Description Page Important Safety Notice---- ------------------------------ 2 Technical Data----------------------------------------------3 Instalation&On Screen Display---------------------4~12 ------------------------------------ Lock/unlock,Aging,Factory mode ---------------------14 ------------------------------ Mechanical Instructions----------------------------16~17 Color adjustment -----------------------------------------18 Warning Message ----------------------------------------19 Troubleshooting--------------------------------------20~21 Electrical instruction --------------------------------22~26 DDC Instructions-------------------------------------27~33 DDC DATA --------------------------------------------34~35 ISP Instructions --------------------------------------36~37 Circuit Description ----13 Philips Pixel Defect Policy 15 Horizontal frequencies 30 - 63 kHz Service Service Service TABLE OF CONTENTS Published by BCU Monitors Printed in Suzhou Copyright reserved Subject to modification K Aug. 05 2005 Description Page Failure mode of panel-----------------------------------38 Wiring&Block Diagram-----------------------------39~40 Scaler Diagram&C.B.A. ---------------------------41~58 Power Diagram&C.B.A. ---------------------------59~61 Control Diagram&C.B.A.-------------------------------62 DSUB Diagram&C.B.A.---------------------------------63 IR Diagram & C.B.A. ------------------------------------64 Exploded View -------------------------------------------65 Spare& parts list-----------------66~71 General product specification ------------------72~103 Repair tips ----------------------------------------104~105 Repair Flow chart--------------------------------106~107 Different parts list--------------------------------------108 Safety Test Requirments -----------------------------109 Recommended REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING. ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. SAFETY NOTICE Chassis: BDS GB 3138 106 10486 32 inch WXGA TFT LCD Monitor/TV BDL3221V/00 BDL3221V/27 BDL3221VS/00 320WN6QS/93 320WN6QS/97 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 Important Safety Notice 2 BDL3221 LCD/TV Go to cover page Proper service and repair is important to the safe, reliable operation of all Philips Consumer Electronics Company** Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended. It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Philips could not possibly know, evaluate and advise the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Philips has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Philips must first satisfy himself thoroughly that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected. * * Hereafter throughout this manual, Philips Consumer Electronics Company will be referred to as Philips. WARNING Critical components having special safety characteristics are identified with a by the Ref. No. in the parts list and enclosed within a broken line* (where several critical components are grouped in one area) along with the safety symbol on the schematics or exploded views. Use of substitute replacement parts which do not have the same specified safety characteristics may create shock, fire, or other hazards. Under no circumstances should the original design be modified or altered without written permission from Philips. Philips assumes no liability, express or implied, arising out of any unauthorized modification of design. Servicer assumes all liability. * Broken Line Take care during handling the LCD module with backlight unit - Must mount the module using mounting holes arranged in four corners. - Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen. - Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to the panel. - Protect the module from the ESD as it may damage the electronic circuit (C-MOS). - Make certain that treatment person s body are grounded through wrist band. ! ! 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 3 Technical Data Go to cover page BDL3221 LCD/TV Pin Assignment Input DVI-D connector pin Red video input Green video input Blue video input GND Cable detect Red video GND Green video GND Blue video GND DDC +5V GND GND Serial data line (SDA) H-sync V-sync Data clock line (SCL) 7 8 6 5 4 3 2 1 9 10 11 12 13 14 15 Pin No. Pin No. Assignment Assignment Pin No. Description 1 T.M.D.S. data2- 2 T.M.D.S. data2+ 3 T.M.D.S. data2 shield 4 No Connect 5 No Connect 6 DDC clock 7 DDC data 8 No Connect 9 T.M.D.S. data1- 10 T.M.D.S. data1+ 11 T.M.D.S. data1 shield 12 No Connect 13 No Connect 14 +5V Power 15 Ground (for +5V) - Cable detect 16 Hot plug detect 17 T.M.D.S. data0- 18 T.M.D.S. data0+ 19 T.M.D.S. data0 shield 20 No Connect 21 No Connect 22 T.M.D.S clock shield 23 T.M.D.S. clock+ 24 T.M.D.S. clock- LCD panel Type NO : LC320W01 A6K3 (Supplier LPL) Display area(mm) : 697.685mm x 392.256mm Number of Pixels : 1366(H) x 768(V) Pitch ( mm ) : 0.170mm(H) x 0.510mum(V) Color pixel arrangement : RGB vertical stripe Display operating mode : Normally black Color depth : 16,7M colors ( 8 bits) Brightness (cd/m^2) : 500(Center 1 points, Typ.) Viewing angle(CR>10) : Viewing angle free(R/L 178(Typ.),U/D 178(Typ.)) Surface treatment : Hard coating(3H),Anti-glare treatment of the front polarize Electrical interface : LVDS Response Time (ms, Typ) : TrR:8,TrD:10(Gray to Gray) Contrast ratio : Typical 1000 : 1 with AI Outline Dimension : 760 mm(H) x 450 mm(V) x 48(D) mm (Typ.) Module weight (g) : 7200g(Typ.) Backlight : 20 EEFL Power supply AC-input : 90V ~ 264VAC,50/60�2Hz Power consumption : 100W/Typ(at PC mode), 130W/Typ(at TV mode). Power cord length : 1.8M Power cord type : European type and UK type Power indicator : LED (On: Blue ,Sleeping mode: Amber ) Auto power saving : < 5W Horizontal scan : 30 ~ 63KHz Vertical scan : 50 ~ 75 Hz Environmental conditions Operating - Temperature : 0 to 40 - Humidity : 10 to 90% - Altitude : 0-12,000 feet - Air pressure : 645 mBAR - (guaranteed optical performance) : 5 to 35 - (guaranteed functional performance) : 5 to 40 Storage - Temperature : -20 to 50 - Humidity : 10- 90% (non-condensing ) - Air pressure : 600-1100 mBAR Note: recommend at 0 to 35�C, Humidity less than 60 % Shipping - Temperature :( -20 to 60 ) - Humidity : 5- 90% (non-condensing ) - Altitude : 0-40000 feet ( non operating ) Air pressure : 188-1100 Mbar Power Management Definition VESA Mode Video H-sync V-sync Power Used LED color Active On Yes Yes 100 W (typ.) Blue Sleep Off No No < 5 W Amber Switch Off Off - - < 3 W Off 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 4 Go to cover page BDL3221 LCD/TV Installation Item Description Installing your LCD Monitor/TV Side View (Left) 1 INPUT Selecting input source 2 Increase or decrease the channel number or moving up or down to highlight the function in OSD 3 Increase or decrease the level of audio volume or moving left or right to highlight the sub-menu in the selected function of OSD 4 MENU Open the OSD or confirm the selected function 5 DC power switch On/Off Side View (Right) 1 Audio input for composite input Audio (left and right) in put for compo site signal in put. 2 Composite input Composite (CVBS) signal input 3 S-Video input S-Video signal input 4 Earphone output Earphone output 5 TV tuner TV tuner input (available in TV version only) Rear View 1 AC in AC power in 2 Speakers output External speakers output 3 D-Sub output PC analog D-Sub input 4 DVI-D input PC digital input 5 D-Sub input PC analog D-Sub input 6 RS232 input RS232 network connection Input 7 RS232 output RS232 network connection output for the use of loop through function 8 PC audio PC stereo audio input 9 Audio input for component signal Audio (left and right) input for component signal input 10 Component input Component (YPbPr ) signal input 11 Composite output Composite (CVBS) output for the use of loop through function 12 Audio output for composite output Audio (left and right) out put for compo site signal out put. 13 External / EURO-AV SCART connection (for the use of European model only) 14 Kensington lock Kensington lock Accessory Pack Unpack all the parts Power cable Remote control & batteries DVI-D cable VGA signal cable E-DFU pack Accessories below are available for TV model only Item Description Base Screw pack 2x10 W Detachable Speakers 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 5 Go to cover page BDL3221 LCD/TV Installation Setting up and connecting your monitor/TV - Connecting the monitor/TV Connect the cables to the rear of your monitor/TV according to the numbers: TV model � - Connect to PC Connect the cables to the back of your computer by following step 1~5. If your monitor displays the computer image the installation has been completed successfully. If installation was not successful, see the Troubleshooting section. For installation of the monitor driver for Microsoft Windows , see the Monitor Driver Installation section (Getting Started). � � � � R - Connect to DVD/VCD/VCR Connect to DVD/VCR/VCD through S-VIDEO Connect to DVD/VCR/VCD through S-VIDEO � � Connect to DVD/VCR /VCD through SCART (for Europe only) � Connect to DVD/VCR /VCD through composite video (CVBS) � Connect to DVD/VCR /VCD through component video (YPbPr) Connecting to Cable TV Antenna Progressive video and HDTV connections for digital high-definition picture 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 6 Go to cover page BDL3221 LCD/TV On Screen Display On Screen Display Controls An overall view of the On-Screen Display (OSD) structure is shown below. You can use it as a reference for further adjusting your Monitor/TV. There are two different modes of OSD available for different models: PC Mode TV Mode � � Main menu There is a slight difference between PC mode and TV mode: Setup selection is available in TV mode only. 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 7 Go to cover page BDL3221 LCD/TV On Screen Display 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 8 Go to cover page BDL3221 LCD/TV On Screen Display 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 9 Go to cover page BDL3221 LCD/TV On Screen Display 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 10 Go to cover page BDL3221 LCD/TV On Screen Display 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 11 Go to cover page BDL3221 LCD/TV On Screen Display 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 12 Go to cover page BDL3221 LCD/TV On Screen Display 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 13 Go to cover page BDL3221 LCD/TV Circuit Description This LCD TV monitor use BDS platform for the video and audio processing. It can support PC analog, digital signal and TV signal. It support PIP function that is TV picture on PC graphic or TV picture on DVI (support HDCP). It's output resolution is up to 1366X768 75Hz for WXGA panel. It can support DVI HDCP digital signal input and also support TV (RF) , CVBS/ RG B signal ( from SCART1 I/O) , YPbPr ( from Cinch I/O for SDTV and HDTV) , CVBS/YC ( Audio shared ) , It has one headphone output. The Y Pb Pr signal input (from Cinch I/O) support 480I, 480P, 720P, 1080i 60Hz and 576I, 576P, 720P, 1080I 50Hz HDTV input. It also have PVR output function , support and monitor all the CVBS signal output with L/R sound. This LCD monitor TV use MST5151A as Scaler engine, which has embedded Analog D-sub, digital DVI(HDMI) decoder, scaling input signal for panel, OSD and advanced 3D de-interlace. The DDR SDRAM is used to accomplish video frame rate conversion and PIP function. The external CPU is used for back light control, RC receiver, keypad input, I/O switch control , IIC communication and TV tuning control, MSP3450G sound decoder control, SAA7119 video decoder control , Columbus IC ( 3D -comb filter ) control , and Audio AMP TPA3008D2 control. Video decoder SAA7119 is used for TV video processing and convert it with CCIR 656/8bits digital format and send to Columbus IC for 3D comb filter processing and noise reduction processing , after that then send to Scaler for de-interlace process. Columbus IC is a combination of Enhanced 2D / 3D Comb filter for both PAL and NTSC , and a Spatial / Temporal noise reduction system for both colour and luminance signals . One audio decoder MSP3450G is used for TV sound processing, and output to Class D audio amplifier TPA3008D (2 X10W) audio output. This audio decoder is a global sound decoder for Nafta AP, China and European market. In NAFTA model CC,V-chip data is decoded in SAA5264PS/M3/1437 and the display the CC information via mixed at SAA7119 with the input signal. The V-Chip is decode by SAA5264PS/M3/1437 and control via the MCU. In Europe model "Teletext display". Data decode is done by SAA5264PS/M3/1437, output RGB/FB is to video decoder input for text overlapping. 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 14 Go to cover page BDL3221 LCD/TV Lock/Unlock,Aging,Factory Mode To Lock/Unlock OSD FUNCTION(User Mode) The OSD function can be locked by pressing"MENU"button(1) for more than 15 seconds, the screen shows following windows for 3 seconds.Everytime when you press"MENU" button, this message appears on the screen automatically. Unlock OSD function Unlocked OSD function can be released by pressing "MENU" button for more than 15 seconds again. After 50 seconds, bring up: ---------- ---------- repeatly Connect Signal cable again=> go back to normal display After 50 seconds, bring up: After 5 seconds, bring up: Factory Mode indicator Factory Menu Cursor can move on gray color area Hot key function: by pressing " " and " " key Simultaneously at User Mode (or Factory Mode) (PS: The Offset R G B function can be used on reduce or eliminate snowy noise on the background when the resolution of video signal is 1280*768 vertical 75Hz. Slightly increase or decrease the value until snowy noise completely disappear. AGING... AGING... Side View (Left) ATTENTION OSD MAIN MENU LOCKED ATTENTION OSD MAIN MENU UNLOCKED AGING... Access Aging Mode Step 1 : D Step 2 : untill comes out " AGING screen"] => then release all buttons. Bring up: isconnect Interface Cable between Monitor and PC. Turn off LCD monitor.Then press power " " button.Then quickly push " "and " ",and hold this two buttons Access Factory Mode 1). Turn off monitor. 2). 3). Press "MENU" button, wait until the OSD menu with Characters "BDS 32*420WN6 EU V0.50.3 05051LC32*A 6K3*A1" (below OSD menu) come on the Screen of the monitor. Press power " " button.Then quickly push " " and " ",and hold this two buttons , then the screen comes out "Waiting For Automatic Adjustment ",then the screen will be black for one second untill comes out "Windows screen"] => then release this two buttons. 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 15 Go to cover page BDL3221 LCD/TV Philips Pixel Defect Policy Philips' Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and practice stringent quality control. However, pixel or sub pixel defects on the TFT LCD panels used in flat panel monitors are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees that any monitor with an unacceptable number of defects will be repaired or replaced under warranty. This notice explains the different types of pixel defects and defines acceptable defect levels for each type. In order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT LCD panel must exceed these acceptable levels. For example, no more than 0.0004% of the sub pixels on a 15" XGA monitor may be defective. Furthermore, Philips sets even higher quality standards for certain types or combinations of pixel defects that are more noticeable than others. This policy is valid worldwide. Pixels and Sub pixels A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue. Many pixels together form an image. When all sub pixels of a pixel are lit, the three colored sub pixels together appear as a single white pixel. When all are dark, the three colored sub pixels together appear as a single black pixel. Other combinations of lit and dark sub pixels appear as single pixels of other colors. Types of Pixel Defects Pixel and sub pixel defects appear on the screen in different ways. There are two categories of pixel defects and several types of sub pixel defects within each category. Bright dot defects appear as pixels or sub pixels that are always lit or 'on'. These are the types of bright dot defects: One lit red, green or blue sub pixel Two adjacent lit sub pixels: - Red + Blue = Purple - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) Three adjacent lit sub pixels (one white pixel) Black Dot Defects Black dot defects appear as pixels or sub pixels that are always dark or 'off'. These are the types of black dot defects: One dark sub pixel Two or three adjacent dark sub pixels Proximity of Pixel Defects Because pixel and sub pixels defects of the same type that are near to one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have pixel or sub pixel defects exceeding the tolerances listed in the following tables. Note: * 1 or 2 adjacent sub pixel defects = 1 dot defect All Philips monitors are ISO13406-2 Compliant * Bright Dot is defined as dots (sub-pixels) which appeared brightly in the screen when the LCM displayed with whole pattern & Bright Dot's brightess is defined over 50% of the brightness against around. (but, Green bright dot is over 30% of brightness against around) * Here in Tiny Bright Dot is defined as "for Red and Blue" the bright area should be no longer than 1/2 sub-pixel and for green the bright area should be no larger than 1/3 sub-pixel. 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 16 Go to cover page BDL3221 LCD/TV Mechanical Instruction Front view Back view Step 1. Remove the tands. a. Remove the sound boxs. Unscrew the 4 screws as Fig.3 sound boxs and s Fig.3 Fig.2 Fig.1 Step 2: Remove the Back Cover Assy a. Unscrew 20 screws as shown in Fig.6. b. Unscrew 8 screws as shown in Fig.7. c. Unscrew 9 screws as shown in Fig.8. d. Remove the and BACK COVER ASSY in Fig.9. Step 3. Remove the Scaler ,IR and Power board. a. Unscrew the 12 screws and disconnect the 9 cables as Fig.9 and Fig.10. b. Remove the Scaler ,IR and Power board as Fig. 11. b. Remove the stands. Unscrew the 6 screws as Fig.4 and Fig.5 . Fig.4 Fig.5 Fig.6 Fig.7 Fig.8 Fig.9 Fig.10 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 17 Go to cover page BDL3221 LCD/TV Mechanical Instruction In warranty, it is not allowed to disassembly the LCD panel, even the backlight unit defect. Out of warranty, the replacment of backlight unit is a correct way when the defect is cused by backlight (CCFL,Lamp). Fig. 11 Step 4. Remove the LCD panel. a. Unscrew b. Remove the as Fig.12. c. Remove FRONT BEZEL ASSY(B) as Fig.13. BOTTOM MAIN FRAME the 4 screws and disconnect the 2 cables as Fig. 11. LCD Panel 1050 823827717361 LCD LC320W01-A6K1. Fig. 12 Fig. 13 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 18 Go to cover page BDL3221 LCD/TV Color Adjustment Alignment procedure 1. Turn on the LCD monitor. 2.Turn on the Timing/pattern generator. See Fig.1 3. Preset LCD color Analyzer CA-110 -Remove the lens protective cover of probe CA-A30. -Set measuring/viewing selector to measuring position for reset analyzer.(zero calibration) as Fig.2 - Turn on the color analyzer (CA-110) -Press 0-CAL button to starting reset analyzer. Fig. 1 Fig. 2 Clear image Clear image Measurement/viewing selector Measurement/viewing selector Fig. 3 4). Press button, then select factory mode indicator by "MENU" " " button .Press"MENU" button to bring up submenu windows as below: Fig.5 Cover (black) Cover (black) Measurement viewing selector Measurement viewing selector Fig. 4 Fig. 2 Factory Mode indicator 5.1 Auto color adjustment (B) Apply a 1360x768/60Hz signal with 32-gray levels pattern, Set smart picture at "Normal" , and Brightness to 50% and Contrast to 50%. Set AUTO-COLOR function for auto ADC offset and gain setup. Adjust the R. G. B offset, and gain to calibrate the color smoothly and 32-gray level distinguishable. Check all factory pre- setting modes. 5.2 Adjustment of WHITE-D (B) Apply a 1360*768 / 60Hz signal with white pattern, set brightness control at 50%, and contrast control at 50%. Adjust the R, G, B Sub- Gain, for he screen center, the 1931 CIE chromaticity (X, Y) co- ordinates shall be; Note: 1. Use Minolta CA-110 for color coordinates and luminance check. 2.Set Light Senor off before W-D adjustment. 3. Luminance> 400 cd/m2 in the center of the screen at 6500(NORAML) color and PC Brightness control; Contrast control at 100% 4.Set smart picture at normal ,brightness &contrast to 50% after alignment. 5.Set Light senor off after Light senor check. 9300�K 6500�K x (center) 0.283 � 0.005 0.313 � 0.005 y (center) 0.297 � 0.005 0.329 � 0.005 4. Access Factory Mode 1). Turn off monitor. 2). 3). Press "MENU" button, wait until the OSD menu with Characters "BDS 32*420WN6 EU V0.50.3 05051LC32*A 6K3*A1" (below OSD menu) come on the Screen of the monitor. Press power " " button.Then quickly push " " and " ",and hold this two buttons , then the screen comes out "Waiting For Automatic Adjustment ",then the screen will be black for one second untill comes out "Windows screen"] => then release this two buttons. 5.Display Press " " or " " button to select . Change the value by " " or " " key until the X,Y co-ordinates as below 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 19 Go to cover page BDL3221 LCD/TV Warning Message Read and follow these instructions when connecting and using your computer monitor: Keep the monitor out of direct sunlight and away from stoves or any other heat source. Remove any object that could fall into ventilation holes or prevent proper cooling of the monitor's electronics. Do not block the ventilation holes on the cabinet. When positioning the monitor, make sure the power plug and outlet are easily accessible. If turning off the monitor by detaching the power cable or DC power cord, wait for 6 seconds before attaching the power cable or DC power cord for normal operation. Please use approved power cord provided by Philips all the time. If your power cord is missing, please contact with your local service center. (Please refer to Customer Care Consumer Information Center) Do not subject the LCD monitor to severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation. To protect your display from possible damage, do not put excessive pressure on the LCD panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by placing your hand or fingers on the LCD panel. Unplug the monitor if you are not going to use it for an extensive period of time. Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off. However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your monitor. To avoid the risk of shock or permanent damage to the set, do not expose the monitor to dust, rain, water, or excessive moisture environment. If your monitor gets wet, wipe it with dry cloth as soon as possible. If foreign substance or water gets in your monitor, please turn the power off immediately and disconnect the power cord. Then, remove the foreign substance or water, and send it to the maintenance center. Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or extreme cold. In order to maintain the best performance of your monitor and use it for a longer ligetime, please use the monitor in a location that falls within the following temperature and humidity ranges. Temperature: 5-40 C 41-104 F Humidity: 20-80% RH The casing cover should be opened only by qualified service personnel. If there is any need for any document for repair or integration, please contact with your local service center. (please refer to the chapter of "Consumer Information Center") For transportation information, please refer to "Physical Specifications". Do not leave your monitor in a car/trunk under direct sun light. Operation: Maintenance: Service: � � � � � � � � � � � � � � � � � � � � O O 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 20 Go to cover page BDL3221 LCD/TV Troubleshooting This page deals with problems that can be corrected by the user. If the problem still persists after you have tried these solutions, contact your nearest Philips dealer. Common Problems Symptoms Having this problem? No Video/ Power LED off � � � Check connection integrity at both ends of the video cable and/or power cord. Electric outlet verification Ensure AC power at the rear of the monitor TV is switched on. No Video/ Power LED on � � � Increase brightness and contrast controls. Perform the LCD Monitor TV self-test feature check. Check for bent or broken pins in video cable connector. � � � � � Auto adjust image through Menu -> Image Setting -> Auto Adjust. Adjust Phase and Clock controls via OSD. Eliminate video extension cables. Perform the LCD Monitor TV factory reset (via Menu -> Factory Reset -> All Settings). Lower video resolution or increase font size. Shaky/Jittery Video � � � � � Auto adjust image through Menu -> Image Setting -> Auto Adjust Adjust Phase and Clock controls via OSD Perform the LCD Monitor TV factory reset (via Menu -> Factory Reset -> All Settings) Check environmental factors Relocate and test in other room Missing Pixels Stuck-on Pixels � � Cycle power on-off These are pixels that are permanently on and is a natural defect that occurs in LCD technology Brightness Problems � � � Perform the LCD Monitor TV factory reset (via Menu -> Factory Reset -> All Settings) Auto adjust image through Menu -> Image Setting -> Auto Adjust Adjust brightness & contrast controls Geometric Distortion � � � � Perform the LCD Monitor TV reset on "Position Settings Only" Auto adjust image through Menu -> Image Setting -> Auto Adjust Adjust the centering controls Ensure the LCD Monitor TV is in proper video mode Horizontal/Vertical Lines � � � � � Perform the LCD Monitor TV reset Auto adjust image through Menu -> Image Setting -> Auto Adjust Adjust Phase and Clock controls via OSD Perform the LCD Monitor TV self-test feature check and determine if these lines are also in self-test mode Check for bent or broken pins in the video cable connector Sync Problems � � � � � � Perform the LCD Monitor TV reset Push Auto Adjust button Adjust Phase and Clock controls via OSD Perform the LCD Monitor TV self-test feature check to determine if scrambled screen appears in self-test mode Check for bent or broken pins Boot up in the "safe mode" LCD Scratched � Turn the LCD Monitor TV off and clean the screen Safety Related Issues � � Do not perform any troubleshooting steps The LCD Monitor TV needs to be replaced Intermittent Problems � � � � Ensure the LCD Monitor TV is in proper video mode Ensure video cable connection between computer and the LCD monitor TV is secured Perform the LCD Monitor TV factory reset (via Menu -> Factory Reset -> All Settings) Perform the LCD Monitor TV self-test feature check to determine if the intermittent problem occurs in self-test mode Check these items No picture, the LCD Monitor TV is not working No picture or no brightness Poor Focus Picture is fuzzy, blurry or ghosting Wavy picture or fine movement LCD screen has spots � � Cycle power on-off These are pixels that are permanently off and is a natural defect that occurs in LCD technology LCD screen has bright spots Picture too dim or too bright Note: When operating in DVI mode, the contrast adjustment is not available. Screen not centered correctly Note: When operating in DVI mode, the positioning adjustments are not available. Screen has one or more lines Note: When operating in DVI mode, the Pixel Clock and Phase adjustments are not available. Screen is scrambled or appears torn Screen has scratches or smudges Visible signs of smoke or sparks The LCD Monitor TV malfunctions on & off 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 21 Go to cover page BDL3221 LCD/TV Troubleshooting TV and Audio Problems Poor TV signal reception Abnormal picture seen from the screen No TV picture � Have you connected the aerial socket properly? Have you chosen the right system? Poorly connected SCART cables or aerial sockets are often the cause of picture or sound problems (sometimes the connectors can become half disconnected if the LCD Monitor TV set is moved or turned). Check all connections. Video Problems � � Check Video Input Selection Composite: Yellow colored RCA jack S-Video: Typically a round 4 pin jack Component: Typically 3 RCA jacks of Green, Red and Blue. Make sure you did not plug the video cable to video output port behind the LCD monitor TV. Low Quality DVD playback Stuck-on Pixels No sound � � � � Check if the LCD Monitor TV volume is turn off of muted. Connect the audio cable securely. Audio cable is connected incorrectly. Verify that the audio source is selected correctly in the OSD. Remote Control Problems � � � Point the remote control directly at the remote sensor on the LCD Monitor TV. Replace both batteries with new ones. Make sure the remote control is not disabled (for disable/enable the remote control, please refer to the section of Remote Control). Product Specific Problems � The proximity of mountains or high buildings may be responsible for ghost pictures, echoing or shadows. In this case, try manually adjusting your pictures: see 'fine tuning' or adjust the direction of the outside aerial. For Asia users in non-NTSC area: Does your antenna enable you to receive broadcasts in this frequency range (UHF or VHF band)? In the event of difficult reception (snowy pictures) switch the NR on the PICTURE menu to ON. No picture when TV input was selected No sound No sound output when a program with sound was playing No signal indicator is displayed. Picture not crisp and some color distortion LCD screen has bright spots See video but no audio No response from the LCD Monitor TV when remote is pressed Image is centered on screen, but does not fill entire viewing area � � Ensure that the audio cables are firmly connected to both the audio input connectors on your the LCD Monitor TV and audio output connectors on your PC or Video player. If on certain TV channels you receive a picture but no sound, this means that you do not have the correct TV system. Modify the SYSTEM setting. No Video � Check DVD connection Composite gives good picture S-Video gives better picture Component gives best picture Remote control does not work properly Screen image is too small � Perform the LCD Monitor TV factory reset (via Menu -> Factory Reset -> All Settings). For further assistance, refer to the Consumer Information Centers list and contact your local Philips distributor. OSD Warning Messages A warning message may appear on the screen indicating the LCD Monitor TV current status. When user sees this warning message, it means that the LCD Monitor TV is in adjustment process. A warning message may appear on the screen indicating that the LCD Monitor TV is out of sync range. See Specifications for the Horizontal and Vertical frequency ranges addressable by this the LCD Monitor TV. Recommended mode is 1360 x 768 @ 60Hz. This message means that there is no video input signal. The LCD Monitor TV is in a power saving mode (in PC mode). The main OSD menu is unlocked. The main OSD menu is locked. 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 22 Go to cover page BDL3221 LCD/TV Electrical Instructions 1. General points 1.1 During the test and measuring, supply a distortion free AC mains voltage to the apparatus via an isolated transformer with low internal resistance. 1.2 All measurements mentioned hereafter are carried out at a normal mains voltage (90 - 142 VAC for NAFTA version, 195 -264 VAC for EUROPEAN version, or 90 - 264 VAC for the model with full range power supply, unless otherwise stated.) 1.3 All voltages are to be measurement or applied with respect to ground,unless otherwise stated. 1.4 The test has to be done on a complete set including LCD panel in a room with temperature of 25 +/- 5 degree C. 1.5 All values mentioned in these test instruction are only applicable of a well aligned apparatus, with correct signal. 1.6 The letters symbols (B) and (S) placed behind the test instruction denotes (B): carried out 100% inspection at assembly line (S): carried out test by sampling 1.7 The white balance (color temperature), has to be tested in subdued lighted room. 1.8 Repetitive power on/off cycle are allowed except it should be avoided within 6 sec. 2. Input and output signal 2.1.1 PC Signal type a. Analog Video : 15 pin D-sub ,0.7 Vp-p linear, positive polarity&separate sync.( TTL level, positive or negative polarity) b. Digital Video : DVI-Digital interface with 4 channels TMDS signal c. Audio signal : 3.5mm stereo mini-jack Level: - Nominal : 0.5 V rms. - Maximum : 1.5 V rms. - Impedance > 10 k �. d.Signal source: Pattern generator format as attachment table 1 to 12.Reference generator : CHROMA 2200 or 2250 2.1.2 TV Signal type(Video Model: w/o RF signal input) RF Signal : Aerial input / 10mV(80dBuV) Video signal : CVBS input ( RCA jack) / 1Vpp (300mV-sync, 700mV-video.) S video input / 1VppY-signal, 300mVpp C-signal SCARTx1: CVBS, RGB signal HD in(YPbPr input)/ 1Vpp Y signal, 350mVpp Pb,Pr signal HDCP:Digital interface with 4 channels TMDS signal Audio signal : Audio (1) R/L for AV IN(AV and S-Video). Level: - Nominal : 0.5 V rms. - Maximum : 1.5 V rms. - Impedance > 10 k �. Audio (2) R/L for SCART IN Level: - Nominal : 0.5 V rms. - Maximum : 1.5 V rms. - Impedance > 10 k �. Audio (3) R/L for HD Video IN. Level: - Nominal : 0.5 V rms. - Maximum : 1.5 V rms. - Impedance > 10 k�. 2.1.3 CVBS output: Video: CVBS output 1Vpp / Impedance : 75 �. Audio: R/L output (from CVBS) Level: - Nominal : 0.5 V rms. - Maximum : 1.5 V rms. - Impedance < 1 k �. 2.1.4 Headphone Audio: R/L output -10mW at 32 �. 3.5mm stereo jack with switch Impedance is between 8 and 600 ? . 2.2 PC Input signal mode 2.2.1 PRESET VIDEO RESOLUTION The analogue color LCD monitor must be capable of displaying standard resolutions within the vertical frequency range of 50 � 75 Hz, and horizontal scan range of 30 - 63 KHz . Use the CHROMA-2250 generator as the standard signal timing source. Dot rate (MHz) H.freq (KHz) Mode Resolution V.freq (Hz) Remark 1 25.175 31.469 VGA-1 640*350 70.086 2 25.175 31.469 IBM VGA 640 * 480 59.940 3 31.500 37.500 VGA 640 * 480 75.000 4 28.322 31.469 VGA 720*400 70.087 5 36.000 35.156 VESA 800 * 600 56.250 6 40.000 37.879 VESA 800 * 600 60.317 7 49.500 46.875 VESA 800 * 600 75.000 8 65.000 48.363 VESA 1024 * 768 60.004 9 78.750 60.023 VESA 1024 * 768 75.029 10 74.500 47.772 WXGA 1280 * 720 59.855 CVT 11 79.500 47.776 WXGA 1280 * 768 59.870 CVT 12 84.75 47.720 VSEA 1360 * 768 59.799 CVT Resolution recommend on 1360x768 @ 60Hz Remark:Mode 1,3,4,5,7,9,11 will run auto adjustment only, and W/O QA checking 2.3.1 Table 2.3.1 for NAFTA model Signal Distribution Table (NTSC) Frequency Carriers CH Video Sound TV System Pattern A 03 61.25MHz 65.75MHz NTSC M Color Circle A 06 83.25MHz 87.75MHz NTSC M Red Raster A 09 187.25MHz 191.75MHz NTSC M Circle Pattern A 11 199.25MHz 203.75MHz NTSC M Cross Hatch A 13 211.25MHz 215.75MHz NTSC M Two White Window A 52 699.25MHz 703.75MHz NTSC M Color Bar A 69 801.25MHz 805.75MHz NTSC M 100% White C 70 499.25MHz 503.75MHz NTSC M Checkerboard Table 2.3.1 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 23 Go to cover page BDL3221 LCD/TV Electrical Instructions 2.3.2 Table 2.3.2 for WE model Signal Distribution Table ( PAL ) Frequency Carriers PRG CH Video Sound TV System Pattern 0 1 AU37 590.25MHz 595.75MHz PAL B(UK) Pure White 2 AU2 64.25MHz 69.75MHz PAL B(UK) Circle Pattern 3 E7 189.25MHz 194.75MHz PAL B(CCIR) Circle Pattern 4 G47 679.25MHz 684.75MHz PAL G(CCIR) Circle Pattern 5 I23 487.25MHz 493.75MHz PAL I(UK) Circle Pattern 6 E12 224.25MHz 229.75MHz PAL B(CCIR) Color Bar 7 AU7 182.25MHz 187.75MHz PAL B(UK) Color Bar 8 G68 847.25MHz 852.75MHz PAL G(CCIR) 100% White 9 AU9 196.25MHz 201.75MHz PAL B(UK) Checkerboard 10 AU10 209.25 MHz 214.75 MHz PAL B(UK) Crosshatch 11 AU0 46.25MHz 51.75MHz PAL B(UK) Color Bar 12 AU2 64.25MHz 69.75MHz PAL B(UK) Color Bar 13 AU5 102.25 MHz 107.75 MHz PAL B(UK) Crosshatch 14 AU5A 138.25MHz 143.75MHz PAL B(UK) Color Bar 15 AU7 182.25MHz 187.75MHz PAL B(UK) Pure White 16 AU9 196.25MHz 201.75MHz PAL B(UK) Pure White 17 AU10 209.25MHz 214.75MHz PAL B(UK) Circle Pattern 18 I23 487.25MHz 493.75MHz PAL I(UK) Circle Pattern 19 G28 527.25MHz 532.75MHz PAL G(CCIR) Circle Pattern 20 AU37 590.25MHz 595.75MHz PAL G (UK) Circle Pattern 21 I40 623.25MHz 629.75MHz PAL I(UK) Color Bar 22 CH44 655.25MHz 661.75MHz PAL DK(UK) Color Bar 23 I60 783.25MHz 789.75MHz PAL I(UK) 100% White 24 I66 831.25MHz 837.75MHz PAL I(UK) Checkerboard 25 K21 471.25 MHz 477.75 MHz SEC K1(CCIR) Crosshatch 28 G28 527.25MHz 532.75MHz PAL G(UK) Color Bar Table 2.3.2 2.3.3 Table 2.3.3 for AP-Multi model Signal Distribution Table (PAL and NTSC) Frequency Carriers PRG CH Video Sound TV System Pattern 0 1 AU37 590.25MHz 595.75MHz PAL B(UK) Pure White 2 AU2 64.25MHz 69.75MHz PAL B(UK) Circle Pattern 3 E7 189.25MHz 194.75MHz PAL B(CCIR) Circle Pattern 4 G47 679.25MHz 684.75MHz PAL G(CCIR) Circle Pattern 5 I23 487.25MHz 493.75MHz PAL I (UK) Circle Pattern 6 M58 735.25MHz 739.75MHz NTSC M(CCIR) Color Bar 7 AU7 182.25MHz 187.75MHz PAL B(UK) Color Bar 8 K21 471.25MHz 477.75MHz PAL G (CCIR) 100% White 9 AU9 196.25MHz 201.75MHz PAL B(UK) Checkerboard 10 AU10 209.25 MHz 214.75 MHz PAL B(UK) Crosshatch 11 E12 224.25MHz 229.75MHz PAL B(CCIR) Color Bar 12 G34 575.25MHz 580.75MHz PAL G(CCIR) Color Bar 13 G62 799.25 MHz 804.75 MHz PAL G(CCIR) Crosshatch 14 C4 77.25MHz 83.75MHz PAL D(CCIR) Color Bar 28 G28 527.25MHz 532.75MHz PAL G(UK) Color Bar Table 2.3.3 2.3.4 TV Table 2.3.4 for China model Signal Distribution Table (PAL D) Frequency Carriers PRG CH Video Sound TV System Pattern 1 C 4 65.25MHz 71.75MHz PAL D(CCIR) Full Write 2 E 7 184.25MHz 190.75MHz PAL D(CCIR) Circle Pattern 3 E12 224.25MHz 230.75MHz PAL D(CCIR) Color Bar 4 K21 471.25MHz 477.75MHz PAL D (CCIR) Full Write 5 G34 511.25MHz 517.75MHz PAL D(CCIR) Circle Pattern 6 G62 547.25MHz 553.75MHz PAL D(CCIR) Color Bar 7 M58 551.25MHz 557.75MHz PAL D(CCIR) Crosshatch 8 G47 615.25MHz 621.75MHz PAL D(CCIR) Color Bar Table 2.3.4 2.4 HD input mode 2.4.1 HD detail timing (For Quantune Data setting with Q801GD or 802G in YpbPr mode) Item 1920X1080i 60Hz 1280X720P 60Hz 1920X1080i 50Hz 1280X720P 50Hz Pixel rate 74.25MHz (13.468 ns) 74.25MHz (13.468 ns) 74.25MHz ( 13.468ns ) 74.25MHz (13.468 ns) Horizontal Frequency 33.75KHz 45KHz 28.125KHz 37.5KHz Active 1920 pixels (25.859 us) 1280 pixels (17.239 us) 1920 pixels (25.859 us) 1280 pixels (17.239 us) Blank 280 pixels (3.771 us) 370 pixels (4.983 us) 720 pixels ( 9.697 us ) 700 pixels (9.428 us) Period 2200 pixels (29.630 us) 1650 pixels (22.222 us) 2640 pixels (35.556 us ) 1980 pixels (26.667 us) Pulse delay 44 pixels (0.593 us) 70 pixels (0.943 us) 484 pixels ( 6.519 us ) 400 pixels (5.387 us) Pulse width 44 pixels (0.593 us) 40 pixels (0.539 us) 44 pixels ( 0.593 us ) 40 pixels (0.539 us) Vertical Frequency 60 Hz 60 Hz 50 Hz 50 Hz Active 1080 lines (42.000 ms) 720 lines (16.0 ms) 1080 lines ( 38.4 ms ) 720 lines (19.2 ms) Blank 45 lines (1.333 ms) 30 lines (0.667 ms) 45 lines (1.6 ms ) 30 lines (0.8 ms) Period 1125 lines (33.333 ms) 750 lines (16.667 ms) 1125 lines ( 40 ms ) 750 lines (20 ms) Pulse delay 2 lines (0.059 ms) 5 lines (0.111 ms ) 2 lines ( 0.071 ms ) 5 lines (0.133 ms ) Pulse width 5 lines (0.148 ms) 5 lines (0.111 ms) 5 lines (0.178 ms ) 5 lines (0.133 ms) EQ before 0 line 0 line 0 line 0 line EQ after 1 line 0 line 1 line 0 line Scan Interlace Progressive Interlace Progressive Sync type ACS ACS ACS ACS Video kind Analog YPbPr (ITU- R BT.709) Analog YPbPr (ITU- R BT.709) Analog YPbPr (ITU- R BT.709 ) Analog YPbPr (ITU- R BT.709) 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 24 Go to cover page BDL3221 LCD/TV Electrical Instructions Table 2 Item 720X576P 50Hz 720X480P 60Hz 720X576i 50Hz 720X480i 60Hz Pixel rate 27 MHz (37.037 ns) 27.027MHz (37.000 ns) 13.5MHz ( 74.074 ns ) 13.5MHz ( 74.074 ns ) Horizontal Frequency 31.25 KHz 31.5KHz 15.625KHz 15.734KHz Active 720 pixels (26.667 us) 720 pixels (26.640 us) 720 pixels (53.333 us) 720 pixels (53.333 us) Blank 144 pixels (5.333 us) 138 pixels (5.106 us) 144 pixels ( 10.667 us ) 138 pixels ( 10.222 us ) Period 864 pixels (42.000 us) 858 pixels (31.746 us) 864 pixels ( 64.00 us ) 858 pixels ( 63.556 us ) Pulse delay 12 pixels (0.444 us) 16 pixels (0.592 us) 12 pixels ( 0.889 us ) 19 pixels ( 1.407 us ) Pulse width 64 pixels (2.370 us) 62 pixels (2.294 us) 63 pixels ( 4.667 us ) 62 pixels ( 4.593 us ) Vertical Frequency 50 Hz 60 Hz 50 Hz 59.94 Hz Active 576 lines (18.442 ms) 480 lines (15.238 ms) 576 lines ( 36.864 ms ) 480 lines ( 30.507 ms ) Blank 49 lines (1.568 ms ) 45 lines (1.429 ms) 49 lines (3.136 ms ) 45 lines (2.860 ms ) Period 625 lines (20.000 ms) 525 lines (16.667 ms) 625 lines ( 40 ms ) 525 lines ( 33.367 ms ) Pulse delay 5 lines (0.160 ms) 9 lines (0.287 ms) 2 lines ( 0.128 ms ) 4 lines ( 0.254 ms ) Pulse width 5 lines (0.160 ms) 6 lines (0.190 ms) 3 lines (0.192 ms ) 3 lines (0.191 ms ) EQ before 0 line 0 line 2 line 3 line EQ after 0 line 0 line 2 line 3 line Scan Progressive Progressive Interlace Interlace Sync type ACS ACS ACS ACS Video kind Analog YPbPr (SMPTE RP177) Analog YPbPr (SMPTE RP177) Analog YPbPr (SMPTE RP177 ) Analog YPbPr (SMPTE RP177 ) 3. Power supply 3.1 Setup the AC I/P at 264 VAC and 90VAC , and power board provide two DC Output 1.The DC output voltage is 24V � 1V DC for Inverter and Scaler board Measured point between pin3(+24V) and pin6(GND) at item 1001 of scaler board 2.The DC output voltage is 16V � 1 V DC for Scaler and Audio board Measured point between pin1(+16V) and pin6(GND) at item 1001 of scaler board 3.2 Any adjustment is not needed. 4. PC mode Display Adjustment 4.1 Display quality adjustment Use timing mode as describe in 2.2, and use the POPO (pixel on pixel off) pattern to adjust the clock until no stripe and adjust the phase until clear picture. Adjust all pre-load 12 modes, but ignore the wave interference on non-60 Hz modes. 4.2 WHITE-D adjustment (B) 4.2.1 At factory mode apply 1360X768 @60Hz mode with 32 gray pattern. Set smart picture at "Normal" , and Brightness to 50% and Contrast to 50%. Set AUTO-COLOR function for auto ADC offset and gain setup. 4.2.2 Apply full white pattern , adjust the Cool, Normal & Warm SCALER GAIN RG B to reach W/D and luminance in factory mode.(See fig.1) 1. Check (X, Y) co-ordinates as below : Table 4.2.2.1: Reading with Minolta CA-110. 2. Check the gray level color poor & noise condition and chromaticity Note: 1. Use Minolta CA-110 for color coordinates and luminance check. 2.Set Light Senor off before W-D adjustment. 3.Luminance> 400 cd/m2 in the center of the screen at 6500(NORAML)color and PC Brightness control; Contrast control at 100% 4.Set smart picture at normal ,brightness &contrast to 50% after alignment. 5.Set Light senor off after Light senor check. 4.3 Check the digital interface cable (B) Check the 32 gray level color poor & noise condition. Cool/9300�K Normal/6500�K Warm/5700�K x (center) 0.283 � 0.005 0.313 � 0.005 0.328 � 0.005 y (center) 0.297 � 0.005 0.329 � 0.005 0.344 � 0.005 Fig.1 Fig.2 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 25 Go to cover page BDL3221 LCD/TV Electrical Instructions 5. TV Mode display adjust 5.1 White balance adjustment (B) 5.1.1 General set-up : Equipment Requirements: Color analyzer. Input requirements: Input Signal Type : RF signal 1.Set to NTSC system, frequency=187.25MHZ ( for NAFTA model ), with white pattern of 100% 2. Set to PAL B/G system, frequency=64.25MHz ( for WE model ) with white pattern of 100% Input Signal Strength : 10mV (80 dBuV) terminal voltage. Input Injection Point : TV Tuner input Alignment method: Initial Set-up : 1.Set 711X SDTV Brightness=135; Sat. =64, Contrast =50 in Factory mode(can be fine tuned). 2. Set Smart picture as "Personal" 3. Apply "100% Full White" pattern by TV pattern generator. Alignment : Set the VIDEO SCALER GAIN R G B=SCALER GAIN R G B in Factory Mode(See Fig 2.)[ Enter factory menu : press VOL+ and VOL- keys together around six seconds or use factory command by Industrial PC. 1. Check (X, Y) co-ordinates in factory mode as below: Table 5.1.1 Reading with Minolta CA-110. 2.Set TV Color temperature in Factory model as Cool, and check smart picture at "Sports" after factory alignment. 3.Check the gray pattern should be distinguished and color bar is correct. 4.Set TV DCR at ON. 6. HDTV Mode display adjust 6.1 White balance adjustment (B) General set-up: Equipment: Quantum Data Pattern Generator 801GD or 802G. Apply 1080i, RGBW(Infocus2) gray pattern. Or FLUKE 54200, apply 576i(PAL B/G), DIGITAL SCAN/DIGI_ADC1 pattern. Alignment method: Initial Set-up : 1.Set Smart picture as "Personal", Brightness=50, Color=50, Contrast=50) 2.Set AUTO-COLOR function for HDTV ADC offset & gain setup. Cool/9300�K Normal/6500�K Warm/5700�K x (center) 0.283 � 0.015 0.313 � 0.015 0.328 � 0.015 y (center) 0.297 � 0.015 0.329 � 0.015 0.344 � 0.015 Alignments : 1. Apply "100% Full White" pattern by Quantum DATA 802G pattern generator. Check (X, Y) co-ordinates as below: Picture Mode x y Personal 0.283 � 0.015 0.298 � 0.015 If chromaticity (X, Y) co-ordinates is out of specification, re-alignment Video scalar R/G/B gain from 127/127/127. 2. Set smart picture at sports after HDTV alignment. 3.Check the gray pattern should be distinguished and color bar is correct 7. Preset DVI HDCP Key 7.1 Download HDCP Key The 284 bytes HDCP key should be download to the set via I/F cable using ATE at factory Alignment tools 7.2 DVI Video HDCP Key Test 7.2.1 Use pattern generator Equipment: Quantum 802R or 802BT or equivalent equipments. Pattern : Standard HDCP Pattern (It’s color bar) Timing : 720 X 480P 60Hz 720 X 576P 50Hz 1280X 720P 50Hz 1280X 720P 60Hz 1920X1080i 50Hz 1920X1080i 60Hz Result : The PASS information should be shown on the screen. 7.2.2 Use DVD Player: Equipment: 1.Pioneer (model: DV-S969AVi) or equivalent equipments. 2.DVD disk with " Macro Vision " protection. Result : The picture should be shown Normally. 8. Preset EEPROM data EEPROM data has to be preset data according following table. 8.1 Factory mode preset. Function Preset value SCALER GAIN 127 127 127 ADC Offset R/G/B 127 127 127 ADC Gain R/G/B 127 127 127 PC OFFset R/G/B 127 127 127 7119 ? brightness #1 7119 Saturation #1 7119 contrast #1 7119 TINT #1 #2 #2 DVI SHIFT H DVI SHIFT V #2 #2 NTSC PAL 171 193 TV shift H TV shift V Regular 11 2 #3 #3 HD SHIFT H HD SHIFT V #3 #3 HD ADC OFFset R G B 127 127 127 HD ADC GAIN R G B 127 127 127 Video Scaler Gain 127 127 127 Scaler Hue 50 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 26 Go to cover page BDL3221 LCD/TV Electrical Instructions #1 PERSONAL/ COOL ? SAT. TINT PAL 135 64 50 24 NTSC 127 64 64 24 TV SECAM 111 64 77 24 PAL 140 64 56 24 NTSC 132 64 64 24 AV SECAM 111 64 77 24 PAL 137 64 54 24 NTSC 134 64 64 24 S-Video SECAM 113 64 77 24 PAL 136 64 62 24 NTSC 138 64 55 24 EXT SECAM 115 64 77 24 8.2 Smart picture & Smart sound: 8.2.1 Final TV mode out box setting. Smart Picture : Sports Color Temp in Factory mode : COOL Notice : These setting only could modify in factory mode for user , excluding "Personal" , these menus should be blanking. Smart Sound : Personal SOUND VOLUME : 25 BASE : 50 TREBLE : 50 Balance :0 Virtual SURROUND : OFF AVL : Yes #2 #3 480P 576P 720P/ 50Hz 720P/ 60Hz 1080i/ 50Hz 1080i/ 60Hz DVI shift H(HDCP) 22 22 96 54 103 48 DVI shift V(HDCP) 45 50 43 42 61 62 480i 480P 576i 576P 720P/ 50Hz 720P/ 60Hz 1080i/ 50Hz 1080i/ 60Hz HD shift H 152 153 164 163 105 144 77 75 HD shift V 39 40 52 53 39 38 58 59 PERSONAL BRIGHTNESS 50 COLOR 50 CONTRAST 50 SHARPNESS 51 TINT 50 BRIGHTNESS 60 COLOR 49 CONTRAST 58 SHARPNESS 64 MOVIES TINT 50 SPORTS BRIGHTNESS 50 COLOR 55 CONTRAST 63 SHARPNESS 64 TINT 50 BRIGHTNESS 60 COLOR 45 CONTRAST 50 SHARPNESS 58 WEAK SIGNAL TINT 50 MULTIMEDIA BRIGHTNESS 38 COLOR 55 CONTRAST 55 SHARPNESS 64 TINT 50 BRIGHTNESS 50 COLOR 50 CONTRAST 50 SHARPNESS 51 NIGHT TINT 50 PERSONAL EQ BAND1 120Hz +0 EQ BAND2 500Hz +0 EQ BAND3 1.5KHz +0 EQ BAND4 5KHz +0 EQ BAND5 10KHz +0 EQ BAND1 120Hz -30 EQ BAND2 500Hz 0 EQ BAND3 1.5KHz +20 EQ BAND4 5KHz +0 NEWS EQ BAND5 10KHz -30 MUSIC EQ BAND1 120Hz +30 EQ BAND2 500Hz +10 EQ BAND3 1.5KHz -20 EQ BAND4 5KHz +10 EQ BAND5 10KHz +30 EQ BAND1 120Hz +45 EQ BAND2 500Hz +0 EQ BAND3 1.5KHz -20 EQ BAND4 5KHz +10 THEATRE EQ BAND5 10KHz +40 Smart Sound EQ Setting Smart Picture 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 27 Go to cover page BDL3221 LCD/TV Pin No. Description 1 T.M.D.S. data2- 2 T.M.D.S. data2+ 3 T.M.D.S. data2 shield 4 No Connect 5 No Connect 6 DDC clock 7 DDC data 8 No Connect 9 T.M.D.S. data1- 10 T.M.D.S. data1+ 11 T.M.D.S. data1 shield 12 No Connect 13 No Connect 14 +5V Power 15 Ground (for +5V) - Cable detect 16 Hot plug detect 17 T.M.D.S. data0- 18 T.M.D.S. data0+ 19 T.M.D.S. data0 shield 20 No Connect 21 No Connect 22 T.M.D.S clock shield 23 T.M.D.S. clock+ 24 T.M.D.S. clock- General DDC Data Re-programming In case the DDC data memory IC or main EEPROM which storage all factory settings were replaced due to a defect, the serial numbers have to be re-programmed "Analog DDC IC, Digital DDC IC & EEPROM". It is advised to re-soldered DDC IC and main EEPROM from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed. Additional information Additional information about DDC (Display Data Channel) may be obtained from Video Electronics Standards Association (VESA). Extended Display Identification Data(EDID) information may be also obtained from VESA. 1. An i486 (or above) personal computer or compatible. 2. Microsoft operation system Windows 95/98 . Y o Install the EDID_PORT_Tool under Win2000/XP . As Fig. 1 . A. Cody the "UserPort.sys" to C:\WINNT\system32\drivers(win2000) C:\WINDOWS\system32\drivers(winXP) B. Running " io.exe" everytime, Before you start to programming edid data . 4. A/D Alignment kits (12NC: 3138 106 10396): inclusion : a. Alignment box x1 (Fig. 2) b. Printer cable x1 c. (D-Sub) to (D-Sub) cable x1 D. (D-Sub) to (DVI) cable x1 System and equipment requirements ou have t 3. EDID46.EXE program Fig. 1 Fig. 1 Fig. 2 To Monitor D-sub/DVI cable DC 8~12V To Printer port Power indicator Note: The alignment box has already build-in a batteries socket for using batteries (8~12V) as power source. Pull out the socket by remove four screws at the rear of box. Please do not forget that remove batteries after programming. The energy of batteries can only drive circuits for a short period of time. PIN No. SIGNAL 1 Red video input 2 Green video input / sync on green 3 Blue video input 4 GND 5 GND - Cable detect 6 Red video GND 7 Green video GND 8 Blue video GND 9 DDC +3.3V or +5V 10 Logic GND 11 GND 12 Serial data line (SDA) 13 H-sync / H+V 14 V-sync 15 Data clock line (SCL) Pin assignment A. 15-pin D-Sub Connector B. Input DVI -D Connector pin Fig. 3 DDC Instructions 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 28 Go to cover page BDL3221 LCD/TV Step 3: Installation of EDID46.EXE Method 1: Start on DDC program Start Microsoft Windows. 1. The Program"EDID46.EXE" in service manual cd-rom be copyed to C:\ . 2. Click , choose Run at start menu of Windows as shown In Fig. 5. Fig. 5 4. Click OK button. The main menu appears (as shown in Fig. 7). This is for initialize alignment box. Fig. 7 Fig. 6 3. At the submenu, type the letter of your computer's hard disk drive followed by :EDID46 (for example, C:\EDID46, as shown in Fig. 6). Note 2: During the loading, EDID46 will verify the EDID data which just loaded from monitor before proceed any further function, once the data structure of EDID can not be recognized, the following error message will appear on the screen as below. Please confirm following steps to avoid this message. 1. The data structure of EDID was incorrect. 2. DDC IC that you are trying to load data is empty. 3. Wrong communication channel has set at configuration setup windows. 4. Cables loosed or poor contact of connection. 1 Fig. 8 Note 1: If the connection is improper, you will see the following error message (as shown in Fig. 8) before entering the main menu. Meanwhile, the (read EDID) function will be disable. At this time, please make sure all cables are connected correctly and fixedly, and the procedure has been performed properly. Fig. 9 Configuration and procedure There is no Hardware DDC (DDC IC) anymore. Main EEPROM stores all factory settings and DDC data (EDID code) which is also called Software DDC. The following section describes the connection and procedure for Software DDC application. The main EEPROM can be re- programmed by enabling '' factory memory data write'' function on the DDC program (EDID46.EXE). Initialize alignment box In order to avoid that monitor entering power saving mode due to sync will cut off by alignment box, it is necessary to initialize alignment box before running programming software (EDID46.EXE). Following steps show you the procedures and connection. Step 1: Supply 8-12V DC power source to the Alignment box by plugging a DC power cord . Step 2: Connecting printer cable and D-Sub cable of monitor as Fig. 4 Fig. 4 PC 1=Power connector 2=D-SUB connector To printer port (LTP1) DC Power 8-12 V Printer Port To Monitor To PC 1 2 -----> -----> DDC Instructions 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 29 Go to cover page BDL3221 LCD/TV DDC Instructions Step 3: Modify DDC data (verify EDID version, week, year) Click (new function) icon from the tool bar, bring up Step 1 of 9 as shown in Fig. 14 . EDID46 DDC application provides the function selection and Step 4: Modify DDC data (Monitor Serial No.) 1. Click Next , bring up Fig. 15. 3. Click OK button to confirm your selection. 4. Click icon (Read EDID function) to read DDC EDID data from monitor. The EDID codes will display on screen as shown in Fig. 13. Fig. 15 2. Select the DDC2Bi as the communication channel. As shown in Fig. 12. Fig. 12 Fig. 13 Fig. 14 Select and fill out, If necessary. Re-programming Analog DDC IC Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 10. Step 2: Read DDC data from monitor 1. Click icon as shown in Fig. 11 from the tool bar to bring up the Channels "Configuration Setup" windows as shown in Fig. 11. Fig. 10 1=Power connector 2=D-SUB connector PC To printer port (LTP1) DC Power 8-12V Printer Port To Monitor To PC 1 2 -----> -----> To PC Video port (D-sub) Click this button =====> Fig. 11 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 30 Go to cover page BDL3221 LCD/TV DDC Instructions Fig. 21 Fig. 18 Fig. 19 7. Click Next , bring up Fig. 21. 4. Click Next , bring up Fig.18. 5. Click Next , bring up Fig.19. 6. Click Next , bring up Fig. 20. In this step, please confirm the Descriptor Data Type is Monitor Range Limits, and all the items are same as below. Fig. 20 2. Click Next , bring up Fig.16. Fig. 16 Fig. 17 3. Click Next , bring up Fig.17. 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 31 Go to cover page BDL3221 LCD/TV DDC Instructions 4). Click (Write EDID) icon from the tool bar to write DDC data. Then wait for a few minutes,DDC data will be finished Writing. Fig. 24 4) Push Menu to exit OSD menu. " " Fig. 22 8. Click Next , bring up Fig. 22. - Click Finish to exit the Step window. - Serial number can be filled up at this moment (for example, 123457). NOTE: You must modify the Serial NO. In step 9, otherwise the Serial NO. In OSD Couldn't be modified correctly. Step 5: Write DDC data 1. Configuration should be as Fig. 23. And press OK. Fig. 23 2. Click Save. Step 7: Exit DDC program Pull down the File menu and select Exit as shown in Fig. 26. Step 6: Save DDC data Sometimes, you may need to save DDC data as a text file for using in other IC chip. To save DDC data, follow the steps below: 1. Click (Save) icon (or click "file"-> "save as") from the tool bar and give a file name as shown in Fig. 25. The file type is EDID46 file (*.ddc) which can be open in WordPad. By using WordPad, the texts of DDC data & table (128 bytes, hex code) can be modified. If DDC TEXTS & HEX Table ar completely correct, it can be saved as .ddc flie to re-load it into DDC IC for DDC Data application. Fig. 26 Step 8: Turn off the monitor, exit the factory mode. Fig. 25 Factory Mode indicator 2. Access Factory Mode 1). Turn off monitor. 2). 3). Press "MENU" button, wait until the OSD menu with Characters "BDS 32*420WN6 EU V0.50.3 05051LC32*A 6K3*A1" (below OSD menu) come on the Screen of the monitor. Press power " " button.Then quickly push " " and " ",and hold this two buttons , then the screen comes out "Waiting For Automatic Adjustment ",then the screen will be black for one second untill comes out "Windows screen"] => then release this two buttons. 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 32 Go to cover page BDL3221 LCD/TV DDC Instructions Step 3: Modify DDC data (verify EDID version, week, year) Click (new function) icon from the tool bar, bring up Step 1 of 9 as shown in Fig. 31 . EDID46 DDC application provides the function selection and text change (select & fill out) from Step 1 to Step 9. Step 4: Modify DDC data (Monitor Serial No.) 1. Click Next , bring up Fig. 32. 3. Click OK button to confirm your selection. 4. Click icon (Read EDID function) to read DDC EDID data from monitor. The EDID codes will display on screen as shown in Fig. 30. Fig. 32 2. Select the DDC2Bi as the communication channel. As shown in Fig. 29. Fig. 29 Fig. 30 Fig. 31 Select and fill out, If necessary. Re-programming Digital DDC IC Step 1: After initialize alignment box, connecting all cables and box as shown in Fig. 27. Fig. 28 Step 2: Read DDC data from monitor 1. Click icon as shown in Fig. 11 from the tool bar to bring up the Channels "Configuration Setup" windows as shown in Fig. 28. Fig. 27 Click this button =====> D-sub to DVI-D cable 1=DVI-D connector 2=D-sub connector 3=Power Plug 2 1 3 D-sub cable DC Power 8 12V ~ PC To video card To printer port (LTP1) To Monitor Printer Port Fig. 38 Fig. 35 Fig. 36 7. Click Next , bring up Fig. 38. 4. Click Next , bring up Fig. 35. 5. Click Next , bring up Fig. 36. 6. Click Next , bring up Fig. 37. In this step, please confirm the Descriptor Data Type is Monitor Range Limits, and all the items are same as below. Fig. 37 2. Click Next , bring up Fig. 33. Fig. 33 Fig. 34 3. Click Next , bring up Fig. 34. 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 33 Go to cover page BDL3221 LCD/TV DDC Instructions 3. Click (Write EDID) icon from the tool bar to write DDC data. Then wait for 20-30 seconds ,DDC data will be finished Writing. Fig. 41 Fig. 39 8. Click Next , bring up Fig. 39. - Click Finish to exit the Step window. - Serial number can be filled up at this moment (for example, 123457). NOTE: You must modify the Serial NO. In step 9, otherwise the Serial NO. In OSD Couldn't be modified correctly. Step 5: Write DDC data 1. Configuration should be as Fig. 40. And press OK. Fig. 40 2. Click Save. Step 7: Exit DDC program Pull down the File menu and select Exit as shown in Fig. 43. Step 8: Turn off the monitor, exit the factory mode. Fig. 43 4) Push Menu to exit OSD menu. " " Fig.42 Step 6: Save DDC data Sometimes, you may need to save DDC data as a text file for using in other IC chip. To save DDC data, follow the steps below: 1. Click (Save) icon (or click "file"-> "save as") from the tool bar and give a file name as shown in Fig. 42. The file type is EDID46 file (*.ddc) which can be open in WordPad. By using WordPad, the texts of DDC data & table (128 bytes, hex code) can be modified. If DDC TEXTS & HEX Table ar completely correct, it can be saved as *.ddc flie to re-load it into DDC IC for DDC Data application. Factory Mode indicator 2. Access Factory Mode 1). Turn off monitor. 2). 3). Press "MENU" button, wait until the OSD menu with Characters "BDS 32*420WN6 EU V0.50.3 05051LC32*A 6K3*A1" (below OSD menu) come on the Screen of the monitor. Press power " " button.Then quickly push " " and " ",and hold this two buttons , then the screen comes out "Waiting For Automatic Adjustment ",then the screen will be black for one second untill comes out "Windows screen"] => then release this two buttons. 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 34 Go to cover page BDL3221 LCD/TV DDC DATA THE DISPLAY DATA CHANNEL (DDC_2B) CONTENT INCLUDING: (FOR BDL3221 ANALOG FOR LPL PANEL) ********************************************************************** EDID log file ********************************************************************** Vendor/Product Identification ID Manufacturer Name : PHL ID Product Code : 3408 (HEX. swap) ID Serial Number : 79 (HEX.) Week of Manufacture : 6 Year of Manufacture : 2005 EDID Version, Revision Version : 1 Revision : 3 Basic Display Parameters/Features Video Input Definition : Analog Video Input 0.700V/0.000V (0.70Vpp) without Blank-to-Black Setup Separate Sync without Composite Sync without Sync on Green no Serration required Maximum H Image Size : 69 Maximum V Image Size : 39 Display Transfer Characteristic : 2.2 (gamma) Feature Support (DPMS) : Standby Suspend no Active Off Display Type : RGB color display Standard Default Color Space : Primary color space Color Characteristics Red X coordinate : 0.64 Red Y coordinate : 0.343 Green X coordinate : 0.28 Green Y coordinate : 0.605 Blue X coordinate : 0.145 Blue Y coordinate : 0.065 White X coordinate : 0.285 White Y coordinate : 0.293 Established Timings Established Timings I : 640 x 480 @60Hz (IBM,VGA) 800 x 600 @56Hz (VESA) 800 x 600 @60Hz (VESA) Established Timings II : 1024 x 768 @60Hz (VESA) Manufacturer's timings : Standard Timing Identification #1 Horizontal active pixels : 1280 Aspect Ratio : 16:9 Refresh Rate : 60 Detailed Timing #1 Pixel Clock (MHz) : 79.5 H Active (pixels) : 1280 H Blanking (pixels) : 384 V Active (lines) : 768 V Blanking (lines) : 30 H Sync Offset (F Porch) (pixels) : 64 H Sync Pulse Width (pixels) : 128 V Sync Offset (F Porch) (lines) : 3 V Sync Pulse Width (lines) : 7 H Image Size (mm) : 697 V Image Size (mm) : 392 H Border (pixels) : 0 V Border (lines) : 0 Flags : Non-interlaced : Normal Display, No stereo : Digital Separate sync. : Positive Vertical Sync. : Positive Horizontal Sync. Detailed Timing #2 Pixel Clock (MHz) : 84.75 H Active (pixels) : 1360 H Blanking (pixels) : 416 V Active (lines) : 768 V Blanking (lines) : 30 H Sync Offset (F Porch) (pixels) : 72 H Sync Pulse Width (pixels) : 136 V Sync Offset (F Porch) (lines) : 3 V Sync Pulse Width (lines) : 5 H Image Size (mm) : 697 V Image Size (mm) : 392 H Border (pixels) : 0 V Border (lines) : 0 Flags : Non-interlaced : Normal Display, No stereo : Digital Separate sync. : Positive Vertical Sync. : Positive Horizontal Sync. Monitor Descriptor #3 Monitor Name : 320WN6 Monitor Descriptor #4 Monitor Range Limits Min. Vt rate Hz : 50 Max. Vt rate Hz : 75 Min. Horiz. rate kHz : 30 Max. Horiz. rate kHz : 63 Max. Supported Pixel : 80 No secondary GTF timing formula supported. Extension Flag : 0 Check sum : 96 (HEX.) ********************************************************************** EDID data (128 bytes) ********************************************************************** 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00 8: 41 9: 0c 10: 34 11: 08 12: 79 13: 00 14: 00 15: 00 16: 06 17: 0f 18: 01 19: 03 20: 68 21: 45 22: 27 23: 78 24: cc 25: fc 26: 30 27: a3 28: 57 29: 47 30: 9b 31: 25 32: 10 33: 49 34: 4b 35: 23 36: 08 37: 00 38: 81 39: c0 40: 01 41: 01 42: 01 43: 01 44: 01 45: 01 46: 01 47: 01 48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 0e 55: 1f 56: 00 57: 80 58: 51 59: 00 60: 1e 61: 30 62: 40 63: 80 64: 37 65: 00 66: b9 67: 88 68: 21 69: 00 70: 00 71: 1e 72: 1b 73: 21 74: 50 75: a0 76: 51 77: 00 78: 1e 79: 30 80: 48 81: 88 82: 35 83: 00 84: b9 85: 88 86: 21 87: 00 88: 00 89: 1e 90: 00 91: 00 92: 00 93: fc 94: 00 95: 33 96: 32 97: 30 98: 57 99: 4e 100: 36 101: 0a 102: 20 103: 20 104: 20 105: 20 106: 20 107: 20 108: 00 109: 00 110: 00 111: fd 112: 00 113: 32 114: 4b 115: 1e 116: 3f 117: 08 118: 00 119: 0a 120: 20 121: 20 122: 20 123: 20 124: 20 125: 20 126: 00 127: 96 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 35 Go to cover page BDL3221 LCD/TV DDC DATA THE DISPLAY DATA CHANNEL (DDC_2B) CONTENT INCLUDING: (FOR BDL3221 DIGITAL FOR LPL PANEL) ********************************************************************** EDID log file ********************************************************************** Vendor/Product Identification ID Manufacturer Name : PHL ID Product Code : 3408 (HEX. swap) ID Serial Number : 79 (HEX.) Week of Manufacture : 6 Year of Manufacture : 2005 EDID Version, Revision Version : 1 Revision : 3 Basic Display Parameters/Features Video Input Definition : Digital Video Input Maximum H Image Size : 69 Maximum V Image Size : 39 Display Transfer Characteristic : 2.2 (gamma) Feature Support (DPMS) : Standby Suspend no Active Off Display Type : RGB color display Standard Default Color Space : Primary color space Color Characteristics Red X coordinate : 0.64 Red Y coordinate : 0.343 Green X coordinate : 0.28 Green Y coordinate : 0.605 Blue X coordinate : 0.145 Blue Y coordinate : 0.065 White X coordinate : 0.285 White Y coordinate : 0.293 Established Timings Established Timings I : 640 x 480 @60Hz (IBM,VGA) 800 x 600 @56Hz (VESA) 800 x 600 @60Hz (VESA) Established Timings II : 1024 x 768 @60Hz (VESA) Manufacturer's timings : Standard Timing Identification #1 Horizontal active pixels : 1280 Aspect Ratio : 16:9 Refresh Rate : 60 Detailed Timing #1 Pixel Clock (Mhz) : 74.5 H Active (pixels) : 1920 H Blanking (pixels) : 280 V Active (lines) : 1080 V Blanking (lines) : 45 H Sync Offset (F Porch) (pixels) : 44 H Sync Pulse Width (pixels) : 44 V Sync Offset (F Porch) (lines) : 2 V Sync Pulse Width (lines) : 5 H Image Size (mm) : 697 V Image Size (mm) : 392 H Border (pixels) : 0 V Border (lines) : 0 Flags : Interlaced : Normal Display, No stereo : Digital Separate sync. : Positive Vertical Sync. : Positive Horizontal Sync. Detailed Timing #2 Pixel Clock (MHz) : 84.75 H Active (pixels) : 1360 H Blanking (pixels) : 416 V Active (lines) : 768 V Blanking (lines) : 30 H Sync Offset (F Porch) (pixels) : 72 H Sync Pulse Width (pixels) : 136 V Sync Offset (F Porch) (lines) : 3 V Sync Pulse Width (lines) : 5 H Image Size (mm) : 697 V Image Size (mm) : 392 H Border (pixels) : 0 V Border (lines) : 0 Flags : Non-interlaced : Normal Display, No stereo : Digital Separate sync. : Positive Vertical Sync. : Positive Horizontal Sync. Monitor Descriptor #3 Monitor Name : 320WN6 Monitor Descriptor #4 Monitor Range Limits Min. Vt rate Hz : 50 Max. Vt rate Hz : 75 Min. Horiz. rate kHz : 30 Max. Horiz. rate kHz : 63 Max. Supported Pixel : 80 No secondary GTF timing formula supported. Extension Flag : 0 Check sum : DF (HEX.) ********************************************************************** EDID data (128 bytes) ********************************************************************** 0: 00 1: ff 2: ff 3: ff 4: ff 5: ff 6: ff 7: 00 8: 41 9: 0c 10: 34 11: 08 12: 79 13: 00 14: 00 15: 00 16: 06 17: 0f 18: 01 19: 03 20: 80 21: 45 22: 27 23: 78 24: cc 25: fc 26: 30 27: a3 28: 57 29: 47 30: 9b 31: 25 32: 10 33: 49 34: 4b 35: 23 36: 08 37: 00 38: 81 39: c0 40: 01 41: 01 42: 01 43: 01 44: 01 45: 01 46: 01 47: 01 48: 01 49: 01 50: 01 51: 01 52: 01 53: 01 54: 1a 55: 1d 56: 80 57: 18 58: 71 59: 38 60: 2d 61: 40 62: 2c 63: 2c 64: 25 65: 00 66: b9 67: 88 68: 21 69: 00 70: 00 71: 9e 72: 1b 73: 21 74: 50 75: a0 76: 51 77: 00 78: 1e 79: 30 80: 48 81: 88 82: 35 83: 00 84: b9 85: 88 86: 21 87: 00 88: 00 89: 1e 90: 00 91: 00 92: 00 93: fc 94: 00 95: 33 96: 32 97: 30 98: 57 99: 4e 100: 36 101: 0a 102: 20 103: 20 104: 20 105: 20 106: 20 107: 20 108: 00 109: 00 110: 00 111: fd 112: 00 113: 32 114: 4b 115: 1e 116: 3f 117: 08 118: 00 119: 0a 120: 20 121: 20 122: 20 123: 20 124: 20 125: 20 126: 00 127: df 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 36 Go to cover page BDL3221 LCD/TV ISP Instructions Update the firmware 1. Double click the Easywriter.exe icon in desktop then appears window as shown in Fig.7 . Step 5 :Copy the BDS42AP_V094_5826 to C:\320WN6 as shown in Fig. 5 . 6. Install and setup the Easywriter program Step 1 : Make a folder in your PC as shown in Fig. 3. For example : C:\BDL3221 Step 2 : Copy ISP Software Easywriter into your folder as shown in Fig.3. Step 3 : Unzip Easywriter.zip into your folder as shown in Fig. 3. Step 4 : Double click the EasywriterV2.09a_user.exe icon to install the Application as Fig. 4. .zip Configuration and procedure "Easywriter " The software is provided by Novatek to upgrade the firmware of CPU. DDC2BI_ISP TOOL (3138 149 53161) is for the interface between "Parallel Port of PC" and "15 pin-D-SUB connector of Monitor". It is a windows-based program, which cannot be run in MS-DOS. System and equipment requirements 1. An i486 (or above) personal computer or compatible. 2. Microsoft operation system Windows 95/98/2000/XP. 4. as shown in Fig. 1 3. ISP Software " Easywrite " DDC2BI_ISP TOOL (3138 106 10396) 5. Connect and Mains cord to Monitor as shown in Fig. 2. DDC2BI_ISP TOOL Fig. 1 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Parallel Port to Print Port in PC D-SUB to monitor Fig.2 PC To printer port (LTP1) To video card Video cable Connect to Mains cord Monitor (A) 320WN6 -Monitor (B) D-Sub Connect to Mains cord at this moment. -------------------------------> ISP box Fig. 3 2. Press the Load hex then select the hex as shown in Fig. 8. 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 37 Go to cover page BDL3221 LCD/TV ISP Instructions Fig. 8 If there is a warring message coming as shown in Fig 12. , you have to check the AC power, Video cable, or Novatek MCU. Fig. 10 Fig. 11 Fig. 13 4 Press the file --> exit to end program , as shown in Fig. 11. 4) Turn off the monitor, exit the factory mode. Fig. 14 3 Press the AUTO to running program , the firmware be updated as shown in Fig. 9~10. Fig. 12 Fig. 9 Factory Mode indicator 5 Check the firmware version 1). Turn off monitor. 2). 3). Press "MENU" button, wait until the OSD menu come on the Screen of the monitor.You will find, after upgrade, the version have already changed from The former"BDS 32*420WN6 EU V0.50.3 05051LC32*A6K3*A1" to the Present "AP BDS 32- 420WN6 V0.95.1 050802 LC32*A6K3*A1"as shown in Fig. 13 and Fig. 14. Press power " " button.Then quickly push " " and " ",and hold this two buttons , then the screen comes out "Waiting For Automatic Adjustment ",then the screen will be black for one second untill comes out "Windows screen"] => then release this two buttons. Factory Mode indicator 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 38 Go to cover page BDL3221 LCD/TV Failure description Phenomenon Vertical block defect Vertical dim lines Vertical lines defect (Always bright or dark) Horizontal block defect Horizontal dim lines Horizontal lines defect (Always bright or dark) Has bright or dark pixel Polarizer has bubbles Polarizer has bubbles Foreign material inside polarizer. It shows liner or dot shape. Concentric circle formed Bottom back light of LCD is brighter than normal Back light un-uniformity Backlight has foreign material. Black or white color, liner or circular type Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical instruction on this manual to eliminate failure by replace LCD panel. Failure Mode Of Panel 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 39 Go to cover page BDL 3221 LCD/TV Wiring Diagram 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 Block Diagram 40 Go to cover page BDL 3221 LCD/TV Main board Architecture of LCD TV Monitor (BackView ) PCB dimension & connectors position 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 41 Go to cover page BDL 3221 LCD/TV Scaler Diagram-1 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 42 Go to cover page BDL 3221 LCD/TV Scaler Diagram-2 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 43 Go to cover page BDL 3221 LCD/TV Scaler Diagram-3 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 44 Go to cover page BDL 3221 LCD/TV Scaler Diagram-4 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 45 Go to cover page BDL 3221 LCD/TV Scaler Diagram-5 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 46 Go to cover page BDL 3221 LCD/TV Scaler Diagram-6 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 47 Go to cover page BDL 3221 LCD/TV Scaler Diagram-7 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 48 Go to cover page BDL 3221 LCD/TV Scaler Diagram-8 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 49 Go to cover page BDL 3221 LCD/TV Scaler Diagram-9 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 50 Go to cover page BDL 3221 LCD/TV Scaler Diagram-10 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 51 Go to cover page BDL 3221 LCD/TV Scaler Diagram-11 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 52 Go to cover page BDL 3221 LCD/TV Scaler Diagram-12 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 53 Go to cover page BDL 3221 LCD/TV Scaler Diagram-13 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 54 Go to cover page BDL 3221 LCD/TV Scaler Diagram-14 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 55 Go to cover page BDL 3221 LCD/TV Scaler Diagram-15 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 56 Go to cover page BDL 3221 LCD/TV Scaler Diagram-16 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 57 Go to cover page BDL 3221 LCD/TV Scaler Board C.B.A.-1 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 58 Go to cover page BDL 3221 LCD/TV Scaler Board C.B.A.-2 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 59 Go to cover page BDL 3221 LCD/TV Power Diagram 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 60 Go to cover page BDL 3221 LCD/TV Power Board C.B.A.-1 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 61 Go to cover page BDL 3221 LCD/TV Power Board C.B.A.-2 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 62 Go to cover page BDL 3221 LCD/TV Control Diagram&C.B.A 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 63 Go to cover page BDL 3221 LCD/TV DSUB Diagram&C.B.A 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 64 Go to cover page BDL 3221 LCD/TV IR Diagram&C.B.A 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 65 Go to cover page BDL3221 LCD/TV Exploded View 313815760441 BACK COVER ASSY 40 313815137521 SHIELDING -SCALER BOTTOM 94 823827717361 LCD LC320W01-A6K1 1050 313815863541 CONTROL PCB ASSY 1055 313815862301 DSUB ADAPOTOR PCB ASSY 1053 313815137571 TV COVER 91 313815864721 SCALER ASSY(32-WE) 1057 313815137511 SHIELDING -SCALER RIGHT 93 313815864611 POWER PCB ASSY - BDS 32" 1058 313815137501 BOTTOM MAIN FRAME 60 313815137531 METAL BLOCK-GAP 95 313815863551 IR PCB ASSY 1056 313815760041 FRONT BEZEL ASSY(B) 30 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 66 Go to cover page BDL3221 LCD/TV Spare Parts List Model: BDL3221V/00(LPL) 12NC: 8639 000 16304 Mechanical Parts 7 313815760051 BASE ASSY 30 313815760041 FRONT BEZEL ASSY(B) 31 313815161951 FRONT BEZEL 32 313815416701 FRONT CORNER-B/R(BLACK) 33 313815416691 FRONT CORNER-T/R(BLACK) 34 313815410821 LENS 37 313815321431 RUBBER STRIP 38 313815321441 RUBBER-650X15X2 39 313815321451 RUBBER - 360X15X2 40 313815760441 BACK COVER ASSY 41 313815137491 BACK COVER 42 313815410812 CONTROL BOTTON 44 313815416431 HANDLE CLIP 46 313815137431 HANDLE HOLDER 47 313815137421 HANDLE 60 313815137501 BOTTOM MAIN FRAME 91 313815137571 TV COVER 93 313815137511 SHIELDING -SCALER RIGHT 94 313815137521 SHIELDING -SCALER BOTTOM 95 313815137531 METAL BLOCK-GAP 221 313815137381 TV HOUSING 452 313815640741 BOTTOM SLIP BOARD 464 314105631521 SMALL PLASTIC HANDLE 1176 313923811281 PROD ASSY RC1124134/01 PKD 1180 313815864841 MAIN FRAME+WIRE ASSY Packing Parts 129 313810650281 P.E. BAG (INSTR. BOOK) 455 313815640731 P.E. BAG 456 313815640751 CARTON 457 313815640701 CUSHION-TOP 458 313815640711 CUSHION-BTM Accessory 145 313811708821 E-D.F.U.(32") 1171 313818871672 MAINSCORD UK 10A 1M8 DET BK 1172 313812874931 MAINSCORD 1173 313819872601 CORD DVI 18+1/1M8/DVI 18+1 B 1175 313819871451 CORD SUB-D 15/1M8/SUB-D 15 B miscellanea 126 313815567771 RATING LABEL 291 313815567691 LABEL(LG-WE) 292 313815567691 LABEL(LG-WE) 615 313811708611 HEX CODE OF F/W(NO MATL REQ) 1001 242202518823 CON V 10P M 2.00 63390 1051 313819876041 SOC POW H 3P F AC CABL/100 1052 242208600208 FUSE 5X20 HT 4A 250V IEC 1071 242202518818 CON V 6P M 2.00 63386 1071 243803100099 CON V 2P M 2.50 63171 1086 242202518816 CON V 4P M 2.00 63384 1087 242212803035 SWI TACT SM 1P 1POS SKQGAB 1088 242212803035 SWI TACT SM 1P 1POS SKQGAB 1088 242202518904 CON V 12P M 2.50 64842 1089 242212803035 SWI TACT SM 1P 1POS SKQGAB 1089 242202518903 CON V 10P M 2.50 64840 1090 243812800224 SWI PUSH 2P 0.2A 20V SFPC12 1091 242212803035 SWI TACT SM 1P 1POS SKQGAB 1092 242212803035 SWI TACT SM 1P 1POS SKQGAB 1093 242212803035 SWI TACT SM 1P 1POS SKQGAB 1101 242254301364 RES XTL SM 18M432 16P SMD-49 1185 823827718021 LSP BOX 8R 10W L/R(P302H) 1192 823827718601 SPEAKER CABLE 4P (L/R) 1210 242202605769 SOC PHONE H 1P F 3.5 ST BK 1211 242202518432 SOC SUBD H 15P F SBFR 1251 313815859171 DIODE ASSY GBU6J 6051 1252 313815859181 DIODE ASSY STTH5L06 6052 1253 313815859191 DIODE ASSY( 6071,6076) 1254 313815859211 POW TRANS ASSY 7057/ 7062 1255 313815864731 CPU ASSY (LG-WE) 1256 313815864741 EEPROM ASSY (LG-WE) 1301 242203300558 SOC COMBI H 44P F DVI-I/SUBD 1401 243854300086 RES XTL SM 14M318 18P HC49/S 1402 242202518804 CON V 30P M 1.25 SM 60948 1507 242248680958 SOC IC V 52P F 1.77 DIL 1509 243803100435 SOC IC V 8P F 2.54 DIL 1601 313818876611 SOC EURO H 21P F SHE L-GRND 1615 242202518822 CON V 9P M 2.00 63389 1651 242202519075 SOC SUBD H 9P+9P M GN 1297 1698 242202518822 CON V 9P M 2.00 63389 1699 242202518954 SOC SUBD H 9P F BK 1211 1710 242202605803 SOC CINCH H 1P F 1L1 YE 1714 243803100428 SOC CINCH H 2P F 2L1 WHRD 1715 242202605554 SOC CINCH H 8P F 2L4 1719 242202605745 SOC MDIN H 4P F SH 1481-723 1741 243854300089 RES XTL SM 24M576 16P HC49/S 1781 243854300079 RES XTL SM 12MHZ 32P SMD-49 1852 242202518816 CON V 4P M 2.00 63384 1853 242202518819 CON V 7P M 2.00 63387 1854 242202518818 CON V 6P M 2.00 63386 1855 242202518816 CON V 4P M 2.00 63384 1856 242254301508 RES XTL SM 11M059 20P SMD-49 1901 313816877251 EARPHONE JACK 1902 242202518815 CON V 3P M 2.00 63383 1903 242202518814 CON V 2P M 2.00 63382 4444 313810610485 CD ROM - SERVICE MANUAL 4444 313810610486 SERVICE MANUAL 8055 313819876161 CBLE-390 10/160/10-020 AWG26 8152 313819876122 CBLE-019 9/130/9-019 AWG28 8174 313819876151 CBLE-130 30/270/30-033 AWG28 8175 313819876191 CBLE-392 12/620+200/12-022 8177 313819876171 CBLE-014 4/420/4-014 AWG28 8178 313819876181 CBLE-016 6/480/6-016 AWG28 LCD Panel 1050 823827717361 LCD LC320W01-A6K1 PCB Assy 1053 313815862301 DSUB ADAPOTOR PCB ASSY 1055 313815863541 CONTROL PCB ASSY 1056 313815863551 IR PCB ASSY 1057 313815864721 SCALER ASSY(32-WE) 1058 313815864611 POWER PCB ASSY - BDS 32" PCB Assy 1057 313815864721 SCALER ASSY(32-WE) 2002 223858619807 CER2 0603 Y5V 50V 22N P8020 2003 203803513313 ELCAP RGA 25V S 100U PM20 2004 223858619812 CER2 0603 Y5V 50V 100N P8020 2005 223878616641 CER2 0603 X7R 16V 22N PM10 2006 223886715221 CER1 0603 NP0 50V 220P PM5 2007 202203100074 ELCAP KM 16V S 1000U PM20 2008 203803513313 ELCAP RGA 25V S 100U PM20 2009 222224119876 CER2 1206 Y5V 10V 10U P8020 2010 202203100074 ELCAP KM 16V S 1000U PM20 2011 202203100074 ELCAP KM 16V S 1000U PM20 2012 202203100207 ELCAP SM RVS 16V 10U PM20 2013 202203100074 ELCAP KM 16V S 1000U PM20 2014 223858115649 CER2 1206 X7R 50V 100N PM10 2015 203803511407 ELCAP REA 35V S 100U PM20 2016 223886715221 CER1 0603 NP0 50V 220P PM5 2018 223886715221 CER1 0603 NP0 50V 220P PM5 2019 223858619807 CER2 0603 Y5V 50V 22N P8020 2020 223891619849 CER2 0603 Y5V 25V 100N P8020 2021 202202000982 ELCAP GS 35V S 100U PM20 2022 223858115649 CER2 1206 X7R 50V 100N PM10 2023 223858619807 CER2 0603 Y5V 50V 22N P8020 2024 223886715221 CER1 0603 NP0 50V 220P PM5 2025 202203100074 ELCAP KM 16V S 1000U PM20 2101 222224119876 CER2 1206 Y5V 10V 10U P8020 2102 223824619863 CER2 0603 Y5V 10V 1U P8020 2103 223824619863 CER2 0603 Y5V 10V 1U P8020 2104 223824619863 CER2 0603 Y5V 10V 1U P8020 2105 223824619863 CER2 0603 Y5V 10V 1U P8020 2106 223824619863 CER2 0603 Y5V 10V 1U P8020 2107 223824619863 CER2 0603 Y5V 10V 1U P8020 2108 223824619863 CER2 0603 Y5V 10V 1U P8020 2109 223824619863 CER2 0603 Y5V 10V 1U P8020 2110 222224119876 CER2 1206 Y5V 10V 10U P8020 2111 222258015649 CER2 0805 X7R 50V 100N PM10 2112 223886715159 CER1 0603 NP0 50V 15P PM5 2113 223886715479 CER1 0603 NP0 50V 47P PM5 2114 223824619863 CER2 0603 Y5V 10V 1U P8020 2115 223824619863 CER2 0603 Y5V 10V 1U P8020 2116 223824619863 CER2 0603 Y5V 10V 1U P8020 2117 223824619863 CER2 0603 Y5V 10V 1U P8020 2118 223824619863 CER2 0603 Y5V 10V 1U P8020 2119 223824619863 CER2 0603 Y5V 10V 1U P8020 2121 223824619863 CER2 0603 Y5V 10V 1U P8020 2122 223824619863 CER2 0603 Y5V 10V 1U P8020 2123 222258015649 CER2 0805 X7R 50V 100N PM10 2124 222258015649 CER2 0805 X7R 50V 100N PM10 2125 223824615654 CER2 0603 X7R 10V 220N PM10 2126 222224119876 CER2 1206 Y5V 10V 10U P8020 2127 222224119876 CER2 1206 Y5V 10V 10U P8020 2128 222224119876 CER2 1206 Y5V 10V 10U P8020 2129 223878615649 CER2 0603 X7R 16V 100N PM10 2131 222224119876 CER2 1206 Y5V 10V 10U P8020 2132 222224119876 CER2 1206 Y5V 10V 10U P8020 2133 223858615632 CER2 0603 X7R 50V 4N7 PM10 2134 223858615632 CER2 0603 X7R 50V 4N7 PM10 2135 223824619863 CER2 0603 Y5V 10V 1U P8020 2136 223824619863 CER2 0603 Y5V 10V 1U P8020 2137 223824619863 CER2 0603 Y5V 10V 1U P8020 2138 223824619863 CER2 0603 Y5V 10V 1U P8020 2139 222224119876 CER2 1206 Y5V 10V 10U P8020 2141 222258015649 CER2 0805 X7R 50V 100N PM10 2142 222258015649 CER2 0805 X7R 50V 100N PM10 2143 223886715159 CER1 0603 NP0 50V 15P PM5 2144 223886715159 CER1 0603 NP0 50V 15P PM5 2161 223878615649 CER2 0603 X7R 16V 100N PM10 2162 223878615649 CER2 0603 X7R 16V 100N PM10 2163 223878615649 CER2 0603 X7R 16V 100N PM10 2164 223878615649 CER2 0603 X7R 16V 100N PM10 2165 223886715159 CER1 0603 NP0 50V 15P PM5 2166 223878615649 CER2 0603 X7R 16V 100N PM10 2201 222224119876 CER2 1206 Y5V 10V 10U P8020 2202 223886715339 CER1 0603 NP0 50V 33P PM5 2203 223886715109 CER1 0603 NP0 50V 10P PM5 2204 223886715101 CER1 0603 NP0 50V 100P PM5 2205 223886715568 CER1 0603 NP0 50V 5P6 PM0P5 2206 223886715568 CER1 0603 NP0 50V 5P6 PM0P5 2207 223886715568 CER1 0603 NP0 50V 5P6 PM0P5 2208 223878615649 CER2 0603 X7R 16V 100N PM10 2209 223891619849 CER2 0603 Y5V 25V 100N P8020 2211 223886715331 CER1 0603 NP0 50V 330P PM5 2212 223886715331 CER1 0603 NP0 50V 330P PM5 2213 223886715331 CER1 0603 NP0 50V 330P PM5 2214 223886715331 CER1 0603 NP0 50V 330P PM5 2301 223878615649 CER2 0603 X7R 16V 100N PM10 2302 223878615649 CER2 0603 X7R 16V 100N PM10 2401 223878615649 CER2 0603 X7R 16V 100N PM10 2402 223858615636 CER2 0603 X7R 50V 10N PM10 2403 223878615649 CER2 0603 X7R 16V 100N PM10 2404 202002191726 ELCAP SM RVS 16V 47U PM20 2405 222224119876 CER2 1206 Y5V 10V 10U P8020 2406 223878615649 CER2 0603 X7R 16V 100N PM10 2407 223878615649 CER2 0603 X7R 16V 100N PM10 2408 223878615649 CER2 0603 X7R 16V 100N PM10 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 67 Go to cover page BDL3221 LCD/TV Spare Parts List 2409 223878615649 CER2 0603 X7R 16V 100N PM10 2410 223878615649 CER2 0603 X7R 16V 100N PM10 2411 223878615649 CER2 0603 X7R 16V 100N PM10 2412 223878615649 CER2 0603 X7R 16V 100N PM10 2413 222224119876 CER2 1206 Y5V 10V 10U P8020 2414 223878615649 CER2 0603 X7R 16V 100N PM10 2415 223878615649 CER2 0603 X7R 16V 100N PM10 2416 223858615636 CER2 0603 X7R 50V 10N PM10 2417 223878615649 CER2 0603 X7R 16V 100N PM10 2418 223878615649 CER2 0603 X7R 16V 100N PM10 2419 223878615645 CER2 0603 X7R 16V 47N PM10 2420 222224119876 CER2 1206 Y5V 10V 10U P8020 2421 223878615649 CER2 0603 X7R 16V 100N PM10 2422 223878615649 CER2 0603 X7R 16V 100N PM10 2423 223878615649 CER2 0603 X7R 16V 100N PM10 2424 223878615649 CER2 0603 X7R 16V 100N PM10 2425 222224119876 CER2 1206 Y5V 10V 10U P8020 2426 223878615649 CER2 0603 X7R 16V 100N PM10 2427 223878615649 CER2 0603 X7R 16V 100N PM10 2428 222224119876 CER2 1206 Y5V 10V 10U P8020 2429 223878615649 CER2 0603 X7R 16V 100N PM10 2430 223878615649 CER2 0603 X7R 16V 100N PM10 2431 223878615645 CER2 0603 X7R 16V 47N PM10 2432 223886715181 CER1 0603 NP0 50V 180P PM5 2433 223858615623 CER2 0603 X7R 50V 1N PM10 2434 223878615645 CER2 0603 X7R 16V 47N PM10 2435 223878615645 CER2 0603 X7R 16V 47N PM10 2436 223858615623 CER2 0603 X7R 50V 1N PM10 2437 223878615645 CER2 0603 X7R 16V 47N PM10 2438 223878615645 CER2 0603 X7R 16V 47N PM10 2439 223878615645 CER2 0603 X7R 16V 47N PM10 2440 223878615645 CER2 0603 X7R 16V 47N PM10 2441 223878615645 CER2 0603 X7R 16V 47N PM10 2442 223878615649 CER2 0603 X7R 16V 100N PM10 2443 202002191726 ELCAP SM RVS 16V 47U PM20 2445 223886715229 CER1 0603 NP0 50V 22P PM5 2446 223886715229 CER1 0603 NP0 50V 22P PM5 2448 223878615649 CER2 0603 X7R 16V 100N PM10 2449 223878615649 CER2 0603 X7R 16V 100N PM10 2450 223878615649 CER2 0603 X7R 16V 100N PM10 2451 222224119876 CER2 1206 Y5V 10V 10U P8020 2452 223878619854 CER2 0603 Y5V 16V 220N P8020 2453 223878615649 CER2 0603 X7R 16V 100N PM10 2471 222224119876 CER2 1206 Y5V 10V 10U P8020 2472 223878615649 CER2 0603 X7R 16V 100N PM10 2473 223878615649 CER2 0603 X7R 16V 100N PM10 2474 223878615649 CER2 0603 X7R 16V 100N PM10 2475 223878615649 CER2 0603 X7R 16V 100N PM10 2476 223878615649 CER2 0603 X7R 16V 100N PM10 2477 222224119876 CER2 1206 Y5V 10V 10U P8020 2478 223878615649 CER2 0603 X7R 16V 100N PM10 2479 223878615649 CER2 0603 X7R 16V 100N PM10 2481 223878615649 CER2 0603 X7R 16V 100N PM10 2482 223878615649 CER2 0603 X7R 16V 100N PM10 2483 223878615649 CER2 0603 X7R 16V 100N PM10 2484 222224119876 CER2 1206 Y5V 10V 10U P8020 2601 223886715471 CER1 0603 NP0 50V 470P PM5 2602 223886715331 CER1 0603 NP0 50V 330P PM5 2603 223886715331 CER1 0603 NP0 50V 330P PM5 2604 223886715471 CER1 0603 NP0 50V 470P PM5 2605 223886715471 CER1 0603 NP0 50V 470P PM5 2606 223886715331 CER1 0603 NP0 50V 330P PM5 2607 223886715331 CER1 0603 NP0 50V 330P PM5 2608 223886715331 CER1 0603 NP0 50V 330P PM5 2609 223886715331 CER1 0603 NP0 50V 330P PM5 2611 223886715331 CER1 0603 NP0 50V 330P PM5 2612 223886715229 CER1 0603 NP0 50V 22P PM5 2613 223886715229 CER1 0603 NP0 50V 22P PM5 2614 223886715229 CER1 0603 NP0 50V 22P PM5 2616 223886715229 CER1 0603 NP0 50V 22P PM5 2618 223878615649 CER2 0603 X7R 16V 100N PM10 2619 223886715331 CER1 0603 NP0 50V 330P PM5 2631 223858619812 CER2 0603 Y5V 50V 100N P8020 2632 223858619812 CER2 0603 Y5V 50V 100N P8020 2633 223858619812 CER2 0603 Y5V 50V 100N P8020 2634 223858619812 CER2 0603 Y5V 50V 100N P8020 2635 222224119876 CER2 1206 Y5V 10V 10U P8020 2636 223858619812 CER2 0603 Y5V 50V 100N P8020 2637 222224119876 CER2 1206 Y5V 10V 10U P8020 2638 223858619812 CER2 0603 Y5V 50V 100N P8020 2639 222224119881 CER2 1206 Y5V 10V 22U P8020 2641 222224119876 CER2 1206 Y5V 10V 10U P8020 2642 222224119876 CER2 1206 Y5V 10V 10U P8020 2643 222224119876 CER2 1206 Y5V 10V 10U P8020 2644 202202001027 ELCAP SM LV 4V 220U PM20 2645 202202001027 ELCAP SM LV 4V 220U PM20 2646 202202001027 ELCAP SM LV 4V 220U PM20 2651 222258015649 CER2 0805 X7R 50V 100N PM10 2652 222224119876 CER2 1206 Y5V 10V 10U P8020 2653 223824619863 CER2 0603 Y5V 10V 1U P8020 2654 223824619863 CER2 0603 Y5V 10V 1U P8020 2655 223824619863 CER2 0603 Y5V 10V 1U P8020 2656 223824619863 CER2 0603 Y5V 10V 1U P8020 2657 223824619863 CER2 0603 Y5V 10V 1U P8020 2677 222224119876 CER2 1206 Y5V 10V 10U P8020 2678 202203100074 ELCAP KM 16V S 1000U PM20 2679 223886715229 CER1 0603 NP0 50V 22P PM5 2701 223886715331 CER1 0603 NP0 50V 330P PM5 2702 223886715331 CER1 0603 NP0 50V 330P PM5 2703 223886715331 CER1 0603 NP0 50V 330P PM5 2704 223886715331 CER1 0603 NP0 50V 330P PM5 2705 223886715331 CER1 0603 NP0 50V 330P PM5 2706 223886715331 CER1 0603 NP0 50V 330P PM5 2707 223886715331 CER1 0603 NP0 50V 330P PM5 2708 223886715331 CER1 0603 NP0 50V 330P PM5 2709 223886715331 CER1 0603 NP0 50V 330P PM5 2711 223886715331 CER1 0603 NP0 50V 330P PM5 2713 223886715331 CER1 0603 NP0 50V 330P PM5 2715 223886715331 CER1 0603 NP0 50V 330P PM5 2742 223878616641 CER2 0603 X7R 16V 22N PM10 2743 223878616641 CER2 0603 X7R 16V 22N PM10 2744 223878616641 CER2 0603 X7R 16V 22N PM10 2746 223878616641 CER2 0603 X7R 16V 22N PM10 2747 223878616641 CER2 0603 X7R 16V 22N PM10 2748 223878616641 CER2 0603 X7R 16V 22N PM10 2749 223878616641 CER2 0603 X7R 16V 22N PM10 2751 223878616641 CER2 0603 X7R 16V 22N PM10 2753 223878616641 CER2 0603 X7R 16V 22N PM10 2754 223878616641 CER2 0603 X7R 16V 22N PM10 2755 223878616641 CER2 0603 X7R 16V 22N PM10 2756 223878616641 CER2 0603 X7R 16V 22N PM10 2757 223878615649 CER2 0603 X7R 16V 100N PM10 2758 223878615649 CER2 0603 X7R 16V 100N PM10 2759 222224119876 CER2 1206 Y5V 10V 10U P8020 2761 223878615649 CER2 0603 X7R 16V 100N PM10 2762 223878615649 CER2 0603 X7R 16V 100N PM10 2763 223878615649 CER2 0603 X7R 16V 100N PM10 2764 223878615649 CER2 0603 X7R 16V 100N PM10 2765 223878615649 CER2 0603 X7R 16V 100N PM10 2766 223878615649 CER2 0603 X7R 16V 100N PM10 2767 223878615649 CER2 0603 X7R 16V 100N PM10 2768 223878615649 CER2 0603 X7R 16V 100N PM10 2769 223878615649 CER2 0603 X7R 16V 100N PM10 2771 223878615649 CER2 0603 X7R 16V 100N PM10 2772 223886715279 CER1 0603 NP0 50V 27P PM5 2773 223886715279 CER1 0603 NP0 50V 27P PM5 2774 202002191726 ELCAP SM RVS 16V 47U PM20 2775 202002191726 ELCAP SM RVS 16V 47U PM20 2776 223878615649 CER2 0603 X7R 16V 100N PM10 2781 222224119876 CER2 1206 Y5V 10V 10U P8020 2782 223878615649 CER2 0603 X7R 16V 100N PM10 2783 223878615649 CER2 0603 X7R 16V 100N PM10 2784 222224119876 CER2 1206 Y5V 10V 10U P8020 2785 222224119876 CER2 1206 Y5V 10V 10U P8020 2786 223886715159 CER1 0603 NP0 50V 15P PM5 2787 223886715159 CER1 0603 NP0 50V 15P PM5 2788 222224119876 CER2 1206 Y5V 10V 10U P8020 2789 222224119876 CER2 1206 Y5V 10V 10U P8020 2791 223886715109 CER1 0603 NP0 50V 10P PM5 2792 223886715109 CER1 0603 NP0 50V 10P PM5 2793 223886715109 CER1 0603 NP0 50V 10P PM5 2801 223878615649 CER2 0603 X7R 16V 100N PM10 2802 223878615649 CER2 0603 X7R 16V 100N PM10 2803 223878615649 CER2 0603 X7R 16V 100N PM10 2804 223878615649 CER2 0603 X7R 16V 100N PM10 2805 223878615649 CER2 0603 X7R 16V 100N PM10 2806 223878615649 CER2 0603 X7R 16V 100N PM10 2807 223878615649 CER2 0603 X7R 16V 100N PM10 2808 223878615649 CER2 0603 X7R 16V 100N PM10 2809 223878615649 CER2 0603 X7R 16V 100N PM10 2811 223878615649 CER2 0603 X7R 16V 100N PM10 2812 223878615649 CER2 0603 X7R 16V 100N PM10 2813 223878615649 CER2 0603 X7R 16V 100N PM10 2814 223878615649 CER2 0603 X7R 16V 100N PM10 2815 223878615649 CER2 0603 X7R 16V 100N PM10 2816 223878615649 CER2 0603 X7R 16V 100N PM10 2817 223878615649 CER2 0603 X7R 16V 100N PM10 2818 223878615649 CER2 0603 X7R 16V 100N PM10 2819 223878615649 CER2 0603 X7R 16V 100N PM10 2821 223878615649 CER2 0603 X7R 16V 100N PM10 2822 223878615649 CER2 0603 X7R 16V 100N PM10 2823 223878615649 CER2 0603 X7R 16V 100N PM10 2824 223878615649 CER2 0603 X7R 16V 100N PM10 2825 223878615649 CER2 0603 X7R 16V 100N PM10 2826 223886715339 CER1 0603 NP0 50V 33P PM5 2827 223878615649 CER2 0603 X7R 16V 100N PM10 2851 223878615649 CER2 0603 X7R 16V 100N PM10 2852 223878615649 CER2 0603 X7R 16V 100N PM10 2853 222224119876 CER2 1206 Y5V 10V 10U P8020 2854 223886715229 CER1 0603 NP0 50V 22P PM5 2855 223886715229 CER1 0603 NP0 50V 22P PM5 2856 223858615623 CER2 0603 X7R 50V 1N PM10 2857 222224119876 CER2 1206 Y5V 10V 10U P8020 2858 223886715109 CER1 0603 NP0 50V 10P PM5 2859 223858615636 CER2 0603 X7R 50V 10N PM10 2861 223858615636 CER2 0603 X7R 50V 10N PM10 2865 223878615649 CER2 0603 X7R 16V 100N PM10 2866 223886715101 CER1 0603 NP0 50V 100P PM5 2867 223886715101 CER1 0603 NP0 50V 100P PM5 2868 223858615636 CER2 0603 X7R 50V 10N PM10 2869 223858015636 CER2 0805 X7R 50V 10N PM10 2871 223858615636 CER2 0603 X7R 50V 10N PM10 2872 223858615636 CER2 0603 X7R 50V 10N PM10 2873 202002191726 ELCAP SM RVS 16V 47U PM20 2901 202203100132 ELCAP LZ 25V S 1000U PM20 2902 223891015649 CER2 0805 X7R 25V 100N PM10 2903 202203100132 ELCAP LZ 25V S 1000U PM20 2904 203803511203 ELCAP REA 16V S 100U PM20 2905 223858615636 CER2 0603 X7R 50V 10N PM10 2906 223858615636 CER2 0603 X7R 50V 10N PM10 2907 203803511203 ELCAP REA 16V S 100U PM20 2908 223886715101 CER1 0603 NP0 50V 100P PM5 2909 223824619863 CER2 0603 Y5V 10V 1U P8020 2911 223878615649 CER2 0603 X7R 16V 100N PM10 2912 222224119876 CER2 1206 Y5V 10V 10U P8020 2913 222224119876 CER2 1206 Y5V 10V 10U P8020 2914 223886715101 CER1 0603 NP0 50V 100P PM5 2915 223824619863 CER2 0603 Y5V 10V 1U P8020 2916 223891619849 CER2 0603 Y5V 25V 100N P8020 2917 223891619849 CER2 0603 Y5V 25V 100N P8020 2918 223891619849 CER2 0603 Y5V 25V 100N P8020 2919 223891619849 CER2 0603 Y5V 25V 100N P8020 2923 202203100182 ELCAP SM RVS 25V 10U PM20 2924 223886715221 CER1 0603 NP0 50V 220P PM5 2925 223878619854 CER2 0603 Y5V 16V 220N P8020 2926 223878619854 CER2 0603 Y5V 16V 220N P8020 2928 223878619854 CER2 0603 Y5V 16V 220N P8020 2929 223878619854 CER2 0603 Y5V 16V 220N P8020 2932 223878619854 CER2 0603 Y5V 16V 220N P8020 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 68 Go to cover page BDL3221 LCD/TV Spare Parts List 2933 202203100182 ELCAP SM RVS 25V 10U PM20 2934 223891619849 CER2 0603 Y5V 25V 100N P8020 2935 223891619849 CER2 0603 Y5V 25V 100N P8020 2936 223891619849 CER2 0603 Y5V 25V 100N P8020 2937 223891619849 CER2 0603 Y5V 25V 100N P8020 2938 202203100182 ELCAP SM RVS 25V 10U PM20 2939 223891619849 CER2 0603 Y5V 25V 100N P8020 2941 223878615649 CER2 0603 X7R 16V 100N PM10 2942 223858119716 CER2 1206 Y5V 50V 470N PM20 2943 223878619854 CER2 0603 Y5V 16V 220N P8020 2944 223886715101 CER1 0603 NP0 50V 100P PM5 2945 223878615649 CER2 0603 X7R 16V 100N PM10 2946 223886715101 CER1 0603 NP0 50V 100P PM5 2947 223878619854 CER2 0603 Y5V 16V 220N P8020 2948 223878615649 CER2 0603 X7R 16V 100N PM10 2949 223878615649 CER2 0603 X7R 16V 100N PM10 2951 223886715101 CER1 0603 NP0 50V 100P PM5 2952 223886715101 CER1 0603 NP0 50V 100P PM5 2953 223858119716 CER2 1206 Y5V 50V 470N PM20 2954 202203100231 ELCAP SM HV 50V 1U PM20 2955 202203100231 ELCAP SM HV 50V 1U PM20 2956 223878619854 CER2 0603 Y5V 16V 220N P8020 2957 223878619854 CER2 0603 Y5V 16V 220N P8020 3001 232270260473 RST SM 0603 RC21 47K PM5 3002 212211805682 RST SM 0603 RC0603 82K PM5 3004 232270260101 RST SM 0603 RC21 100R PM5 3005 232270260473 RST SM 0603 RC21 47K PM5 3006 212211805669 RST SM 0603 RC0603 10K PM5 3007 232270260472 RST SM 0603 RC21 4K7 PM5 3008 232270463303 RST SM 0603 RC22H 33K PM1 3009 212211805676 RST SM 0603 RC0603 33K PM5 3010 212211805667 RST SM 0603 RC0603 6K8 PM5 3011 232270260472 RST SM 0603 RC21 4K7 PM5 3012 232270463002 RST SM 0603 RC22H 3K PM1 3013 232270461003 RST SM 0603 RC22H 10K PM1 3014 213810500082 RST MOX 1W RSS S 0R82 PM5 3015 232270461001 RST SM 0603 RC22H 100R PM1 3016 232270463902 RST SM 0603 RC22H 3K9 PM1 3017 232270260223 RST SM 0603 RC21 22K PM5 3018 232270260473 RST SM 0603 RC21 47K PM5 3019 212211805669 RST SM 0603 RC0603 10K PM5 3022 232270260101 RST SM 0603 RC21 100R PM5 3024 232270260101 RST SM 0603 RC21 100R PM5 3031 232270260472 RST SM 0603 RC21 4K7 PM5 3034 232270461002 RST SM 0603 RC22H 1K PM1 3035 232270260472 RST SM 0603 RC21 4K7 PM5 3036 232270462001 RST SM 0603 RC22H 200R PM1 3041 232270260101 RST SM 0603 RC21 100R PM5 3042 232270463302 RST SM 0603 RC22H 3K3 PM1 3043 232270463902 RST SM 0603 RC22H 3K9 PM1 3044 232270465602 RST SM 0603 RC22H 5K6 PM1 3045 232270463303 RST SM 0603 RC22H 33K PM1 3101 232270260222 RST SM 0603 RC21 2K2 PM5 3102 212211805687 RST SM 0603 RC0603 470K PM5 3103 212211805687 RST SM 0603 RC0603 470K PM5 3104 212211805687 RST SM 0603 RC0603 470K PM5 3105 212211805687 RST SM 0603 RC0603 470K PM5 3106 212211805687 RST SM 0603 RC0603 470K PM5 3107 212211805687 RST SM 0603 RC0603 470K PM5 3108 212211805687 RST SM 0603 RC0603 470K PM5 3109 212211805687 RST SM 0603 RC0603 470K PM5 3110 232270260222 RST SM 0603 RC21 2K2 PM5 3111 212211805669 RST SM 0603 RC0603 10K PM5 3112 212211805669 RST SM 0603 RC0603 10K PM5 3113 232270260101 RST SM 0603 RC21 100R PM5 3114 232270260101 RST SM 0603 RC21 100R PM5 3115 232270260273 RST SM 0603 RC21 27K PM5 3116 232270260101 RST SM 0603 RC21 100R PM5 3117 232270260101 RST SM 0603 RC21 100R PM5 3118 232270260101 RST SM 0603 RC21 100R PM5 3119 232270260101 RST SM 0603 RC21 100R PM5 3121 232270260101 RST SM 0603 RC21 100R PM5 3122 232270260101 RST SM 0603 RC21 100R PM5 3123 232270260101 RST SM 0603 RC21 100R PM5 3124 232270260101 RST SM 0603 RC21 100R PM5 3161 232270260471 RST SM 0603 RC21 470R PM5 3162 232270260473 RST SM 0603 RC21 47K PM5 3201 232270260472 RST SM 0603 RC21 4K7 PM5 3202 232270260101 RST SM 0603 RC21 100R PM5 3203 232270260101 RST SM 0603 RC21 100R PM5 3204 232270260472 RST SM 0603 RC21 4K7 PM5 3205 232270260101 RST SM 0603 RC21 100R PM5 3206 232270260472 RST SM 0603 RC21 4K7 PM5 3207 232270260472 RST SM 0603 RC21 4K7 PM5 3208 232270260101 RST SM 0603 RC21 100R PM5 3209 212211805642 RST SM 0603 RC0603 75R PM5 3211 232270260689 RST SM 0603 RC21 68R PM5 3212 232270260101 RST SM 0603 RC21 100R PM5 3213 212211805642 RST SM 0603 RC0603 75R PM5 3214 232270260689 RST SM 0603 RC21 68R PM5 3215 232270260101 RST SM 0603 RC21 100R PM5 3216 212211805642 RST SM 0603 RC0603 75R PM5 3217 232270260689 RST SM 0603 RC21 68R PM5 3218 232270260101 RST SM 0603 RC21 100R PM5 3219 232270260101 RST SM 0603 RC21 100R PM5 3221 232270260102 RST SM 0603 RC21 1K PM5 3222 232270260273 RST SM 0603 RC21 27K PM5 3223 232270260102 RST SM 0603 RC21 1K PM5 3224 232270260273 RST SM 0603 RC21 27K PM5 3225 232270260472 RST SM 0603 RC21 4K7 PM5 3301 232270260102 RST SM 0603 RC21 1K PM5 3302 232270260101 RST SM 0603 RC21 100R PM5 3303 232270260101 RST SM 0603 RC21 100R PM5 3304 232270260101 RST SM 0603 RC21 100R PM5 3305 232270260472 RST SM 0603 RC21 4K7 PM5 3306 232270260472 RST SM 0603 RC21 4K7 PM5 3307 232270260472 RST SM 0603 RC21 4K7 PM5 3401 213810500082 RST MOX 1W RSS S 0R82 PM5 3402 232270260101 RST SM 0603 RC21 100R PM5 3403 212211805651 RST SM 0603 RC0603 390R PM5 3404 232270260471 RST SM 0603 RC21 470R PM5 3405 232270260471 RST SM 0603 RC21 470R PM5 3406 212211805635 RST SM 0603 RC0603 10R PM5 3407 212211805635 RST SM 0603 RC0603 10R PM5 3408 212211805635 RST SM 0603 RC0603 10R PM5 3409 212211805635 RST SM 0603 RC0603 10R PM5 3410 212211805635 RST SM 0603 RC0603 10R PM5 3411 212211805635 RST SM 0603 RC0603 10R PM5 3412 212211805635 RST SM 0603 RC0603 10R PM5 3413 212211805635 RST SM 0603 RC0603 10R PM5 3414 235003510101 RST NETW SM ARV24 4X100R PM5 3415 235003510229 RST NETW SM ARV24 4X 22R PM5 3416 235003510229 RST NETW SM ARV24 4X 22R PM5 3417 235003510229 RST NETW SM ARV24 4X 22R PM5 3418 235003510229 RST NETW SM ARV24 4X 22R PM5 3419 235003510229 RST NETW SM ARV24 4X 22R PM5 3420 235003510229 RST NETW SM ARV24 4X 22R PM5 3421 235003510229 RST NETW SM ARV24 4X 22R PM5 3422 235003510229 RST NETW SM ARV24 4X 22R PM5 3423 235003510229 RST NETW SM ARV24 4X 22R PM5 3424 232270461002 RST SM 0603 RC22H 1K PM1 3425 232270461002 RST SM 0603 RC22H 1K PM1 3427 232270260102 RST SM 0603 RC21 1K PM5 3428 232270260689 RST SM 0603 RC21 68R PM5 3429 232270260689 RST SM 0603 RC21 68R PM5 3430 232270260689 RST SM 0603 RC21 68R PM5 3471 232270260339 RST SM 0603 RC21 33R PM5 3472 232270260339 RST SM 0603 RC21 33R PM5 3473 232270260339 RST SM 0603 RC21 33R PM5 3474 232270260339 RST SM 0603 RC21 33R PM5 3475 212211805645 RST SM 0603 RC0603 150R PM5 3476 212211805637 RST SM 0603 RC0603 22R PM5 3477 212211805637 RST SM 0603 RC0603 22R PM5 3478 212211805637 RST SM 0603 RC0603 22R PM5 3479 212211805637 RST SM 0603 RC0603 22R PM5 3601 212211805645 RST SM 0603 RC0603 150R PM5 3602 232270260101 RST SM 0603 RC21 100R PM5 3603 232270260224 RST SM 0603 RC21 220K PM5 3604 232270260102 RST SM 0603 RC21 1K PM5 3605 232270260273 RST SM 0603 RC21 27K PM5 3606 232270260101 RST SM 0603 RC21 100R PM5 3607 232270260224 RST SM 0603 RC21 220K PM5 3608 232270260102 RST SM 0603 RC21 1K PM5 3609 232270260273 RST SM 0603 RC21 27K PM5 3611 212211805642 RST SM 0603 RC0603 75R PM5 3612 232270260243 RST SM 0603 RC21 24K PM5 3613 212211805642 RST SM 0603 RC0603 75R PM5 3614 212211805642 RST SM 0603 RC0603 75R PM5 3615 232270260102 RST SM 0603 RC21 1K PM5 3616 232270260102 RST SM 0603 RC21 1K PM5 3617 232270260689 RST SM 0603 RC21 68R PM5 3618 232270260102 RST SM 0603 RC21 1K PM5 3619 232270462709 RST SM 0603 RC22H 27R PM1 3621 212211805639 RST SM 0603 RC0603 47R PM5 3622 232270260101 RST SM 0603 RC21 100R PM5 3623 232270260101 RST SM 0603 RC21 100R PM5 3624 232270260101 RST SM 0603 RC21 100R PM5 3625 232270260102 RST SM 0603 RC21 1K PM5 3626 232270260102 RST SM 0603 RC21 1K PM5 3627 232270260473 RST SM 0603 RC21 47K PM5 3628 232270260473 RST SM 0603 RC21 47K PM5 3629 232270260473 RST SM 0603 RC21 47K PM5 3631 212211805667 RST SM 0603 RC0603 6K8 PM5 3634 212211805642 RST SM 0603 RC0603 75R PM5 3635 212211805642 RST SM 0603 RC0603 75R PM5 3636 212211805642 RST SM 0603 RC0603 75R PM5 3637 232270461002 RST SM 0603 RC22H 1K PM1 3638 232270461002 RST SM 0603 RC22H 1K PM1 3651 212211805976 RST SM 0603 RC0603 3K PM5 3652 232270461002 RST SM 0603 RC22H 1K PM1 3653 212211805669 RST SM 0603 RC0603 10K PM5 3654 212211805669 RST SM 0603 RC0603 10K PM5 3679 213810500082 RST MOX 1W RSS S 0R82 PM5 3681 232270260472 RST SM 0603 RC21 4K7 PM5 3682 212211805635 RST SM 0603 RC0603 10R PM5 3683 232270260101 RST SM 0603 RC21 100R PM5 3684 232270260472 RST SM 0603 RC21 4K7 PM5 3685 232270260102 RST SM 0603 RC21 1K PM5 3686 213811201111 RST SM 0805 RC05 110R PM5 3687 212211805639 RST SM 0603 RC0603 47R PM5 3701 212211805639 RST SM 0603 RC0603 47R PM5 3702 232270260279 RST SM 0603 RC21 27R PM5 3703 232270260279 RST SM 0603 RC21 27R PM5 3704 212211805639 RST SM 0603 RC0603 47R PM5 3705 232270260102 RST SM 0603 RC21 1K PM5 3706 232270260279 RST SM 0603 RC21 27R PM5 3707 212211805642 RST SM 0603 RC0603 75R PM5 3708 212211805639 RST SM 0603 RC0603 47R PM5 3709 212211805642 RST SM 0603 RC0603 75R PM5 3710 212211805642 RST SM 0603 RC0603 75R PM5 3711 232270260102 RST SM 0603 RC21 1K PM5 3712 232270260273 RST SM 0603 RC21 27K PM5 3714 232270260102 RST SM 0603 RC21 1K PM5 3715 232270260273 RST SM 0603 RC21 27K PM5 3718 212211805642 RST SM 0603 RC0603 75R PM5 3721 232270260101 RST SM 0603 RC21 100R PM5 3723 232270260101 RST SM 0603 RC21 100R PM5 3724 232270260224 RST SM 0603 RC21 220K PM5 3725 232270260224 RST SM 0603 RC21 220K PM5 3727 232270260102 RST SM 0603 RC21 1K PM5 3728 232270260102 RST SM 0603 RC21 1K PM5 3729 232270260273 RST SM 0603 RC21 27K PM5 3730 232270260273 RST SM 0603 RC21 27K PM5 3741 212211805639 RST SM 0603 RC0603 47R PM5 3742 212211805639 RST SM 0603 RC0603 47R PM5 3743 212211805639 RST SM 0603 RC0603 47R PM5 3744 232270260681 RST SM 0603 RC21 680R PM5 3745 232270260511 RST SM 0603 RC21 510R PM5 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 69 Go to cover page BDL3221 LCD/TV Spare Parts List 3746 212211805639 RST SM 0603 RC0603 47R PM5 3747 232270260332 RST SM 0603 RC21 3K3 PM5 3748 212211805639 RST SM 0603 RC0603 47R PM5 3749 232270260101 RST SM 0603 RC21 100R PM5 3751 232270260101 RST SM 0603 RC21 100R PM5 3752 232270260472 RST SM 0603 RC21 4K7 PM5 3753 232270260472 RST SM 0603 RC21 4K7 PM5 3754 232270260472 RST SM 0603 RC21 4K7 PM5 3755 232270260101 RST SM 0603 RC21 100R PM5 3756 232270260101 RST SM 0603 RC21 100R PM5 3757 235003510101 RST NETW SM ARV24 4X100R PM5 3758 235003510101 RST NETW SM ARV24 4X100R PM5 3781 232270260472 RST SM 0603 RC21 4K7 PM5 3782 232270260472 RST SM 0603 RC21 4K7 PM5 3783 212261200066 NTC DC TTC-103 S 10K PM5 3784 232270260102 RST SM 0603 RC21 1K PM5 3785 212211805642 RST SM 0603 RC0603 75R PM5 3786 232270260243 RST SM 0603 RC21 24K PM5 3787 232270260472 RST SM 0603 RC21 4K7 PM5 3788 232270260472 RST SM 0603 RC21 4K7 PM5 3789 232270260101 RST SM 0603 RC21 100R PM5 3791 232270260101 RST SM 0603 RC21 100R PM5 3792 212211805645 RST SM 0603 RC0603 150R PM5 3793 212211805645 RST SM 0603 RC0603 150R PM5 3794 212211805645 RST SM 0603 RC0603 150R PM5 3795 212211805659 RST SM 0603 RC0603 1K8 PM5 3796 212211805659 RST SM 0603 RC0603 1K8 PM5 3797 212211805659 RST SM 0603 RC0603 1K8 PM5 3801 212211805635 RST SM 0603 RC0603 10R PM5 3802 232270260472 RST SM 0603 RC21 4K7 PM5 3804 232270260101 RST SM 0603 RC21 100R PM5 3806 232270260101 RST SM 0603 RC21 100R PM5 3807 232270260101 RST SM 0603 RC21 100R PM5 3808 232270260472 RST SM 0603 RC21 4K7 PM5 3811 235003510689 RST NETW SM ARV24 4X 68R PM5 3812 235003510689 RST NETW SM ARV24 4X 68R PM5 3813 235003510689 RST NETW SM ARV24 4X 68R PM5 3814 235003510689 RST NETW SM ARV24 4X 68R PM5 3815 235003510229 RST NETW SM ARV24 4X 22R PM5 3816 235003510229 RST NETW SM ARV24 4X 22R PM5 3852 232270461005 RST SM 0603 RC22H 1M PM1 3853 232270260101 RST SM 0603 RC21 100R PM5 3854 232270260332 RST SM 0603 RC21 3K3 PM5 3855 232270260472 RST SM 0603 RC21 4K7 PM5 3856 232270260472 RST SM 0603 RC21 4K7 PM5 3857 232270260332 RST SM 0603 RC21 3K3 PM5 3858 232270260101 RST SM 0603 RC21 100R PM5 3859 232270260472 RST SM 0603 RC21 4K7 PM5 3860 232270260332 RST SM 0603 RC21 3K3 PM5 3862 232270260472 RST SM 0603 RC21 4K7 PM5 3865 232270260472 RST SM 0603 RC21 4K7 PM5 3867 232270260473 RST SM 0603 RC21 47K PM5 3869 232270260473 RST SM 0603 RC21 47K PM5 3872 232270260472 RST SM 0603 RC21 4K7 PM5 3873 232270260332 RST SM 0603 RC21 3K3 PM5 3874 232270260332 RST SM 0603 RC21 3K3 PM5 3875 232270260101 RST SM 0603 RC21 100R PM5 3884 212211805647 RST SM 0603 RC0603 220R PM5 3885 212211805647 RST SM 0603 RC0603 220R PM5 3886 212211805647 RST SM 0603 RC0603 220R PM5 3887 212211805647 RST SM 0603 RC0603 220R PM5 3888 232270260332 RST SM 0603 RC21 3K3 PM5 3889 232270260332 RST SM 0603 RC21 3K3 PM5 3891 232270260101 RST SM 0603 RC21 100R PM5 3892 232270260471 RST SM 0603 RC21 470R PM5 3893 232270260101 RST SM 0603 RC21 100R PM5 3901 212211805669 RST SM 0603 RC0603 10K PM5 3902 232270260223 RST SM 0603 RC21 22K PM5 3903 212211805669 RST SM 0603 RC0603 10K PM5 3904 232270260223 RST SM 0603 RC21 22K PM5 3905 232270260223 RST SM 0603 RC21 22K PM5 3906 232270260332 RST SM 0603 RC21 3K3 PM5 3907 232270260223 RST SM 0603 RC21 22K PM5 3908 232270260332 RST SM 0603 RC21 3K3 PM5 3909 212211805639 RST SM 0603 RC0603 47R PM5 3911 212211805944 RST SM 0603 RC0603 120K PM5 3912 212211805667 RST SM 0603 RC0603 6K8 PM5 3914 212211805667 RST SM 0603 RC0603 6K8 PM5 3915 232270260472 RST SM 0603 RC21 4K7 PM5 4101 232270296001 RST SM 0603 JUMP. MAX 0R05 4102 232270296001 RST SM 0603 JUMP. MAX 0R05 4103 232270296001 RST SM 0603 JUMP. MAX 0R05 4104 232270296001 RST SM 0603 JUMP. MAX 0R05 4105 232270296001 RST SM 0603 JUMP. MAX 0R05 4161 232270296001 RST SM 0603 JUMP. MAX 0R05 4162 232270296001 RST SM 0603 JUMP. MAX 0R05 4163 232270296001 RST SM 0603 JUMP. MAX 0R05 4164 232270296001 RST SM 0603 JUMP. MAX 0R05 4168 232270296001 RST SM 0603 JUMP. MAX 0R05 4174 232270296001 RST SM 0603 JUMP. MAX 0R05 4402 232270296001 RST SM 0603 JUMP. MAX 0R05 4601 232270296001 RST SM 0603 JUMP. MAX 0R05 4652 232270296001 RST SM 0603 JUMP. MAX 0R05 4654 232270296001 RST SM 0603 JUMP. MAX 0R05 4657 232270296001 RST SM 0603 JUMP. MAX 0R05 4659 232270296001 RST SM 0603 JUMP. MAX 0R05 4701 232270296001 RST SM 0603 JUMP. MAX 0R05 4702 232270296001 RST SM 0603 JUMP. MAX 0R05 4703 232270296001 RST SM 0603 JUMP. MAX 0R05 4801 232270296001 RST SM 0603 JUMP. MAX 0R05 4804 232270296001 RST SM 0603 JUMP. MAX 0R05 4805 232270296001 RST SM 0603 JUMP. MAX 0R05 4811 232270296001 RST SM 0603 JUMP. MAX 0R05 4812 232270296001 RST SM 0603 JUMP. MAX 0R05 4813 232270296001 RST SM 0603 JUMP. MAX 0R05 4814 232270296001 RST SM 0603 JUMP. MAX 0R05 4815 232270296001 RST SM 0603 JUMP. MAX 0R05 4851 232270296001 RST SM 0603 JUMP. MAX 0R05 4854 232270296001 RST SM 0603 JUMP. MAX 0R05 4855 232270296001 RST SM 0603 JUMP. MAX 0R05 4856 235003591001 RST NETW SM ARV24 4X JUMPER 4857 232270296001 RST SM 0603 JUMP. MAX 0R05 4858 232270296001 RST SM 0603 JUMP. MAX 0R05 4901 232270296001 RST SM 0603 JUMP. MAX 0R05 4903 232270296001 RST SM 0603 JUMP. MAX 0R05 5001 313818875771 COI CHOKE 35UH 82M OHM DR10X 5003 313818875771 COI CHOKE 35UH 82M OHM DR10X 5004 242254945579 IND FXD 1206 EMI 100MHZ 100R 5005 313818875771 COI CHOKE 35UH 82M OHM DR10X 5006 313818875771 COI CHOKE 35UH 82M OHM DR10X 5007 242254945579 IND FXD 1206 EMI 100MHZ 100R 5101 242253595853 IND FXD SM 0603 0U10 PM10 5102 242253595853 IND FXD SM 0603 0U10 PM10 5161 242254945579 IND FXD 1206 EMI 100MHZ 100R 5201 242254900449 IND FXD 0805 EMI 100MHZ 200R 5202 242254900449 IND FXD 0805 EMI 100MHZ 200R 5203 242254900449 IND FXD 0805 EMI 100MHZ 200R 5401 242254944197 IND FXD 0805 EMI 100MHZ 220R 5402 242254944197 IND FXD 0805 EMI 100MHZ 220R 5403 242254944197 IND FXD 0805 EMI 100MHZ 220R 5404 242254944197 IND FXD 0805 EMI 100MHZ 220R 5405 242254944197 IND FXD 0805 EMI 100MHZ 220R 5406 242254944197 IND FXD 0805 EMI 100MHZ 220R 5407 242254944197 IND FXD 0805 EMI 100MHZ 220R 5408 242254944197 IND FXD 0805 EMI 100MHZ 220R 5409 242254944197 IND FXD 0805 EMI 100MHZ 220R 5410 242254944197 IND FXD 0805 EMI 100MHZ 220R 5471 242254900449 IND FXD 0805 EMI 100MHZ 200R 5601 242253595853 IND FXD SM 0603 0U10 PM10 5602 242253595853 IND FXD SM 0603 0U10 PM10 5603 242253595853 IND FXD SM 0603 0U10 PM10 5604 242253595853 IND FXD SM 0603 0U10 PM10 5605 242253595853 IND FXD SM 0603 0U10 PM10 5607 242254900442 IND FXD 0603 EMI 100MHZ 600R 5701 242253595853 IND FXD SM 0603 0U10 PM10 5702 242253595853 IND FXD SM 0603 0U10 PM10 5704 242253595853 IND FXD SM 0603 0U10 PM10 5705 242253595853 IND FXD SM 0603 0U10 PM10 5706 242253595853 IND FXD SM 0603 0U10 PM10 5707 242253595853 IND FXD SM 0603 0U10 PM10 5741 242254900449 IND FXD 0805 EMI 100MHZ 200R 5742 242254900442 IND FXD 0603 EMI 100MHZ 600R 5743 242254900442 IND FXD 0603 EMI 100MHZ 600R 5744 242254900442 IND FXD 0603 EMI 100MHZ 600R 5745 242254900442 IND FXD 0603 EMI 100MHZ 600R 5746 242254900442 IND FXD 0603 EMI 100MHZ 600R 5781 242254944197 IND FXD 0805 EMI 100MHZ 220R 5782 242253595853 IND FXD SM 0603 0U10 PM10 5783 242253595853 IND FXD SM 0603 0U10 PM10 5784 242253595853 IND FXD SM 0603 0U10 PM10 5801 242254944197 IND FXD 0805 EMI 100MHZ 220R 5802 242254944197 IND FXD 0805 EMI 100MHZ 220R 5803 242254944197 IND FXD 0805 EMI 100MHZ 220R 5804 242254944197 IND FXD 0805 EMI 100MHZ 220R 5851 242254944197 IND FXD 0805 EMI 100MHZ 220R 5852 242254944197 IND FXD 0805 EMI 100MHZ 220R 5901 242254900126 IND FXD 0805 EMI 100MHZ 120R 5903 243853598058 IND FXD BEAD EMI 100MHZ 80R 5904 242253595853 IND FXD SM 0603 0U10 PM10 5905 242253595853 IND FXD SM 0603 0U10 PM10 5906 242253600782 IND FXD TSL0808 S 33U PM10 5907 242254900126 IND FXD 0805 EMI 100MHZ 120R 5908 242254900126 IND FXD 0805 EMI 100MHZ 120R 5909 242253600782 IND FXD TSL0808 S 33U PM10 5911 242254900126 IND FXD 0805 EMI 100MHZ 120R 5912 242254900126 IND FXD 0805 EMI 100MHZ 120R 5913 242253600782 IND FXD TSL0808 S 33U PM10 5914 242253600782 IND FXD TSL0808 S 33U PM10 5915 242254900126 IND FXD 0805 EMI 100MHZ 120R 6001 932221745685 DIO REC SM SSA34-E3 (VISH) 6003 932208282668 DIO REC SM SS34-E3 (VISH) 6004 932221745685 DIO REC SM SSA34-E3 (VISH) 6005 932221745685 DIO REC SM SSA34-E3 (VISH) 6007 933913910115 DIO SIG SM BAS32L (PHSE) 6101 933913910115 DIO SIG SM BAS32L (PHSE) 6202 933913910115 DIO SIG SM BAS32L (PHSE) 6203 933913910115 DIO SIG SM BAS32L (PHSE) 6301 933913910115 DIO SIG SM BAS32L (PHSE) 6302 933913910115 DIO SIG SM BAS32L (PHSE) 6701 932205042685 DIO SIG SM BAV99LG (ONSE) 7001 932211529668 FET POW SM SI9433DY-E3 (VISH 7002 932219076668 IC SM L5972D (ST00) 7004 932219076668 IC SM L5972D (ST00) 7005 932218295668 IC SM LD1117S (ST00) 7006 932213067676 IC L78L08ACZ (ST00) 7007 933967270685 TRA SIG SM BC847CLG (ONSE) 7008 933967270685 TRA SIG SM BC847CLG (ONSE) 7010 932219076668 IC SM L5972D (ST00) 7012 932219076668 IC SM L5972D (ST00) 7013 932217440685 TRA SIG SM KRC102S (KEC0) 7016 932217440685 TRA SIG SM KRC102S (KEC0) 7101 932217440685 TRA SIG SM KRC102S (KEC0) 7102 932217440685 TRA SIG SM KRC102S (KEC0) 7103 932217891668 IC SM M74HC4052RM (ST00) 7104 823827718301 AUDIO-DECORDER MSP3450G 7161 932219513668 IC SM M74HC590M (ST00) 7162 932215366668 IC SM CY7C199-15ZC (CYPR) 7163 932219513668 IC SM M74HC590M (ST00) 7164 935187000118 IC SM 74HC573PW (PHSE) 7165 933828890215 TRA SIG SM PMBT2369 (PHSE) 7166 935187000118 IC SM 74HC573PW (PHSE) 7201 935245720165 IC SM 74HCT1G14GW (PHSE) 7202 932214526668 IC SM M24C02-WMN6 (ST00) 7301 932214526668 IC SM M24C02-WMN6 (ST00) 7401 932222077668 IC SM AME1117ECGTZ (AME0) 7402 932222076668 IC SM AME1117CCGTZ (AME0) 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 70 Go to cover page BDL3221 LCD/TV Spare Parts List 7403 932222593671 IC SM MST5151A-LF (MSTA) 7404 932222075668 IC SM AME1117BCGTZ (AME0) 7471 823827716361 MEMORY IC 7601 933967270685 TRA SIG SM BC847CLG (ONSE) 7602 932220138668 IC SM AD8187ARU (ANA0) 7605 935260739118 IC SM 74LVC14APW (PHSE) 7651 932220869668 IC SM DS14C232CM (NSC0) 7653 932218295668 IC SM LD1117S (ST00) 7654 932217440685 TRA SIG SM KRC102S (KEC0) 7655 932217440685 TRA SIG SM KRC102S (KEC0) 7676 933967310685 TRA SIG SM BC848CLG (ONSE) 7701 933967270685 TRA SIG SM BC847CLG (ONSE) 7741 935276561518 IC SM SAA7119E/V2/G (PHSE) 7742 932222076668 IC SM AME1117CCGTZ (AME0) 7743 932222077668 IC SM AME1117ECGTZ (AME0) 7781 935275732112 IC SAA5264PS/M3/1437 (PHSE) 7782 933967310685 TRA SIG SM BC848CLG (ONSE) 7801 932220476671 IC SM T6TU5XBG-0001(O2) 7802 823827716781 1M16-42S16100A1 7852 932219183685 IC SM LM809M3-2.93 NOPB(NSC0 7853 933967270685 TRA SIG SM BC847CLG (ONSE) 7855 932222010682 IC SM NT68F632ALG (NOVA) 7858 932212209682 IC M24C32-WBN6P (ST00) 7901 935273874115 IC SM TDA1308T/N2 (PHSE) 7902 932222037668 IC SM TPA3008D2PHP (TI00) PCB Assy 1058 313815864611 POWER PCB ASSY - BDS 32" 2051 202233000078 CAP MPP 275V S 470N PM10 2052 202055490156 CERSAF CD 250V S 1N PM20 2053 202055490156 CERSAF CD 250V S 1N PM20 2054 202233000078 CAP MPP 275V S 470N PM10 2055 823827718501 1.5MF 450V MPP 2056 222291019856 CER2 0805 Y5V 25V 330N P8020 2057 222224119876 CER2 1206 Y5V 10V 10U P8020 2058 223858015636 CER2 0805 X7R 50V 10N PM10 2059 223891015649 CER2 0805 X7R 25V 100N PM10 2060 202203100426 ELCAP HS 450V S 120U PM20 2061 202055790153 CER2 DC B 500V S 2N2 PM10 2062 242254900673 SURGE PROTECT SPG-201M-A 2063 242254900673 SURGE PROTECT SPG-201M-A 2064 242254900673 SURGE PROTECT SPG-201M-A 2065 223858015643 CER2 0805 X7R 50V 33N PM10 2066 203803521302 ELCAP GS 25V S 4U7 PM20 2067 203803521307 ELCAP GS 25V S 68U PM20 2068 202203100272 ELCAP PF 25V S 47U PM20 2069 242254900673 SURGE PROTECT SPG-201M-A 2070 223891015649 CER2 0805 X7R 25V 100N PM10 2071 202055490158 CERSAF CD 250V S 2N2 PM20 2072 223858015627 CER2 0805 X7R 50V 2N2 PM10 2073 203830150151 CAP PP PPN 100V S 10N PM2 2074 202203100387 ELCAP EB 25V S 2200U PM20 2075 202203100273 ELCAP PF 25V S 100U PM20 2076 223858015649 CER2 0805 X7R 50V 100N PM10 2077 203830150191 CAP PP PPN 100V S 3N3 PM2 2078 203830150159 CAP PP PPN 100V S 12N PM5 2079 202203100428 ELCAP GF 35V S 1000U PM20 2080 202203100428 ELCAP GF 35V S 1000U PM20 2081 203803527502 ELCAP KM 50V S 22U PM20 2085 223858015625 CER2 0805 X7R 50V 1N5 PM10 2086 202202000805 ELCAP GS 50V S 2U2 PM20 2087 223858015636 CER2 0805 X7R 50V 10N PM10 2088 223891015649 CER2 0805 X7R 25V 100N PM10 2091 223891015649 CER2 0805 X7R 25V 100N PM10 2092 223891015649 CER2 0805 X7R 25V 100N PM10 3051 212211805971 RST SM 1206 RC1206 270K PM5 3052 212211805971 RST SM 1206 RC1206 270K PM5 3053 212211805971 RST SM 1206 RC1206 270K PM5 3054 232271161824 RST SM 1206 RC01 820K PM5 3055 232271161824 RST SM 1206 RC01 820K PM5 3056 213811201822 RST SM 0805 RC05 8K2 PM5 3057 232273061333 RST SM 0805 RC11 33K PM5 3058 212210101515 RST CRB CF1/6 A 390R PM5 3059 212010500027 RST MOX 1W RSS A 0R15 PM1 3060 232271161333 RST SM 1206 RC01 33K PM5 3061 213810113228 RST CRB CFR-12 A 2R2 PM5 3062 232273061689 RST SM 0805 RC11 68R PM5 3063 232271161108 RST SM 1206 RC01 1R PM5 3064 232273463304 RST SM 0805 RC12H 330K PM1 3065 232273463304 RST SM 0805 RC12H 330K PM1 3066 232273463304 RST SM 0805 RC12H 330K PM1 3067 232273466201 RST SM 0805 RC12H 620R PM1 3068 232273465602 RST SM 0805 RC12H 5K6 PM1 3069 212255000184 VDR DC 1MA/510V S MAX 845V 3070 232273061102 RST SM 0805 RC11 1K PM5 3071 212261200074 NTC DC SCK-034 S 3R PM15 3072 823827718171 VDR DC 1MA/510 845V R 3073 213811201105 RST SM 0805 RC05 1M PM5 3074 213811201224 RST SM 0805 RC05 220K PM5 3075 232273061102 RST SM 0805 RC11 1K PM5 3076 232273061471 RST SM 0805 RC11 470R PM5 3077 232273061274 RST SM 0805 RC11 270K PM5 3078 232273061474 RST SM 0805 RC11 470K PM5 3079 213811201331 RST SM 0805 RC05 330R PM5 3080 213811201103 RST SM 0805 RC05 10K PM5 3081 212010500027 RST MOX 1W RSS A 0R15 PM1 3082 213811201151 RST SM 0805 RC05 150R PM5 3083 213810113228 RST CRB CFR-12 A 2R2 PM5 3084 213811201222 RST SM 0805 RC05 2K2 PM5 3085 232273061102 RST SM 0805 RC11 1K PM5 3086 213811201152 RST SM 0805 RC05 1K5 PM5 3087 213810113334 RST CRB CFR-12 A 330K PM5 3088 232273061229 RST SM 0805 RC11 22R PM5 3089 213811201222 RST SM 0805 RC05 2K2 PM5 3090 232273461002 RST SM 0805 RC12H 1K PM1 3091 232273461803 RST SM 0805 RC12H 18K PM1 3092 213811201101 RST SM 0805 RC05 100R PM5 3093 212210102197 RST CRB CF1/6 A 4K7 PM5 3094 232273061223 RST SM 0805 RC11 22K PM5 3095 232273462202 RST SM 0805 RC12H 2K2 PM1 3096 232273061223 RST SM 0805 RC11 22K PM5 3097 232273061223 RST SM 0805 RC11 22K PM5 3098 213811201103 RST SM 0805 RC05 10K PM5 5051 242254900499 FIL MAINS 6MH 1A8 S42010 5052 243853598026 IND FXD BEAD EMI 100MHZ 35R 5053 243853598026 IND FXD BEAD EMI 100MHZ 35R 5054 242254900498 FIL MAINS 5MH 2A S4103 5055 242254900497 FIL PFC 430UH 0R19 S4084 5056 313816875411 BEAD 5057 313816875411 BEAD 5058 243853598026 IND FXD BEAD EMI 100MHZ 35R 5059 313816875411 BEAD 5060 313816875411 BEAD 5061 242253597072 IND FXD SP0305 A 6U8 PM10 5071 242254900503 TFM SMT LAYER HJC-S4143 WIRE 5072 243853598026 IND FXD BEAD EMI 100MHZ 35R 5073 243853598026 IND FXD BEAD EMI 100MHZ 35R 5074 242253601187 IND FXD OL1028H S 15U PM10 5075 243853598026 IND FXD BEAD EMI 100MHZ 35R 5076 243853598026 IND FXD BEAD EMI 100MHZ 35R 5077 243853598026 IND FXD BEAD EMI 100MHZ 35R 5078 243853598026 IND FXD BEAD EMI 100MHZ 35R 5079 242253601102 IND FXD OL1028H S 10U PM10 5080 242253601187 IND FXD OL1028H S 15U PM10 6051 931900263671 BRIDGE GBU6J-E3 (VISH) 6052 932220958687 DIO REC STTH5L06FP (ST00) 6053 933952580685 DIO SIG SM BAV103 (VISH) 6055 932214069673 DIO SUP P6KE250A A (VISH) 6056 932222163673 DIO REC UF1007 A (LITO) 6061 933952580685 DIO SIG SM BAV103 (VISH) 6062 933952580685 DIO SIG SM BAV103 (VISH) 6063 933952580685 DIO SIG SM BAV103 (VISH) 6064 933751660673 DIO REC RGP10D-E3 A (VISH) 6065 933952580685 DIO SIG SM BAV103 (VISH) 6066 933751660673 DIO REC RGP10D-E3 A (VISH) 6067 932222228673 DIO SUP P4KE16A-E3 (VISH) 6071 932219932687 DIO REC STPS10H100CFP (ST00) 6072 933952580685 DIO SIG SM BAV103 (VISH) 6073 933952580685 DIO SIG SM BAV103 (VISH) 6074 933117810133 DIO REG BZX79-C12 A (PHSE) 6075 933712760673 DIO REG BZX55-B18 A (VISH) 6076 932219203687 DIO REC STPS20H100CFP (ST00) 6081 933712970673 DIO REG BZX55-C20 A (VISH) 7056 932222284682 IC L6562N (ST00) 7057 932217923687 FET POW STP20NM60 (ST00) 7061 935267356112 IC TEA1507P/N1 (PHSE) 7062 932219657687 FET POW STP10NK80ZFP (ST00) 7063 933953410676 TRA SIG TBC328-40 (TOSJ) 7071 932217439685 TRA SIG SM BC857C (KEC0) 7072 932214014667 OPT CP TCET1103(G) (VISH) 7073 932208697676 IC TL431ACZ S (ST00) 7074 932214014667 OPT CP TCET1103(G) (VISH) 7075 933705890676 TRA SIG BF422 (TOSJ) 7076 933237790126 TRA SIG BC547C (PHSE) PCB Assy 1053 313815862301 DSUB ADAPOTOR PCB ASSY 2699 222224119876 CER2 1206 Y5V 10V 10U P8020 PCB Assy 1055 313815863541 CONTROL PCB ASSY 2091 223858615636 CER2 0603 X7R 50V 10N PM10 2093 223858619805 CER2 0603 Y5V 50V 10N P8020 2094 223858619805 CER2 0603 Y5V 50V 10N P8020 3086 232270260101 RST SM 0603 RC21 100R PM5 3087 232270260512 RST SM 0603 RC21 5K1 PM5 3088 212211805662 RST SM 0603 RC0603 2K7 PM5 3089 232270260122 RST SM 0603 RC21 1K2 PM5 3091 212211805669 RST SM 0603 RC0603 10K PM5 PCB Assy 1056 313815863551 IR PCB ASSY 2071 223858619812 CER2 0603 Y5V 50V 100N P8020 2072 223858619812 CER2 0603 Y5V 50V 100N P8020 3071 232270260152 RST SM 0603 RC21 1K5 PM5 3072 232270260472 RST SM 0603 RC21 4K7 PM5 3073 212211805647 RST SM 0603 RC0603 220R PM5 3074 212211805647 RST SM 0603 RC0603 220R PM5 6071 932219711682 OPT SEN L-97DSP7C (KIEL) 6072 932219382682 LED VS L-3WSYKPBW (KIEL) 6073 932220313667 IR RECEIVER TSOP34136SB1 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 71 Go to cover page BDL3221 LCD/TV Recommended Parts List Recommended Parts List TYPE:BDL3221V/00 7 313815760051 BASE ASSY 30 313815760041 FRONT BEZEL ASSY(B) 31 313815161951 FRONT BEZEL 32 313815416701 FRONT CORNER-B/R(BLACK) 33 313815416691 FRONT CORNER-T/R(BLACK) 34 313815410821 LENS 37 313815321431 RUBBER STRIP 38 313815321441 RUBBER-650X15X2 39 313815321451 RUBBER - 360X15X2 40 313815760441 BACK COVER ASSY 41 313815137491 BACK COVER 42 313815410812 CONTROL BOTTON 44 313815416431 HANDLE CLIP 46 313815137431 HANDLE HOLDER 47 313815137421 HANDLE 60 313815137501 BOTTOM MAIN FRAME 91 313815137571 TV COVER 93 313815137511 SHIELDING -SCALER RIGHT 94 313815137521 SHIELDING -SCALER BOTTOM 95 313815137531 METAL BLOCK-GAP 126 313815567771 RATING LABEL 145 313811708821 E-D.F.U.(32") 221 313815137381 TV HOUSING 291 313815567691 LABEL(LG-WE) 292 313815567691 LABEL(LG-WE) 452 313815640741 BOTTOM SLIP BOARD 455 313815640731 P.E. BAG 456 313815640751 CARTON 457 313815640701 CUSHION-TOP 458 313815640711 CUSHION-BTM 464 314105631521 SMALL PLASTIC HANDLE 615 313811708611 HEX CODE OF F/W(NO MATL REQ) 1176 313923811281 PROD ASSY RC1124134/01 PKD 7001 932211529668 FET POW SM SI9433DY-E3 (VISH 7002 932219076668 IC SM L5972D (ST00) 7007 933967270685 TRA SIG SM BC847CLG (ONSE) 7013 932217440685 TRA SIG SM KRC102S (KEC0) 7056 932222284682 IC L6562N (ST00) 7057 932217923687 FET POW STP20NM60 (ST00) 7072 932214014667 OPT CP TCET1103(G) (VISH) 7073 932208697676 IC TL431ACZ S (ST00) 7074 932214014667 OPT CP TCET1103(G) (VISH) 7162 932215366668 IC SM CY7C199-15ZC (CYPR) 7202 932214526668 IC SM M24C02-WMN6 (ST00) 7403 932222593671 IC SM MST5151A-LF (MSTA) 7676 933967310685 TRA SIG SM BC848CLG (ONSE) 7743 932222077668 IC SM AME1117ECGTZ (AME0) 7801 932220476671 IC SM T6TU5XBG-0001(O2) 7802 823827716781 1M16-42S16100A1 7852 932219183685 IC SM LM809M3-2.93 NOPB(NSC0 7855 932222010682 IC SM NT68F632ALG (NOVA) 7902 932222037668 IC SM TPA3008D2PHP (TI00) 8055 313819876161 CBLE-390 10/160/10-020 AWG26 8152 313819876122 CBLE-019 9/130/9-019 AWG28 8174 313819876151 CBLE-130 30/270/30-033 AWG28 8175 313819876191 CBLE-392 12/620+200/12-022 8177 313819876171 CBLE-014 4/420/4-014 AWG28 8178 313819876181 CBLE-016 6/480/6-016 AWG28 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 72 BDL3221 LCD/TV Go to cover page 32 1 GENERAL PRODUCT SPECIFICATION GENERAL PRODUCT SPECIFICATION . 32" Multifunction LCD monitor . PC 15 pins D-SUB analog interface . PC audio line in with mini-Jack . TV Tuner, S-Video, RCA AV input/output interface with R/L Audio-in . SCART interface . DVI digital interface with HDCP support (for TV and PC) . HD/Component YPbPr with L/R audio input (RCA connector) . NTSC, PAL,SECAM TV color system . PC graphic auto picture adjustment . 12 user modes . User-friendly OSD menu . User-friendly remote controller . Recommend resolution 1366 x 768 non-interlace at 60 Hz . WXGA 32" color TFT LCD flat panel . Anti-glare to reduce light reflection . Power management capability . VESA standard wall mount kit (option) BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 73 Go to cover page 2 32 GENERAL PRODUCT SPECIFICATION(Continued) CONTENTS 1.0 Foreword 2.0 Product profile 2.1 LCD 2.2 Scanning frequencies 2.3 Video dot rate 2.4 Power input 2.5 Power consumption 2.6 Dimensions 2.7 Weight 2.8 Side speaker 2.9 Functions 2.10 Ambient temperature 2.11 Regulatory compliance 3.0 Electrical characteristics 3.1 Interface signals cables 3.2 User interface 3.2.1 Front and rear control panel 3.2.2 Front and rear control panel definition 3.2.3 Remote control 3.2.4 OSD Menu 3.2.5 RS232 control 3.3 PC, TV requirement 3.3.1 PC interface 3.3.1.1 Mode storing capacity 3.3.1.2 Horizontal scanning 3.3.1.3 Vertical scanning 3.3.1.4 Input connectors 3.3.1.5 Available timings 3.3.2 I/O interface 3.3.3 TV interface 3.3.3.1 TV Tuner 3.3.3.2 Deviation of TV system 3.3.3.3 TV color setting 3.3.3.4 TV audio setting 3.3.3.5 TV special setting 3.3.4 Electric characteristics of I/O 3.3.4.1 PC Signal type 3.3.4.2 TV Signal type 3.3.4.3 CVBS output 3.3.4.4 Headphone output 3.3.5 Picture in picture 3.3.5.1 Display function 3.3.5.2 Display size 3.3.5.3 Display location 3.3.5.4 Picture by picture 3.3.5.5 Zoom 3.4 Power input connection 3.5 Power management 4.0 Visual characteristics 4.1 Test conditions 4.2 PC resolution 4.3 Brightness 4.4 Image size 4.4.1 Actual display size 4.5 Brightness uniformity 4.6 PC white color adjustment 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 74 BDL3221 LCD/TV Go to cover page 32 3 GENERAL PRODUCT SPECIFICATION(Continued) 4.7 TV white color adjustment 4.8 TV picture centering 4.9 HD support timing 4.9.1 HD detail timing 5.0 Mechanical characteristics 5.1 Controls 5.2 Unit dimension / weight 5.3 Tilt and swivel base 5.4 Transportation packages 5.4.1 Shipping dimension / weight 5.4.2 Block unit / palletization 6.0 Environmental characteristics 6.1 Susceptibility of display to external environment 6.2 Transportation tests 6.3 Display disturbances from external environment 7.0 Reliability 7.1 Mean time between failures 8.0 Quality assurance requirements 8.1 Acceptance test 9.0 Serviceability 10.0 Appendices � Fig 1 Pattern 1 - Brightness and Uniformity Pattern 2 - Cross talk pattern - Gray leave 184 (256 gray level) Pattern 3 - Cross talk pattern - Center gray level 0 (Black) � Table 1 WE model: West Europe TV Preload channels � Table 2 NAFTA model: US - Air broadcast channels US - Cable channels � Table 3 AP model: AP multi TV preload channels � Table 4 China model: China TV preload channels BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 75 Go to cover page 4 32 GENERAL PRODUCT SPECIFICATION(Continued) 1.0 FOREWORD This specification describes a 32" multifunction LCD Monitor, maximum resolution up to 1366x768/60Hz non-interlaced. 2.0 PRODUCT PROFILE This 32" TFT LCD monitor/TV can connect to PC 's analog D-SUB and TV's digital signal through DVI-D connector and it also have TV, Composite Video, S-Video, Scart , PVR output and HD YPbPr interface. 2.1 LCD 2.1.1 LPL panel Type NO : LC320W01 A6K3 (Supplier LPL) Display area(mm) : 697.685mm x 392.256mm Number of Pixels : 1366(H) x 768(V) Pitch ( mm ) : 0.170mm(H) x 0.510mum(V) Color pixel arrangement : RGB vertical stripe Display operating mode : Normally black Color depth : 16,7M colors ( 8 bits) Brightness (cd/m^2) : 500(Center 1 points, Typ.) Viewing angle(CR>10) : Viewing angle free(R/L 178(Typ.),U/D 178(Typ.)) Surface treatment : Hard coating(3H),Anti-glare treatment of the front polarize Electrical interface : LVDS Response Time (ms, Typ) : TrR:8,TrD:10(Gray to Gray) Contrast ratio : Typical 1000 : 1 with AI Outline Dimension : 760 mm(H) x 450 mm(V) x 48(D) mm (Typ.) Module weight (g) : 7,200g(Typ.) Backlight : 20 EEFL 2.2 Scanning frequencies : Hor. : 45 - 50KHz Ver.: 47 - 63 Hz 2.3 Video dot rate : <80 MHz 2.4 Power input : 90 - 264 Vac, 50/60 � 2 Hz 2.5 Power consumption : 100W/Typ. ( at PC mode ) , 130 W/Typ. ( at TV mode ). 2.6 Unit Dimensions : 794 mm W x 517 mm H x 244 mm D (Incl. Pedestal, excl. speaker) Speaker dimensions : 110 mm W x 490 mm H x 70 mm D 2.7 Unit Weight : 19.17 kg (exclude speaker boxs , Incl. Pedestal) 2.8 Speakers & unit weight : 2 x 10 W (weight : 2.8 kg) 2.9 Functions : PC �15 pins D-sub analog interface with audio mini-Jack input (PC line in). �15 pins D-sub analog output �DVI-D Digital interface (support TV DVI HDCP input) TV �DVI-D Digital interface (Support HDCP) share with PC audio input. �Tuner, Aerial input. �HD/Component YPbPr input and audio input with RCA jack. �Composite video input and S-Video input share with the same audio. �Scart connector support RGB/S-video/ CVBS input and tuner CVBS output. �PVR output (Composite Video and Audio output). �Headphone output. 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 76 BDL3221 LCD/TV Go to cover page 32 5 GENERAL PRODUCT SPECIFICATION(Continued) Rear Control Panel UP / Channel + Left / Volume - Down / Channel - DC Power Switch Front Control Panel Input select Right / Volume + OSD IR receiver Power LED Light Sensor 2.10 Ambient temperat : 0 - 40 �C 2.11 Regulatory compliance : Safety requirement: CCC (China), CSA(Canada), IEC 950 CB Report, SEMKO(Nordic), UL(USA), PSB(Singapore) EMI requirement: C-tick, CE (Europe), FCC (USA), IC (Canada) 3.0 Electrical characteristics 3.1 Interface signals cables VGA Interface Cable Length : 1.8 M +/- 50 mm DVI-D Cable Length : 1.8 M +/- 50 mm Stereo RCA R/L audio cable (option) Length : 1.5 M +/- 50 mm S-video cable (option) Length : 1.5 M +/- 50 mm AV cable (option) Length : 1.5M +/- 50 mm SCART cable (option) Length : 1.5 M +/- 50 mm Mini Jack stereo cable (option) Length : 1.5 M +/- 50 mm YPbPr cable (option) Length : 1.5M +/- 50mm Power cord Length : 1.8 M +/- 50 mm 3.2 User interface On screen display user control via rear keypad and remote control for PC and TV OSD. 3.2.1 Front and Rear control panel BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 77 Go to cover page 6 32 GENERAL PRODUCT SPECIFICATION(Continued) 3.2.2 Front and Rear control panel definition: Front Power LED : Normal operation�Blue. Standby mode�Amber. IR receiver : Sense the signal from RC handset. Light Sensor : It will set the LCD back light brightness automatically according to the ambient light. Rear Input select : Input source select key PC � DVI� HDCP � TV�AV� S-VIDEO �EXT�HD and PC again. Up/Down : Channel up and down, and OSD cursor up and down. Left/Right : Volume up and down, and OSD cursor left and right. OSD : Enable OSD menu(Enter key for PC). Power SW : DC Power switch. Power SW : AC Power switch. 3.2.3 Remote control 3.2.3.1 The remote control is used in all PC and TV modes : I. Be a Monitor: 1. Press Menu Key to call Monitor Menu 2. Press Up/Down/Left/Right Key to select Monitor function 3. Left/Right is Volume Hot Key. 4. Use remote controller to select PC menu function. II. Be a TV: 1. Press Menu Key to display TV Menu 2. Press Up/Down/Left/Right Key to select TV function 3. Up/Down Key is Channel Hot Key. 4. Left/Right Key is Volume Hot Key. 5. Use remote controller to select TV menu function. III. Recalling from saving mode: In Monitor power saving mode, which no H&V sync, or no either H-sync or V-sync input via VGA connector. The monitor will enter "Monitor saving mode". The way to wake up Monitor 1. when PC H-sync and V-sync have signal again , then Monitor will wake up. 2. press "Source" key on remote control� change to Video source directly. In TV power saving mode, which switched off by RC "Standby" key, SLEEP TIMER function or no TV signal input for 30 minutes, the monitor will enter "TV standby mode", and LED shows amber color. The way to wake up Monitor 1. press . "Standby" key on remote control to return original Video source 2. press "Source" key on remote control� change to other Video source directly. Remark : 1. When TV is in saving mode (Amber LED), Power off by rear DC power switch key . 2. When DC re-power on, the set will still stay in saving mode(as previous mode) 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 78 BDL3221 LCD/TV Go to cover page 32 7 GENERAL PRODUCT SPECIFICATION(Continued) 3.2.3.2 Remote control key definition NAFTA model WE/AP/China Model 1.Power: Power On/Standby key 2.Sleep timer: 15,30,60,120,180,240 OFF 3.Display Format: Picture format with Wide screen/4:3/Zoom 16:9/Supper Wide 4. AV: Source selection 5.Numerica keys : (0~9) ,Channel setting 6.Previous : Return previous program 7.Menu: Main menu select 8.OK: Ok key 9. : Direction Left/ right for OSD and adjustment/VOL+/VOL- 10.PC/TV : Source change between PC and TV 11.Smart sound: Smart sound hot key 12.Smart picture: Smart picture hot key 13.CC: Closed caption on/off 14.^ / v : Direction up/down for OSD and adjustment/CH+/CH- 15.Freeze picture: Freeze picture function 16.I-II: (2nd audio) Sound select 17.Status OSD : Display OSD status 18.PIP size: PIP size selection 19.PIP position : PIP position hot key 20.Sound mute function 1 19 18 15 12 11 10 7 6 3 5 2 4 8 9 14 13 16 17 20 1.Power: Power On/Standby key 2.Sleep timer: 15,30,60,120,180,240 OFF 3.Display Format: Picture format with Wide screen/4:3/Zoom 16:9/Supper Wide 4. AV: Source selection 5.Numerica keys : (0~9) ,Channel setting 6.Previous : Return previous program 7.Menu: Main menu select 8.OK: Ok key 9. : Direction Left/ right for OSD and adjustment/VOL+/VOL- 10.PC/TV : Source change between PC and TV 11.Teletext Enlarge: Teletext Enlarge 12.Teletext Mix : Teletext Mix hot key 13.Teletext On/Off : Teletext On/Off hot key 14. Smart sound: Smart sound hot key 15.Smart picture: Smart picture hot key 16.Reveal/Conceal 17.Teletext OSD main Index 18.Teletext Hold 19.Teletext access 20. CC: Closed caption on/off (disable) 21. .^ / v : Direction up/down for OSD and adjustment/CH+/CH- 22. Status OSD : Display OSD status 23..I-II: (2nd audio) Sound select 24. Freeze picture: Freeze picture function 25. PIP size: PIP size selection 26 .PIP Position: PIP position hot key 27.Sound mute function 18 25 16 15 26 17 13 14 11 12 22 10 7 6 3 5 2 4 8 9 21 20 23 27 1 19 24 All PC or TV OSD menu function could be accomplished by remote control. BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 79 Go to cover page 8 32 GENERAL PRODUCT SPECIFICATION(Continued) 3.2.4 OSD Menu 3.2.4.1 PC Signal control: PICTURE SMART PICTURE FEATURES NORMAL PIP WARM SIZE COOL OFF PC MAIN MENU BRIGHTNESS SMALL CONTRAST MEDIUM AUTO ADJUST LARGE YES PBP STORE VIDEO YES TV NO AV MANUAL ADJUST S-VIDEO PHASE EXT CLOCK AUDIO HORIZONTAL PC VERTICAL PIP DISPLAY AUDIO ICON1 SMART SOUND ICON2 MUSIC SOURCE ICON3 THEATRE PC ICON4 NEWS DVI PERSONAL TV SETTINGS AV TREBLE S-VIDEO BASS HD BALANCE EXT VIRTUAL SURROUND ZOOM ON ZOOM ID OFF ZOOM TYPE AVL OFF YES 4X4 NO INSTALL 3X3 LANGUAGE 2X2 ENGLISH 1X5 DEUTSCH FRANÇ AIS ITALIANO ESPAÑ OL MONITOR ID DCR ON OFF LIGHT SENSOR ON OFF REMOTE CONTROL ON OFF FACTORY RESET NO YES 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 80 BDL3221 LCD/TV Go to cover page 32 9 GENERAL PRODUCT SPECIFICATION(Continued) 3.2.4.2 TV Signal control: WE /AP/China PICTURE INSTALL SMART PICTURE LANGUAGE SPORTS ENGLISH MOVIES DEUTSCH WEAK SIGNAL FRANÇ AIS TV MAIN MENU NIGHT ITALIANO MULTIMEDIA ESPAÑ OL PERSONAL BRIGHTNESS MONITOR ID CONTRAST DCR COLOR ON SHARPNESS OFF TINT LIGHT SENSOR AUDIO ON SMART SOUND OFF MUSIC REMOTE CONTROL THEATRE ON NEWS OFF PERSONAL FACTORY RESET SETTINGS NO TREBLE YES BASS BALANCE SETUP VIRTUAL SURROUND AUTO PROGRAM ON START OFF MANUAL STORE AVL SYSTEM YES FRANCE FEATURES NO WEST EUROPE SOURCE PC MANUAL STORE DVI HDCP PROGRAM NUMBER TV FINE TUNE AV STORE S-VIDEO YES HD STORE EXT YES NO PICTURE FORMAT CHANNEL SETTING AUTOMATIC CHANNEL EDIT 4:3 CHANNEL ZOOM 16:9 SKIP WIDESCREEN ACTIVATE SUPER WIDE SKIP PICTURE ALIGNMENT CHANNEL SWAP AUTO LOCK FROM LOCK PROGRAM TO CHANGE CODE EXCHANGE YES EXCHANGED CLEAR ALL ON NAME EDIT ZOOM OFF CHANNEL ZOOM ID NAME ZOOM TYPE OFF CHANNEL SORT 4X4 SORT 3X3 2X2 1X5 BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 81 Go to cover page 10 32 GENERAL PRODUCT SPECIFICATION(Continued) NAFTA model PICTURE SETUP SMART PICTURE TUNER MODE SPORTS ANTENNA BRIGHTNESS MOVIES CABLE CONTRAST WEAK SIGNAL AUTO TV MAIN MENU COLOR NIGHT AUTO PROGRAM SHARPNESS MULTIMEDIA START TINT PERSONAL CHANNEL EDIT AUDIO CHANNEL SMART SOUND MUSIC SKIP THEATRE ACTIVATE NEWS SKIP PERSONAL MANUAL FINE TUNE SETTINGS RATING TREBLE BLOCK OPTION BASS ON BALANCE OFF VIRTUAL SURROUND ON MOVIE RATING OFF G ON AVL YES OFF NO PG FEATURES PG13 SOURCE PC R DVI HDCP NC17 TV X AV S-VIDEO TV RATING HD TV Y EXT TV Y7 PICTURE FORMAT AUTOMATIC BLOCK 4:3 FV ZOOM 16:9 TV G WIDESCREEN TV PG SUPER WIDE BLOCK PICTURE ALIGNMENT V AUTO LOCK S LOCK PROGRAM L CHANGE CODE D YES TV 14 CLEAR ALL BLOCK ON V ZOOM OFF S ZOOM ID L ZOOM TYPE OFF D INSTALL 4X4 TV MA LANGUAGE ENGLISH 3X3 BLOCK DEUTSCH 2X2 V FRANÇ AIS 1X5 S ITALIANO L ESPANOL CLOSED CAPTION CAPTION MODE MONITOR ID CC1 DCR ON CC2 OFF CC3 LIGHT SENSOR ON CC4 OFF TXT1 REMOTE CONTROL ON TXT2 OFF TXT3 FACTORY RESET NO TXT4 YES CC MUTE CC DISPLAY ON OFF 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 82 BDL3221 LCD/TV Go to cover page 32 11 GENERAL PRODUCT SPECIFICATION(Continued) 3.2.4.3 OSD messages Message When Cannot Display This Video Mode, Change computer input to 1366x768 @ 60Hz �Dot Rate higher than 103MHz Horizontal frequency does not fall into between 30 and 61kHz � Vertical frequency does not fall between 56Hz and 75Hz (Non- Interlaced) �Resolution higher than 1366x768 No Video Input No video signal input as monitor power on. OSD attention signal Use 1366 x 768 for best Result. When input signal's resolution is below 1366 x 768 � Attention Signal off Above attention signals can be switched off by pressing "UP" and "DOWN" key together for more than 10 seconds if there is no video signal in. The Attention signal "Attention signals on" or "Attention signal off" appears for 3 seconds. 3.2.4.4 OSD Lock OSD function can be locked by � Pressing "Menu" button for more than 10 seconds while there is video signal in. The screen automatically shows OSD MAIN MENU LOCKED for 3 seconds. When users press "Menu" button, OSD Lock MENU will appear, and the default cursor location will be on unlock. � Using RS232 command. OSD can be unlocked by � Pressing front panel "Menu" button for more than 10 seconds while there is video signal in. As the menu button is pressed, the screen will keep showing OSD MAIN MENU LOCKED until OSD function unlocked. Then, OSD MAIN MENU UNLOCK will automatically show for 3 seconds. � Using RS232 command. 3.2.4.5 Hidden functions The following hidden functions are available for development and service personnel only, not for end customers. Function Description OSD lock / unlock Press "Menu" button for more than 10 seconds while there is video signal in. Factory Mode � To hold "Menu + DOWN" buttons, then Power on while there is video signal in. Monitor will exit factory mode automatically once power is off. � Press remote control code "062596", then press menu key. Switch on / off attention signals To press "UP" and "DOWN" key together for more than 10 seconds while is no video signal in. BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 83 Go to cover page 12 32 GENERAL PRODUCT SPECIFICATION(Continued) 3.2.5 RS232 Control 9 pin D-Sub connector, for RS232 interface with pin assignment as follows: The communication protocol divided into 5 groups. The simulation test program Can select necessary items to assure RS232 port function well. Group 1 (Geometry Group): HORIZONTAL POSITION VERTICAL POSITION SCREEN MODE VIDEO MODE PIP SIZE PIP POSITION Group 2 (Miscellaneous Group): STATUS OPERATION HOURS LIGHT SENSOR FACTORY RESET SLEEP TIMER CLOSED CAPTION TV SYSTEM CHANNEL SEARCH Group 3 (Picture Group) LANGUAGE BRIGHTNESS CONTRAST AUTO ADJUST PHASE PIXEL CLOCK COLOR SETTING RED COLOR GREEN COLOR BLUE COLOR VIDEO COLOR SHARPNESS TINT COLOR TEMPERATURE INPUT SELECT PIP VIDEO SOURCE Group 4 (Audio Group): SMART SOUND TREBLE BASS BALANCE VOLUME SURROUND MUTE Group 5 (Debug Group) PIN No. SIGNAL 1 Not used 2 MRXD 3 MTXD 4 Not used 5 GND 6 Not used 7 Not used 8 Not used 9 Not used 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 84 BDL3221 LCD/TV Go to cover page 32 13 GENERAL PRODUCT SPECIFICATION(Continued) 3.3 PC and TV requirement 3.3.1 PC interface 3.3.1.1 Mode storing capacity Pre-set : 12 User modes : 12 New modes : 8 3.3.1.2 Horizontal scanning Sync polarity : Positive or Negative Scanning frequency : 30 - 63 KHz 3.3.1.3 Vertical scanning Sync polarity : Positive or Negative Scanning frequency : 56 - 75 Hz 3.3.1.4 Input connectors A. Input analog D-sub connector pin assignment B. Output analog D-sub connector pin assignment - 1.8m 15Pins D-sub male with DDC2B Pin assignments. PIN No. SIGNAL (PC) 1 Red 2 Green 3 Blue 4 GND 5 GND 6 Red GND 7 Green GND 8 Blue GND 9 +5V (Supply from PC) 10 Sync GND 11 GND 12 Bi-directional data 13 H-sync 14 V-sync 15 Data clock PIN No. SIGNAL 1 Red_OUT 2 Green_OUT 3 Blue_OUT 4 GND 5 GND 6 Red GND 7 Green GND 8 Blue GND 9 GND 10 Sync GND 11 GND 12 GND 13 H-sync_OUT 14 V-sync_OUT 15 GND BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 85 Go to cover page 14 32 GENERAL PRODUCT SPECIFICATION(Continued) C. DVI-D : Pin assignment (for PC DVI and Video HDCP) 3.3.1.5 Available timings Factory pre-set timing, size and centering are according to the reference timing charts, The list is as below: Remark:Mode 1,3,4,5,7,9,11 will run auto adjustment only, and W/O QA checking Pin No. Description 1 RX2- 2 RX2+ 3 GND 4 GND 5 GND 6 DDC clock 7 DDC data 8 GND 9 RX1- 10 RX1+ 11 GND 12 GND 13 GND 14 +5V 15 GND 16 +5V 17 RX0- 18 RX0+ 19 GND 20 GND 21 GND 22 GND 23 RXC+ 24 RXC- MODE NO. 1 2 3 4 RESOLUTION 640 x 350 640 x 480 640 x 480 720 x 400 Dot clock(MHz) 25.175 25.175 31.500 28.321 f h 31.469kHz 31.469kHz 37.500kHz 31.469kHz A ( us ) 31.778 (800 dots) 31.778 (800 dots) 26.667 (840 dots) 31.78(900dots) B ( us ) 3.813 ( 96 dots) 3.813 ( 96 dots) 2.032 ( 64 dots) 3.813(108dots) C ( us ) 1.907 ( 48 dots) 1.907 ( 48 dots) 3.810 ( 120 dots) 1.907(54dots) D ( us ) 25.422 (640 dots) 25.422 (640 dots) 20.317 ( 640 dots) 25.42(720dots) E ( us ) 0.636 ( 16 dots) 0.636 ( 16 dots) 0.508 ( 16 dots) 0.636(18dots) f v 70Hz ( 70.086 ) 60Hz ( 59.940 ) 75Hz (75 ) 70Hz(70.087) O (ms ) 14.268 ( 449 lines) 16.683 (525 lines ) 13.333 (500 lines) 14.27(449 lines) P ( ms ) 0.064 (350 lines ) 0.064 ( 2 lines ) 0.080 ( 3 lines) 0.064(2 lines) Q (ms ) 1.715 ( 54 lines ) 1.049 ( 33 lines ) 0.427 ( 16 lines) 1.112(34 lines) R ( ms ) 11.122 ( 350lines ) 15.253 (480 lines ) 12.80 (480 lines) 12.71(400 lines) S ( ms ) 0.192 ( 6 lines ) 0.317 ( 10 lines) 0.027 ( 1 line ) 0.384(13 lines) SYNC. H/V +/- - / - - / - -/+ POLARITY SEP . SYNC Y Y Y Y 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 86 BDL3221 LCD/TV Go to cover page 32 15 GENERAL PRODUCT SPECIFICATION(Continued) MODE NO. 5 6 7 8 RESOLUTION 800 x 600 800 x 600 800 x 600 1024 x 768 Dot clock(MHz) 36.000 40.000 49.500 65.000 f h 35.156kHz 37.879kHz 46.875kHz 48.363kHz A ( us ) 28.44 (1024 dots) 26.40 (1056 dots) 21.333 (1056dots) 20.677(1344 dots) B ( us ) 2.000 ( 72 dots) 3.200 ( 128 dots) 1.616 ( 80 dots) 2.092(136 dots) C ( us ) 3.556 ( 128 dots) 2.200 ( 88 dots) 3.232 ( 160 dots) 2.462(160 dots) D ( us ) 22.22 ( 800 dots) 20.00 ( 800 dots) 16.162 ( 800 dots) 15.754(1024 dots) E ( us ) 0.667 ( 24 dots) 1.000 ( 40 dots) 0.323 ( 16 dots) 0.369(24 dots) f v 56Hz ( 56.250) 60Hz ( 60.316) 75Hz ( 75.000) 60.004Hz O (ms ) 17.78 (625 lines) 16.58 (628 lines) 13.333 (625lines) 16.666(806 lines) P ( ms ) 0.057 ( 2 lines) 0.106 ( 4 lines) 0.064 ( 3 lines) 0.124(6 lines) Q (ms ) 0.626 ( 22 lines) 0.607 ( 23 lines) 0.448 ( 21 lines) 0.600(29 lines) R ( ms ) 17.07 ( 600 lines) 15.84 (600 lines) 12.80 (600lines) 15.880(768 lines) S ( ms ) 0.028 ( 1 lines) 0.026 ( 1 line ) 0.021 ( 1 line ) 0.062(3 lines) SYNC. H/V + / + + / + + / + -/- POLARITY SEP . SYNC Y Y Y Y MODE NO. 9 10 11 12 RESOLUTION 1024 x 768 1280 x 720 1280 x 768 1360 x 768 CVT CVT CVT Dot clock(MHz) 78.750 74.5 79.50 84.75 f h 60.023kHz 44.772kHz 47.776kHz 47.720kHz A ( us ) 16.66 (1312dots) 22.336 (1664 dots) 20.931 (1664 dots) 20.956 (1776dots) B ( us ) 1.219 ( 96 dots) 1.718 ( 128 dots) 1.610 ( 128 dots) 1.605 ( 136 dots) C ( us ) 2.235 ( 176 dots) 2.577 ( 192 dots) 2.415 ( 192 dots) 2.454 ( 208 dots) D ( us ) 13.00 (1024dots) 17.18 (1280 dots) 16.10 (1280 dots) 16.047(1360dots) E ( us ) 0.203 ( 16 dots) 0.859 ( 64 dots) 0.805 ( 64 dots) 0.850( 72 dots) f v 75Hz ( 75.029) 60Hz (59.855) 60Hz (59.87) 60Hz (59.799) O (ms ) 13.328 (800 lines) 16.707 (748 lines) 16.703 (798 lines) 16.723 (798 lines) P ( ms ) 0.050 ( 3 lines) 0.117 ( 5 lines) 0.1455 ( 7 lines) 0.105 ( 5 lines) Q (ms ) 0.466 ( 28 lines) 0.4477 ( 20 lines) 0.4186 ( 20 lines) 0.461( 22 lines) R ( ms ) 12.795 (768 lines) 16.082 (720 lines) 16.075 (768lines) 16.094 (768 lines) S ( ms ) 0.017 ( 1 line) 0.067 ( 3 lines) 0.0628 ( 3 lines) 0.063 ( 3 lines) SYNC. H/V +/+ -/+ -/+ -/+ POLARITY SEP . SYNC Y Y Y Y A : H-Total O : V-Total B : H- Sync width P : V- Sync width C : H- Back porch Q :.V- Back porch D : H- Video width R : V- Video length E : H- Front porch S :.V- Front porch BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 87 Go to cover page 16 32 GENERAL PRODUCT SPECIFICATION(Continued) 3.3.2 I/O interface Connectors: 1. Tuner: RTMA M/N system reception for NAFTA model Multi-standard for WE model Multi-standard PAL/NTSC for AP model PAL D/K for China model 2. DVI IN: DVI input (PC and TV digital signal support HDCP) with share with VGA audio IN . 3. PC IN: VGA input (D-SUB connectors) with audio R/L(mini-jack). 4. HD IN: HDTV input with YPbPr format with R/L audio in. 5. AV OUT: Composite video output (CVBS) and audio R/L(RCA jack). 6. AV IN : Video (CVBS) and S-Video share with same audio R/L. 7. EXT IN: Video (CVBS), S-Video and RGB input, TV AV output. 8. Headphone out 9. VGA out: VGA loop through. 10. RS232 in/out : For control . Location: Rear down side Rear left Side TUNER Box DVI in/ HDCP VGA out EX T VGA audio in VGA in RS23 2 IN IN AV /Audio L/R output HD/Audio L/R in RS23 2 out Speaker connector AC Inlet AC Switch Headphone out S-video in AV in S-Video/AV audio L/R in 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 88 BDL3221 LCD/TV Go to cover page 32 17 GENERAL PRODUCT SPECIFICATION(Continued) 3.3.3 TV Interface 3.3.3.1 TV Tuner RF input : Aerial or Cable Input impedance 75 ? 3.3.3.2 Deviation of TV system Following table is the deviation of main TV system. Model W EUROPE America AP China Tuner FQ1216ME5/I H-5 Picture carrier 38.9MHz FQ1236/F H-5 Picture carrier 45.75MHz FQ1216PN/I H-5 Picture carrier 38.9MHz FQ1256/I H-3 Picture carrier 38MHz TV Color system PAL, SECAM NTSC PAL/NTSC PAL V system B/G, D/K, I, L M B/G, NTSC-M D/K Sound decoder MSP3450G MSP3450G MSP3450G MSP3450G CVBS, YC Color system Multi Multi Multi Multi Scaler MCU WE version NAFTA version AP version China version Closed caption N Y N N V-chip N Y N N Teletext Y N Y N Remote controller (RC5) WE version NAFTA version WE version WE version Channel number 100 US Air 68, cable 125 100 100 Following table is the detail TV System list. TV system Position of sound carrier(MHz) Sound system Color system Country 4.5/4.724212 FM-Stereo (A2) NTSC Korea 4.5 FM-FM (EIA-J) NTSC Japan M 4.5 BTSC-stereo SAP NTSC USA N 4.5 BTSC-stereo SAP PAL Argentina 5.5/5.7421875 FM-stereo (A2) PAL Germany, Austria, Switzerland, Italy, Netherlands. B/G 5.5/5.85 FM-Mono/NICAM PAL Belgium, Spain, Denmark, Finland, Norway, Sweden. L 6.5/5.85 AM-Mono/NICAM SECAM-L France I 6.0/6.552 FM-Mono/NICAM PAL Great Britain, Hong Kong, Ireland. 6.5/6.2578125 FM-Stereo (A2, D/K1) SECAM-East Slovak. Rep. 6.5/6.7421875 FM-Stereo (A2, D/K2) PAL None 6.5/5.7421875 FM-Stereo (A2, D/K3) SECAM-East Poland D/K 6.5/5.85 FM-Mono/ NICAM (D/K, NICAM) PAL China, Hungary 3.3.3.3 TV color setting There are three color for factory to select and the preset color is cool. 3.3.3.4 TV audio setting Sound power outputs: - Stereo: 2 x 10 Watts, THD 10% Sound controls: BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 89 Go to cover page 18 32 GENERAL PRODUCT SPECIFICATION(Continued) - Treble - Bass - Balance - Volume adjust - Surround sound on/off - Mute on/off ( Speaker on/off ) - Smart sound ( Personal , News , Music , Theater ) Sound mute : - When no video recognition on terrestrial tuner signal, the sound must be muted 3.3.3.5 TV special setting Teletext : ( For WE, Tuner ,CVBS input source only) - TXT on/off - Enlarge - Hold - Reveal - Mix - Quick search from color keys Close Caption, V-chip ( For NAFTA---Tuner ,CVBS input source only) - CC-1 .... CC-4 , CC_MUTE decoding and display - TXT1.....TXT4 Text mode - support violence rating and checking(V-chip) 3.3.4 Electric characteristics of I/O 3.3.4.1 PC Signal type Analog Video : 0.7 Vp-p linear, positive polarity Separate Sync. : TTL level, separate, positive or negative polarity Signal source : pattern generator format as attachment. (Table 1 to 6) Reference generator: CHROMA 2200 or 2250 PC Audio input Location: Rear down side Specification Audio L/R input - Nominal : 0.5 V rms. - Maximum : 1.5 V rms. - Impedance > 10 k �. Note : the input will be overloaded when the signal > 1.5 V rms. Connector type : 3.5 mm mini Jack ESD-protected : 15 kV 3.3.4.2 TV Signal type 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 90 BDL3221 LCD/TV Go to cover page 32 19 GENERAL PRODUCT SPECIFICATION(Continued) RF signal Aerial input / 10mV(80dBuV) HD / Component Y Pb Pr Video input , Audio input Location : Rear down side Specification Video - Y : 700mV, Pb, Pr, : +/- 350mV, - Impedance : 75 � Audio: L/R input - Nominal : 0.5 V rms. - Maximum : 1.5 V rms. - Impedance > 10 k �. Note : the input will be overloaded when the signal > 1.5 V rms. Connector type : RCA Jack ESD-protected : 15 kV S-Video Video input, Audio input Location : side Specification Video - Y : 1Vpp , C : 300 mV pp - Impedance : 75? . Audio L/R input (share with Composite Audio input ) - Nominal : 0.5 V rms. - Maximum : 1.5 V rms. -Impedance > 10 k �. Note : the input will be overloaded when the signal > 1.5 V rms. Connector type : RCA Jack ESD-protected : 15 kV AV input Location : Side Specification Video - CVBS Source signal 1 Vpp - Impedance : 75 �. Audio L/R input (share with S-Video Audio input ) - Nominal : 0.5 V rms. - Maximum : 1.5 V rms. -Impedance > 10 k �. Note : the input will be overloaded when the signal > 1.5 V rms. Connector type : RCA Jack ESD-protected : 15 kV SCART input / output: ( for WE model only ) Location : Rear down side Specification : CVBS Video Audio signals input and output FULL SCART according EN50049-1A3 The sound output signal on the connector must be muted in case of no terrestrial video input Connector type : 21 pin black Euro connector ESD protected : 15KV SCART Pin assignment ( for WE model only ) BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 91 Go to cover page 20 32 GENERAL PRODUCT SPECIFICATION(Continued) 3.3.4.3 CVBS output : Location : Rear down side Specification Video - CVBS output. 1 Vpp ( from CVBS source ) - Impedance : 75 �. Audio L/R output ( from CVBS source ) - Nominal : 0.5 V rms. - Maximum : 1.5 V rms. -Impedance > 10K �. Connector type : RCA Jack ESD-protected : 15 kV 3.3.4.4 Headphone output : Audio: R/L output 10mW at 32 �. 3.5mm stereo jack with switch Impedance is between 8 and 600 3.3.5 Picture in Picture 3.3.5.1 Display function � PIP can only be functional for video and TV monitors. � PIP factory default is CVBS video input. � A black PIP display window will be shown if there is no video signal input while PIP on. PIN No. SIGNAL 1 Audio output B ( right ) 2 Audio input B ( right ) 3 Audio output A ( left ) 4 Ground (audio ) 5 Ground ( blue ) 6 Audio input A ( left ) 7 Blue input 8 Function select 9 Ground ( green ) 10 Comms data 2 11 Green input 12 Comms data 1 13 Ground ( red ) 14 Ground ( blanking ) 15 Red input 16 RGB switching control 17 Ground ( video input & output ) 18 Ground ( RGB switching control ) 19 Video output ( composite ) 20 Video input ( composite ) 21 Common ground ( shield ) 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 92 BDL3221 LCD/TV Go to cover page 32 21 GENERAL PRODUCT SPECIFICATION(Continued) 3.3.5.2 Display size � There are 4 different size of PIP, Small , medium , large and PBP � Press PIP key to start up the picture-in-picture display in small size. They will be operated in a carousel sequence: � PIP OFF > PIP small > PIP medium > PIP large > PBP > PIP OFF > .... 3.3.5.3 Display location � The location of PIP should be adjustable and be at the four corners of the monitor. � Press Menu key and select the PIP item in Feature menu, then access DISPLAY for PIP location adjustment. 3.3.5.4 Picture by Picture � The display is equally divided into two parts, one displays PC graphics, and another displays video input. This selection item can be under PIP selection to reduce complexity of the menu. 3.3.5.5 Zoom � Four zoom modes will be provided: 4x4, 3x3, 2x2, and 1x5. � Zoom ID: Users can use either RS232C or OSD (via remote control) to select which portion of the entire image to be shown. The ID will be designated as A1, A2, ..., B1, B2, in a row by row way. 3.4 Power input connection Power cord length : 1.8 M Power cord type : 3 leads power cord with protective earth plug. 3.5 Power management PC mode The power consumption and the status indication of the set with power management function are as follows: Power Spec STATUS Horizontal Vertical 120VAC 230VAC LED On Pulse Pulse (Typical 100W) BLUE Stand-by No Pulse Pulse < 5 W < 5W Amber Suspend Pulse No Pulse < 5 W < 5W Amber Off No Pulse No Pulse < 5 W < 5 W Amber DC Power switch off - - < 3 W < 3 W - TV mode The power consumption and the status indication of the set with power management function are as follows, Power Spec STATUS 120VAC 230VAC LED On (Typical 130W) BLUE Stand-by < 5 W < 5 W Amber DC Power switch off < 3W < 3W - In Monitor power saving mode, Which no H&V sync or absent either H-sync or V-sync input via VGA connector. The monitor will enter "Monitor saving mode". The way to wake up or change source: 1. H-sync and V-sync have signal again. 2. Press "Source" key on remote control, change to video source directly. In TV power saving mode, Which switched off by RC "Power" key, SLEEP TIMER function or no TV signal input for 30 minutes, the monitor will enter "TV standby mode" and LED shows amber color. The way to wake up: 1. Press "Power" key on remote control to return original video source. 2.Press "Source" key on remote control, change to video source directly. BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 93 Go to cover page 22 32 GENERAL PRODUCT SPECIFICATION(Continued) 4.0 Visual characteristics 4.1 Test conditions Unless otherwise specified, this specification is defined under the following conditions. (1) Input signal : As defined in 3.3.1.5, 1360 x 768 x 60Hz non-interlaced mode (47.720kHz), signal sources must have 75 ohm output impedance. (2) Luminance setting: controls to be set to 500 cd/m2 (typical) with full screen 700mv white signal. (3) Warm up: more than 30 minutes after power on with signal supplied. (4) Ambient light: 400 ~ 600 lux. (5) Ambient temperature: 25 � 2 �C 4.2 PC Resolution Dot rate (MHz) H.freq (KHz) Mode Resolution V.freq (Hz) Remark 1 25.175 31.469 VGA-1 640*350 70.086 2 25.175 31.469 IBM VGA 640 * 480 59.940 3 31.500 37.500 VGA 640 * 480 75.000 4 28.322 31.469 VGA 720*400 70.087 5 36.000 35.156 VESA 800 * 600 56.250 6 40.000 37.879 VESA 800 * 600 60.317 7 49.500 46.875 VESA 800 * 600 75.000 8 65.000 48.363 VESA 1024 * 768 60.004 9 78.750 60.023 VESA 1024 * 768 75.029 10 74.500 47.772 WXGA 1280 * 720 59.855 CVT 11 79.500 47.776 WXGA 1280 * 768 59.870 CVT 12 84.75 47.720 WXGA 1360 * 768 59.799 CVT 4.3 Brightness >400 cd/m2 at maximum contrast and Brightness. (At center of the screen, Fig. 1) 4.4 Image size 4.4.1 Actual display size 697.685 x 392.256mm 4.5 Brightness uniformity Set contrast at 100% and turn the brightness to Max. (At original color) Apply the Fig 1, it should comply with the following formula: Maximum luminance of five points (brightness) �������������������� <1.3 Minimum luminance of five points (brightness) 4.6 PC White color adjustment Apply 1360x768@60Hz mode set smart picture to “Normal”,Apply full white pattern, with brightness in 50 % position and the contrast control at 50% position. The 1931 CIE Chromaticity (color triangle) diagram (X, Y) coordinate for the screen center should be: 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 94 BDL3221 LCD/TV Go to cover page 32 23 GENERAL PRODUCT SPECIFICATION(Continued) For NORMAL COLOR Equivalent 6500�K X = 0.313 +/- 0.030 Y = 0.329 +/- 0.030 For COOL PRESET Equivalent 9300 �K X = 0.283 +/- 0.030 Y = 0.297 +/- 0.030 For WARM PRESET Equivalent 5700 �K X = 0.328 +/- 0.030 Y = 0.344 +/- 0.030 4.7 TV White color adjustment Smart picture set to personal for TV RF signal (80dB�v). Use FLUKE 54200 pattern generator with full white pattern. Use The 1931 CIE Chromaticity (color triangle) diagram (X, Y) coordinate for the screen center should be: 9300 �K X=0.289+/-0.030, Y=0.304+/-0.030. 4.8 TV picture centering Use CVBS (PAL and NTSC) input with cross hatch pattern to check the picture centering and should be Left (size)-Right (size) < � 3mm. Up (size)-Down (size) < � 3mm. 4.9 HD support timing 1920X1080I 60Hz 1920X1080I 50Hz 1280X720P 60Hz 1280X720P 50Hz 720X576P 50Hz 720X480P 60Hz 720X576i 50Hz 720X480i 60Hz (For Quantum Data setting with Q801GD or Q802G with YPbPr mode.) BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 95 Go to cover page 24 32 GENERAL PRODUCT SPECIFICATION(Continued) 4.9.1 HD detail timing Item 1920X1080i 60Hz 1280X720P 60Hz 1920X1080i 50Hz 1280X720P 50Hz Pixel rate 74.25MHz (13.468 ns) 74.25MHz (13.468 ns) 74.25MHz ( 13.468ns ) 74.25MHz (13.468 ns) Horizontal Frequency 33.75KHz 45KHz 28.125KHz 37.5KHz Active 1920 pixels (25.859 us) 1280 pixels (17.239 us) 1920 pixels (25.859 us) 1280 pixels (17.239 us) Blank 280 pixels(3.771 us) 370 pixels(4.983 us) 720 pixels( 9.697 us ) 700 pixels(9.428 us) Period 2200 pixels (29.630 us) 1650 pixels(22.222 us) 2640 pixels (35.556 us ) 1980 pixels(26.667 us) Pulse delay 44 pixels(0.593 us) 70 pixels(0.943 us) 484 pixels( 6.519 us ) 400 pixels(5.387 us) Pulse width 44 pixels(0.593 us) 40 pixels(0.539 us) 44 pixels( 0.593 us ) 40 pixels(0.539 us) Vertical Frequency 60 Hz 60 Hz 50 Hz 50 Hz Active 1080 lines(32.000 ms) 720 lines(16.0 ms) 1080 lines( 38.4 ms ) 720 lines(19.2 ms) Blank 45 lines (1.333 ms) 30 lines (0.667 ms) 45 lines (1.6 ms ) 30 lines (0.8 ms) Period 1125 lines(33.333 ms) 750 lines(16.667 ms) 1125 lines( 40 ms ) 750 lines(20 ms) Pulse delay 2 lines(0.059 ms) 5 lines(0.111 ms ) 2 lines( 0.071 ms ) 5 lines(0.133 ms ) Pulse width 5 lines(0.148 ms) 5 lines(0.111 ms) 5 lines(0.178 ms ) 5 lines(0.133 ms) EQ before 0 line 0 line 0 line 0 line EQ after 1 line 0 line 1 line 0 line Scan Interlace Progressive Interlace Progressive Sync type ACS ACS ACS ACS Video kind Analog YPbPr (ITU-R BT.709) Analog YPbPr (ITU-R BT.709) Analog YPbPr (SMPTE BT.709 ) Analog YPbPr (ITU-R BT.709) Item 720X576P 50Hz 720X480P 60Hz 720X576i 50Hz 720X480i 60Hz Pixel rate 27 MHz (37.037 ns) 27.027MHz (37.000 ns) 13.5MHz ( 74.074 ns ) 13.5MHz ( 74.074 ns ) Horizontal Frequency 31.25 KHz 31.5KHz 15.625KHz 15.734KHz Active 720 pixels(26.667 us) 720 pixels(26.640 us) 720 pixels (53.333 us) 720 pixels(53.333 us) Blank 144 pixels(5.333 us) 138 pixels(5.106 us) 144 pixels ( 10.667 us ) 138 pixels( 10.222 us ) Period 864 pixels (32.000 us) 858 pixels (31.746 us) 864 pixels ( 64.00 us ) 858 pixels ( 63.556 us ) Pulse delay 12 pixels(0.444 us) 16 pixels(0.592 us) 12 pixels ( 0.889 us ) 19 pixels( 1.407 us ) Pulse width 63 pixels (2.333 us) 62 pixels (2.294 us) 63 pixels ( 4.667 us ) 62 pixels ( 4.593 us ) Vertical Frequency 50 Hz 60 Hz 50 Hz 59.94 Hz Active 576 lines(18.432 ms) 480 lines(15.238 ms) 576 lines( 36.864 ms ) 480 lines( 30.507 ms ) Blank 49 lines (1.568 ms ) 45 lines(1.429 ms) 49 lines(3.136 ms ) 45 lines(2.860 ms ) Period 625 lines(20.000 ms) 525 lines (16.667 ms) 625 lines ( 40 ms ) 525 lines( 33.367 ms ) Pulse delay 5 lines(0.160 ms) 9 lines (0.287 ms) 2 lines ( 0.128 ms ) 4 lines ( 0.254 ms ) Pulse width 5 lines(0.160 ms) 6 lines (0.190 ms) 3 lines(0.192 ms ) 3 lines(0.191 ms ) EQ before 0 line 0 line 2 line 3 line EQ after 0 line 0 line 2 line 3 line Scan Progressive Progressive Interlace Interlace Sync type ACS ACS ACS ACS Video kind Analog YPbPr (SMPTE RP177) Analog YPbPr SMPTE RP177 Analog YPbPr (SMPTE RP177 ) Analog YPbPr (SMPTE RP177 ) 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 96 BDL3221 LCD/TV Go to cover page 32 25 GENERAL PRODUCT SPECIFICATION(Continued) 5.0 Mechanical characteristics 5.1 Controls Side Control : - Input key - Down key - Up key - Left key - Right key - Menu key - DC power switch Front - Light sensor - RC sensor - Power indicator Rear I/O : - AC inlet - Speaker out (R+/R- L+/L-) - DVI-D in - VGA out - RS232 in - RS232 out - VGA in - Mini jack PC audio input - Compoent(YpbPr) video in (support from 480i to 1080i) - L/R audio input for Compoent video - EXT IN (SCART) - CVBS out - L/R audio output - S-Video input - CVBS in - L/R audio input for CVBS and S-video - Headphone - Tuner RF input 5.2 Unit dimension / Weight Set dimension : 794 mm W x 517 mm H x 244 mm D (incl. Pedestal, excl. speaker) Speaker dimension (single) : 110 mm W x 490 mm H x 70 mm D Net weight (set) : 19.17 Kg exclude speaker boxes Net weight (speaker boxs) : 2.8 Kg 5.3 Tilt base Tilt angle : No Swivel rotation : No 5.4 Transportation packages 5.4.1 Shipping dimension/Weight Carton dimension (packing dimension): 1174mm W x 640 mm H x 373 mm D Gross weight : 28.5 Kg (include speaker boxes 2.8 kg, excluding accessory) 5.4.2 Block unit / Palletization (Sea shipment) Container layers/block sets/layer sets/block unit blocks/container total sets 40` 3 3 9 20 180 6.0 Environmental characteristics BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 97 Go to cover page 26 32 GENERAL PRODUCT SPECIFICATION(Continued) The following sections define the interference and susceptibility condition limits that might occur between external environment and the display device. 6.1 Susceptibility of display to external environment Operating - Temperature : 0 to 40 - Humidity : 10 to 90% - Altitude : 0 to 12000 feet - Air pressure : 645 mBAR - (guaranteed optical performance): 5 to 35 - (guaranteed functional performance): 5 to 40 Storage - Temperature : 0 to 60 - Humidity : 5 to 90% (non - condensing ) - Air pressure : 600 to 1100 mBAR Note: recommend at 0 to 35�C, Humidity less than 60 % Shipping - Temperature :( -20 to 60 degrees ) - Humidity : 5 to 95% (non - condensing ) - Altitude : 0 to 40000 feet ( non operating ) - Air pressure : 188 to 1100 mBAR 6.2 Transportation tests Standard NSTA exclude China & India NSTA for China & India Height 30.5 cm 45.7 cm 1 Corner - 3 Edges - 6 Faces Total 10 Drops Drop Sequence Test Electrical function ok Test Mechanical function ok Result No serious damage on set appearance (room temp./-10 , humidity 70 %) Sequence --- PACKAGING Vibration 0.73Grms Truck spectruh 5~500Hz, 30min for each axis, 3AXES Test Test Electrical function ok Result Mechanical function ok No serious damage on set appearance 6.3 Display disturbances from external environment According to IEC 801-2 for ESD disturbances 7.0 Reliability 7.1 Mean Time Between Failures System MTBF (Excluding the LCD panel and EEFL) : 50,000 hrs EEFL MTBF : 50,000 hrs 8.0 Quality assurance requirements 8.1 Acceptance test According to MIL-STD-105D Control II level AQL : 0.65 (major) 2.5 (minor) (Please also refer to annual quality agreement) 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 98 BDL3221 LCD/TV Go to cover page 32 27 GENERAL PRODUCT SPECIFICATION(Continued) 9.0 Serviceability The serviceability of this monitor should fulfill the requirements which are prescribed in UAW-0346 and must be checked with the check list UAT-0361. 10.0 Appendices Fig 1: Pattern 1: Brightness and Uniformity measure points Pattern 2: Cross talk pattern Gray level 184 (256 Gray level) YA 1/2 1/2 1/6 Pattern 3: Cross talk Pattern Center at Gray level 0 (Black) YB 1/2 1/2 1/6 1/3 1/3 1/3 1/3 1/3 b b 1 2 3 5 4 H/2 3H/ 4 V/4 V/2 3V/ 4 H/4 H V a b a b a b a b BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 99 Go to cover page 28 32 GENERAL PRODUCT SPECIFICATION(Continued) Table 1. WE model : West Europe TV preload Channels Frequency Carriers PRG CH Video Sound TV System Pattern 0 1 AU37 590.25MHz 595.75MHz PAL B(UK) Pure White 2 AU2 64.25MHz 69.75MHz PAL B(UK) Circle Pattern 3 E7 189.25MHz 194.75MHz PAL B (CCIR) Circle Pattern 4 G47 679.25MHz 684.75MHz PAL G (CCIR) Circle Pattern 5 I23 487.25MHz 493.75MHz PAL I (UK) Circle Pattern 6 E12 224.25MHz 229.75MHz PAL B (CCIR) Color Bar 7 AU7 182.25MHz 187.75MHz PAL B (UK) Color Bar 8 G68 847.25MHz 852.75MHz PAL G (CCIR) 100% White 9 AU9 196.25MHz 201.75MHz PAL B (UK) Checkerboard 10 AU10 209.25 MHz 214.75 MHz PAL B (UK) Crosshatch 11 AU0 46.25MHz 51.75MHz PAL B (UK) Color Bar 12 AU2 64.25MHz 69.75MHz PAL B (UK) Color Bar PRG CH Frequency Carriers TV System Pattern PRG 13 AU5 102.25 MHz 107.75 MHz PAL B (UK) Crosshatch 14 AU5A 138.25MHz 143.75MHz PAL B (UK) Color Bar 15 AU7 182.25MHz 187.75MHz PAL B (UK) Pure White 16 AU9 196.25MHz 201.75MHz PAL B (UK) Pure White 17 AU10 209.25MHz 214.75MHz PAL B (UK) Circle Pattern 18 I23 487.25MHz 493.75MHz PAL I (UK) Circle Pattern 19 G28 527.25MHz 532.75MHz PAL G (CCIR) Circle Pattern 20 AU37 590.25MHz 595.75MHz PAL G (UK) Circle Pattern 21 I40 623.25MHz 629.75MHz PAL I (UK) Color Bar 22 CH44 655.25MHz 661.75MHz PAL DK (UK) Color Bar 23 I60 783.25MHz 789.75MHz PAL I (UK) 100% White 24 I66 831.25MHz 837.75MHz PAL I (UK) Checkerboard 25 K21 471.25 MHz 477.75 MHz SEC K1 (CCIR) Crosshatch 28 G28 527.25MHz 532.75MHz PAL G (UK) Color Bar 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 100 BDL3221 LCD/TV Go to cover page 32 29 GENERAL PRODUCT SPECIFICATION(Continued) Table 2. NAFTA model : US- Air broadcast channel Broadcast Channel Video Carrier (MHz) Audio Carrier (MHz) Range (MHz) 2 55.25 59.75 54-60 3 61.25 65.75 60-66 4 67.25 71.75 66-72 5 77.25 81.75 76-82 6 83.25 87.75 82-88 7 175.25 179.75 174-180 8 181.25 185.75 180-186 9 187.25 191.75 186-192 10 193.25 197.75 192-198 11 199.25 203.75 198-204 12 205.25 209.75 204-210 13 211.25 215.75 210-216 14 471.25 475.75 470-476 15 477.25 481.75 476-482 16 483.25 487.75 482-488 17 489.25 493.75 488-494 18 495.25 499.75 494-500 19 501.25 505.75 500-506 20 507.25 511.75 506-512 21 513.25 517.75 512-518 22 519.25 523.75 518-524 23 525.25 529.75 524-530 24 531.25 535.75 530-536 25 537.25 541.75 536-542 26 543.25 547.75 542-548 27 549.25 553.75 548-554 28 555.25 559.75 554-560 29 561.25 565.75 560-566 30 567.25 571.75 566-572 31 573.25 577.75 572-578 42 579.25 583.75 578-584 33 585.25 589.75 584-590 34 591.25 595.75 590-596 35 597.25 601.75 596-602 36 603.25 607.75 602-608 37 609.25 613.75 608-614 38 615.25 619.75 614-620 39 621.25 625.75 620-626 40 627.25 631.75 626-642 41 633.25 637.75 642-638 42 639.25 643.75 638-644 43 645.25 649.75 644-650 44 651.25 655.75 650-656 45 657.25 661.75 656-662 46 663.25 667.75 662-668 47 669.25 673.75 668-674 48 675.25 679.75 674-680 49 681.25 685.75 680-686 50 687.25 691.75 686-692 51 673.25 697.75 692-698 52 699.25 703.75 698-704 53 705.25 709.75 704-710 54 711.25 715.75 710-716 55 717.25 721.75 716-722 56 723.25 727.75 722-728 57 729.25 733.75 728-734 58 735.25 739.75 734-740 59 741.25 745.75 740-746 60 747.25 751.75 746-752 61 753.25 757.75 752-758 62 759.25 763.75 758-764 63 765.25 769.75 764-770 64 771.25 775.75 770-776 65 777.25 781.75 776-782 66 783.25 787.75 782-788 67 789.25 793.75 788-794 68 795.25 799.75 794-800 69 801.25 805.75 800-806 BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 101 Go to cover page 30 32 GENERAL PRODUCT SPECIFICATION(Continued) US-Cable channel Cable Channel Video carrier MHz Audio carrier MHz Range MHz 2 55.25 59.75 54-60 3 61.25 65.75 60-66 4 67.25 71.75 66-72 1 73.25 77.75 72-78 5 79.25 83.75 76-82 6 85.25 89.75 82-88 95 91.25 95.75 90-96 96 97.25 101.75 96-102 97 103.25 107.75 102-108 98 109.25 113.75 108-114 99 115.25 119.75 114-120 14 121.25 125.75 120-126 15 127.25 131.75 126-142 16 133.25 137.75 142-138 17 139.25 143.75 138-144 18 145.25 149.75 144-150 19 151.25 155.75 150-156 20 157.25 161.75 156-162 21 163.25 167.75 162-168 22 169.25 173.75 168-174 7 175.25 179.75 174-180 8 181.25 185.75 180-186 9 187.25 191.75 186-192 10 193.25 197.75 192-198 11 199.25 203.75 198-204 12 205.25 209.75 204-210 13 211.25 215.75 210-216 23 217.25 221.75 216-222 24 223.25 227.75 222-228 25 229.25 233.75 228-234 26 235.25 239.75 234-240 27 241.25 245.75 240-246 28 247.25 251.75 246-252 29 253.25 257.75 252-258 30 259.25 263.75 258-264 31 265.25 269.75 264-270 42 271.25 275.75 270-276 33 277.25 281.75 276-282 34 283.25 287.75 282-288 35 289.25 293.75 288-294 36 295.25 299.75 294-300 37 301.25 305.75 300-306 38 307.25 311.75 306-312 39 313.25 317.75 312-318 40 319.25 423.75 318-424 41 425.25 429.75 424-330 42 331.25 335.75 330-336 43 337.25 341.75 336-342 44 343.25 347.75 342-348 45 349.25 353.75 348-354 46 355.25 359.75 354-360 47 361.25 365.75 360-366 48 367.25 371.75 366-372 49 373.25 377.75 372-378 50 379.25 383.75 378-384 51 385.25 389.75 384-390 52 391.25 395.75 390-396 53 397.25 401.75 396-402 54 403.25 407.75 402-408 55 409.25 413.75 408-414 56 415.25 419.75 414-420 57 421.25 425.75 420-426 58 427.25 431.75 426-442 59 433.25 437.75 442-438 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 102 BDL3221 LCD/TV Go to cover page 32 31 GENERAL PRODUCT SPECIFICATION(Continued) 60 439.25 443.75 438-444 61 445.25 449.75 444-450 62 451.25 455.75 450-456 63 457.25 461.75 456-462 64 463.25 467.75 462-468 65 469.25 473.75 468-474 66 475.25 479.25 474-480 67 481.25 485.75 480-486 68 487.25 491.75 486-492 69 493.25 497.75 492-498 70 499.25 503.75 498-504 71 505.25 509.75 504-510 72 511.25 515.75 510-516 73 517.25 521.75 516-522 74 523.25 527.75 522-528 75 529.25 533.75 528-534 76 535.25 539.75 534-540 77 541.25 545.75 540-546 78 547.25 551.75 546-552 79 553.25 557.75 552-558 80 559.25 563.75 558-564 81 565.25 569.75 564-570 82 571.25 575.75 570-576 83 577.25 581.75 576-582 84 583.25 587.75 582-588 85 589.25 593.75 588-594 86 595.25 599.75 594-600 87 601.25 605.75 600-606 88 607.25 611.75 606-612 89 613.25 617.75 612-618 90 619.25 623.75 618-624 91 625.25 629.75 624-630 92 631.25 635.75 630-636 93 637.25 641.75 636-642 94 643.25 647.75 642-648 100 649.25 653.75 648-654 101 655.25 659.75 654-660 102 661.25 665.75 660-666 103 667.25 671.75 666-672 104 673.25 677.75 672-678 105 679.25 683.75 678-684 106 685.25 689.75 684-690 107 691.25 695.75 690-696 108 697.25 701.75 696-702 109 703.25 707.75 702-708 110 709.25 713.75 708-714 111 715.25 719.75 714-720 112 721.25 725.75 720-726 113 727.25 731.75 726-742 114 733.25 737.75 742-738 115 739.25 743.75 738-744 116 745.25 749.75 744-750 117 751.25 755.75 750-756 118 757.25 761.75 756-762 119 763.25 767.75 762-768 120 769.25 773.75 768-774 121 775.25 779.75 774-780 122 781.25 785.75 780-786 123 787.25 791.75 786-792 124 793.25 797.75 792-798 125 799.25 803.75 798-804 BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 BDL3221 LCD/TV 103 Go to cover page 32 32 GENERAL PRODUCT SPECIFICATION(Continued) Table 3. AP model : AP-Multi TV preload Channels Signal Distribution Table (PAL and NTSC) Frequency Carriers PRG CH Video Sound TV System Pattern 0 1 AU37 590.25MHz 595.75MHz PAL B(UK) Pure White 2 AU2 64.25MHz 69.75MHz PAL B(UK) Circle Pattern 3 E7 189.25MHz 194.75MHz PAL B(CCIR) Circle Pattern 4 G47 679.25MHz 684.75MHz PAL G(CCIR) Circle Pattern 5 I23 487.25MHz 493.75MHz PAL I (UK) Circle Pattern 6 M58 735.25MHz 739.75MHz NTSC M(CCIR) Color Bar 7 AU7 182.25MHz 187.75MHz PAL B(UK) Color Bar 8 K21 471.25MHz 477.75MHz PAL G (CCIR) 100% White 9 AU9 196.25MHz 201.75MHz PAL B(UK) Checkerboard 10 AU10 209.25 MHz 214.75 MHz PAL B(UK) Crosshatch 11 E12 224.25MHz 229.75MHz PAL B(CCIR) Color Bar 12 G34 575.25MHz 580.75MHz PAL G(CCIR) Color Bar 13 G62 799.25 MHz 804.75 MHz PAL G(CCIR) Crosshatch 14 C4 77.25MHz 83.75MHz PAL D(CCIR) Color Bar 28 G28 527.25MHz 532.75MHz PAL G(UK) Color Bar Table 4. China model : China TV preload Channels Signal Distribution Table (PAL D) Frequency Carriers PRG CH Video Sound TV System Pattern 1 C 4 65.25MHz 71.75MHz PAL D(CCIR) Full Write 2 E 7 184.25MHz 190.75MHz PAL D(CCIR) Circle Pattern 3 E12 224.25MHz 230.75MHz PAL D(CCIR) Color Bar 4 K21 471.25MHz 477.75MHz PAL D(CCIR) Full Write 5 G34 511.25MHz 517.75MHz PAL D(CCIR) Circle Pattern 6 G62 547.25MHz 553.75MHz PAL D(CCIR) Color Bar 7 M58 551.25MHz 557.75MHz PAL D(CCIR) Crosshatch 8 G47 615.25MHz 621.75MHz PAL D(CCIR) Color Bar 8639 000 16304 2005-06-17 2005-06-17 590 Freud Yu BRAND : PHILIPS 32 inch BDS WXGA TFT LCD Monitor/TV TYPE : BDL3221V/00 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 104 Go to cover page BDL3221 LCD/TV 0. Warning All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the unit via a wrist wrap with resistance. Keep components and tools also at the same potential ! 1. Servicing of SMDs (Surface Mounted Devices) 1.1 General cautions on handling and storage - Oxidation on the terminals of SMDs results in poor soldering. Do not handle SMDs with bare hands. - Avoid using storage places that are sensitive to oxidation such as places with sulphur or chlorine gas, direct sunlight, high temperatures or a high degree of humidity. The capacitance or resistance value of the SMDs may be affected by this. - Rough handling of circuit boards containing SMDs may cause damage to the components as well as the circuit boards. Circuit boards containing SMDs should never be bent or flexed. Different circuit board materials expand and contract at different rates when heated or cooled and the components and/or solder connections may be damaged due to the stress. Never rub or scrape chip components as this may cause the value of the component to change. Similarly, do not slide the circuit board across any surface. 1.2 Removal of SMDs - Heat the solder (for 2-3 seconds) at each terminal of the chip. By means of litz wire and a slight horizontal force, small components can be removed with the soldering iron. They can also be removed with a solder sucker (see Fig. 1A) While holding the SMD with a pair of tweezers, take it off gently using the soldering iron's heat applied to each terminal (see Fig. 1 B). - Remove the excess solder on the solder lands by means of litz wire or a solder sucker (see Fig. 1C). 1.3 Caution on removal - When handling the soldering.iron. use suitable pressure and be careful. - When removing the chip, do not use undue force with the pair of tweezers. - The soldering iron to be used (approx. 30 W) should preferably be equipped with a thermal control (soldering temperature: 225 to 250 C). - The chip, once removed, must never be reused. 1.4 Attachment of SMDs - Locate the SMD on the solder lands by means of tweezers and solder the component on one side. Ensure that the component is positioned correctly on the solder lands (see Fig.2A). - Next complete the soldering of the terminals of the component (see Fiq. 2B). 2. Caution when attaching SMDs - When soldering the SMD terminals, do not touch them directly with the soldering iron. The soldering should be done as quickly as possible, care must be taken to avoid damage to the terminals of the SMDs themselves. - Keep the SMD's body in contact with the printed board when soldering. - The soldering iron to be used (approx. 30 W ) should preferably be equipped with a thermal control (soldering temperature: 225 to 250 C). - Soldering should not be done outside the solder land. - Soldering flux (of rosin) may be used, but should not be acidic. - After soldering, let the SMD cool down gradually at room temperature. - The quantity of solder must be proportional to the size of the solder land. If the quantity is too great, the SMD might crack or the solder lands might be torn loose from the printed board (see Fig. 3). Fig.3 Examples Right Repair Tips 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 105 Go to cover page BDL3221 LCD/TV 3. Lead-free product identification You can identify lead-free product by Philips-lead-free logo on PCB. 4. Lead-free product repair instruction 4.1 Use only lead-free Solder Alloy 0622 149 00106(1.2mm SAC305) or 0622 14900108(1.0mm SAC305). Remark: For lead free soldering material, please visit website for details. This is recommended by Philips. 4.2 Use only adequate solder tools applicable for lead-free soldering-tin. The solder tool must be able to reach at least a solder-temperature of 400 , to stabilize the adjusted temperature at the solder-tip and to exchange solder-tips for different applications. Small Passives/Actives to be removed with thermal tweezers Automated system for IC and BGA repair (Microscope, Camera, Beam split optics, Computer, Programmer, Heat controllers, Vacuum system, Laser pointer) Solder Hand-Tool (Adjustable in temperature height, Temperature shall be held constant,Flexible tips) 4.3 Adjust your solder tool so that a temperature around 360 -380 is reached and stabilized at the solder joint. Heating-time of the solder-joint should not exceed ~ 4 sec. Avoid temperatures above 400 otherwise wear-out of tips will rise drastically and flux-fluid will be destroyed.Corrosion of Tool-Spikes can be avoided when using SAC305 and a temperature of less than 400 . 4.4 Mix of lead-free solder-tin/parts with leaded soldering-tin/parts is possible but not recommended. If not to avoid clean carefully the solder-joint from old tin and re-solder with new tin. 4.5 Use only original spare-parts listed in the Service-Manuals. Standard-material(consumables) can also be purchased at external companies. 4.6 Special information for lead-free BGA-ICs: this ICs will be delivered in so-called dry-packaging to protect the IC against moisture and with lead-free logo on it. This packaging may only be opened shortly before it is used (soldered). Otherwise the body of the IC gets wet inside and during the heating time the structure of the IC will be destroyed due to high (steam-)pressure. If the packaging was opened before usage the IC has to be heated up for some hours (around 90 ) for drying (Take attention for ESD-protection!) 5. Rework on BGA (Ball Grid Array) ICs General Although (LF)BGA assembly yields are very high, there may still be a requirement for component rework. By rework, we mean the process of removing the component from the PWB and replacing it with a new component. If an (LF)BGA is removed from a PWB, the solder balls of the component are deformed drastically so the removed (LF)BGA has to be discarded. Device Removal As is the case with any component that, it is essential when removing an (LF)BGA, the board, tracks, solder lands, or surrounding components are not damaged. To remove an (LF)BGA, the board must be uniformly heated to a temperature close to the reflow soldering temperature. A uniform temperature reduces the chance of warping the PWB. To do this, we recommend that the board is heated until it is certain that all the joints are molten. Then carefully pull the component off the board with a vacuum nozzle. For the appropriate temperature profiles, see the IC data sheet. Area Preparation When the component has been removed, the vacant IC area must be cleaned before replacing the (LF)BGA. Removing an IC often leaves varying amounts of solder on the mounting lands. This excessive solder can be removed with either a solder sucker or solder wick. The remaining flux can be removed with a brush and cleaning agent. After the board is properly cleaned and inspected, apply flux on the solder lands and on the connection balls of the(LF)BGA Note: Do not apply solder paste, as this has shown to result in problems during re-soldering. Device Replacement The last step in the repair process is to solder the new component on the board. Ideally, the (LF)BGA should be aligned under a microscope or magnifying glass. If this is not possible, try to align the (LF)BGA with any board markers. To reflow the solder, apply a temperature profile according to the IC data sheet. So as not to damage neighbouring components, it may be necessary to reduce some temperatures and times. www.alphametals.com More Information For more information on how to handle BGA devices, visit this URL: http://www.atyourservice.ce.philips.com (needs subscription). After login, select Magazine , then go to Workshop Information . Here you will find Information on how .to deal with BGA-ICs. Repair Tips 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 106 Go to cover page BDL3221 LCD/TV Repair Flow Chart 1.No work/LED is off Check if power switch is normal No Replace Power switch Yes Check power board 1089 pin1,2=16V,pin3=24V, pin4=1.8V,pin5= 4.6V 2.No raster/picture too dim Check power board 1088, pin1~5=24V,pin6= 1.8V pin7=4.6V No Check power board Check power board Yes Check scaler board1503 pin2=1.18V,pin4~5=3.3V No Yes Check power board 1089 pin1,2=16V,pin3=24V, pin4=1.8V,pin5= 4.6V Check power board Yes Check scaler board No 3.No picture/LED is blue Check power board 1088, pin1~5=24V,pin6= 1.8V pin7=4.6V No Check power board Yes Check if working voltage 7852 pin3=3.3V,3855= 3.3V,3864=3.3V No Check circuit around each regulator and eliminate short and open situation Yes Check if clock source 1856,1857, 1101 Replace 1856,1857,1101 No Yes Check if scaler 7403 RGB, clk,H/V and DE signal output 128 bits TTL No Try to replace CPU or CPU's flash Rom CPU's EEPROM Painter Painter's EEPROM Check resistors-network No Replace bad resistors- network Yes Yes Replace LVDS cable Yes Replace LCD panel 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 107 Go to cover page BDL3221 LCD/TV Repair Flow Chart 4.No D-Sub picture Check if H/V signals input to schmitt trigger 7201 No Check input path Yes Check if schmitt trigger 7201 output H/V signals to JAGASM No Replace 7201 Go to 3.No picture/LED is green Yes 5.No TV sound Check if tuner 1676 pin11 output 2nd IF signal No Replace 1676 Yes Check 7676 6.No earthphone sound Check 7902=25V No Eliminate short and open situation Yes Check 7814 pin2=MSP-OUT-R pin6=MSP-OUT-L No Replace 7814 Replace Side AV Board Yes 7.No remote function Tty another remote control No Replace one good remote control Yes Check IR receiver 8.LED and function key poor Check circuit around control board and cable between control board and scaler board 9.No HDCP picture Check 7301 has HDCP code No Write HDCP code in 7301 Yes Check Scaler Board 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 108 Go to cover page BDL3221 LCD/TV Different Parts List Diversity of BDL3221V/27 compared with BDL3221V/00 Item 12NC Description 863900016305 BDL3221V/27 0126 313815567811 RATING LABEL 0291 313815567711 LABEL(LG-NAFTA) 0292 313815567711 LABEL(LG-NAFTA) 0615 313811708631 HEX CODE OF F/W(NO MATL REQ) 1057 313815864781 SACLER PCB ASSY (32-NAFTA) 1172 313818870491 MAINSCORD UL 10A 1M8 DET BK 1176 313923811291 PROD ASSY RC1123512/01 PKD 1255 313815864791 CPU ASSY (LG-NAFTA) 1256 313815864801 EEPROM ASSY(LG-NAFTA) 2021 203803511407 ELCAP REA 35V S 100U PM20 B 3069 212255000177 VDR DC 1MA/459V S MAX 845V R Diversity of BDL3221VS/00 compared with BDL3221V/00 Item 12NC Description 863900016303 BDL3221VS/00 0030 313815760031 FRONT BEZEL ASSY(S) 0032 313815416681 FRONT CORNER-B/R(10709) 0033 313815416671 FRONT CORNER-T/R(10709) 0126 313815567781 RATING LABEL 0194 313815161791 HEAT SINK-PW TRANS 0197 313815321341 INSULATING PLATE 1185 823827718111 LSP BOX 8R 10W-L/R(P302HS) Diversity of 320WN6QS/93 compared with BDL3221V/00 Item 12NC Description 863900016309 320WN6QS/93 0030 313815760031 FRONT BEZEL ASSY(S) 0032 313815416681 FRONT CORNER-B/R(10709) 0033 313815416671 FRONT CORNER-T/R(10709) 0126 313815567821 RATING LABEL 0185 313815161801 HEAT SINK - BRIGE DIODE 0231 313815137371 TV CASE 0232 313815137391 TV COVER 0236 313815567761 RATING LABEL 0291 313815567681 LABEL(LG-CHINA) 0292 313815567681 LABEL(LG-CHINA) 0456 313815641211 CARTON 0615 313811708641 HEX CODE OF F/W(NO MATL REQ) 1054 313815864691 TUNER PCB ASSY(CHINA) 1057 313815864811 SCALER PCB ASSY (32-CHINA) 1172 313818871651 MAINSCORD CCEE 10A 1M8 DET BK 1185 823827718111 LSP BOX 8R 10W-L/R(P302HS) 1255 313815864821 CPU ASSY (LG-CHINA) 1256 313815864831 EEPROM ASSY (LG-CHINA) 1691 242202505577 SOC SUBD H 9P M 1211 Y 1692 313914723781 FRONTEND FQ1256/I H-5 2021 203803511407 ELCAP REA 35V S 100U PM20 B 2691 222224119876 CER2 1206 Y5V 10V 10U P8020 R 2692 222224119876 CER2 1206 Y5V 10V 10U P8020 R 3069 212255000177 VDR DC 1MA/459V S MAX 845V R 3691 212211805635 RST SM 0603 RC0603 10R PM5 R 3692 232270260101 RST SM 0603 RC21 100R PM5 R 3693 232270260101 RST SM 0603 RC21 100R PM5 R 5691 242254945579 IND FXD 1206 EMI 100MHZ 100R R 5692 242254945579 IND FXD 1206 EMI 100MHZ 100R R Diversity of 320WN6QS/97 compared with BDL3221V/00 Item 12NC Description 863900016308 320WN6QS/97 0030 313815760031 FRONT BEZEL ASSY(S) 0032 313815416681 FRONT CORNER-B/R(10709) 0033 313815416671 FRONT CORNER-T/R(10709) 0126 313815567801 RATING LABEL 0231 313815137371 TV CASE 0232 313815137391 TV COVER 0236 313815567731 RATING LABEL 0291 313815567701 LABEL(LG-AP) 0292 313815567701 LABEL(LG-AP) 0456 313815641211 CARTON 0615 313811708621 HEX CODE OF F/W(NO MATL REQ) 1054 313815862311 TUNER PCB ASSY(AP) 1057 313815864751 SCALER ASSY (32-AP) 1172 313818871672 MAINSCORD UK 10A 1M8 DET BK 1185 823827718111 LSP BOX 8R 10W-L/R(P302HS) 1255 313815864761 CPU ASSY (LG-AP) 1256 313815864771 EEPROM ASSY (LG-AP) 1691 242202505577 SOC SUBD H 9P M 1211 Y 1692 313914723811 FRONTEND FQ1216PN/I H-5 2691 222224119876 CER2 1206 Y5V 10V 10U P8020 R 2692 222224119876 CER2 1206 Y5V 10V 10U P8020 R 3069 212255000177 VDR DC 1MA/459V S MAX 845V R 3691 212211805635 RST SM 0603 RC0603 10R PM5 R 3692 232270260101 RST SM 0603 RC21 100R PM5 R 3693 232270260101 RST SM 0603 RC21 100R PM5 R 5691 242254945579 IND FXD 1206 EMI 100MHZ 100R R 5692 242254945579 IND FXD 1206 EMI 100MHZ 100R R 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 109 Go to cover page BDL3221 LCD/TV All units that are returned for service or repair must pass the original manufactures safety tests. Safety testing requires both Hipot and Ground Continuity testing. HI-POT TEST INSTRUCTION 1.Application requirements 2. Test method 1.1 All mains operated products must pass the Hi-Pot test as described in this instruction. 1.2 This test must be performed again after the covers have been refitted following the repair, inspection or modification of the product. 2.1 Connecting conditions 2.1.1 The test specified must be applied between the parallel- blade plug of the mainscord and all accessible metal parts of the product. 2.1.2 Before carrying out the test, reliable conductive connections must be ensured and thereafter be maintained throughout the test period. 2.1.3 The mains switch(es) must be in the "ON" position. 2.2 Test Requirements All products should be HiPot and Ground Continuity tested as follows: Test 2820VDC 1700VDC Test current: voltage (2000VAC) (1200VAC) 25A,AC Test time: Test time 3 seconds 1 second 3 seconds(min.) (min.) Resistance required: Trip set at 100 uA 5 mA <=0.09+Rohm, current for Max. R is the (Tester) limitation; set resistance of at 0.1 uA for the mains cord. Min. Limitation Ramp set at 2 time seconds (Tester) Condition HiPot Test for HiPot Test for Ground Continuity products where products where Test requirement the mains input the mains input is range is Full 110V AC(USA range(or 220V type) AC) 2.2.1 The minimum test duration for Quality Control Inspector must be 1 minute. 2.2.2 The test voltage must be maintained within the specified voltage + 5%. 2.2.3 There must be no breakdown during the test. 2.2.4 The grounding blade or pin of mains plug must be conducted with accessible metal parts. 3. Equipments and Connection 3.1. Equipments For example : - ChenHwa 9032 PROGRAMMABLE AUTO SAFETY TESTER - ChenHwa 510B Digital Grounding Continuity Tester - ChenHwa 901 (AC Hi-pot test), 902 (AC, DC Hi-pot test) Withstanding Tester 3.2. Connection 4. Recording Hipot and Ground Continuity testing records have to be kept for a period of 10 years. * Turn on the power switch of monitor before Hipot and Ground Continuity testing. Connect the "video cable" or "grounding screw" to the CLIP on your tester. Video cable (Rear view of monitor) Connect the power cord to the monitor. Grounding screw Power outlet (ChenHwa 9032 tester) Clip Clip Safety Test Requirements 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网 TELEVISION/MONITOR SAFFTY GUIDELINES FOR THE PROFESSIONAL SERVICE TECHNICIAN Safety Checks Fire and Shock Hazard Implosion X-radiation After the original service problem has been corrected,a complete safety check should be made. Be sure to check over the entire set, not just the areas where you have worked. Some previous servicer may have left an unsafe condition,which could be unknowingly passed on to your customer. Be sure to check all of the following: 1. Be sure all components are positioned in such a way as to avoid the possibility of adjacent component shorts. This is especially important on those chassis which are transported to and from the service shop. 2. Never release a repaired unit unless all protective devices such as insulators, barries, covers, strain reliefs, and other hardware have been installed in accordance with the original design. 3. Soldering and wiring must be inspected to locate possible cold solder joints,solder splashes,sharp solder points, frayed leads, pinched leads, or damaged insulation ( including the ac cord).Be certain to remove loose solder balls and all other loose foreign particles. 4. Check across-the-line components and other components for physical evidence of damage or deterioration and replace if necessary. Follow original layout,lead length, and dress. 5. No lead or component should touch a receiving tube or a resistor rated at 1 watt or more. Lead tension around protruding metal surfaces or edges must be avoided. 6. Critical components having special safety characteristics are identified with ans by the Ref. No. in the parts list and enclosed within a broken line * (where several critical components are grouped in one area) along with the safety symbols on the schematic diagrams and/or exploded views. 7. When servicing any unit, always use a separate isolation transformer for the chassis Failure to use a separate isolation transformer may expose you to possible shock hazard, and may cause damage to servicing instruments. 8. Many electronic products use a polarized ac line cord (one wide pin on the plug.) Defeating this safety feature may create a potential hazard to the service and the user. Extension cords which do not incorporate the polarizing feature should never be used. 9. After reassembly of the unit, always perform an leakage test or resistance test from the line cord to all exposed metal parts of the cabinet. Also check all metal control shafts(with knobs removed), antenna terminals, handles, screws, etc. to be sure the unit may be safety operated without danger of electrical shock. * Broken line 1. All picture tubes used in current model receivers are equipped with an integral implosion system. Care should always be used, and safety glasses worn,whenever handling any picture tube. Avoid scratching or otherwise damaging the picture tube during installation. 2. Use only replacement tubes specified by the manufacturer. 1. Be sure procedures and instructions to all your service personnel cover the subject of X-radiation. Potential sources of X-rays in TV receivers are the picture tube and the high voltage circuits. The basic precaution which must be exercised is to keep the high voltage at the factory recommended level. 2. To avoid possible exposure to X-radiation and electrical shock, only the manufacturer's specified anode connectors must be used. 3. It is essential that the service technician has an accurate HV meter available at all times. The calibration of this meter should be checked periodically against a reference standard. 4. When the HV circuitry is operating properly there is no possibility of an x- radiation problem. High voltage should always be kept at the manufacturer's rated value-no higher - for optimum performance. Every time a color set is serviced, the brightness should be run up and down while monitoring the HV with a meter to be certain that the HV is regulated correctly and does not exceed the specified value. We suggest that you and your technicians review test procedures so that HV and HV regulation are always checked as a standard servicing procedure, and the reason for this prudent routine is clearly understood by everyone. It is important to use an accurate and reliable HV meter. It is recommended that the HV recorded on each customer's invoice, which will demonstrate a proper concern for the customer's safety. 5. When troubleshooting and making test measurements in a receiver with a problem of excessive high voltage, reduce the line voltage by means of a Variac to bring the HV into acceptable limits while troubleshooting. Do : : WARNING OFF SERVICE NOTE Before removing the CRT anode cap, turn the unit and short the HIGH VOLTAGE to the CRT DAG ground. The CRT DAG is not at chassis ground. 6. New picture tubes are specifically designed to withstand higher operathng voltages without creating undesirable X-radiation. It is strongly recommended that any shop test fixture which is to be used with the new higher voltage chassis be equipped with one of the new type tubes designed for this service. Addition of a permanently connected HV meter to the shop test fixture is advisable. The CRT types used in these new sets should never be replaced with any other types, as this may result in excessive X-radiation. 7. It is essential to use the specified picture tube to avoid a possible X-diation problem. 8. Most TV receivers contain some type of emergency "Hold Down" circuit to prevent HV from rising to excessive levels in the presence of a failure mode. These various circuits should be understood by all technicians servicing them, especially since many hold down circuits are inoperative as long as the receiver performs normally. 1. Unplug the ac line cord and connect a jumper between the two prongs of the plug. 2. Turn on the power switch. 3. Measure the resistance value between the jumpered ac plug and all exposed cabinet parts of the receiver, such as screw heads, antennas, and control shafts. When the exposed metallic part has a return path to the chassis, the reading should be between 1 megohm and 5.2 megohms. When the exposed metal does not have a return path to the chassis, the reading must be infinity. Remove the jumper from the ac line cord. 1. Do not use an isolation transformer for this test. Plug the completely reassembled receiver directly into the ac outlet. 2. Connect a 1.5k, 10w resistor paralleled by a 0.15uf. capacitor between each exposed metallic cabinet part and a good earth ground such as a water pipe, as shown above. 3. Use an ac voltmeter with at least 5000 ohms volt sensitivity to measure the potential across the resistor. 4. The potential at any point should not exceed 0.75 volts. A leakage current tester may be used to make this test; leakage current must not exceed 0.5 milliamps. If a measurement is outside of the specified limits, there is a possibility of shock hazard. The receiver should be repaired and rechecked before returning it to the customer. 5. Repeat the above procedure with the ac plug reversed.( Note: An ac adapter is necessary when a polarized plug is used. Do not defeat the polarizing feature of the plug.) The primary source of X-radiation in this television receiver is the picture tube. The picture tube utilized in this chassis is specially constructed to limit X-radiation emissions. For continued X-radiation protection, the replacement tube must be the same type as the original, including suffix letter, or a Philips approved type. Many electrical and mechanical parts in Philips television sets have special safety related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. The use of a substitute part which does not have the same safety characteristics as the Philips recommended replacement part shown in this service manual may create shock, fire, or other hazards Leakage Current Cold Check Leakage Current Hot Check Picture Tube Replacement Parts Replacement 1500 ohm, 10W 0.15 uF WATER PIPE EARTH GROUND TO INSTRUMENTS EXPOSED METAL PARTS 家电维修资料网 www. 520101. com www. 520101. com 家电维修资料网