19" LCD Color Monitor Chassis: HUDSON 8 Service Service Service 190S8FS/00 190S8FB/00 190S8FB/27 Description Page Description Page SAFETY NOTICE ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING Table Of Contents........................................………….1 Revision List................................................…………….2 Important Safety Notice………….................................3 1. Monitor Specifications……...................................…..4 2. LCD Monitor Description………..…….........................6 3. Operation instructions…………….......................…....7 3.1General Instructions…………………..…..…………7 3.2 Control buttons…………..……………………………7 3.3 Adjusting the Picture……....................................…..9 3.4 Connecting to the PC ….........…….…........……....11 4. Input/Output Specification.........................………….12 4.1 Input Signal Connector...........................…………..12 4.2 Factory Preset Display Modes...............................13 4.3 Pixel Defect Policy……………………………………13 4.4 Failure Mode OF Panel………………………..…..16 5. Block Diagram……………………………................17 5.1 Software Flow Chart............................………….....17 5.2 Electrical Block Diagram..................……….........19 6. Schematic Diagram…….....................……….........21 6.1 Main Board…….……………..….……………………21 6.2 Power Board…………………………..…………………25 6.3 Key Board………...………………………………………27 7. PCB Layout.....……......................……………………..28 7.1 Main Board.....…….......................……..…………......28 7.2 Power Board.……................…..…………….............30 7.3 Key Board………...………………………………………32 8. Wiring Diagram……………………………………….…..33 9. Mechanical Instructions.....……...…………..…..........34 10.Trouble shooting…..…………………………...……..44 11. Repair Flow Chart…….…….……………………………46 12. ISP Instructions..…..........................………..............52 13. DDC Instructions……......…….............….................59 14. White Balance, Luminance Adjustment……............73 15. Monitor Exploded View………..…….………..............75 16. Recommended & Spare Parts List.…………...............76 17. Different Parts List...……….....………....................90 18. General Product Specification………………………….91 312278517300 REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES Published by Philips CE Copyright reserved Subject to modification ○ K Jul, 05, 2007 GB http://www.wjel.net 2 HUDSON 8 Revision List Version Release Date Revision History A00 Jul.5, 2007 Initial release, Draft Version A01 Jul.16,2007 Add new BOM in Item 17 A02 Nov.07, 2007 Update C907 in Item 16 A03 Nov.25,2007 Add Philips 12NC for 715GT039 A A04 Mar.05,2008 Add 056G1133 24 1 as second source for U204 A05 Mar.14,2008 Add 2nd panel in Item 16 A06 Mar.18,2008 PWPC7942GQA8 replace PWPC942GR1P A07 Apr.05,2008 Add 2nd source 87G 501 32 DL for CN901 Add a new BOM for CTV Model 190S8FS/00 in Item16 A08 Apr.12,2008 Add a new BOM for CTV Model 190S8FB/00 in Item17 A09 July.03.2008 Add A33G0236 VB 1L0118 for COVER_HINGE http://www.wjel.net 3 HUDSON 8 Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Philips Company Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended. It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Philips could not possibly know, evaluate and advise the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Philips has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Philips must first satisfy himself thoroughly that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected. Hereafter throughout this manual, Philips Company will be referred to as Philips. WARNING Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock, fire, or other hazards. Under no circumstances should the original design be modified or altered without written permission from Philips. Philips assumes no liability, express or implied, arising out of any unauthorized modification of design. Servicer assumes all liability. FOR PRODUCTS CONTAINING LASER: DANGER-Invisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM. CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION -The use of optical instruments with this product will increase eye hazard. TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF THIS SERVICE MANUAL. Take care during handling the LCD module with backlight unit -Must mount the module using mounting holes arranged in four corners. -Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen. -Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to the panel. -Protect the module from the ESD as it may damage the electronic circuit (C-MOS). -Make certain that treatment person’s body is grounded through wristband. -Do not leave the module in high temperature and in areas of high humidity for a long time. -Avoid contact with water as it may a short circuit within the module. -If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may damage the panel.) http://www.wjel.net 4 HUDSON 8 1. Monitor Specifications http://www.wjel.net 5 HUDSON 8 http://www.wjel.net 6 HUDSON 8 2. LCD Monitor Description The LCD monitor will contain a main board, a power board and a key board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage. Monitor Block Diagram AC-IN 100V-240V Power board (Include: adapter, inverter) Flat Panel and CCFL backlight Main Board RS232 Connector For white balance adjustment in factory mode CCFL Drive. Video signal, DDC Key Board HOST Computer http://www.wjel.net 7 HUDSON 8 3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at the front of the panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. - The power cord should be connected. - Connect the video cable from the monitor to the video card. - Press the power button to turn on the monitor, the power indicator will light up. 3.2 Control Buttons Front View http://www.wjel.net 8 HUDSON 8 Rear View http://www.wjel.net 9 HUDSON 8 3.3 Adjusting the Picture Description of the On Screen Display On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display interface is shown as below: In the OSD shown above users can press buttons at the front bezel of the monitor to move the cursor, to confirm the choice or change. To Lock/Unlock OSD function (User Mode) The OSD function can be locked by pressing “MENU” button for more than 10 seconds. Locked OSD function can be released by pressing “MENU” button for more than 10 seconds again. http://www.wjel.net 10 HUDSON 8 The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on. http://www.wjel.net 11 HUDSON 8 3.4 Connecting to the PC 1) Connect the power cord to the back of the monitor firmly. (Philips has pre-connected VGA cable for the first installation. 2) Connect to PC (a) Turn off your computer and unplug its power cable. (b) Connect the monitor signal cable to the video connector on the back of your computer. (c) Plug the power cord of your computer and your monitor into a nearby outlet. (d) Turn on your computer and monitor. If the monitor displays an image, installation is complete. http://www.wjel.net 12 HUDSON 8 4. Input/Output Specification 4.1 Input Signal Connector Analog connectors Pin No. Description Pin No. Description 1. Red video input 9. DDC +5V 2. Green video input 10. Logic Ground 3. Blue video input 11. Ground 4. Sense (GND) 12. Serial data line (SDA) 5. Cable detect (GND) 13. H. Sync 6. Red video ground 14. V. Sync 7. Green video ground 15. Data clock line (SCL) 8. Blue video ground VGA connector layout DVI connectors Pin No. Description Pin No. Description Pin No. Description 1. T.M.D.S Data2- 9. T.M.D.S Data1- 17. T.M.D.S Data0- 2. T.M.D.S Data2/4+ 10. T.M.D.S Data1/3+ 18. T.M.D.S Data0+ 3. T.M.D.S Data2 Shield 11. T.M.D.S Data1 Shield 19. T.M.D.S Data0/5 Shield 4. No connector 12. No connector 20. No connector 5. No connector 13. No connector 21. No connector 6. DDC Clock 14. +5V Power 22. T.M.D.S Clock Shield 7. DDC Data 15. Ground (for +5V) 23. T.M.D.S Clock+ 8. No connector 16. Hot Plug Detection 24. T.M.D.S Clock- http://www.wjel.net 13 HUDSON 8 4.2 Factory Preset Display Modes 4.3 Pixel Defect Policy http://www.wjel.net 14 HUDSON 8 http://www.wjel.net 15 HUDSON 8 http://www.wjel.net 16 HUDSON 8 4.4 Failure Mode Of Panel �� Failure description Phenomenon Vertical block defect Vertical dim lines Vertical lines defect (Always bright or dark) Horizontal block defect Horizontal dim lines Horizontal lines defect (Always bright or dark) Has bright or dark pixel Polarizer has bubbles Polarizer has bubbles Foreign material inside polarizer. It shows liner or dot shape. Concentric circle formed Bottom back light of LCD is brighter than normal Back light un-uniformity Backlight has foreign material. Black or white color, liner or circular type Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical instruction on this manual to eliminate failure by replace LCD panel. http://www.wjel.net 17 HUDSON 8 5. Block Diagram 5.1 Software Flow Chat 1 2 N Y 5 Y N 10 Y N 12 Y N 7 Y N 6 4 3 8 9 14 11 13 Y N 15 Y N 16 17 19 Y N 18 http://www.wjel.net 18 HUDSON 8 1) MCU initialize. 2) Is the EPROM blank? 3) Program the EPROM by default values. 4) Get the PWM value of brightness from EPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode. 9) Save the power key status into EPROM. Turn on the LED and set it to green color. Scalar initializes. 10) In standby mode? 11) Update the lifetime of back light. 12) Check the analog port, are there any signals coming? 13) Does the scalar send out an interrupt request? 14) Wake up the scalar. 15) Are there any signals coming from analog port? 16) Display "No connection Check Signal Cable" message. And go into standby mode after the message disappear. 17) Program the scalar to be able to show the coming mode. 18) Process the OSD display. 19) Read the keyboard. Is the power key pressed? http://www.wjel.net 19 HUDSON 8 5.2 Electrical Block Diagram 5.2.1 Main Board Panel Interface (CN402) Crystal 12.000MHZ (X201) Keypad Interface (CN407) Scalar NT68665MFG (Include MCU, ADC, OSD) (U203) D-Sub Connector (CN101) RGB H sync V sync VGA_SDA, VGA SCL DVI Connector (CN102) D-Data D-Clock DVI_SDA, DVI_SCL EEPROM M24C16 (U204) http://www.wjel.net 20 HUDSON 8 5.2.2 Inverter/Power Board DIM EMI filter Start Circuit: R905 Transformer AC input 12V ON/OFF Control Transformer MOSFET Lamp ON/OFF 5V Bridge Rectifier and Filter Feedback Circuit Rectifier diodes CN902 Output Circuit PWM Control IC （IC801） Over Voltage Feedback Circuit PWM Control IC （IC901） http://www.wjel.net 21 HUDSON 8 6. Schematic 6.1 Main Board 715G2561-1 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 A A B B C C D D E E F F G G H H EXT_EDID U101 U102 24C02 24C02 NC NC INT_EDID Q201 NC 3906 R206 NC 4.7K NC D201 BAV70 FB201 120 NC CN101 F3 CN102 A1 C101 E4 C102 A8 C103 A9 C104 A10 C105 A11 C106 A4 C107 A5 C110 B8 C111 B9 C112 B10 C113 B11 C114 C4 C115 E3 C116 C8 C117 C9 C118 C10 C121 E6 C122 F6 C123 F6 C124 F6 C125 G6 C126 G6 C127 G1 C128 G1 C129 G6 C130 H4 C131 C7 C132 C3 D101 A9 D102 A6 D103 A7 D104 A8 D105 A10 D106 B7 D107 B8 D108 B9 D109 B10 D110 D3 D111 C8 D112 C9 D113 C10 FB101 A3 FB102 E4 FB103 E5 FB104 F5 FB105 G2 FB106 G5 FB107 A6 R101 G4 R102 C7 R103 A5 R104 A5 R105 A4 R106 A2 R107 A2 R108 B3 R109 B3 R110 B2 R111 B2 R113 B2 R115 B2 R116 B2 R117 C2 R118 C2 R120 C4 R122 C2 R123 E2 R124 E2 R125 E2 R126 E6 R127 E2 R128 E2 R129 F6 R131 F6 R132 F6 R133 G6 R134 G1 R135 G6 R136 G1 R138 G6 R139 G5 R140 G5 R141 G2 R142 G2 R144 H4 U101 B5 U102 E3 ZD101 G3 ZD102 C7 ZD103 A2 ZD104 B2 ZD105 F3 ZD106 G2 ZD107 G2 DVI/D-SUB RX1M RX2P RX1P RX2M RXCP RX0M RX0P RXCM G R B B R G DDCSDA VIN DDCSCL DDCSCL_D RX0P RX1P RX2P RX1M DDCSDA_D RX0M RXCP RXCM RX2M VGA_SDA RIN+ RIN- SOG GIN+ GIN- BIN+ BIN- VGA_CABLE VS VGA_SCL HS DDC_WP RX2+ 3 DVI_SCL 3 RX2- 3 RX1- 3 RX0- 3 DVI-HPD 3 RX0+ 3 DVI_CABLE 3 RXC- 3 DDC_WP 3 RX1+ 3 DVI_SDA 3 RXC+ 3 +5V_ESD +5V_ESD +5V_ESD +5V VGA_5V VGA_5V VGA_VDD +5V DVI_5V DVI_5V DVI_VDD +5V R132 100R 1/16W C113 0.1uF 16V R127 100R 1/16W C118 0.1uF 16V R128 100R 1/16W C106 0.1uF 16V C131 1000pF R113 1K 1/16W D105 BAV99 3 1 2 D111 BAV99 3 1 2 C125 0.047uF C102 0.1uF 16V R116 10R 1/16W R134 100R 1/16W FB105 0R05 1/8W C127 330pF 50V CN102 JACK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26 25 C1 C2 C3 C4 C5 RX2- RX2+ GND RX4- RX4+ SCL SDA VS RX1- RX1+ GND RX3- RX3+ 5V GND HP RX0- RX0+ GND RX5- RX5+ GND RXC+ RXC- 26 25 RED GRN BLU HS GND D107 BAV99 3 1 2 ZD105 RLZ5.6B R125 NC R117 10R 1/16W R107 10R 1/16W D101 BAV99 3 1 2 CN101 DB15 1 6 2 7 3 8 4 9 5 11 12 13 14 15 10 17 16 R122 1K 1/16W D112 BAV99 3 1 2 C121 0.047uF R129 150� 1/16W C132 470PF 50V C111 0.1uF 16V R124 4K7 1/16W C115 1uF 16V C104 0.1uF 16V R118 10R 1/16W C126 0.047uF R108 100R 1/16W C122 0.047uF D104 BAV99 3 1 2 R139 75R 1/16W D109 BAV99 3 1 2 ZD106 RLZ5.6B R103 4K7 1/16W C129 0.047uF FB106 30 OHM 1 2 C114 0.1uF 16V D113 BAV99 3 1 2 R144 1K 1/16W ZD107 RLZ5.6B D108 BAV99 3 1 2 FB102 120 OHM 1 2 FB104 30 OHM 1 2 C123 1000pF R105 NC R141 2K2 1/16W D103 BAV99 3 1 2 C116 0.1uF 16V C112 0.1uF 16V FB103 30 OHM 1 2 ZD102 RLZ5.6B C117 0.1uF 16V ZD104 RLZ5.6B C105 0.1uF 16V R131 390R 1/16W R126 100R 1/16W R140 75R 1/16W U102 NC 1 2 3 4 5 6 7 8 NC/NC/NC/E0/E0 NC/NC/E1/E1/E1 NC/E2/E2/E2/E2 VSS SDA SCL WC VCC C107 1uF 16V R136 100R 1/16W R110 10R 1/16W D102 BAV70 C128 33pF R123 4K7 1/16W D106 BAV99 3 1 2 R138 150� 1/16W ZD101 RLZ5.6B R120 1K 1/16W R142 2K2 1/16W R109 100R 1/16W R111 10R 1/16W R106 10R 1/16W FB107 120 OHM 1 2 R133 150� 1/16W R102 1K 1/16W FB101 120 OHM 1 2 ZD103 RLZ5.6B R135 100R 1/16W C110 0.1uF 16V R101 75R 1/16W C124 0.047uF C101 0.1uF 16V C103 0.1uF 16V D110 BAV70 C130 0.1uF 16V R104 4K7 1/16W R115 10R 1/16W U101 NC/M24C02-WMN6TP 1 2 3 4 5 6 7 8 NC/NC/NC/E0/E0 NC/NC/E1/E1/E1 NC/E2/E2/E2/E2 VSS SDA SCL WC VCC http://www.wjel.net 22 HUDSON 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 A A B B C C D D E E F F G G H H NC 0.1u C211 NC 0.1u 52 53 U203 NONE OD OD SMT TYPE OPTION(HDCP) 26 15 90 6 115 TO RS232 SMT TYPE 17 NT68665 NT68670 NC R209 0R NC R228 0R 22R NC 1 2 3 5 4 1 2 3 4 5 6 6 NO. PARTS INT_EDID MCU POWER EXT_EDID MCU POWER C212 modify part- 070102 modify parts 1/18 modify parts 1/18 R218 VGA cable detect(high to low) DVI cable detect(high to low) (for flash ) what's the use of 5V_detect here? CN202 G2 C201 F5 C202 F8 C203 B3 C204 B3 C205 B3 C206 C3 C207 C3 C208 C3 C209 D2 C210 D2 C211 D9 C212 D4 C213 E2 C214 E9 C215 E9 C216 E4 C219 E4 C220 E5 C222 F2 D201 B4 FB201 C2 FB202 A2 FB203 B2 FB204 B2 FB205 C2 FB206 D2 FB207 D9 Q201 B4 R201 E5 R202 C3 R205 F8 R206 B4 R207 E9 R209 D9 R210 B6 R211 B6 R213 E2 R214 E4 R215 E3 R218 E5 R219 E9 R220 E9 R221 F6 R223 F3 R224 F3 R225 F5 R228 F8 R229 F3 R230 F3 R231 F2 R232 F3 R233 B4 R234 C4 U201 F2 U203 C5 U204 E2 X201 E5 ZD201 C3 MCU+SCALER TCLK IICSCL 24C16_WP RX VSO VSO HSO IICSDA HSO H_SDA RX TX IRQN IRQN TCLK IICSCL IICSDA 24C16_WP TX H_SCL H_SDA H_SCL 5V_DECT 5V_DECT DDC_WP PANEL_PWR VGA_CABLE RX2+ RXC+ HS RX2- GIN- RX1- RIN- VS DDC_WP RIN+ BIN+ BRIGHTNESS DVI_SCL RX0- KEY_PWR DVI_SDA VGA_SCL RX1+ SOG LED_B/G DVI-HPD KEY1 RX0+ LED_R LF_LED VGA_SDA GIN+ VOLUME KEY2 RXC- PANEL_IDX BIN- DVI_CABLE T7P T6M T6P T7M TCLK2P T0M TCLK1M T4P T1M T2M T5P T3P T5M T2P TCLK2M T4M TCLK1P T1P T0P T3M AUDIO_STDBY LIGHT_SEN BL_CONTROL MCU_VDD CVDD18 CVDD18 MCU_VDD DVDD AVCC +1.8VCC MCU_VDD +1.8VCC +5V PVCC DVDD MCU_VDD MCU_VDD ADC_VAA DVDD +3.3VCC AVCC CVDD18 ADC_VAA DVDD AVCC PVCC CVDD18 DVI_VDD VGA_VDD MCU_VDD MCU_VDD MCU_VDD +5V MCU_VDD CVDD18 R224 NC C206 0.1uF 16V FB204 120 OHM 1 2 R229 NC R225 100R 1/16W C222 NC C209 0.1uF 16V R233 NC R230 NC R202 10K 1/16W C212 NC R223 NC C220 22pF FB203 120 OHM 1 2 U201 NC 4 8 5 6 1 2 3 7 GND VCC SDA SCL A0 A1 A2 WP R215 4K7 1/16W C204 0.1uF 16V R206 4K7 1/16W R220 100R 1/16W FB202 120OHM 1 2 R219 NC C207 0.1uF 16V R228 0R05 1/16W C201 0.1uF 16V C216 0.1uF 16V ZD201 RLZ2.2B R213 4K7 1/16W C211 NC R207 NC C219 22pF R205 NC R214 4K7 1/16W + C214 100uF/16V R201 1M 1/16W U204 M24C16 1 2 3 4 5 6 7 8 NC NC NC VSS SDA SCL WC VCC FB201 NC 1 2 FB205 120 OHM 1 2 R231 NC/4K7 1/16W C208 0.1uF 16V R209 NC C205 0.1uF 16V C213 1uF 16V U203 NT68665MFG-128 39 46 47 50 51 52 53 54 40 48 49 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 6 7 8 9 11 12 69 70 71 72 78 79 111 1 2 3 4 5 10 13 14 16 15 41 42 43 44 45 65 66 67 68 89 90 91 92 101 103 102 104 110 109 108 107 106 105 117 116 115 114 113 112 118 119 120 121 122 124 123 126 125 128 127 55 56 57 58 59 60 61 62 63 64 73 74 75 76 77 80 81 82 84 83 85 86 87 88 94 93 96 95 98 97 100 99 PA6*/PWM8* PB5*/DDC_SDA0 PB4*/DDC_SCL0 SCL/P34 IRQn CVDD DVDD RSBA1P/V0 PA7*/PWM9* RSTn/PD5 SDA/P35 PVCC PGND BIN1+ BIN1- SOG1I GIN1+ GIN1- RIN1+ RIN1- ADC_VAA ADC_GNDA PC2 PD6 PB3/ADC3/INT1 P31/TXD P30/RXD PB2/ADC2/INT0 PB7*/DDC_SDA1 PB6*/DDC_SCL1 PA3/PWM5 PA4*/PWM6* PA5*/PWM7* AVCC RX1+ RX1- AGND RX0- AGND RSGA2M/T7M RSGA3P/TCLK2P RSGA3M/TCLK2M RSRA1P/T6P/RSBB0P DGND/CGND RSBB1P/T3P AD0/GPO2 RSTB MCU_VCC MCU_GND RX2+ RX2- RX0+ RXC+ RXC- REXT AVCC HSYNCI1 TOUTP/VSYNCI1 PLL_GND TCLK PLL_VDD PA0/PWM2 PA2/PWM4 PA1/PWM3 RSGA2P/T7P SP DVDD RSGB2P RSGB2M DGND/CGND PC7 PC6 PD0 GPO1 NC/(HSYNCI) PD4 PD3 PD2 PD1 PWMA/GPO7 GPO6 CVDD INT_HSO/GPO5 INT_VSO/GPO4 AD1/GPO3 PWMB/GPO8 NC/(VSYNCI) PC0* PC1* PC3/PWM0 PC5 PC4/PWM1 PB0/ADC0 PB1/ADC1 OSCO OSCI RSBA1M/V1 RSBA2P/V2 RSBA2M/V3 RSBA3P/V4 RSBA3M/V5 RSCLKAP/V6 RSCLKAM/V7 RSGA1P/VCKI RSGA1M CGND/DGND RSRA1M/T6M/RSBB0M RSRA2P/T5P/RSGB0P RSRA2M/T5M/RSGB0M RSRA3P/T4P/RSRB0P RSRA3M/T4M/RSRB0M RSBB1M/T3M RSBB2P/TCLK1P RSBB2M/TCLK1M RSBB3M/T2M RSBB3P/T2P RSCLKBP/T1P RSCLKBM/T1M RSGB1P/T0P RSGB1M/T0M RSGB3M RSGB3P RSRB1M RSRB1P RSRB2M RSRB2P RSRB3M RSRB3P R221 470R 1/16W FB207 1000OHM 1 2 R210 NC C203 0.1uF 16V CN202 NC 1 2 3 4 R218 22R 1/16W R234 220R 1/16W C210 0.1uF 16V D201 BAV70 Q201 2N3906S-RTK/PS FB206 120OHM 1 2 C215 0.1uF 16V X201 12MHz 1 2 C202 NC R232 NC/0R05 1/16W R211 0R05 1/16W http://www.wjel.net 23 HUDSON 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 A A B B C C D D E E F F G G H H modify 1/8 CN301 D1 C301 B7 C302 A3 C303 A4 C304 B3 C305 B7 C306 B9 C307 B8 C308 B2 C309 E7 C310 E9 C311 E7 C312 E9 C315 D3 C316 E1 C317 D3 D301 E6 FB302 B4 FB303 D2 Q301 B2 Q302 B3 Q305 E4 R301 E4 R302 A4 R303 A4 R304 B1 R305 B2 R307 B2 R308 B2 R309 D1 R311 D4 R312 D5 R314 D3 R316 E4 U301 B8 U302 D8 U303 A8 U304 D8 DC-DC BL_CONTROL BRIGHTNESS PANEL_PWR PANEL_IDX +1.8VCC +3.3VCC +3.3VCC +12V +5V PANEL_VCC +5V +5V +3.3VCC +5V +5V FB303 120� + C306 100uF/16V R308 4K7 1/16W C317 0.1uF 16V + C309 100uF/16V C308 1uF 16V R304 10K 1/16W U303 NC 3 2 1 VI VO GND R311 1K 1/16W C316 0.1uF/25V C304 1uF 16V R316 4K7 1/16W Q305 2N3904S-RTK/PS U302 NC 1 2 3 ADJ/GND OUTPUT INPUT R307 51K� 1/16W C312 0.1uF 16V + C302 10uF/16V CN301 CONN 1 2 3 4 5 6 7 8 9 C307 0.1uF 16V Q302 AO3401 R312 1K 1/16W D301 SM340A R303 330� 1/4W + C310 100uF/16V U304 AP1117E18LA 3 2 1 VI VO GND C311 0.1uF 16V Q301 2N3904S-RTK/PS C303 0.1uF 16V + C305 100uF/16V FB302 120� R305 10K 1/16W R301 1K 1/16W R309 100R 1/16W + C315 100uF/16V R302 330� 1/4W U301 AP1117D33LA 1 2 3 ADJ(GND) VOUT VIN C301 0.1uF 16V R314 4K7 1/16W http://www.wjel.net 24 HUDSON 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 A A B B C C D D E E F F G G H H LVDS OUTPUT OPTION(AUDIO CONTROL) Menu/Up/Down key Auto/Left/Right key modify 1/18 CN401 B4 CN402 A4 CN403 F2 CN404 E6 CN405 F5 CN406 D1 CN407 D4 C401 F8 C402 B7 C403 C7 C404 C7 C405 C2 C406 D8 C407 E8 FB401 F7 FB403 E3 Q402 D8 Q403 E8 Q404 E8 R402 B9 R403 B9 R404 E4 R407 B8 R410 C8 R411 C2 R412 C8 R413 C3 R414 C3 R415 D9 R416 D7 R417 E9 R418 E7 R421 E3 R423 E9 R424 E8 R430 C2 R431 E5 R432 E4 R433 D2 R434 F2 R435 F2 R436 E2 R437 D2 R438 D2 CONNECTOR T3P T0P TCLK1M T4M T1M T4P T7P T5M T6M TCLK1P T7M T1P T3M T2M TCLK2M T0M T6P T2P T5P TCLK2P EAR-L EAR-R LED_O KEY1_PAD KEY2_PAD POWER LED_G LIGHT_SEN OUT-L+ OUT-L- 5V_FB LF_B LED_O KEY1_PAD 5V_FB POWER LED_G KEY2_PAD LF_B LED_G KEY1_PAD LED_O POWER LF_B KEY2_PAD OUT-L+ LED_G LF_B LED_O KEY1_PAD KEY2_PAD POWER EAR-R OUT-R+ OUT-R- EAR-L EAR-SENSE OUT-L- LED_R LED_B/G KEY1 KEY2 KEY_PWR T1P T2M T6P T2P T1M T5M T7P T0M T7M TCLK2P T0P T6M T3M TCLK1M T4M T3P T4P T5P TCLK1P TCLK2M BRIGHTNESS LF_LED VOLUME AUDIO_STDBY LIGHT_SEN +3.3VCC +3.3VCC +3.3VCC +5V PANEL_VCC +3.3VCC +12V +5V +3.3VCC +5V R404 NC R424 NC CN401 NC/CONN 1 2 3 4 5 6 7 8 9 10 11 12 13 FB401 NC 1 2 R407 100R 1/16W R415 10K 1/16W R435 NC C403 0.1uF 16V R436 NC R421 NC/10K 1/16W R413 NC R410 100R 1/16W C407 0.1uF 16V CN407 CONN 1 2 3 4 5 6 7 Q402 2N3906S-RTK/PS R431 NC C402 0.1uF 16V R403 3.9K� 1/16W R430 NC R417 10K 1/16W C401 NC CN403 NC 2 4 6 8 10 12 1 3 5 7 9 11 CN405 NC 1 2 3 4 5 6 7 R438 NC R411 NC R416 100R 1/16W R423 NC R434 NC R433 NC FB403 NC 1 2 C404 0.1uF 16V CN404 NC 1 2 3 4 5 6 7 8 9 R418 100R 1/16W CN406 NC 1 2 3 4 5 6 C405 0.1uF 16V CN402 CONN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Q404 NC R402 3.9K� 1/16W R432 NC/0R05 1/16W C406 0.1uF 16V Q403 2N3906S-RTK/PS R414 NC R412 1K 1/16W R437 NC http://www.wjel.net 25 HUDSON 8 6.2 Power Board 715G2594-1 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 A A B B C C D D E E F F 12V CHANGE 13X20mm F903 JUMPER BD901 A1 CN901 E1 CN902 C8 C900 E4 C901 B2 C902 B2 C903 B2 C904 B8 C907 B2 C909 D1 C910 B4 C911 B3 C912 B2 C913 D3 C914 D2 C915 F4 C916 B2 C920 A6 C921 C6 C922 B6 C923 B6 C924 B7 C925 B7 C926 C6 C927 C8 C928 E6 C929 E7 C930 D9 C931 D8 D900 B4 D901 B4 D910 C3 D911 E4 D915 D6 D916 D6 D920 A6 D921 B5 D922 C6 FB901 C4 FB902 E5 FB903 A2 F901 E2 F902 A9 F903 C9 GND1 E2 GND2 E3 HS1 F2 HS5 F3 IC901 C3 IC902 D5 IC903 E5 L901 C1 L902 B1 L921 A7 L922 B7 NR901 D2 Q900 C4 Q902 B8 Q910 E4 R900 D1 R901 D1 R902 D2 R903 B9 R905 B3 R907 B8 R908 B9 R909 B4 R910 C4 R911 C2 R912 C3 R913 D4 R915 C4 R916 D4 R922 D6 R923 E7 R924 D7 R925 D6 R926 E8 R927 E6 R928 E6 R929 E7 R930 E7 R931 B8 R951 A6 R952 A6 R953 A6 R954 C5 R955 C5 R956 C5 S1 A1 S2 B1 S3 B2 S4 C2 S5 C1 S6 D1 S7 D2 S8 E2 S9 E1 S10 B2 S11 A5 S12 C4 S13 D5 S16 E4 S17 B3 S19 C1 S20 D2 S21 D1 T901 B5 VAR901 B1 ZD901 C3 ZD902 D4 ZD920 B9 ZD921 D6 ZD922 D6 POWER +12V +5V ON/OFF DIM +5V R900 330K 1/4W HS1 HEAT SINK(Q900) 1 2 C931 0.1uF 50V C900 2200PF C902 1000pF R956 47 1/4W � R922 330R 1/8W R915 10K 1/8W L921 3.5uH ! GND1 GND 1 2 R954 47 1/4W � C903 1000PF F902 0R05 1/4W ! - + BD901 KBP208G 2 1 3 4 R909 100K 2W � C904 0.001uF 50V IC902 PC123X2YFZOF 1 2 4 3 ZD902 NC 1 2 R930 1K 1/8W FB901 BEAD 1 2 ZD921 RLZ13B 1 2 Q900 STP10NK70ZFP FB902 Jumper 1 2 ZD922 RLZ5.1B 1 2 ! CN901 SOCKET 1 2 3 D920 SBT150-10LST 1 2 3 D915 LL4148WP CN902 CONNECTOR 1 2 3 4 5 6 7 8 9 10 ! R951 47 1/4W � IC901 LD7575PS 1 2 3 4 5 6 7 8 RT COMP CS GNDOUT VCC NC HV ZD901 NC 1 2 D901 UF4003PT R953 47 1/4W � L901 4.0mH 1 2 4 3 Q902 PMBS3904 C920 0.001uF/500V C930 0.1uF 50V L902 L 1 4 2 3 ! D922 31DQ06FC3 ! + C911 22uF/50V D916 LL4148WP + C922 680uF/25V GND2 GND 1 2 D910 LL4148WP R952 47 1/4W � D911 NC C910 1500PF/2KV + C924 NC D900 BA159GPT ! R901 330K 1/4W ! ! R903 1K 1/8W � C929 0.1uF 50V R924 3K6 1/8W ! C901 1000pF R926 33K 1/8W VAR901 NC ! C912 0.1uF 50V + C907 100uF/450V ! T901 80GL17T-33-N2 4 7 9 5 6 4 6 11 10 8 12 1 3 F901 FUSE R902 330K 1/4W ! NR901 NTCR R910 2.2 1/4W � C916 0.1uF 50V R929 2.4K 1/8W � ZD920 RLZ13B 1 2 Q910 NC + C923 680uF/25V C913 220pF 50V C928 0.1uF 50V C914 470pF/25V ! C915 NC + C925 470uF/25V R931 10K 1/4W � ! R911 100K 1/8W � R925 1K 1/8W ! R916 0.43 2W � + C927 470uF/16V R955 47 1/4W � + C926 1000uF/16V D921 NC 1 2 3 IC903 KIA431A-AT/P R912 10R 1/4W C921 0.001uF/500V L922 3.5uH R913 1K 1/8W ! C909 0.47uF HS5 HEAT SINK(D920) 1 2 R923 10K 1/8W R927 1K 1/8W R928 1K 1/8W R908 470 1/8W FB903 BEAD 1 2 R905 10K 1/4W � R907 150 1W � ! http://www.wjel.net 26 HUDSON 8 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 A A B B C C D D E E F F CHANGE UPDATE CN801 A10 CN802 A10 CN803 D10 CN804 E10 C801 A8 C802 A2 C803 B7 C804 B4 C805 B7 C806 C3 C807 C3 C808 C2 C809 D3 C810 D6 C811 E7 C812 D8 C813 E3 C814 E1 C815 E3 C816 D7 C817 E3 C818 E3 C819 B2 C820 D4 C821 B6 C822 E7 C823 B7 C824 E7 D801 B8 D802 B9 D803 B3 D806 D2 D807 D1 D808 E2 D809 E8 D810 E9 D811 C2 D812 C3 D813 B5 IC801 C4 L801 A9 L802 D9 PT801 A7 PT802 D7 Q801 A3 Q802 A2 Q803 B2 Q804 B6 Q805 C6 Q806 C7 Q807 D4 Q808 D1 Q809 E6 Q810 C6 Q811 C7 Q812 B5 R801 A9 R802 A3 R803 B5 R804 A9 R805 A5 R806 A8 R807 A9 R808 A2 R809 A2 R810 A6 R811 B8 R812 B9 R813 B2 R814 B4 R815 B3 R816 B2 R817 B3 R818 C3 R819 C3 R820 C2 R821 C2 R822 C3 R823 C3 R824 C3 R825 D4 R826 D4 R827 D1 R828 D2 R829 D3 R830 D9 R831 D3 R832 D9 R833 D3 R834 E8 R835 E9 R836 E1 R837 D7 R838 E3 R839 E8 R840 E3 R841 E9 R842 C4 R843 D4 R844 C6 R845 C6 R846 C7 R847 C7 R848 D6 R849 D7 R850 A6 R851 E7 R852 D5 R853 C5 S14 A8 S15 D8 INVERTER OLP1 OLP2 FB FB OLP1 OLP3 OLP4 OLP2 OLP4 FB OLP3 +12V ON/OFF DIM DTC DTC C824 0.1uF/25V PT802 POWER X'FMR 6 3 7 4 8 1 + C805 470uF/25V R813 100 1/10W 5% PT801 POWER X'FMR 6 3 7 4 8 1 R803 2.4K 1/10W � R825 51K 1% 1/8W � R850 15 1/4W � R827 1K 1/10W 1% R838 10K 1/10W 1% C813 0.0022uF D812 LL4148WP C817 0.0022uF D806 BAW56 3 1 2 C B E R823 10K 1/10W Q803 PMBS3904 R829 68K 1% 1/10W � R840 10K 1/10W 1% C801 10pF/3KV R806 1K 1/10W 1% C804 0.1uF/16V D809 BAV99 3 1 2 R817 NC Q809 AM9945N-T1-PF 1 2 3 4 8 7 6 5 S G S G D D D D R839 1K 1/10W 1% C806 1uF/16V CN803 CONN 1 2 L802 NC 1 4 2 3 D811 LL4148WP Q812 RK7002 R807 1K 1/10W 1% R802 100R 1/8W 5% D808 BAW56 3 1 2 C B E C802 1uF 16V R808 10K 1/10W 1% R815 47K 1/10W 1% R844 22R 1/10W 5% R810 15 1/4W � Q805 PMBS3906 C820 NC R822 47K 1/10W 1% R824 10K 1/10W 1% CN801 CONN 1 2 R818 NC D803 LL4148WP R834 1K 1/10W 1% C809 220pF R814 75K 1/10W 1% D801 BAV99 3 1 2 C818 0.0022uF R812 1K 1/10W 1% R847 22R 1/10W 5% R837 15 1/4W � C819 NC + C811 470uF/25V ! Q810 PMBS3904 C816 1500PF/50V R835 1K 1/10W 1% Q811 PMBS3904 ! R830 0R05 1/10W 5% D802 BAV99 3 1 2 Q807 PMBS3904 R846 22R 1/10W 5% R819 10K 1/10W 1% Q804 AM9945N-T1-PF 1 2 3 4 8 7 6 5 S G S G D D D D ZD801 10K 1/4W 5% 1 2 C807 0.1uF/16V L801 NC 1 4 2 3 C822 1500PF/50V R832 0R05 1/10W 5% R804 0R05 1/10W 5% R841 1K 1/10W 1% R821 1M 1/10W 5% R826 180K 1% 1/8W � R816 68K 1% 1/10W � R853 10K 1/10W 1% R828 47K 1/10W 1% IC801 TL494IDR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1IN+ 1IN- FEEDBACK DTC CT RT GND C1 E1 E2 C2 VCC OUTPUT CTRL REF 2IN- 2IN+ CN804 CONN 1 2 D813 LL4148WP R820 560K 1/10W 5% � R842 47K 1/10W 1% C812 10pF/3KV Q808 RK7002 Q801 PDTA144WK R851 15 1/4W � R849 1K 1/10W 1% C808 2.2uF/16V Q802 PDTC144WK R809 NC R852 10K 1/10W 1% D807 LL4148WP D810 BAV99 3 1 2 C821 1500PF/50V C814 0.1uF/16V R811 1K 1/10W 1% Q806 PMBS3906 R831 10K 1/10W 1% R843 NC C823 0.1uF/25V R845 22R 1/10W 5% R801 0R05 1/10W 5% C803 1500PF/50V CN802 CONN 1 2 C810 0.1uF/25V R836 1M 1/10W 5% R833 10K 1/10W 1% C815 0.0022uF R805 4.7K 1/10W 5% R848 1K 1/10W 1% http://www.wjel.net 27 HUDSON 8 6.3 Key Board 715G1755-2 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 A A B B C C D D E E KEY-BRIGHTNESS KEY-MENU/ENTER KEY-SOURCE KEY-SMART IMAGE KEY-VOLUME KEY-AUTO/BACK KEY-LIGHT FRAME KEY-POWER KEY2 add on Mar.-31-07 CN101 B1 C101 B1 C102 B2 C103 B2 C104 B2 C105 B3 LED1 C1 R100 B5 R101 B2 R102 B6 R103 B5 R104 B5 R105 C4 R106 C3 R107 C3 R108 C3 R109 C4 SW1 C6 SW2 C5 SW3 C5 SW4 C4 SW5 C4 SW6 C3 SW7 C3 SW8 C3 LED-O LED-G K-PWR KEY2 K-PWR LED-G LED-O KEY1 KEY1 R103 910� 1/10W SW1 SW 2 1 3 4 5 C103 0.01uF R108 2.4K� 1/10W R109 0R05 1/10W 5% C104 0.01uF SW8 SW 2 1 3 4 5 LED1 LED 1 3 2 R100 0R05 1/8W C102 0.01uF C101 0.01uF C105 0.01uF R106 4K3 1/10W R101 100R 1/10W 5% R107 910� 1/10W R102 4K3 1/10W SW5 SW 2 1 3 4 5 SW4 SW 2 1 3 4 5 R104 2.4K� 1/10W SW3 SW 2 1 3 4 5 SW6 SW 2 1 3 4 5 SW2 SW 2 1 3 4 5 R105 NC CN101 CONN 1 2 3 4 5 6 SW7 SW 2 1 3 4 5 http://www.wjel.net 28 HUDSON 8 7. PCB Layout 7.1 Main Board 715G2561-1 C101 B3 C215 B3 D105 C1 Q301 A3 R144 C2 R410 B1 C102 C1 C216 A1 D106 C2 Q302 A3 R201 B2 R411 A3 C103 C1 C219 B2 D107 C2 Q305 A1 R202 A2 R412 B1 C104 B1 C220 B2 D108 C2 Q402 B2 R205 A1 R413 A3 C105 C2 C222 B3 D109 C2 Q403 B2 R206 B3 R414 A3 C106 C2 C301 B2 D110 B3 Q404 B1 R207 B3 R415 B2 C107 C2 C302 A3 D111 C3 R101 C3 R209 B3 R416 B2 C110 B1 C303 A3 D112 C3 R102 C1 R210 A2 R417 B2 C111 B2 C304 A3 D113 C2 R103 C2 R211 A2 R418 B1 C112 B2 C305 B2 D201 B3 R104 C2 R213 B3 R421 B2 C113 C2 C306 B1 D301 A2 R105 C2 R214 B2 R423 B1 C114 B2 C307 B1 FB101 C2 R106 C1 R215 B3 R424 B1 C115 C3 C308 A3 FB102 B3 R107 C1 R218 B2 R430 A3 C116 C3 C309 A2 FB103 C3 R108 C2 R219 B3 R431 B1 C117 C3 C310 A2 FB104 C3 R109 B2 R220 A1 R432 A1 C118 C2 C311 A2 FB105 C3 R110 B1 R221 B2 R433 A1 C121 B3 C312 A2 FB106 C2 R111 B1 R223 B3 R434 B1 C122 B3 C315 A1 FB107 C1 R113 C2 R224 A3 R435 B1 C123 B2 C316 A1 FB201 B3 R115 C2 R225 B2 R436 B1 C124 B3 C317 A1 FB202 B3 R116 C2 R228 B3 R437 A1 C125 B3 C401 B1 FB203 B3 R117 B2 R229 B3 R438 A1 C126 B2 C402 B1 FB204 B2 R118 B2 R230 B3 R439 B1 C127 B3 C403 B1 FB205 B2 R120 B2 R231 B3 U101 B2 C128 C3 C404 B1 FB206 B2 R122 C2 R232 B3 U102 B3 C129 B2 C405 A3 FB207 B3 R123 B3 R233 B3 U201 B3 C130 C2 C406 B2 FB302 A3 R124 B3 R234 B2 U203 B2 C131 C1 C407 B1 FB303 A1 R125 B3 R301 A1 U204 B3 C132 C1 CN101 C3 FB401 B1 R126 C3 R302 A3 U301 B1 C201 B2 CN102 C2 FB403 A1 R127 C3 R303 A3 U302 A2 C202 A1 CN202 B3 FDT1 B3 R128 C3 R304 A3 U303 B1 C203 B2 CN301 A2 FDT10 <1 R129 C3 R305 A3 U304 A2 C204 B3 CN401 B1 FDT11 C8 R131 C2 R307 A3 X201 B2 C205 B3 CN402 A2 FDT12 <8 R132 C3 R308 A3 ZD101 C3 C206 B2 CN403 B1 FDT13 C1 R133 C3 R309 A1 ZD102 B1 C207 B2 CN404 B1 FDT2 A2 R134 C3 R311 A1 ZD103 B2 C208 B2 CN405 B1 FDT3 A3 R135 C2 R312 A1 ZD104 B2 C209 B3 CN406 A1 FDT4 C1 R136 C3 R314 A1 ZD105 C3 C210 B2 CN407 B1 FDT5 C1 R138 C2 R316 A1 ZD106 C3 C211 A2 D101 C1 FDT6 <1 R139 C3 R402 B1 ZD107 C3 C212 B2 D102 C2 FDT7 C8 R140 C2 R403 B1 ZD201 B2 C213 B3 D103 C1 FDT8 <8 R141 C3 R404 A1 C214 B3 D104 C1 Q201 B3 R142 C3 R407 B1 http://www.wjel.net 29 HUDSON 8 29 HUDSON 8 http://www.wjel.net 30 HUDSON 8 7.2 Power Board 715G2594-1 BD901 D4 J802 C2 C801 A1 J803 B1 C805 B2 J804 B1 C811 C2 J805 B2 C812 D1 J806 B1 C900 B4 J808 C2 C901 D3 J809 C2 C902 D3 J810 C2 C903 D4 J811 C2 C907 C4 J812 B2 C909 D3 J817 C2 C910 C4 J819 B2 C911 C3 J901 D3 C920 B3 J903 C3 C921 B4 J904 A3 C922 B3 J905 A3 C923 B3 J906 A4 C924 B3 J909 A2 C925 A3 J910 A2 C926 B3 L801 B1 C927 A4 L802 C1 C932 B4 L901 D3 CN801 A1 L902 D4 CN802 A1 L921 A3 CN803 D1 L922 A4 CN804 D1 NR901 C2 CN901 D2 PT801 B1 CN902 A4 PT802 C2 D804 B1 Q900 C4 D805 B1 R907 A3 D814 C1 R909 C3 D815 C2 R916 C4 D900 C3 SG11 C4 D901 C3 SG12 D2 D920 A3 SG19 D2 D921 B4 SG22 D4 D922 A4 SG25 D4 F901 D2 SG27 D3 F903 A4 SG28 C3 FB901 C4 SG31 D3 FB902 B4 SG33 A1 FB903 C4 SG34 A1 HS10 A3 SG35 A1 HS13 A3 SG36 A1 HS14 A2 SG39 A1 HS16 A2 SG40 D1 HS17 B4 SG42 D1 HS20 A8 SG44 D1 HS28 A7 SG45 D1 HS29 B1 SG46 C4 HS31 B4 SG47 C4 IC902 B3 SG49 C4 IC903 B3 T901 C3 J801 B2 VAR901 D3 http://www.wjel.net 31 HUDSON 8 31 HUDSON 8 C802 A2 J907 C3 R843 B2 C803 B1 J908 C3 R844 B2 C804 B2 Q801 A2 R845 B1 C806 B2 Q802 A2 R846 B1 C807 C2 Q803 A2 R847 C2 C808 B2 Q804 B1 R848 B2 C809 C2 Q805 B1 R849 B2 C810 A2 Q806 B1 R850 B2 C813 B1 Q807 B2 R851 C2 C814 B2 Q808 B2 R852 B2 C815 B1 Q809 C1 R853 B2 C816 C1 Q810 C2 R900 D3 C817 C1 Q811 B1 R901 D3 C818 C1 Q812 A2 R902 C2 C819 A2 Q902 A3 R903 A3 C820 B2 Q910 C3 R905 C3 C821 B2 R801 B1 R908 A3 C822 C2 R802 B2 R910 C3 C823 B2 R803 A2 R911 C3 C824 C2 R804 B1 R912 C3 C904 A3 R805 B2 R913 C3 C912 C3 R806 B1 R915 C3 C913 C3 R807 B1 R922 A3 C914 C3 R808 A2 R923 A2 C915 C3 R809 A2 R924 A2 C916 C3 R810 B1 R925 B3 C928 B3 R811 B1 R926 A3 C929 B2 R812 B1 R927 B2 C930 A4 R813 A2 R928 B3 C931 A4 R814 C2 R929 B2 D801 B1 R815 B2 R930 B2 D802 B1 R816 B2 R931 A3 D803 A2 R817 B2 R951 B3 D806 B1 R818 B2 R952 B3 D807 B2 R819 B2 R953 B3 D808 C1 R820 B2 R954 B4 D809 C1 R821 B2 R955 B4 D810 C1 R822 C2 R956 B4 D811 B2 R823 B2 SG10 C3 D812 B2 R824 C2 SG15 D3 D813 B2 R825 B2 SG17 D3 D910 C3 R826 B2 SG18 D4 D911 C3 R827 B2 SG20 D4 D915 A2 R828 B2 SG21 D3 D916 A2 R829 B2 SG23 D4 F902 A3 R830 C1 SG24 D3 HS11 D4 R831 B1 SG26 D4 HS15 A1 R832 C1 SG29 C3 HS21 A7 R833 B1 SG30 D3 HS22 A1 R834 C1 SG32 D3 IC801 B2 R835 C1 SG37 D2 IC901 C3 R836 B2 SG38 D2 J807 C2 R837 C2 ZD801 A2 J813 C1 R838 C1 ZD901 C3 J814 C1 R839 C1 ZD902 C4 J815 C1 R840 C1 ZD920 A3 J816 B2 R841 C1 ZD921 A2 J818 A2 R842 C2 ZD922 A2 http://www.wjel.net 32 HUDSON 8 7.3 Key Board 715G1755-2 CN101 A1 LED1 A4 SW1 A5 SW2 A5 SW3 A5 SW4 A4 SW5 A4 SW6 A3 SW7 A3 SW8 A3 GND A2 C101 A1 C102 A1 C103 A4 C104 A4 C105 A5 R100 A4 R101 A4 R102 A5 R103 A5 R104 A4 R105 A4 R106 A3 R107 A3 R108 A2 R109 A4 http://www.wjel.net 33 HUDSON 8 8. Wiring Diagram Panel Power Board Main Board Key Board CN301 CN402 CN101 CN407 CN102 CN101 DVI D-SUB AC-IN CN901 CN801 CN802 CN804 CN803 CN902 Lamp Wire Harness Lamp Wire Harness Power Wire Harness Key Board Wire FFC Panel Interface CN402 http://www.wjel.net 34 HUDSON 8 9. Mechanical Instructions 1. Back View as Fig1 Place the monitor face down on a smooth surface as Fig 1. Be careful to avoid scratch and injury during the uninstallation. Fig1 2. Remove the cable management as Fig2. Fig2 http://www.wjel.net 35 HUDSON 8 3. Remove the base as Fig3~Fig4. Fig3 Fig4 http://www.wjel.net 36 HUDSON 8 4. Remove the stand as Fig5 and Fig6. Remove the four screws to remove the stand. Fig5 Fig6 http://www.wjel.net 37 HUDSON 8 5. Remove the hinge cover as Fig7~ Fig8. Fig7 Fig8 http://www.wjel.net 38 HUDSON 8 5. Remove the hinge as Fig9. Remove the four screws to remove the hinge as Fig9. Fig9 6. Remove rear cover as Fig10. a. Remove 3 screws to remove rear cover as Fig10. Fig10 http://www.wjel.net 39 HUDSON 8 b. Insert plastic putty knife into the gap between front bezel and back cover to release 3 snaps on the left, 3 snaps on the right and 5 snaps on the top as Fig11 - Fig14 Fig11 Fig13 Fig13 Insert plastic putty knife into the gap between front bezel and back cover Front Bezel Back cover 4 snaps on the left 4 snaps on the right http://www.wjel.net 40 HUDSON 8 Fig14 7. Remove shielding as Fig15. Remove 9 screws to remove shielding as Fig15. Fig15 5 snaps on the top http://www.wjel.net 41 HUDSON 8 8. Remove main board and power board as Fig16. Remove 8 screws to remove main board and power board as Fig16. Fig16 9. Remove the bezel as Fig17- Fig19 a. Remove 3 screws at the bottom of the main frame as Fig17. b. Remove 3 screws at the left of bezel as Fig18. c. Remove 3 screws at the right of bezel as Fig19. Fig17 http://www.wjel.net 42 HUDSON 8 Fig18 Fig19 10. Remove the main frame as Fig20- Fig21. a. Remove 2 screws at the right of main frame Fig20. b. Remove 2 screws at the left and 1screw at the bottom of the main frame Fig21. Fig20 http://www.wjel.net 43 HUDSON 8 Fig21 11. The end as Fig22. Fig22 http://www.wjel.net 44 HUDSON 8 10. Trouble Shooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative. http://www.wjel.net 45 HUDSON 8 http://www.wjel.net 46 HUDSON 8 11. Repair Flow Chart 11.1 Main Board (1). No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the Adapter/Inverter section X201 oscillate waveforms are normal Replace D301, U301 or U304 Replace U203 Replace X201 OK OK OK NG NG NG NG Measure U301 PIN2=3.3V Measure U304 PIN2=1.8V http://www.wjel.net 47 HUDSON 8 (2). No Picture No picture OK OK NG NG Replace D301, U301 or U304 X201 oscillate waveforms are normal Replace X201 Check if the sync signal from computer is output and video cable is connected normally Input the sync signal of computer, or change the cable Replace U203 NG OK Measure U301 PIN2=3.3V Measure U304 PIN2=1.8V http://www.wjel.net 48 HUDSON 8 (3). White screen White screen Check Q301, Q302 is broken or CN402 solder? Check Correspondent component. Replace Panel Check Correspondent component. Replace U203 OK OK Replace X201 OK NG NG NG NG Check reset circuit of U203 is normal OK X201 oscillate waveform is normal Measure Q301 base is high level? http://www.wjel.net 49 HUDSON 8 11.2. Power/Inverter Board (1) No power Check CN902 pin4, 5 = 12V Check AC line volt 110V or 220V Check AC input Check the voltage of C907 (+) Check bridge rectified circuit and F901 circuit Check start voltage for the pin8 of IC901 Check R905 and Change IC901 NG Check the auxiliary voltage is bigger than 10V and smaller than 20V 1) Check IC901 2) Check R910, D901 circuit OK OK NG Check D910, Q900, D900, IC902, F902, ZD921, ZD922, D915, D916 OK Check IC901 pin5 PWM wave OK Check IC901 NG NG NG OK NG http://www.wjel.net 50 HUDSON 8 (2) W / LED, No Backlight Check CN902 pin4, 5 = 12V NG OK Check adapter or MB Check ON/OFF signal Check Interface board NG OK Check IC801 PIN12=12V NG OK Change Q801 Check IC801 PIN10, 9 have the output of square wave at short time NG OK Change IC801 Check Q804, Q809 PIN5, 6, 7, 8 have the output of square wave at short time. NG OK Check Q804, Q805, Q806, Q809, Q810, Q811 Check the output of PT801, PT802 Check connecter & lamp OK NG Change PT801, PT802 http://www.wjel.net 51 HUDSON 8 11.3 Key Board OSD is unstable or not working Is Key Pad Board connecting normally? Connect Key Pad Board Is Button Switch normally? Replace Button Switch Y N N Is Key Pad Board normally? Replace Key Pad Board Y N Y Check Main Board http://www.wjel.net 52 HUDSON 8 12. ISP Instruction (1). Install the program software a. First decompressing files , as follow: http://www.wjel.net 53 HUDSON 8 b. Double – click , start to install as follows: http://www.wjel.net 54 HUDSON 8 http://www.wjel.net 55 HUDSON 8 http://www.wjel.net 56 HUDSON 8 c. There will be a shortcut key appears on the desktop. (2). Connect the ISP board as follow: a. Double-click ，running the program as follows: Connect to the PC LPT Connect to the Philips 190S8 http://www.wjel.net 57 HUDSON 8 b. Click icon, search the program” PHILIPS_190S_HSD_HSD190MEN3_V0.29.hex”, and click open: http://www.wjel.net 58 HUDSON 8 c. Click icon, the writer is in processing… d. Until appears the follow Fig, writer completed. http://www.wjel.net 59 HUDSON 8 13. DDC Instruction General DDC Data Re-programming In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect, repaired monitor’ the serial numbers have to be re-programmed. It is advised to re- soldered the main EEPROM with Software DDC from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed. Additional information about DDC (Display Data Channel) may be obtained from Video Electronics Standards Association (VESA). Extended Display Identification Data (EDID) information may be also obtained from VESA. 1. An i486 (or above) personal computer or compatible. 2. Microsoft operation system Windows 95/98/2000/XP. 3. “ PORT95NT.exe, WinDDC_ setup” program. 4. Software OSD SN Alignment kits The kit contents: a. OSD SN BOARD x1 b. Printer cablex1 c. VGA cable x1 d. Digital cable x1 e. 12V DC power source 1. Install the “PORT95NT.EXE”, and restart the computer. You must install the at the first. The processing as follows: http://www.wjel.net 60 HUDSON 8 http://www.wjel.net 61 HUDSON 8 http://www.wjel.net 62 HUDSON 8 http://www.wjel.net 63 HUDSON 8 Click to complete the installation. Note: After installation, you must restart the PC to take the setup to effect. http://www.wjel.net 64 HUDSON 8 2. Install the “WinDDC_ setup” Second, you must install the . The processing as follows: http://www.wjel.net 65 HUDSON 8 http://www.wjel.net 66 HUDSON 8 Click to complete the installation. 3. Connect the DDC board as follow: Connect to the PC LPT When you write analog EDID, Connect this port to the Philips 190S8’s VGA port 12V Input When you write digital EDID, Connect this port to the Philips 190S8’s DVI port http://www.wjel.net 67 HUDSON 8 4. Take analog DDC write for example, as follow a. Double-click ，appear as follow Figs： http://www.wjel.net 68 HUDSON 8 b. Click . c. Key 14 numbers in the Serial Number blank, then click “OK”. Now analog DDC Write completes, as follow. Note: The way of digital DDC write is the same as analog DDC write. http://www.wjel.net 69 HUDSON 8 190S8 EDID Analog 128 bytes EDID Data (Hex): 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 0: 00 FF FF FF FF FF FF 00 41 0C 59 08 01 01 01 01 16: 0C 0D 01 03 0E 26 1E 78 EE A1 50 A3 57 4C 9D 25 32: 11 50 54 BF EF 80 71 4F 81 40 81 80 01 01 01 01 48: 01 01 01 01 01 01 30 2A 00 98 51 00 2A 40 30 70 64: 13 00 78 2D 11 00 00 1E 00 00 00 FF 00 32 31 33 80: 32 33 31 32 33 32 31 33 32 33 00 00 00 FC 00 50 96: 68 69 6C 69 70 73 20 31 39 30 53 0A 00 00 00 FD 112: 00 38 4C 1E 53 0E 00 0A 20 20 20 20 20 20 00 A2 Decoded EDID data <---Header---> Header: 00 FF FF FF FF FF FF 00 <-x-Header-x-> <---Vendor/Product Identification---> ID Manufacturer Name: PHL ID Product Code: 0859 ID Serial Number: 01010101 Week of Manufacture: 12 Year of Manufacture: 2003 <-x-Vendor/Product Identification-x-> <---EDID Structure Version/Revision---> EDID Version#: 01 EDID Revision#: 03 <-x-EDID Structure Version/Revision-x-> <---Basic Display Parameters/Features---> Video i/p definition: Analog Signal Level Standard: 0.700V/0.300V(0.700Vpp) Setup: Blank-to-Black not expected Separate Sync Support: Yes Composite Sync Support: Yes Sync. on green video supported:Yes Serration of the Vsync.Pulse is not required. Max. H. Image Size : 38cm. Max. V. Image Size : 30cm. Display Gamma: 2.2 DPMS Features, Stand-by: Yes. DPMS Features, Suspend: Yes. DPMS Features, Active off: Yes. Display Type: R/G/B color display. Standard Default Color Space: Yes. Preferred Timing Mode: Yes. <---Basic Display Parameters/Features---> <---Color Characteristics---> Red x: 0.6386718750 Red y: 0.3417968750 Green x: 0.2968750000 Green y: 0.6142578125 Blue x: 0.1455078125 Blue y: 0.0673828125 White x: 0.3125000000 http://www.wjel.net 70 HUDSON 8 White y: 0.3291015625 <-x-Color Characteristics-x-> <---Established Timings---> Established Timings 1: BF -720x400 @70Hz VGA,IBM -640x480 @60Hz VGA,IBM -640x480 @67Hz Apple,Mac II -640x480 @72Hz VESA -640x480 @75Hz VESA -800x600 @56Hz VESA -800x600 @60Hz VESA Established Timings 2: EF -800x600 @72Hz VESA -800x600 @75Hz VESA -832x624 @75Hz Apple,Mac II -1024x768 @60Hz VESA -1024x768 @70Hz VESA -1024x768 @75Hz VESA -1280x1024 @75Hz VESA Established Timings 3: 80 -1152x870 @75Hz Apple,Mac II <-x-Established Timings-x-> <---Standard Timing Identification---> -1152x864 @75 -1280x960 @60 -1280x1024 @60 <-x-Standard Timing Identification-x-> <---Detailed Timing Descriptions---> Detailed Timing: 1280x1024 @ 60Hz. <-x-Detailed Timing Descriptions-x-> <---Detailed Timing Descriptions---> Detailed Timing: FF (Monitor SN) '213231232132' Detailed Timing: FC (Monitor Name) 'Philips 190S' Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30KHz Max. H. rate: 83KHz Max. Pixel Clock: 140MHz <-x-Detailed Timing Descriptions-x-> Extension Flag: 00 Checksum: A2 http://www.wjel.net 71 HUDSON 8 190S8 EDID Digital 128 bytes EDID Data (Hex): 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 0: 00 FF FF FF FF FF FF 00 41 0C 59 08 01 01 01 01 16: 15 0D 01 03 80 26 1E 78 EE A1 50 A3 57 4C 9D 25 32: 11 50 54 BF EF 80 71 4F 81 40 81 80 01 01 01 01 48: 01 01 01 01 01 01 30 2A 00 98 51 00 2A 40 30 70 64: 13 00 78 2D 11 00 00 1E 00 00 00 FF 00 31 33 32 80: 32 33 32 31 33 31 32 33 33 32 00 00 00 FC 00 50 96: 68 69 6C 69 70 73 20 31 39 30 53 0A 00 00 00 FD 112: 00 38 4C 1E 53 0E 00 0A 20 20 20 20 20 20 00 27 Decoded EDID data <---Header---> Header: 00 FF FF FF FF FF FF 00 <-x-Header-x-> <---Vendor/Product Identification---> ID Manufacturer Name: PHL ID Product Code: 0859 ID Serial Number: 01010101 Week of Manufacture: 21 Year of Manufacture: 2003 <-x-Vendor/Product Identification-x-> <---EDID Structure Version/Revision---> EDID Version#: 01 EDID Revision#: 03 <-x-EDID Structure Version/Revision-x-> <---Basic Display Parameters/Features---> Video i/p definition: Digital Max. H. Image Size : 38cm. Max. V. Image Size : 30cm. Display Gamma: 2.2 DPMS Features, Stand-by: Yes. DPMS Features, Suspend: Yes. DPMS Features, Active off: Yes. Display Type: R/G/B color display. Standard Default Color Space: Yes. Preferred Timing Mode: Yes. <---Basic Display Parameters/Features---> <---Color Characteristics---> Red x: 0.6386718750 Red y: 0.3417968750 Green x: 0.2968750000 Green y: 0.6142578125 Blue x: 0.1455078125 Blue y: 0.0673828125 White x: 0.3125000000 White y: 0.3291015625 <-x-Color Characteristics-x-> <---Established Timings---> Established Timings 1: BF -720x400 @70Hz VGA,IBM http://www.wjel.net 72 HUDSON 8 -640x480 @60Hz VGA,IBM -640x480 @67Hz Apple,Mac II -640x480 @72Hz VESA -640x480 @75Hz VESA -800x600 @56Hz VESA -800x600 @60Hz VESA Established Timings 2: EF -800x600 @72Hz VESA -800x600 @75Hz VESA -832x624 @75Hz Apple,Mac II -1024x768 @60Hz VESA -1024x768 @70Hz VESA -1024x768 @75Hz VESA -1280x1024 @75Hz VESA Established Timings 3: 80 -1152x870 @75Hz Apple,Mac II <-x-Established Timings-x-> <---Standard Timing Identification---> -1152x864 @75 -1280x960 @60 -1280x1024 @60 <-x-Standard Timing Identification-x-> <---Detailed Timing Descriptions---> Detailed Timing: 1280x1024 @ 60Hz. <-x-Detailed Timing Descriptions-x-> <---Detailed Timing Descriptions---> Detailed Timing: FF (Monitor SN) '132232131233' Detailed Timing: FC (Monitor Name) 'Philips 190S' Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30KHz Max. H. rate: 83KHz Max. Pixel Clock: 140MHz <-x-Detailed Timing Descriptions-x-> Extension Flag: 00 Checksum: 27 http://www.wjel.net 73 HUDSON 8 14. White Balance, Luminance Adjustment 1. Apparatuses and program: analyzer CA-210, PC, tool, FGA adjustment program (FGAWB0.15SN), Pattern generator. 2. Equipment installation: a. Connect analyzer CA-210 to PC by USB connector, install drive program CA-SDK Ver4.00 for CA-210 and restart PC after finish installing. b. Install Port95NT drive program, set PC printer connector mode as ECP mode and restart PC after finish installing. c. Connect tools as follow: (Note: It is not necessary to connect Port2 ) 3. Adjustment Preparation before adjustment: (1) Monitor should be warmed up for more than half an hour. (2) Make sure that the tools are connected right and drive programs have been installed OK. Adjustment process: (1) Press the power of CA-210, shut off the lens, press 0-Cal and open the lens after analyzer reset. (2) Start white balance adjustment program, select the right parameter according with the program and click OK. (3) Make sure that the lens of CA-210 aims at the center of the screen, then click Start and start adjusting. (4) After finish adjusting, the adjustment program displays pass, and the Start Button is changed to Next, which means you can adjust another monitor. http://www.wjel.net 74 HUDSON 8 4. Color Temp confirmation Connect the signal to the monitor, the monitor display white-picture, use CA-210 to measure the Color Temp of the screen center and select the OSD to make sure whether the Color Temps accord with the SPEC. http://www.wjel.net 75 HUDSON 8 15. Monitor Exploded View http://www.wjel.net 76 HUDSON 8 16. Recommended & Spare Parts List Recommended Parts List 190S8FS/00 Item Location Part No. Description Philips 12NC Remark 1 FQ003 P34G1829 VOD1T BEZEL L19-7phb1-S3 2 FQ004 P34G1830 VB 1T REAR COVER 3 FQ002 P33G4975 VPB1C BUTTON_OSD 4 FQ001 705GQ734241 STAND/BASE ASS'Y 190S_VB 5 FQ016 A34G0449 VB 1B0133 BASE 6 FQ017 A37G0042 1 HINGE 7 FQ018 A34G0414 VB 1B0100 STAND 8 FQ019 A33G0235 VB 1X0100 CABLE MANAGEMENT 9 E750L 750GLG90E8L12M000F PANEL LM190E08-TLL1 NJ PHP LPL 9 E750L 750GLH90N3A12M000F PANEL HSD190MEN3-A00 NJ HSD 9 E750L 750GLG190E8G23M0PH PANEL LM190E08-TLG2 GZ LPL Second source 9 E750L 750GLG90E8L42M000F PANEL LM190E08-TLL4 NJ LPL Second source 9 E750L 750GLG190E8G43M0PH PANEL LM190E08-TLG4 GZ LPL Second source 9 E750 750GLG190E8G23M0PH PANEL LM190E08-TLG2 GZ LPL 10 FQ012 CBPC7HNAPHQA3 SCALER BOARD ASSY(HSD) 10 FQ013 CBPC7GNAPHQA9 SCALER BOARD ASSY (LG) 10 FQ013 CBPC7GNAPHQ2 SCALER BOARD ASSY (LPL) 11 FQ015 PWPC7942GQA8 POWER BOARD ASSY E089A 089G 728HAA 21 SIGNAL CABLE E089C 089G179E30H712 FFC CABLE E089C 089G179J30H712 FFC E08907 089G179E30H579 FFC CABLE E089B 089G404A18N YH POWER CABLE E08901 089G404A18N IS POWER CORD E095A 095G8014 7D514 WIRE HARNESS http://www.wjel.net 77 HUDSON 8 E09502 095G8014 7X514 WIRE HARNESS FQ005 P45G 88609 37 R EPE BAG FQ006 Q40G 19N81319A RATING LABEL FQ007 Q44G9071 1 CUSHION-RIGHT FQ008 Q44G9071 2 CUSHION-LEFT FQ020 705GQ8CS008 CUSHION ASSY FQ009 Q44G9071 3 EPS FQ010 Q44G9071813 3A 19 LCD CARTON FQ011 Q70G9000813 9A CD MANUAL FQ014 KEPC7QS5 KEY BOARD ASSY U301 056G 563 52 IC AP1117D33LA TO252-3L ATC U304 056G 56327A IC AP1117E18LA SOT223-3L U204 056G1133 56 M24C16-WMN6TP U204 056G1133 24 1 2nd SOURCE AT24C16B U203 705GQ756019 MCU ASS'Y （LG） U203 705GQ756020 MCU ASS'Y （HSD） U203 705GQ756099 MCU ASS'Y (LPL) U811 056G 608 10 IC OZ9938GN-B SOIC-16 IC902 056G 139 3A IC PC123Y22FZ0F IC902 056G 139 3B IC PC123Y82FZ0F IC902 056G 139 5A TCET1103G IC941 056G 158 4 T H431BA IC941 056G 158 10 T IC AZ431AZ-AE1 TO-92 BY AAC IC901 056G 564911 IC TEA1532AT S08 http://www.wjel.net 78 HUDSON 8 Spare Parts List Service Kit Description Part No. Philips 12NC Remark DDC Kit 715L2005C2 9965 000 43197 for all model OSD SN Kit 715GT033 C 9965 000 43252 for all model for all hudson 7 NOVATEK ISP Kit 715LT035A 9965 000 43198 for 170A8, 190B8, 150S8, 170S8,190S8, 170V8,190V8 MSTAR ISP Kit 715GT039 A 996510010027 200CW8 REALTEK ISP Kit 715GT039 A 996510010027 170CW8 190S8FS/00 Panel Location Part No. Description Philips 12NC Remark E750L 750GLG90E8L12M000F PANEL LM190E08-TLL1 NJ PHP LPL E750L 750GLH90N3A12M000F PANEL HSD190MEN3-A00 NJ HSD E750L 750GLG190E8G23M0PH PANEL LM190E08-TLG2 GZ LPL Second source E750L 750GLG90E8L42M000F PANEL LM190E08-TLL4 NJ LPL Second source E750L 750GLG190E8G43M0PH PANEL LM190E08-TLG4 GZ LPL Second source E750 750GLG190E8G23M0PH PANEL LM190E08-TLG2 GZ LPL Board ASS’Y Location Part No. Description Philips 12NC FQ012 CBPC7HNAPHQA3 SCALER BOARD ASSY (HSD) FQ013 CBPC7GNAPHQA9 SCALER BOARD ASSY (LG) FQ013 CBPC7GNAPHQ2 SCALER BOARD ASSY (LPL) FQ015 PWPC7942GQA8 POWER BOARD ASSY FQ014 KEPC7QS5 KEY BOARD ASSY http://www.wjel.net 79 HUDSON 8 Accessory and Mechanical Location Part No. Description Philips 12NC Remark E089A 089G 728HAA 21 SIGNAL CABLE E089C 089G179E30H712 FFC CABLE E089C 089G179J30H712 FFC E08907 089G179E30H579 FFC CABLE E089B 089G404A18N YH POWER CABLE E08901 089G404A18N IS POWER CORD E095A 095G8014 7D514 WIRE HARNESS E09502 095G8014 7X514 WIRE HARNESS FQ001 705GQ734241 STAND/BASE ASS'Y 190S_VB E750L 750GLG90E8L12M000F PANEL LM190E08-TLL1 NJ PHP LPL E750L 750GLH90N3A12M000F PANEL HSD190MEN3-A00 NJ HSD E750L 750GLG190E8G23M0PH PANEL LM190E08-TLG2 GZ LPL Second source E750L 750GLG90E8L42M000F PANEL LM190E08-TLL4 NJ LPL Second source E750L 750GLG190E8G43M0PH PANEL LM190E08-TLG4 GZ LPL Second source E750 750GLG190E8G23M0PH PANEL LM190E08-TLG2 GZ LPL FQ002 P33G4975 VPB1C BUTTON_OSD FQ003 P34G1829 VOD1T BEZEL L19-7PHB1-S3 FQ004 P34G1830 VB 1T REAR COVER FQ005 P45G 88609 37 R EPE BAG FQ006 Q40G 19N81319A RATING LABEL FQ007 Q44G9071 1 CUSHION-RIGHT FQ008 Q44G9071 2 CUSHION-LEFT FQ020 705GQ8CS008 CUSHION ASSY FQ009 Q44G9071 3 EPS FQ010 Q44G9071813 3A 19 LCD CARTON FQ011 Q70G9000813 9A CD MANUAL http://www.wjel.net 80 HUDSON 8 Board Parts Location Part No. Description Philips 12NC FQ012 CBPC7HNAPHQA3 SCALER BOARD ASSY (HSD) FQ013 CBPC7GNAPHQA9 SCALER BOARD ASSY (LG) FQ013 CBPC7GNAPHQ2 SCALER BOARD ASSY (LPL) C302 067G305V100 3 105℃ 10UF +-20% 16V C315 067G305V101 3 105℃ 100UF M 16V C310 067G305V101 3 105℃ 100UF M 16V C309 067G305V101 3 105℃ 100UF M 16V C306 067G305V101 3 105℃ 100UF M 16V C305 067G305V101 3 105℃ 100UF M 16V C214 067G305V101 3 105℃ 100UF M 16V CN101 088G 35315F H D-SUB 15PIN CN102 088G 35424F N DVI 24PIN CONN F X201 093G 22 51 CRYSTAL 12MHz HC-49US ARG6-120 U301 056G 563 52 IC AP1117D33LA TO252-3L ATC U304 056G 56327A IC AP1117E18LA SOT223-3L U204 056G1133 56 M24C16-WMN6TP U204 056G1133 24 1 2nd SOURCE AT24C16B Q301 057G 417 12 T KEC 2N3904S-RTK/PS Q305 057G 417 12 T KEC 2N3904S-RTK/PS Q403 057G 417 13 T KEC 2N3906S-RTK/PS Q402 057G 417 13 T KEC 2N3906S-RTK/PS Q201 057G 417 13 T KEC 2N3906S-RTK/PS Q302 057G 763 1 A03401 SOT23 BY AOS(A1) R211 061G0402000 RST CHIPR 0 OHM +-5% 1/16W R228 061G0402000 RST CHIPR 0 OHM +-5% 1/16W R118 061G0402100 RST CHIPR 10 OHM +-5% 1/16W R117 061G0402100 RST CHIPR 10 OHM +-5% 1/16W R116 061G0402100 RST CHIPR 10 OHM +-5% 1/16W R115 061G0402100 RST CHIPR 10 OHM +-5% 1/16W R111 061G0402100 RST CHIPR 10 OHM +-5% 1/16W R110 061G0402100 RST CHIPR 10 OHM +-5% 1/16W R107 061G0402100 RST CHIPR 10 OHM +-5% 1/16W R106 061G0402100 RST CHIPR 10 OHM +-5% 1/16W R136 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R220 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R225 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R309 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R407 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R410 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R416 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R418 061G0402101 RST CHIPR 100 OHM +-5% 1/16W http://www.wjel.net 81 HUDSON 8 R108 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R109 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R126 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R127 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R128 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R132 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R134 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R135 061G0402101 RST CHIPR 100 OHM +-5% 1/16W R412 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W R312 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W R311 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W R301 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W R144 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W R122 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W R120 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W R113 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W R102 061G0402102 RST CHIPR 1 KOHM +-5% 1/16W R202 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W R304 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W R305 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W R415 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W R417 061G0402103 RST CHIPR 10 KOHM +-5% 1/16W R201 061G0402105 RST CHIPR 1MOHM +-5% 1/16W R129 061G0402151 RST CHIP 150R 1/16W 5% R133 061G0402151 RST CHIP 150R 1/16W 5% R138 061G0402151 RST CHIP 150R 1/16W 5% R218 061G0402220 RST CHIPR 22 OHM +-5% 1/16W R234 061G0402221 RST CHIPR 220 OHM +-5% 1/16W R141 061G0402222 RST CHIPR 2.2 KOHM +-5% 1/16W R142 061G0402222 RST CHIPR 2.2 KOHM +-5% 1/16W R131 061G0402391 RST CHIPR 390 OHM +-5% 1/16W R402 061G0402392 RST CHIP 3.9K 1/16W 5% R403 061G0402392 RST CHIP 3.9K 1/16W 5% R221 061G0402471 RST CHIPR 470 OHM +-5% 1/16W R316 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W R314 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W R308 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W R215 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W R214 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W R213 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W R206 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W R124 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W R123 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W http://www.wjel.net 82 HUDSON 8 R104 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W R103 061G0402472 RST CHIPR 4.7 KOHM +-5% 1/16W R307 061G0402513 RST CHIP 51K 1/16W 5% R140 061G0402750 RST CHIPR 75 OHM +-5% 1/16W R139 061G0402750 RST CHIPR 75 OHM +-5% 1/16W R101 061G0402750 RST CHIPR 75 OHM +-5% 1/16W FB105 061G0805000 0 OHM 1/10W R302 061G1206331 RST CHIPR 330 OHM +-5% 1/4W R303 061G1206331 RST CHIPR 330 OHM +-5% 1/4W C123 065G0402102 32 1000PF +-10% 50V X7R C131 065G0402102 32 1000PF +-10% 50V X7R C303 065G0402104 12 CHIP 0.1UF 50V X7R C301 065G0402104 12 CHIP 0.1UF 50V X7R C216 065G0402104 12 CHIP 0.1UF 50V X7R C215 065G0402104 12 CHIP 0.1UF 50V X7R C210 065G0402104 12 CHIP 0.1UF 50V X7R C209 065G0402104 12 CHIP 0.1UF 50V X7R C208 065G0402104 12 CHIP 0.1UF 50V X7R C207 065G0402104 12 CHIP 0.1UF 50V X7R C206 065G0402104 12 CHIP 0.1UF 50V X7R C307 065G0402104 12 CHIP 0.1UF 50V X7R C311 065G0402104 12 CHIP 0.1UF 50V X7R C312 065G0402104 12 CHIP 0.1UF 50V X7R C317 065G0402104 12 CHIP 0.1UF 50V X7R C402 065G0402104 12 CHIP 0.1UF 50V X7R C403 065G0402104 12 CHIP 0.1UF 50V X7R C404 065G0402104 12 CHIP 0.1UF 50V X7R C405 065G0402104 12 CHIP 0.1UF 50V X7R C406 065G0402104 12 CHIP 0.1UF 50V X7R C407 065G0402104 12 CHIP 0.1UF 50V X7R C101 065G0402104 12 CHIP 0.1UF 50V X7R C102 065G0402104 12 CHIP 0.1UF 50V X7R C103 065G0402104 12 CHIP 0.1UF 50V X7R C104 065G0402104 12 CHIP 0.1UF 50V X7R C105 065G0402104 12 CHIP 0.1UF 50V X7R C106 065G0402104 12 CHIP 0.1UF 50V X7R C110 065G0402104 12 CHIP 0.1UF 50V X7R C111 065G0402104 12 CHIP 0.1UF 50V X7R C112 065G0402104 12 CHIP 0.1UF 50V X7R C113 065G0402104 12 CHIP 0.1UF 50V X7R C114 065G0402104 12 CHIP 0.1UF 50V X7R C116 065G0402104 12 CHIP 0.1UF 50V X7R C117 065G0402104 12 CHIP 0.1UF 50V X7R http://www.wjel.net 83 HUDSON 8 C118 065G0402104 12 CHIP 0.1UF 50V X7R C130 065G0402104 12 CHIP 0.1UF 50V X7R C201 065G0402104 12 CHIP 0.1UF 50V X7R C203 065G0402104 12 CHIP 0.1UF 50V X7R C204 065G0402104 12 CHIP 0.1UF 50V X7R C205 065G0402104 12 CHIP 0.1UF 50V X7R C220 065G0402220 31 CHIP 22PF 50V NPO C219 065G0402220 31 CHIP 22PF 50V NPO C128 065G0402330 31 33PF +-50% 50V NPO C127 065G0402331 32 CHIP 330PF 50V X7R C132 065G040247132K T CAP CHIP 0402 470PF 50V X7R C129 065G0402473 12 CHIP 0.047uF 16V X7R C126 065G0402473 12 CHIP 0.047uF 16V X7R C125 065G0402473 12 CHIP 0.047uF 16V X7R C124 065G0402473 12 CHIP 0.047uF 16V X7R C122 065G0402473 12 CHIP 0.047uF 16V X7R C121 065G0402473 12 CHIP 0.047uF 16V X7R C316 065G0603104 22 CHIP 0.1UF 25V X7R C308 065G060310517T MLCC 0603 CAP 1UF Z 16V Y5V C304 065G060310517T MLCC 0603 CAP 1UF Z 16V Y5V C213 065G060310517T MLCC 0603 CAP 1UF Z 16V Y5V C115 065G060310517T MLCC 0603 CAP 1UF Z 16V Y5V C107 065G060310517T MLCC 0603 CAP 1UF Z 16V Y5V FB207 071G 56D102 MA CHIP HEAD 1000OHM 0805 1A FB107 071G 56D121 B201209D121TT FB205 071G 56D121 B201209D121TT FB204 071G 56D121 B201209D121TT FB203 071G 56D121 B201209D121TT FB102 071G 56D121 B201209D121TT FB101 071G 56D121 B201209D121TT FB202 071G 56D121 JA CHIP BEAD 120 OHM 0805 1A FB206 071G 56D121 JA CHIP BEAD 120 OHM 0805 1A FB302 071G 56K121 M CHIP BEAD FB303 071G 56K121 M CHIP BEAD FB106 071G 59B300 K CHIP BEAD 30 OHM 0603 FB104 071G 59B300 K CHIP BEAD 30 OHM 0603 FB103 071G 59B300 K CHIP BEAD 30 OHM 0603 D102 093G 64 42 PP BAV70 SOT-23 D110 093G 64 42 PP BAV70 SOT-23 D201 093G 64 42 PP BAV70 SOT-23 D113 093G 6433S DIODE BAV99 SEMTECH D112 093G 6433S DIODE BAV99 SEMTECH D111 093G 6433S DIODE BAV99 SEMTECH http://www.wjel.net 84 HUDSON 8 D109 093G 6433S DIODE BAV99 SEMTECH D108 093G 6433S DIODE BAV99 SEMTECH D107 093G 6433S DIODE BAV99 SEMTECH D106 093G 6433S DIODE BAV99 SEMTECH D105 093G 6433S DIODE BAV99 SEMTECH D104 093G 6433S DIODE BAV99 SEMTECH D103 093G 6433S DIODE BAV99 SEMTECH D101 093G 6433S DIODE BAV99 SEMTECH ZD201 093G 39G586 RLZ2.2B ZD107 093G 39S 24 T RLZ 5.6B LLDS ZD106 093G 39S 24 T RLZ 5.6B LLDS ZD105 093G 39S 24 T RLZ 5.6B LLDS ZD104 093G 39S 24 T RLZ 5.6B LLDS ZD103 093G 39S 24 T RLZ 5.6B LLDS ZD102 093G 39S 24 T RLZ 5.6B LLDS ZD101 093G 39S 24 T RLZ 5.6B LLDS D301 093G3004 3 SM340A U203 705GQ756019 MCU ASS'Y （LG） U203 705GQ756020 MCU ASS'Y （HSD） U203 705GQ756099 MCU ASS'Y (LPL) FQ014 KEPC7QS5 KEY BOARD ASSY CN101 033G3802 6H WAFER 6P RIGHT ANGLE PITCH 2.0 SW1 077G 600 1GCJ TACT SWITCH TSPB-2 -NP SW2 077G 600 1GCJ TACT SWITCH TSPB-2 -NP SW3 077G 600 1GCJ TACT SWITCH TSPB-2 -NP SW4 077G 600 1GCJ TACT SWITCH TSPB-2 -NP SW5 077G 600 1GCJ TACT SWITCH TSPB-2 -NP SW6 077G 600 1GCJ TACT SWITCH TSPB-2 -NP SW7 077G 600 1GCJ TACT SWITCH TSPB-2 -NP SW8 077G 600 1GCJ TACT SWITCH TSPB-2 -NP LED1 081G 12 1F GP LED 3Φ GP32032M/G307-ZY-50 R109 061G0603000 RST CHIPR 0 OHM +-5% 1/10W R101 061G0603101 RST CHIPR 100 OHM +-5% 1/10W R104 061G0603242 RST CHIPR 2.4 KOHM +-5% 1/10W R108 061G0603242 RST CHIPR 2.4 KOHM +-5% 1/10W R102 061G0603432 RST CHIPR 4.3 KOHM +-5% 1/10W R106 061G0603432 RST CHIPR 4.3 KOHM +-5% 1/10W R107 061G0603911 RST CHIPR 910 OHM +-5% 1/10W R103 061G0603911 RST CHIPR 910 OHM +-5% 1/10W R100 061G0805000 0 OHM 1/10W C101 065G0603103 32 0.01UF +-10% 50V X7R C102 065G0603103 32 0.01UF +-10% 50V X7R C103 065G0603103 32 0.01UF +-10% 50V X7R http://www.wjel.net 85 HUDSON 8 C104 065G0603103 32 0.01UF +-10% 50V X7R C105 065G0603103 32 0.01UF +-10% 50V X7R FQ015 PWPC7942GQA8 POWER BOARD ASSY Q901 057G 600 35 STP8NK80ZFP Q901 057G 667 22 FQPF8N80C D931 093G 60267 SP10100 D931 093G 60901 MBRF10H100CT ITO-220AB D935 093G 60240 YG802C06R TO-220F15 D935 093G 60526 MBRF1060CT ITO-220AB D935 093G1506 2 FMW-2156 T901 S80GL17T900V TRANSFORMER ASSY C908 063G 10747410S PLASTIC FILM CAP. C801 065G 6J1006ET 10PF 5% SL 6KV C806 065G 6J1006ET 10PF 5% SL 6KV C820 067G215D471 4K ED 470UF 25V C840 067G215D471 4K ED 470UF 25V C932 067G215S102 4K EC CAP 1000UF M 25V C933 067G215S102 4K EC CAP 1000UF M 25V L902 071G 55 24 FERRITE BEAD L903 071G 55 24 FERRITE BEAD BD901 093G 50460 10 GBU405 BD901 093G 50460 16 U4KB80R D901 093G 6026T52T RECTIFIER DIODE FR107 IC902 056G 139 3A IC PC123Y22FZ0F IC902 056G 139 3B IC PC123Y82FZ0F IC902 056G 139 5A TCET1103G NR901 061G 5810T RST NTCR 8 OHM +-20% 4A 13mm R905 061G152M104 64 100KOHM 5% 2W R920 061G152M208 64 0.20 OHM 2W C803 065G 3J5096ET 5PF 5% SL 3KV C802 065G 3J5096ET 5PF 5% SL 3KV C807 065G 3J5096ET 5PF 5% SL 3KV C808 065G 3J5096ET 5PF 5% SL 3KV C901 065G305M1022BP Y2 1000PF M 250VAC Y5P C900 065G305M1022BP Y2 1000PF M 250VAC Y5P C912 065G305M2222BP 2200PF +-20% C936 067G215D222 2K 105℃ 2200UF M 10V C936 067G215D2222KV 105℃ 2200UF M 10V C907 67G 40Z10115K CAP 105℃ 100UF M 450V L901 073G 174 65 H LINE FILTER L901 073G 174 65 LS LINE FILTER BY LISHIN L951 073G 253902 H IND CHOKE 0.8uH MIN DADO L955 073G 253902 H IND CHOKE 0.8uH MIN DADO http://www.wjel.net 86 HUDSON 8 L951 073G 253902 S IND CHOKE 0.8uH MIN TAIC L955 073G 253902 S IND CHOKE 0.8uH MIN TAIC L955 073G 253902 T CKOLE COIL 0.8uH L951 073G 253902 T CKOLE COIL 0.8uH L951 073G 253902 YS IND CHOKE 0.8uH MIN TOP L955 073G 253902 YS IND CHOKE 0.8uH MIN TOP T901 080GL17T900 L XFMR FOR POWER LITAI T901 080GL17T900 N XFMR FOR POWER YUVA T901 080GL17T900 T X'FMR SRW28LEC-T93H016 PT801 080GL19T 8DN1 X'FMR DARFONTK.2006M.101 PT802 080GL19T 8DN1 X'FMR DARFONTK.2006M.101 R915 061G 17210052T 100HM 5% 1/4W R952 061G 17210052T 100HM 5% 1/4W R871 061G 17210352T CFR 10KOHM +-5% 1/4W R861 061G 20010452T 100K OHM 1/4W 1% R863 061G 20033352T 33KOHM 1% 1/4W R861 061G203S10452T RST MFLM 100K 0.6W 1% R863 061G203S33352T RST MFLM 33K 0.6W 1% R839 061G212Y625 KT MGFR 6.2MOHM +-5% 1/2W R859 061G212Y625 KT MGFR 6.2MOHM +-5% 1/2W RJ827 061L0805000 CHIPR 0OHM +-5% 1/10W RJ801 061L0805000 CHIPR 0OHM +-5% 1/10W RJ804 061L1206000 CHIPR 0 OHM +-5% 1/8W FB902 071G 55 23 BEAD FB903 071G 55 23 BEAD FB905 071G 55 23 BEAD FB905 071G 55 23 S BEAD FB903 071G 55 23 S BEAD FB902 071G 55 23 S BEAD FB901 071G 55 29 FERRITE BEAD FB901 071G 55901 FERRITE CORE 2.5*3*1 BF3 ZD951 093G 3990352T ZD P6KE8.2A ZD951 093G 39A3552T ZENER DIODE P6KE8.2A ZOW D919 093G 6038T52T FR103 D926 093G 6038T52T FR103 D926 093G 64 5152T RGP10-DO-204AL IC941 056G 158 4 T H431BA IC941 056G 158 10 T IC AZ431AZ-AE1 TO-92 BY AAC C920 065G 1K102 5T 1000PF/1KV C931 065G517K332 2T 3.3NF 500V C927 067G 3056804KT ELCAP 68UF M 25V 105℃ K C952 067G215B2214KT "LOW E,S,R 220UF +-20% 25" C956 067G215B2214KT "LOW E,S,R 220UF +-20% 25" http://www.wjel.net 87 HUDSON 8 F902 084G 55 4 FUSE 382-5A 250V WICKMANN F901 084G 55 7 GP FUSE 3.15A 250V IC901 056G 564911 IC TEA1532AT S08 U811 056G 608 10 IC OZ9938GN-B SOIC-16 Q874 057G 417 12 T KEC 2N3904S-RTK/PS Q841 057G 600 55 P5506 HVG SO-8 Q821 057G 600 55 P5506 HVG SO-8 Q886 057G 759 2 RK7002 Q885 057G 759 2 RK7002 Q883 057G 759 2 RK7002 Q881 057G 759 2 RK7002 Q880 057G 759 2 RK7002 Q871 057G 759 2 RK7002 Q801 057G 759 2 RK7002 Q873 057G 760 4B PDTA144WK SOT346 Q841 057G 763 6 AO4828L Q821 057G 763 6 AO4828L Q841 057G 763 14 AM9945N Q821 057G 763 14 AM9945N R829 061L0805000 CHIPR 0OHM +-5% 1/10W R849 061L0805000 CHIPR 0OHM +-5% 1/10W R954 061L0805100 CHIPR 10 OHM+-5% 1/10W R843 061L0805100 CHIPR 10 OHM+-5% 1/10W R842 061L0805100 CHIPR 10 OHM+-5% 1/10W R823 061L0805100 CHIPR 10 OHM+-5% 1/10W R822 061L0805100 CHIPR 10 OHM+-5% 1/10W R835 061L0805100 2F CHIP 10K OHM 1/8W 1% R836 061L0805100 2F CHIP 10K OHM 1/8W 1% R855 061L0805100 2F CHIP 10K OHM 1/8W 1% R856 061L0805100 2F CHIP 10K OHM 1/8W 1% R851 061L0805102 CHIPR 1K OHM +-5% 1/10W R831 061L0805102 CHIPR 1K OHM +-5% 1/10W R882 061L0805102 CHIPR 1K OHM +-5% 1/10W R884 061L0805102 CHIPR 1K OHM +-5% 1/10W R886 061L0805102 CHIPR 1K OHM +-5% 1/10W R888 061L0805102 CHIPR 1K OHM +-5% 1/10W R941 061L0805102 CHIPR 1K OHM +-5% 1/10W R801 061L0805103 CHIPR 10K OHM +-5% 1/10W R804 061L0805103 CHIPR 10K OHM +-5% 1/10W R807 061L0805103 CHIPR 10K OHM +-5% 1/10W R880 061L0805103 CHIPR 10K OHM +-5% 1/10W R802 061L0805104 CHIPR 100K OHM+-5% 1/10W R872 061L0805104 CHIPR 100K OHM+-5% 1/10W http://www.wjel.net 88 HUDSON 8 R881 061L0805104 CHIPR 100K OHM+-5% 1/10W R883 061L0805104 CHIPR 100K OHM+-5% 1/10W R885 061L0805104 CHIPR 100K OHM+-5% 1/10W R887 061L0805104 CHIPR 100K OHM+-5% 1/10W R819 061L0805105 CHIP 1M OHM 5% 1/8W R912 061L0805105 CHIP 1M OHM 5% 1/8W R946 061L0805110 3F 110KOHM 1% 1/10W R833 061L0805122 "1.2KOHM +-5%,1/8W,0805" R853 061L0805122 "1.2KOHM +-5%,1/8W,0805" R923 061L0805123 CHIP 12KOHM 1/8W R914 061L0805124 1F CHIP 1.24K OHM 1/10W 1% R916 061L0805152 CHIPR 1.5K OHM +-5% 1/10 R873 061L0805202 CHIP 2KOHM 1/8W R816 061L0805203 CHIPR 20KOHM +-5% 1/8W R865 061L0805232 0F CHIP 232OHM R815 061L0805303 CHIP 30K OHM 1/8W R813 061L0805330 2F CHIP 33KOHM 1/8W 1% R874 061L0805331 CHIP 330 OHM 5% 1/10W R917 061L0805333 CHIP 33KOHM 1% 1/8W R811 061L0805335 3.3M 0805 R943 061L0805510 1F CHIP 5.1K OHM 1/10W 1% R812 061L0805624 CHIP 620KOHM 5% 0805 1/8 R825 061L0805752 CHIP 7.5K OHM 1/10W R837 061L0805752 CHIP 7.5K OHM 1/10W R944 061L0805910 1F CHIP 9.1K OHM 1/10W 1% R945 061L0805910 1F CHIP 9.1K OHM 1/10W 1% R918 061L1206000 CHIPR 0 OHM +-5% 1/8W R926 061L1206000 CHIPR 0 OHM +-5% 1/8W R907 061L1206103 CHIP 10KOHM 5% 1/4W R910 061L1206155 1.5M/0805 R904 061L1206155 1.5M/0805 R937 061L1206182 CHIP 1.8KOHM R931 061L1206229 CHIP 2.2OHM 5% 1/8W R932 061L1206229 CHIP 2.2OHM 5% 1/8W R927 061L1206472 CHIP 4.7KOHM 5% 1/4W R900 061L1206684 CHIPR 680K OHM+-5% 1/8W R901 061L1206684 CHIPR 680K OHM+-5% 1/8W R902 061L1206684 CHIPR 680K OHM+-5% 1/8W C838 065G0805102 31 1000PF 50V NPO C861 065G0805102 31 1000PF 50V NPO C819 065G0805103 22 CHIP 0.01uF 25V X7R 0805 C881 065G0805103 22 CHIP 0.01uF 25V X7R 0805 C883 065G0805103 22 CHIP 0.01uF 25V X7R 0805 http://www.wjel.net 89 HUDSON 8 C885 065G0805103 22 CHIP 0.01uF 25V X7R 0805 C887 065G0805103 22 CHIP 0.01uF 25V X7R 0805 C812 065G0805104 22 0.1UF +-10% 25V X7R 080 C832 065G0805104 22 0.1UF +-10% 25V X7R 080 C880 065G0805104 22 0.1UF +-10% 25V X7R 080 C913 065G0805104 22 0.1UF +-10% 25V X7R 080 C951 065G0805104 22 0.1UF +-10% 25V X7R 080 C955 065G0805104 22 0.1UF +-10% 25V X7R 080 C811 065G0805105 22 CHIP 1UF 25V X7R 0805 C821 065G0805105 22 CHIP 1UF 25V X7R 0805 C841 065G0805105 22 CHIP 1UF 25V X7R 0805 C846 065G0805105 22 CHIP 1UF 25V X7R 0805 C874 065G0805105 22 CHIP 1UF 25V X7R 0805 C914 065G0805105 22 CHIP 1UF 25V X7R 0805 C915 065G0805123 22 CHIP 12nF 25V X7R 0805 C860 065G0805221 22 CHIP 220PF 25V X7R 0805 C822 065G0805222 32 CHIP 2200PF 50V X7R 0805 C823 065G0805222 32 CHIP 2200PF 50V X7R 0805 C842 065G0805222 32 CHIP 2200PF 50V X7R 0805 C843 065G0805222 32 CHIP 2200PF 50V X7R 0805 C847 065G0805223 22 CHIP 0.022UF 25V X7R 080 C831 065G0805331 32 CHIP 330P 50V X7R 0805 C865 065G0805333 32 CHIP 0.033UF 50V C917 065G0805334 22 0.33UF+-10% 25V X7R 0805 C858 065G0805391 31 CHIP 390PF 50V C813 065G0805561 31 CHIP 560PF 50V NPO 0805 C941 065G0805562 21 5600PF/25V/NPO/J D831 093G 64 33 DIO SIG SM BAV99 (PHSE)R D851 093G 64 33 DIO SIG SM BAV99 (PHSE)R D833 093G 64 42 PP BAV70 SOT-23 D853 093G 64 42 PP BAV70 SOT-23 ZD874 093G 39S 24 T RLZ 5.6B LLDS ZD975 093G 39S 25 T RLZ5.1B LLDS D881 093T 64 44 S LL4148WP D883 093T 64 44 S LL4148WP D885 093T 64 44 S LL4148WP D887 093T 64 44 S LL4148WP http://www.wjel.net 90 HUDSON 8 17. Different Parts List Diversity of 190S8FB/00 compared with 190S8FS/00 190S8FB/00 190S8FS/00 Location Part No. Description Part No. Description FQ002 P33G4975 VQB1C BUTTON_OSD P33G4975 VPB1C BUTTON_OSD FQ003 P34G1829 VBE1T BEZEL L19-7phb1-S3 P34G1829 VOD1T BEZEL L19-7phb1-S3 FQ003 P34G1829 VBE1BA000 BEZEL_190S8 P34G1829 VOD1T BEZEL L19-7phb1-S3 Diversity of 190S8FB/27 compared with 190S8FS/00 190S8FB/27 190S8FS/00 Location Part No. Description Remark Part No. Description FQ016 089G1748GAA AC DVI CABLE(LPL) E089B 089G402A18N IS POWER CORD 089G404A18N YH POWER CABLE FQ017 089G1748HAA AC DVI CABLE(HSD) FQ002 P33G4975 VQB1C BUTTON_OSD P33G4975 VPB1C BUTTON_OSD FQ003 P34G1829 VBE1T BEZEL L19-7phb1-S3 P34G1829 VOD1T BEZEL L19-7phb1-S3 FQ006 Q40G 19N81320A RATING LABEL Q40G 19N81319A RATING LABEL FQ019 Q44G9071 3 EPS U203 705GQ756020 MCU ASS'Y(HSD) 705GQ756019 MCU ASS'Y CN901 087G 501 32 S AC SOCKET CN901 87G 501 32 DL AC SOCKET Second source http://www.wjel.net 91 HUDSON 8 18. General Product Specification CONTENTS 1 FOREWORD 2 PRODUCT PROFILE 2.1 LCD 2.2 SCANNING FREQUENCIES 2.3 AMBIENT TEMPERATURE: 0 °C - 35 °C 3 ELECTRICAL CHARACTERISTICS 3.1 INTERFACE SIGNALS VIDEO: 0.7 Vp-p, INPUT IMPEDANCE, 75 OHM @DC 3.2 INTERFACE 3.3 TIMING REQUIREMENT 3.4 HORIZONTAL SCANNING 3.5 VERTICAL SCANNING 3.6 POWER INPUT CONNECTION 3.7 POWER MANAGEMENT 3.8 ANALOG DISPLAY IDENTIFICATION 3.9 DVI-D DISPLAY IDENTIFECATION 3.10 USB PLUG SUPPORT 3.11 DDC/CI SUPPORT 3.12 EDID 3.13 HOT-KEY DEFINITION 3.14 SMART CONTRAST --DYNAMIC BRIGHTNESS CONTROL (DBC) (NOT REQUEIRED FOR THIS PRODUCT) 3.16 SMART IMAGE 3.17 SMART IMAGE (NOT REQUIRED FOR THIS PRODUCT) 4 VISUAL CHARACTERISTICS (DYNAMIC CONTRAST RATIO) 4.1 TEST CONDITIONS 4.2 BRIGHTNESS 4.3 IMAGE SIZE 4.4 BRIGHTNESS UNIFORMITY 4.5 CHECK CROSS TALK (S) 4.6 WHITE COLOR ADJUSTMENT 5 MECHANICAL CHARACTERISTICS 5.1 COSMETIC PHILIPS ID 5.2 MECHANICAL DATA FILES PROE FILES REQUIRED 5.3 LOCATION OF PHILIPS LOGO PER PHILIPS MAKE-UP SHEET 5.4 GAP BETWEEN PANEL AND FRONT BEZEL <0.8 (TYP) MM 5.5 LOCATION OF CONTROL ICONS PER PHILIPS GRAPHIC SHEET 5.6 COLOR FOR RESIN/PAINT PER PHILIPS MAKE-UP SHEET 5.7 RESINS 5.8 IF RAINT IS USED 5.9 PLASITIC MOLD TOOLING http://www.wjel.net 92 HUDSON 8 5.10 PLASTICS FLAMMABILITY 5.11 TEXTURE/GLOSSING OF HOUSING 5.12 TILT AND SWIVEL BASE 5.13 KENSINGTON LOCK 5.14 LABEL 5.15 PRODUCT DIMENSION/WEIGHT (PREFER TO SHT 191) 5.16 TRANSPORTATION 5.17 PALLET/CONTAINER LOADING 6. ENVIRONMENTAL CHARACTERISTICS 6.1 SUSCEPTIBILITY OF DISPLAY TO EXTERNAL ENVIRONMENT 6.2 TRANSPORTATION TESTS 6.3 DISPLAY DISTURBANCES FROM EXTERNAL ENVIRONMENT 6.4 DISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT 7. RELIABILITY 7.1 MEAN TIME BETWEEN FAILURES 8. QUALITY ASSURANCE REQUIREMENTS 8.1 ACCEPTANCE TEST 9. PHILIPS’ FLAT PANEL MONITORS PIXEL DEFECT POLICY 10 REGULATORY COMPLIANCE 10.1 WORLDWIDE REGULATORY 10.2 EMC REQUIREMENTS 10.3 ROHS 10.4 WEEE 10.5 ONGOING REGULATORY http://www.wjel.net 93 HUDSON 8 1. FOREWORD This specification describes a 19" SXGA multi-scan color TFT LCD monitor with maximum resolution up to 1280 x 1024 /75 Hz non-interlaced. All optical characteristics (including WHITE-D, Brightness, and so on) are determined according to panel specification after warming up approximate 30 minutes that brightness stability is optimal, and follow strictly after panel specification. 2. PRODUCT PROFILE This display monitor unit is a color display monitor enclosed in PHILIPS styling cabinet which has an integrated tilt base. 2.1 LCD Priority : 1. LPL/HSD 2. AUO Type : TN + film Supplier offer the Panel specification. Panel incoming specification: Follow Philips’ specification. LPL Type NR : LM190E08-TLL1/TLL4 (TN) Resolution : 1280x1024 (SXGA) Outside dimensions : Pitch ( mm ) : 0.294 mm x 0.294 mm Color pixel arrangement : RGB vertical stripes Display surface : Hard coating (3H), Anti-glare treatment of the front polarizer Color depth : 16.7 M colors (6 bits+ Hi FRC) Backlight : CCFL edge light system Active area(WxH) : View angle (CR>10 ) : 160/160 (typ) for H/V Contrast ratio :800:1 (typ) White luminance : 300 nit (typ) Color gamut :72% (typ) Gate IC : Source IC : Response time : 5 ms HSD Type NR : HSD190MEN3-A (TN) Resolution : 1280x1024 (SXGA) Outside dimensions : Pitch ( mm ) : 0.294 mm x 0.294 mm Color pixel arrangement : RGB vertical stripes Display surface : Anti-glare Color depth : 16.7 M (6 bits + Hi FRC) Backlight : CCFL edge-light(top*2/bottom*2) Active area(WxH) : View angle (CR>10) : 160/160 (typ) for H/V Contrast ratio : 1000:1 (typ) http://www.wjel.net 94 HUDSON 8 White luminance : 300 nits (typ) Color gamut : 72% (typ) Gate IC : Source IC : Response time : 5ms 2.2 Scanning frequencies Hor. : 30 – 83 K Hz Ver.: 56 - 76 Hz Video dot rate: 165 MHz Power input: 90-264 V AC, 50/60 ± 2 Hz Power consumption : : 36 W typical Functions: (1)D-SUB analog R/G/B separate inputs, H/V sync separated, Composite (H+V) TTL level, SOG sync (2) DVI digital Panel Link TMDS inputs 2.3 Ambient temperature: 0 °C - 35 °C 3. Electrical characteristics 3.1 Interface signals 1). D-Sub Analog Input signal : Video, Hsync., Vsync Video : 0.7 Vp-p, input impedance, 75 ohm @DC Sync. : Separate sync TTL level , input impedance 2.2k ohm terminate Hsync Positive/Negative Vsync Positive/Negative Composite sync TTL level, input impedance 2.2k ohm terminate (Positive/Negative) Sync on green video 0.3 Vp-p Negative (Video 0.7 Vp-p Positive) 2). DVI-D Digital Input signal: Single TMDS link (Three channels: RX0-/+, RX1-/+, RX2-/+) 3.2 Interface 3.2.1 D-Sub Cable Length : 1.8 M +/- 50 mm Connector type : D-Sub male with DDC2B pin assignments. Blue connector thumb-operated jack screws http://www.wjel.net 95 HUDSON 8 Pin assignment: Pin No. Signal 1 Red 2 Green/ SOG 3 Blue 4 Sense (GND) 5 Cable Detect (GND) 6 Red GND 7 Green GND 8 Blue GND 9 DDC +3.3V or +5V 10 Logic GND 11 Sense (GND) 12 Bi-directional data 13 H/H+V sync 14 V-sync 15 Data clock 3.2.2 DVI Cable The input signals are applied to the display through DVI-D cable. Length. : 1.8 M +/- 50 mm Connector type . : DVI-D male with DDC-2B pin assignments White connector thumb-operated jackscrews http://www.wjel.net 96 HUDSON 8 Pin Assignment: Pin No. Description 1 T.M.D.S. data2- 2 T.M.D.S. data2+ 3 T.M.D.S. data2 shield 4 No Connect 5 No Connect 6 DDC clock 7 DDC data 8 No Connect 9 T.M.D.S. data1- 10 T.M.D.S. data1+ 11 T.M.D.S. data1 shield 12 No Connect 13 No Connect 14 +5V Power 15 Ground (for +5V) – Cable detect 16 Hot plug detect 17 T.M.D.S. data0- 18 T.M.D.S. data0+ 19 T.M.D.S. data0 shield 20 No Connect 21 No Connect 22 T.M.D.S clock shield 23 T.M.D.S. clock+ 24 T.M.D.S. clock- 3.3 Timing requirement Factory Preset mode definition : 1. Perfect FOS (except PHASE) while presenting all required timings. 2. Required timings need to be specified in User's Manual Preset mode definition : 1. Need to support those timings. 2. Perfect FOS after auto adjustment. User mode 1. Can save those timing that not in Preset mode and can be showed (not over scalar or Panel spec.) 2. It needs to reserve the 12 timings space in memory size. 3.3.1 Mode storing capacity Factory preset modes : 11 Preset modes : 45 User define modes : 12 Note: 1. Screen displays perfect picture at 11 factory-preset modes. 2. Screen displays visible picture with OSD warning when input modes are the 45 preset modes. http://www.wjel.net 97 HUDSON 8 3.3.2 Factory preset modes (11 modes) Factory modes and preset modes are defined in the enclosed timing table file. Item H.Freq. (KHz) Mode Resolution V.Freq. (Hz) BW(MHz) 1 31.469 IBM VGA 10H 640x350 70.086 25.175 Y 2 31.469 IBM VGA 3H 720x400 70.087 28.322 Y 3 31.469 IBM VGA 12H 640x480 59.94 25.175 Y 4 35 MACINTOSH 640x480 66.667 30.24 Y 5 37.861 VESA 640x480 72.809 31.5 Y 6 37.5 VESA 640x480 75 31.5 Y 7 43.269 VESA 640x480 85.008 36 Y 8 35.156 VESA 800x600 56.25 36 Y 9 37.879 VESA 800x600 60.317 40 Y 10 48.077 VESA 800x600 72.188 50 Y 11 46.875 VESA 800x600 75 49.5 Y 12 53.674 VESA 800x600 85.061 56.25 Y 13 49.725 MACINTOSH 832x624 74.55 57.283 Y 14 56.4 - 960x720 75 N 15 44.75 - 960x720 60 N 16 48.363 VESA 1024x768 60.004 65 Y 17 56.476 VESA 1024x768 70.069 75 Y 18 60.023 VESA 1024x768 75.029 78.75 Y 19 61.08 IBM XGA-2 1024x768 75.782 86.001 Y 20 68.677 VESA 1024x768 84.997 94.5 Y 21 47.396 CVT 2.3MA 1280 x768 59.995 68.25 Y 22 60.289 CVT 2.3MA 1280 x768 74.893 102.25 Y 23 53.7 1152x864 60 81.624 Y 24 63.851 VESA 1152x864 70.012 94.5 Y 25 67.5 VESA 1152x864 75 108 Y 26 68.681 MACINTOSH 1152x870 75.62 100 Y 27 61.82 SUN WS 1152x900 65.977 92.978 Y 28 71.713 SUN WS 1152x900 76.047 105.561 Y 29 60 VESA 1280x960 60 108 Y 30 75.171 VESA 1280x960 75.021 129.895 Y 31 63.981 VESA 1280x1024 60.02 108 Y 32 71.691 SUN WS 1280x1024 67.189 117 Y 33 76.754 DOS/V 1280x1024 72.001 129.56 Y 34 79.976 VESA 1280x1024 75.025 135 Y 35 81.13 SUN WS 1280x1024 76.107 135 Y http://www.wjel.net 98 HUDSON 8 36 91.146 VESA 1280x1024 85.24 157.5 Y 37 44.772 - 1280x720 59.855 74.5 Y 38 56.456 - 1280x720 74.777 95.75 Y 39 64.744 CVT-reduced bl ki 1400x1050 59.948 101 N 40 82.278 CVT 1400x1050 74.867 156 N 41 93.881 CVT 1400x1050 84.96 179.5 N 42 55.469 VESA-reduced bl ki d 1440x900 59.901 88.75 Y 43 55.935 VESA 1440x900 59.887 106.5 Y 44 70.635 VESA 1440x900 74.984 136.75 Y 45 75 VESA 1600x1200 60 162 Y 46 66.587 CVT 2.3MA-R 1920x1080 59.934 (for DVI D) 138.5 Y 47 65.29 CVT1.76MW 1680x1050 59.954 146.25 Y 48 64.674 CVT1.76MW-R 1680x1050 59.883 119 Y 49 74.038 CVT 2.3MA-R 1920x1200 59.95 (for DVI D) 154 Y 50 61.648 1600x1000 59.91 108.5 Y 3.3.3 Software control functions via OSD / control adjustable functions: Please refer to following Hudson8 OSD definitions Reset - No: Exit Yes: Auto adjustment for displaying timing mode and recall factory preset OSD Languages –8 Power On Logo: Power On � show up Philips logo 3 second � change to input signal This picture is reference only. The official drawing will send out by PM. http://www.wjel.net 99 HUDSON 8 OSD Tree 3.4 Horizontal scanning Sync polarity : Positive or Negative Scanning frequency : 30 – 83 K Hz 3.5 Vertical scanning Sync polarity : Positive or Negative Scanning frequency : 56 - 76 Hz http://www.wjel.net 100 HUDSON 8 3.6 Power input connection Power cord length : 1.8 M Power cord type : 3 leads power cord with protective earth plug. 3.7 Power management The monitor must comply with the Microsoft On Now specification, and meet EPA requirements. Mode HSYNC VSYNC Video Power-cons. Indication Rec. time Power-On On On active 36W typical Green LED -- Off Off Off blanked < 1 W Amber LED < 3 s DC Power Off N/A < 1 W LED Off 3.8 Display identification In accordance with VESA Display Channel Standard Ver.1.0 and DDC 2B capability 3.9 Display identification In accordance with DVI requirement (DDWG digital Visual Interface revision 1.0) use DDC-2B, DDC/CI, and EDID V1.3 3.11 DDC/ CI Support In accordance with VESA DDC/CI and MCCS ver.2.0, the monitor should be workable with Protrait Display Tune at least. 3.12 EDID Data for EDID & .inf file 1 User visible strings on .inf file Philips 190S (19inch LCD MONITOR 190S8) 2 Manufacturer ID ( EDID data) PHL 3 Product ID, "xxxx" 4 codes MSB(byte 12): 08 LSB (byte 11): 59 4 maximum resolution 1280x1024 5 Horizontal Frequency Range 30~83 KHz 6 Vertical Frequency Range 56~76Hz 7 Monitor Name (13 characteries max.) Philips 190S 3.13 Hot-key definition Key Key Press Time OSD Timeout Monitor Controls Lock OK(Menu) 6 sec (lock/unlock) 3 sec Factory Mode AUTO+ OK+ Power On Keep pressing when power on Demo mode for smart image Smart Image Key 3 sec (Enter/Quit) DDC/CI On/OFF for VISTA MENU+DOWN 6 sec (lock/unlock) 3 sec http://www.wjel.net 101 HUDSON 8 3.14 Smart contrast (Dynamic contrast ratio) Smart Contrast is a kind of dynamic backlight control. This function changes the panel backlight dynamically according to the frame brightness histogram. the contrast ratio has to be 3000:1(typical). 3.15 Smart Image 3.15.1Smart Image OSD outlook (Economic � Economy) 3.15.2Smart Image OSD outlook 3.15.2.1 Position Pressing the “Smart Image” button, the position is in the bottom center of the screen. 3.15.2.2 Smart Image Logo & Banner As design to keep the Light Frame logo at header but change the name to “SmartImage” with bitmap format. 3.15.2.3 Icon of each profile Each profile will use text instead of icon & text before. 3.15.2.4 User Operation Procedure A. 5 different modes are switched to next in the sequence from 1 to 5 then back to 1 while pressing this button: 1) Office Work 2) Image Viewing 3) Entertainment 4) Economy 5) Off. The default setting is ‘Off”. B. The FOS optimization will be changed in real time by which profile to be scrolled, users don’t need to confirm to enable. C. The Smart Image OSD will remain on screen for 5 seconds after user last action. Or user can also press [MENU] to close the Smart Image OSD immediately. D. Except using [MENU] button to scroll down profile. If Smart Image OSD already launched onscreen. User is allowed to use up/down key to choose profile and press [MENU] to confirm selection and close the Smart Image OSD. E. If the model has multiple inputs including VGA and DVI, each input has their own set of profiles. When user switch input, the profile to be applied will also change. F. Each input can memorize their individual “Smart Image” profile status. For example, Smart Image is on with “Office” profile at VGA input, when switch to DVI input, the Smart Image will revert to previous profile of DVI. In the input switching process the “Smart Image” OSD will also show up to present which profile is selected if “Smart Image” is enabled at that input. The Smart Image status will also be stored after the monitor is resumed from AC on/off or power switch on/off. 3.15.2.5Linkage between Smart Image OSD and main OSD A. Settings within main OSD have linkage with Smart Image OSD. http://www.wjel.net 102 HUDSON 8 i. Brightness ii. Contrast iii. Color Temperature B. Because each preset profiles will define default setting of these 3 parameters. Users can understand what is the value of that in preset profile by open the main OSD. C. When any SmartImage Lite profile had been enabled. The parameters in main OSD are still available for user to adjust. But these adjustments are temporary only. If users switch to another profile and then go back. The setting in main OSD will show preset values of that Smart Image profile enabled. 3.15.2.6 Profile Definitions (system integrators to input at design stages) A. Office Work i Purpose: Design for general office application, like word processing, Spreadsheet and email. The screen is dominated by text. ii. Enhancement point: 1.A little sharpness for increasing the details of e.g. an excel grid. No other type of enancement as it won't bring value. 2. Color temperature remains in 6500°K. 3. Brightness level should be 70%. 4. Smart Response set to “Off”. 5. Smart Contrast set to “Off”. B. Entertainment i. Purpose: Design for video application, Like Microsoft Media Player or Real Player. The screen is dominated by video. ii Enhancement Point: 1. Dynamic contrast enhancement by histogram analysis (DLC) should be implemented. 2. Sharpness enhanced 90%. 3. Color enhancement set as the same with Video. 4. Color temperature set to 7500° (Based on final PQ settings) (if higher) 5. Brightness level sets to maximum. 6. SmartResponse set to “High”.(N/A for this model) 7. Gamma Table turn off to achieve 8. Fastest response time. (N/A for this model) 9. Smart Contrast set to “On” C. Image Viewing i. Purpose: Design for image viewing application, especially in slide show. The screen is dominated by picture. Powerpoint presentation could use this profile also. ii. Enhancement Point: 1.Dynamic contrast enhancement by histogram analysis (DLC) should be off. 2. Sharpness and color to be enhanced 75%. 3. Color temperature 6500°K 4. Brightness level sets to maximum. 5. Smart Response set to “Off”. (N/A for this model) 6. Smart Contrast set to “Off”. D. Economy i.Purpose: Adjust brightness level for reducing power consumptions http://www.wjel.net 103 HUDSON 8 ii.No optimization by Smart Image. iii.Design: 1. Brightness level set to 70%, a little higher brightness level than laptop PC, fine tune brightness level before DVT exit. 2. Color temperature set to 6500K. 3. Gamma Table is turn on. E. Off i. Purpose: No optimization by SmartImage. ii. Design: 1. This will follow user OSD setting. If any change by user, it will be saved. When switch back from other SmartImage profiles, it will go back to last saved setting. 2. Gamma Table is turn on to reduce bad color tracking. 3.15.2.7Demo mode A. Purpose: Built-in demo mode for sales in-store demo. B. Design: i. Dynamically split screen to 2 vertical frames with one vertical white line. The line width is 2 pixels. The left frame will be enhanced by SmartImage and right frame remains original performance. ii. There is OSD showing “SmartImage On” in left frame and “SmartImage Off ” in right frame. iii. The OSD word color is white with transparent background. C. The demo profile will be “entertainment profile setting. D. Hot keys to trigger: Press [Smart Image] 3 seconds or more to trigger the demo mode. When demo mode is On, press 3 seconds or more to turn off the demo mode. When the demo mode is enabled, the blue LED will flash until demo mode disabled.(N/A for this model) 4. Visual characteristics 4.1 Test conditions Unless otherwise specified, this specification is defined under the following conditions. (1) Input signal : As defined in 3.3, 1280 x 1024 non-interlaced mode (1280 x 1024@60Hz 108MHz), signal sources must have 75 ohm output impedance. (2) Luminance setting : controls to be set to 300 nits (typical) with full screen 100 % duty cycle white signal (3) Warm up: more than 30 minutes after power on with signal supplied. (4) Ambient light: 400 -- 600 lux. (5) Ambient temperature: 20 ± 5 °C 4.2 Brightness Follow Panel specification. 4.3 Image size Actual display size 373.3 x 301.1 mm 4.4 Brightness uniformity Set contrast at 100% and turn the brightness at 100%. Apply the Fig 1, it should comply with the following formula: http://www.wjel.net 104 HUDSON 8 B_min X 100% >75% B_max Where B_max =Maximum brightness, B_min = Minimum brightness 4.5 Check Cross talk (S) Apply Pattern 2. Set contrast and brightness at 100 %. Measure YA. Then output Pattern 3 and measure YB. the cross talk value : ABS ( YA - YB ) ⎯⎯⎯⎯⎯⎯⎯⎯⎯ X 100% < 1.5 % YA 4.6 White color adjustment There are seven factory preset white color 11500K, 9300K, 8200K, 7500K, 6500K, sRGB, 5000K Apply full gray64 pattern, with brightness in 100 % position and the contrast control at 50 % position. The 1931 CIE Chromaticity (color triangle) diagram (x ,y) coordinate for the screen center should be: Product specification CIE coordinates (x,y) 11500K x = 0.272 ± 0.02 y = 0.283 ± 0.02 9300K x = 0.283 ± 0.02 y = 0.297 ± 0.02 8200K x = 0.292 ± 0.02 y = 0.307 ± 0.02 7500K x = 0.299 ± 0.02 y = 0.315 ± 0.02 6500K/sRGB x = 0.313 ± 0.02 y = 0.329 ± 0.02 sRGB x = 0.313 ± 0.02 y = 0.329 ± 0.02 5000K x = 0.346 ± 0.02 y = 0.359 ± 0.02 http://www.wjel.net 105 HUDSON 8 Production alignment spec. CIE coordinates (x,y) 11500K x = 0.272 ± 0.005 y = 0.283 ± 0.005 9300K x = 0.283 ± 0.005 y = 0.297 ± 0.005 8200K x = 0.292 ± 0.005 y = 0.307 ± 0.005 7500K x = 0.299 ± 0.005 y = 0.315 ± 0.005 6500K/sRGB x = 0.313 ± 0.005 y = 0.329 ± 0.005 sRGB x = 0.313 ± 0.005 y = 0.329 ± 0.005 5000K x = 0.346 ± 0.005 y = 0.359 ± 0.005 Quality Inspection specification: CIE coordinates (x,y) 9300K x = 0.283 ± 0.015 y = 0.297 ± 0.015 6500K/sRGB x = 0.313 ± 0.015 y = 0.329 ± 0.015 sRGB x = 0.313 ± 0.015 y = 0.329 ± 0.015 5. Mechanical characteristics 5.1 Cosmetic - Philips ID 5.2 Mechanical data files - ProE files required 5.3 Location of Philips logo - Per Philips make-up sheet 5.4 Gap between panel and front bezel < 0.8 (typ) mm 5.5 Location of Control icons - Per Philips Graphic sheet 5.6 Color for resin/paint - Per Philips make-up sheet 5.7 Resins � RoHS required � WEEE required. � Resin type/selection refer to Project Book Section 7.2 Plastic material. http://www.wjel.net 106 HUDSON 8 5.8 If paint is used � RoHS required � WEEE require � If new painting type need to implement, refer to UN-D 1235. 5.9 Plastic mold tooling � Tooling to be designed to minimize cosmetic defects induced by molding process (sink, blush, weld lines, gate marks, ejector marks, etc.). Refer to “TYV61-90007”. � Painting to cover up cosmetic defects due to molding is strongly discouraged. 5.10 Plastics flammability � All Plastics to be Flame Retardant UL 94-V0 or Better (if monitor weighs less than 18kg; UL94-V0 is OK). � Base / Pedestal to be Flame Retardant UL 94-HB. � All major plastic parts (bezel, back cover, base) need to be molded from same resin. � ABS V0 is allowed to implement in China region for monitor body major plastic parts (bezel, back cover, base). � Plastic resin type selection should be referred to “TY R83-2-9002-1”s. 5.11 Texture/Glossing of housing � The texture area and texture no should follow Philips make-up sheet. � The exterior surfaces shall have a uniform texture. � Philips must approve the mold texturing. � Detail document for texture refer to “UN-D249”, “UN-D 600”. � < = 20 gloss units 5.12 Tilt and swivel base � Tilt angle : -5 ° +2/- 0 ° (forward) +20 °+3/-0 ° (backward) � Swivel angle : ±45° ( not request for 190S8 ) � High Adjustment : 130mm ( not request for 190S8 ) � Portrait Display : -1° +1/-0°~+91° +0/-1° CCW ( not request for 190S8 ) 5.13 Kensington Lock � Must meet Kensington_slot.spec “TYE-M0004”. � MMD request metal plate in Kinsington hole. 5.14 Label � Regulatory label / Carton label should follow Philips requirement. � China RoHS label � Detail document refer to Philips Engineering Reference Book. http://www.wjel.net 107 HUDSON 8 5.15 Product dimension / Weight (Refer to SHT 191 ) � Unit dimension : 424.05mm (W) * 418.8 (H) * 210.82mm(D) � Packed unit dimension : ???mm(W) * ???mm(H) * ??? mm(D) for WW : 492mm(W) * 456mm(H) * 175 mm(D) for China � Net weight : ?Kg (Including I/F cable ? g) � Gross weight : ? Kg for WW : ? Kg for China 5.16 Transportation Transportation standards refer to TYE-M0002. 5.16.1 Transportation packages Packaging and wrapping shall be sufficient to protect the product against damage or loss during shipment from the supplier to the destination specified in the purchase order. All packaging materials are subject to test and evaluation per TYE-M0002. The cushion material shall be constructed using EPS material. 5.16.2 Transportation Test The overall test refer to TYE-M0002. Vibration, drop test should be performed at ambient temperature(20°C to 23oC) and relative humidity (40% to 65% ). A. Transportation test specification for all regions except China/India • Package test 1. Random Vibration test 2. Drop test 3. Cold Drop test (for design reference) • Un-package test 1. Half sine shock test (non operation) B. Transportation test specification for China/India • Package test 1. Random Vibration test 2. Drop test 3. Cold Drop test (for design reference) • Un-package test 1. Sine vibration (operating) 2. Half sine shock test (non operation) http://www.wjel.net 108 HUDSON 8 5.17 Pallet / Container loading Transportation standards refer to TYE-M0002. � Air shipment - � Sea container 20'(pallet/slip sheet) � Sea container 40'(pallet/slip sheet) � Sea container 40' High Cube (pallet/slip sheet) � Truck shipment- Transportation request for all region except China/India A. Air shipment B. Container loading for WW Transportation request for China and India A. Container loading for China and India B. Truck loading 6. Environmental characteristics The following sections define the interference and susceptibility condition limits that might occur between external environment and the display device. 6.1 Susceptibility of display to external environment Operating - Temperature : 0 to 35 degree C - Humidity : 80% max - Altitude : 0-3658m - Air pressure : 600-1100 mBAR Storage - Temperature : -20 to 60 degree C - Humidity : 95% max - Altitude : 0-12192m - Air pressure : 300-1100 mBAR Note: recommend at 5 to 35°C, Humidity less than 60 % 6.2 Transportation tests Refer to 5.15.2 6.3 Display disturbances from external environment According to IEC 801-2 for ESD disturbances 6.4 Display disturbances to external environment 7. Reliability 7.1 Mean Time Between Failures System MTBF (Including the LCD panel and CCFL) : 50,000 hrs 8. Quality assurance requirements http://www.wjel.net 109 HUDSON 8 8.1 Acceptance test According to MIL-STD-105D Control II level AQL: 0.4 (major) 1.5 (minor) (Please also refer to annual quality agreement) Customer acceptance criteria: UAW0377/00 9. Philips’ Flat Panel Monitors Pixel Defect Policy Philips’ Flat Panel Monitors Pixel Defect Policy BRIGHT DOT DEFECTS ACCEPTABLE LEVEL MODEL 190S8 1 lit sub-pixel 3 2 adjacent lit sub-pixels 1 3 adjacent lit sub-pixels (one white pixel) 0 Distance between two bright dots 15mm Bright dot defects within 20 mm circle 0 Total bright dot defects of all type 3 BLACK DOT DEFECTS ACCEPTABLE LEVEL MODEL 190S8 1 dark sub-pixel 5 2 adjacent dark sub-pixels 2 3 adjacent dark sub-pixels (one white pixel) 1 Distance between two black dots 15mm Black dot defects within 20 mm circle* 1 Total black dot defects of all type 5 TOTAL DOT DEFECTS ACCEPTABLE LEVEL MODEL 190S8 Total bright or black dot defects of all type 5 http://www.wjel.net 110 HUDSON 8 Fig 1: Measurement locations of Brightness Uniformity Fig 2: Cross talk pattern Gray level 46 (64 Gray level) YA 1/2 1/2 1/6 Fig 3: Cross talk Pattern Center at Gray level 0 (Black) YB 1/2 1/2 1/6 1/3 1/3 1/3 1/3 1/3 http://www.wjel.net 111 HUDSON 8 D VIDEO C E SEPARATE SYNC. HORIZONTAL B A R VIDEO Q S P O D VIDEO C E B A VERTICAL HORIZONTAL COMPOSITE SYNC. FIG-4 TIMING CHART -1 http://www.wjel.net 112 HUDSON 8 10. REGULATORY COMPLIANCE 10.1 Worldwide Regulatory Country Domain Safety / EMC / Ergonomics / Standards Documents International Sa IEC60950-1:2001. Group -and national differences of all countries listed in CB Bulletin No. 107A CB Report and CB certificate Sa European Low Voltage Directives 73/23/EEC and 93/68/EEC Declaration of Conformity European Electromagnetic Compatibility Directive 89/336/EEC amended by the directive 93/68/EEC. EN 55022:1998 Class B EN 55024: 1998 EN 61000-3-2: 2000 IEC 61000-3-3: 1994/EN61000-3-3: 1995 Europe E CISPR 22:1997 Class B International EMC standard Declaration of Conformity and Full EMC/CE test report Sa EN60950-1:2001 TUV certificate O ISO 13406-2: 2001 & prEN 50279:1998 TUV-ERG certificate Germany O GS-Mark / EK1-ITB 2000 TUV-GS certificate Sa EN60950-1:2001 SEMKO certificate Sweden O TCO 99 (TCO03) TCO99 (TCO03) report + certificate Russia Sa GOST R 50377-1992 GOST certificate http://www.wjel.net 113 HUDSON 8 South Africa Sa SABS IEC 60950 Certificate of Conformity Sa UL 60950-1: 2003 UL certificate E FCC Part 15 Class B FCC ID grant USA O Energy Star EPA registration Sa CSA C22.2 No 60950 CSA certificate Canada E ICES-003 issue 3 Statement on label Mexico Sa NOM-019-SCFI-1994 NOM certificate Sa Korean Safety Control law IEC 60950 eK certificate Korea E Regulations laws: EMI 1996-78, 80. EMS 1996-79,81 MIC certificate Singapore Sa IEC60950 PSB certificate Sa GB4943-2001 China E GB9254-1998; 17625.1-2003 CCC certificate Sa CNS-14336 (IEC 60950-1) Taiwan E CNS-13438 (CISPR22) Class B BSMI certificate Sa = Safety E = Electromagnetic Compatibility O = Other which including recycling, energy saving, ergonomics http://www.wjel.net 114 HUDSON 8 10.2 EMC Requirements Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must be submitted again prior to PVT samples delivery, which also has to meet Philips' immunity testing specification. 10.3 RoHS Restriction on the use of certain hazardous substances. Lead, Cadmium, Mercury, Hexavalent Chromium, Polybrominated Bipheny1 (PBB) and Polybrominated Bipheny1 Ether (PBDE)(flame retardant). 10.4 WEEE Producer (Philips) responsible for retailer take back schemes and recycling. --System implemented. --Collection and recycle targets. 10.5 Ongoing Regulatory There's a possibility that other regulatory certificates will be required during the life of the product. It is the responsibility of the supplier to provide related documentation. http://www.wjel.net