD CAW2008 RESISTORS R 1801 (B,144,25) RS1/10SR2R2J R 1802 (B,69,18) RS1/10SR222J R 1803 (B,69,16) RS1/10SR222J R 1806 (B,153,29) RS1/10SR101J R 1807 (B,56,12) RS1/4SA271J R 1808 (B,21,15) (A,B,C) RS1/4SA102J (B,21,15) (D,E,F) RS1/4SA391J R 1809 (B,137,23) (A,B,C) RS1/4SA182J (B,137,23) (D,E,F) RS1/4SA391J R 1810 (B,61,13) (A,B,C) RS1/4SA272J (B,61,13) (D,E,F) RS1/4SA561J R 1811 (B,51,12) (A,B,C) RS1/4SA272J (B,51,12) (D,E,F) RS1/4SA561J R 1812 (B,17,19) (A,B,C) RS1/4SA272J (B,17,19) (D,E,F) RS1/4SA561J R 1813 (B,57,24) RS1/10SR0R0J Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com DEH-1300MP/XNUC 71 5 6 7 8 5 6 7 8 C D F A B E R 1823 (B,49,30) RS1/10SR473J R 1828 (B,58,13) RS1/4SA271J CAPACITORS C 1801 (B,97,24) CKSRYB105K10 C 1802 (B,153,25) 10 uF CCG1192 C 1803 (B,137,7) CKSRYB104K16 C 1804 (B,134,6) CKSRYB472K50 C 1805 (B,134,4) CKSRYB472K50 C Unit Number: CWX3957 Unit Name : CD CORE UNIT(S11.1Comp) MISCELLANEOUS IC 201 (A,32,34) IC PE5746A IC 301 (A,65,28) IC BA5839FP Q 101 (B,10,57) Transistor 2SA1577 Q 102 (B,20,48) Chip Digital Transistor LTA123JUB X 201 (A,41,21) Ceramic Resonator 16.934 MHz CSS1603 S 901 (A,43,54) Spring Switch(HOME) CSN1080 S 903 (B,22,13) Spring Switch(DSCSNS) CSN1081 CN101 (A,17,59) Connector CKS4808 CN701 (A,38,11) Connector CKS4808 RESISTORS R 101 (B,6,60) RS1/10SR2R4J R 102 (B,8,60) RS1/10SR2R4J R 103 (B,9,60) RS1/10SR2R7J R 104 (B,13,53) RS1/16SS222J R 107 (B,18,49) RS1/16SS105J R 202 (A,48,26) RS1/16SS473J R 204 (A,23,20) RS1/16SS221J R 206 (B,32,28) RS1/16SS104J R 210 (B,52,13) RS1/16SS102J R 214 (B,29,49) RS1/16SS472J R 216 (B,30,48) RS1/16SS472J R 221 (A,32,50) RS1/16SS103J R 222 (A,34,50) RS1/16SS103J R 225 (A,29,49) RS1/16SS103J R 226 (A,28,49) RS1/16SS393J R 227 (B,26,46) RS1/16SS562J R 228 (B,24,43) RS1/16SS122J R 229 (B,24,45) RS1/16SS472J R 232 (B,26,44) RS1/16SS122J R 233 (B,20,25) RS1/16SS103J R 234 (A,50,19) RS1/16SS473J R 235 (B,25,33) RS1/16SS473J R 237 (A,43,23) RS1/16SS471J R 240 (B,50,11) RS1/16S473J R 241 (B,50,12) RS1/16SS103J R 244 (B,28,29) RS1/16SS473J R 254 (A,20,23) RS1/16SS104J R 256 (A,19,23) RS1/16SS104J R 259 (A,13,24) RS1/16SS0R0J R 291 (B,17,45) RS1/16SS272J R 307 (A,61,34) RS1/16SS183J R 308 (A,61,36) RS1/16SS183J R 309 (A,59,34) RS1/16SS183J Circuit Symbol and No. Part No. R 310 (A,58,37) RS1/16SS183J R 701 (A,37,22) RS1/16SS221J R 702 (A,23,23) RS1/16SS221J CAPACITORS C 106 (B,13,55) CKSQYB475K6R3 C 202 (A,21,27) CKSSYB104K10 C 204 (A,22,21) CKSSYB103K16 C 205 (B,37,25) CKSQYB475K6R3 C 206 (A,38,23) CKSSYB104K10 C 207 (A,41,24) CKSRYB104K16 C 209 (B,44,33) CEVW220M6R3 C 210 (B,41,28) CKSSYB104K10 C 211 (A,43,27) CKSSYB104K10 C 213 (A,39,45) CKSSYB104K10 C 214 (A,45,28) CKSSYB104K10 C 215 (B,39,32) CKSSYB104K10 C 216 (A,27,50) CKSSYB332K50 C 217 (A,27,47) CKSSYB104K10 C 218 (A,27,49) CKSSYB473K16 C 219 (A,25,45) CKSSYB104K10 C 220 (A,25,46) CKSSYB182K50 C 221 (A,24,44) CKSSYB104K10 C 222 (B,24,44) CCSSCH560J50 C 223 (B,24,46) CCSSCH4R0C50 C 224 (A,23,43) CKSSYB104K10 C 226 (A,19,42) CCSSCH680J50 C 227 (A,19,40) CCSSCH470J50 C 228 (B,17,43) CKSSYB103K16 C 229 (B,24,38) CKSSYB104K10 C 236 (B,26,38) CKSSYB104K10 C 239 (B,26,45) CCSSCH220J50 C 240 (A,17,37) CKSSYB104K10 C 250 (A,32,51) CKSSYB102K50 C 251 (A,34,51) CKSSYB102K50 C 293 (B,17,44) CKSSYB102K50 C 303 (A,61,35) CKSSYB472K25 C 304 (A,59,35) CKSSYB223K16 C 307 (A,69,21) CKSRYB105K10 C 703 (B,37,15) CCSSCH101J50 C 704 (B,41,14) CKSSYB102K50 Miscellaneous Parts List M 1 Motor Unit(SPDL) CXE2273 M 2 Motor Unit(LOAD/CRG) CXC4026 Pickup Unit(P10.5)(Service) CXX1942 Circuit Symbol and No. Part No. www. xiaoyu163. com QQ 376315150 9 9 2 8 9 4 2 9 8 TEL 13942296513 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3 Q Q TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299 http://www.xiaoyu163.com