www.philips.com/welcome BDL4271VL BDL4671VL BDL5571VL User Manual (English) BDL4271VL / BDL4671VL / BDL5571VL ii Safety Instructions Warnings and Precautions KNOW THESE SAFETY SYMBOLS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product. Note to CATV system installers: This reminder is provided to call CATV system installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. CAUTION: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to operate it. CAUTION: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug. IMPORTANT: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement of U.S. copyright laws. Certain Canadian programs may also be copyrighted and any unauthorized recording in whole or in part may be in violation of these rights. TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The Socket-outlet should be installed near the apparatus and be easily accessible. Read and follow these instructions when connecting and using your Public Information Display: • Unplug the display if you are not going to use it for an extensive period of time. • Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids. • Consult a service technician if the display does not operate normally when you have followed the instructions in this manual. • The casing cover should be opened only by qualified service personnel. • Keep the display out of direct sunlight and away from stoves or any other heat sources. • Remove any object that could fall into the vents or prevent proper cooling of the display’s electronics. • Do not block the ventilation holes on the cabinet. • Keep the display dry. To avoid electric shock, do not expose it to rain or excessive moisture. • If turning off the display by detaching the power cable, wait for 6 seconds before re-attaching the power cable for normal operation. • To avoid the risk of shock or permanent damage to the set do not expose the display to rain or excessive moisture. • When positioning the display, make sure the power plug and outlet are easily accessible. • IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast remains on the screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of the screen. This is a well-known phenomenon that is caused by the shortcomings inherent in LCD technology. In most cases the afterimage will disappear gradually over a period of time after the power has been switched off. Be aware that the after-image symptom cannot be repaired and is not covered under warranty. BDL4271VL / BDL4671VL / BDL5571VL iii Regulatory Information CE Declaration of Conformity We declare under our responsibility that the product is in conformity with the following standards: • EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment) • EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment) • EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment) • EN61000-3-2:2006 (Limits for Harmonic Current Emission) • EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable • 2006/95/EC (Low Voltage Directive) • 2004/108/EC (EMC Directive) • 2005/32/EC (EuP, Energy-using Product Directive) EC No. 642/2009 Implementing • 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on ISO9000 level. Federal Communications Commission (FCC) Notice (U.S. Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device. To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture. THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT REGULATIONS. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. BDL4271VL / BDL4671VL / BDL5571VL iv Polish Center for Testing and Certification Notice The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, display, printer, and so on) should have the same power supply source. The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible. A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/ E-06251. Electric, Magnetic and Electronmagnetic Fields (“EMF”) 1. We manufacture and sell many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive electromagnetic signals. 2. One of our leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products. 3. We are committed to develop, produce and market products that cause no adverse health effects. 4. We confirm that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available today. 5. We play an active role in the development of international EMF and safety standards, enabling us to anticipate further developments in standardization for early integration in its products. BDL4271VL / BDL4671VL / BDL5571VL v Information for U.K. only (A) (B) WARNING - THIS APPLIANCE MUST BE EARTHED. Important: This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. NOTE: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere. How to connect a plug The wires in the mains lead are coloured in accordance with the following code: BLUE - “NEUTRAL” (“N”) BROWN - “LIVE” (“L”) GREEN & YELLOW - “EARTH” (“E”) 1. The GREEN & YELLOW wire must be connected to the terminal in the plug which is marked with the letter “E” or by the Earth symbol or coloured GREEN or GREEN & YELLOW. 2. The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured BLACK. 3. The BROWN wire must be connected to the terminal which marked with the letter “L” or coloured RED. Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires. BDL4271VL / BDL4671VL / BDL5571VL vi China RoHS 中国电子信息产品污染控制标识要求 (中国RoHS法规标示要求) 产品中有毒有害物质或元素 的名称及含量 部件名称 有毒有害物质或元素 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr 6+) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) 外壳 O O O O O O 液晶面板 X X O O O O 电路板组件 X O O O O O 附件 (遥控器，电源线，连接线) X O O O O O 遥控器电池 X O O O O O O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下. X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求. 10 環保使用期限 此標識指期限(十年)，電子信息產品中含有的有毒有害物質或元素在正常使用的條件下不會發生外泄或突變 ，電子信息產品用戶使用該電子信息產品不會對環境造成嚴重污染或對其人身、財產造成嚴重損害的期限。 BDL4271VL / BDL4671VL / BDL5571VL vii North Europe (Nordic Countries) Information Placering/Ventilation VARNING: FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. Placering/Ventilation ADVARSEL: SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE. Paikka/Ilmankierto VAROITUS: SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA. Plassering/Ventilasjon ADVARSEL: NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ. End-of-Life Disposal Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of. Please find out about the local regulations on how to dispose of your old display from your local Philips dealer. (For customers in Canada and U.S.A.) This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling contact www.eia.org (Consumer Education Initiative) Waste Electrical and Electronie Equipment-WEEE Attention users in European Union private households This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household or the store at which you purchased the product. Attention users in United States: Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling information, contact: www.mygreenelectronics.com or www.eiae.org. End of Life Directives-Recycling Your new Public Information Display contains several materials that can be recycled for new users. Like all LCD produces, this set contains a lamp with Mercury. Please dispose of according to all Local, State, and Federal laws. As an ENERGY STAR Partner, we have determined that this product meets the ENERGY STAR guidelines for energy efficiency. BDL4271VL / BDL4671VL / BDL5571VL viii Table Of Contents 3.5.1. Display control connection ..............13 3.5.2. Digital video connection ....................13 3.5.3. Analog video connection ..................13 3.6. Connecting USB device .....................................14 4. OSD Menu ..............................................................16 4.1. Navigating the OSD Menu .............................16 4.1.1. Navigating the OSD menu using the remote control........................................16 4.1.2. Navigating the OSD menu using the display’s control buttons ....................16 4.2. OSD Menu Overview ........................................16 4.2.1. Picture menu ............................................16 4.2.2. Screen menu ............................................17 4.2.3. Audio menu ..............................................18 4.2.4. PIP menu ....................................................18 4.2.5. Configuration1 menu ..........................19 4.2.6. Configuration2 menu ..........................20 4.2.7. Advanced option menu .....................20 5. Input Mode ..............................................................24 6. Pixel Defect Policy .................................................25 6.1. Pixels and Sub-Pixels ............................................25 6.2. Types of Pixel Defects + Dot Definition .25 6.3. Bright Dot Defects ...............................................25 6.4. Dark Dot Defects .................................................26 6.5. Proximity of Pixel Defects ................................26 6.6. Pixel Defect Tolerances ......................................26 6.7. MURA ..........................................................................26 7. Cleaning and Troubleshooting .............................27 7.1. Cleaning ......................................................................27 7.2. Troubleshooting ......................................................28 8. Technical Specifications ........................................29 8.1. BDL4271VL ..............................................................29 8.2. BDL4671VL ..............................................................31 8.3. BDL5571VL ..............................................................33 1. Unpacking and Installation .....................................1 1.1. Unpacking .....................................................................1 1.2. Package Contents .....................................................1 1.3. Installation Notes ......................................................1 1.4. Installing and Removing Table Stands (optional) .......................................................................2 1.5. Mounting on a Wall .................................................3 1.5.1. VESA Grid ....................................................3 1.6. Mounting in Portrait Position .............................4 1.6.1. How to use the logo guider for portrait position ........................................4 1.6.2. How to remove the logo .....................4 2. Parts and Functions ................................................. 5 2.1. Control Panel ..............................................................5 2.2. Input/Output Terminals .........................................6 2.3. Remote Control ........................................................7 2.3.1. General functions .....................................7 2.3.2. Inserting the batteries in the remote control.............................................................8 2.3.3. Handling the remote control .............8 2.3.4. Operating range of the remote control.............................................................8 3. Connecting External Equipment ..........................9 3.1. Using the Switch Cover ........................................9 3.2. Connecting External Equipment (DVD/ VCR/VCD) ................................................................10 3.2.1. Using COMPONENT video input ..............................................................10 3.2.2. Using HDMI video input ...................10 3.3. Connecting a PC ....................................................11 3.3.1. Using VGA input .....................................11 3.3.2. Using DVI input ......................................11 3.3.3. Using HDMI input .................................11 3.4. Connecting Audio Equipment ........................12 3.4.1. Connecting external speakers........12 3.4.2. Connecting an external audio device ...........................................................12 3.5. Connecting Multiple Displays in a Daisy- chain Configuration ..............................................13 BDL4271VL / BDL4671VL / BDL5571VL 1 1. Unpacking and Installation 1.1. Unpacking • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • Due to the size and weight of this display it is recommended for two people to move it. • After opening the carton, ensure that the contents are complete and in good condition. 1.2. Package Contents Please verify that you received the following items with your package content: • LCD display • CD ROM • Remote control with AAA batteries • Power cord (1.8 m) • VGA cable (1.8 m) • RS232 cable (3 m) • Quick Installation Guide • Power switch cover • Screw for Power switch cover (M3x8) • BNC-to-RCA adapter (x3) • Logo guider * The supplied power cord varies depending on destination. For EU For China For North America For UK POWER SMART VIDEO SOURCE PIP INPUT ON/OFF CHANGE BRIGHTNESS CONTRAST DISPLAY AUTO ADJUST MUTE VOL UP VOL DOWN EXIT MENU SET AUDIO SOURCE USB MENU Remote Control and AAA Batteries Video Signal Cable (D-SUB to D-SUB Cable) Logo guider CD ROM Power switch cover and screw (M3x8) x1 BNC-RCA adapter x3 RS232 Cable NOTES: • For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and complies with the safety regulations of the particular country. • You might like to save the package box and packing material for shipping the display. 1.3. Installation Notes • Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your service agent. • The product should be installed on a flat surface to avoid tipping. The distance between the back of the product and the wall should be maintained for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life of the electronic components. • The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m, some abnormalities may be experienced. BDL4271VL / BDL4671VL / BDL5571VL 2 1.4. Installing and Removing Table Stands (optional) To install table stands: 1. Ensure your display is powered off. 2. Spread a protective sheet on a flat surface. 3. Grab the carrying handles and place the display face-down on the protective sheet. 4. After inserting the stand in the guide block, tighten the screws on both sides of the display. NOTE: The longer side of the stand should face the front of the display. Carrying handle Thumbscrews Longer portions face the front Table stand To remove table stands: 1. Power off the display. 2. Spread a protective sheet on a flat surface. 3. Grab the carrying handles and place the display face-down on the protective sheet. 4. Remove screws using a screwdriver and place them in a safe place for reuse. BDL4271VL / BDL4671VL / BDL5571VL 3 1.5. Mounting on a Wall To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface that complies with TUV-GS and/or UL1678 standard in North America. Protective Sheet VESA Grid Tabletop stand Table 1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the screen face. 2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc). 3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation. 4. For the wall-mounting kit, use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them securely. 1.5.1. VESA Grid BDL4271VL 400(H) x 200(V) mm 200(H) x 200(V) mm BDL4671VL / BDL5571VL 400(H) x 400(V) mm 400(H) x 200(V) mm 200(H) x 200(V) mm Caution: To prevent the display from falling: • For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially available. For detailed installation instructions, refer to the guide received with the respective bracket. • To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other natural disaster, be sure to consult the bracket manufacturer for installation location. Ventilation Requirements for enclosure locating To allow heat to disperse, leave space between surrounding objects as shown in the diagram below. 100 mm 100 mm 100 mm 100 mm BDL4271VL / BDL4671VL / BDL5571VL 4 1.6. Mounting in Portrait Position This display can be installed in portrait position. 1. Remove the table stand, if attached. 2. Rotate 90 degrees clockwise. The “ ” logo should be on the LEFT side when facing the display. 90 90 1.6.1. How to use the logo guider for portrait position 1. Put the guider on the lower-left corner of the front bezel of the display. Fold down both of its edges. 2. Peel off the protective film at the back of the “ ” logo sticker. Hold and press the guider with your left hand. Put the “ ” logo sticker with its adhesive side down into the logo hole with your right hand, and press to make it stick tightly onto the front bezel. 3. Remove the guider. 1 2 3 1.6.2. How to remove the logo 1. Prepare a piece of paper with a cutting area of logo as a protector to prevent the front bezel from scratching. 2. Using a knife, carefully remove the logo sticker with the paper placing beneath. 3. Tear off the logo sticker. 1 2 3 NOTE: When installing the display on a wall, please consult a professional technician for proper installation. We accept no liability for installations not performed by a professional technician. BDL4271VL / BDL4671VL / BDL5571VL 5 2. Parts and Functions 2.1. Control Panel 1 2 3 4 5 6 7 8 MUTE INPUT MENU 9 1 POWER button Use this button to turn the display on or put the display to standby. 2 MUTE button Switch the audio mute ON/OFF. 3 INPUT button • Use this button to select the input source. 4 [ ] button Increase the adjustment while OSD menu is on, or increase the audio output level while OSD menu is off. • Used as [SET] button in the On-Screen-Display menu, 5 [ ] button Decrease the adjustment while OSD menu is on, or decrease the audio output level while OSD menu is off. 6 [ ] button Move the highlight bar up to adjust the selected item while OSD menu is on. 7 [ ] button Move the highlight bar down to adjust the selected item while OSD menu is on. 8 MENU button Return to previous menu while OSD menu is on, or to activate the OSD menu when OSD menu is off. NOTE: “Keyboard Control Lock Mode” This function completely disables the access to all Keyboard Control functions. To enable or disable the keyboard control lock, press both [ ] and [ ] buttons and hold down continuously for more than 3 (three) seconds. 9 Remote control sensor and power status indicator • Receives command signals from the remote control. • Indicates the operating status of the display without OPS: - Lights green when the display is turned on - Lights red when the display is in standby mode - Lights amber when the display enters APM mode - When {SCHEDULE} is enabled, the light blinks green and red - If the light blinks red, it indicates that a failure has been detected - Lights off when the main power of the display is turned off • Indicates the operating status of the display with OPS: - Lights green when the display is on, but the OPS is off - Lights blue when the display and the OPS is on - Lights red when the display is in standby mode - Lights amber when the display enters APM mode - When {SCHEDULE} is enabled, the light blinks green and red - If the light blinks red, it indicates that a failure has been detected - Lights off when the main power of the display is turned off BDL4271VL / BDL4671VL / BDL5571VL 6 2.2. Input/Output Terminals 1 2 3 4 5 6 7 8 13 9 10 11 12 14 15 16 17 18 19 1 AC IN AC power input from the wall outlet. 2 MAIN POWER SWITCH Switch the main power on/off. 3 AC OUT AC power supply to the AC IN jack of a media player. 4 USB Connect your USB storage device. 5 RS232C OUT RS232C network output for the loop-through function. 6 RS232C IN RS232C network input for the loop-through function. 7 RJ-45 LAN port connection from your OPS device. 8 HDMI IN HDMI video/audio input. 9 DisplayPort DisplayPort video input. 10 DVI IN DVI-D video input. 11 DVI OUT / VGA OUT DVI or VGA video output. 12 VGA IN (D-Sub) VGA video input. 13 VGA AUDIO IN Audio input for VGA source (3.5mm stereo phone). 14 COMPONENT IN (BNC) Component YPbPr video source input. 15 SPEAKER SWITCH Internal speaker on/off switch. 16 AUDIO IN Audio input from external AV device (RCA). 17 AUDIO OUT (RCA) Audio output from the AUDIO IN jack to an external AV device. 18 SPEAKERS OUT External speakers output. 19 KENSINGTON LOCK Used for security and theft prevention. BDL4271VL / BDL4671VL / BDL5571VL 7 2.3. Remote Control 2.3.1. General functions POWER SMART VIDEO SOURCE PIP INPUT ON/OFF CHANGE BRIGHTNESS CONTRAST DISPLAY AUTO ADJUST MUTE VOL UP VOL DOWN EXIT MENU SET AUDIO SOURCE USB MENU 1 10 11 12 13 14 15 16 17 18 19 20 2 3 4 5 6 7 8 9 21 1 [POWER] button Press to switch on the display from standby mode. Press again to turn it off and back into standby mode. 2 [SMART] button Press to activate Smart Menu. Press [ ] or [ ] button to select menu options. Press [SET] button to confirm and exit the selection. • Standard: Used for normal images (factory setting) • Highbright: Used for moving image such as Video • sRGB: Used for text based images 3 [PIP] (Picture In Picture) button [ON/OFF]: Turn PIP mode ON/OFF. [INPUT]: Select the input signal for the sub-picture. [CHANGE]: Toggle between the main picture and sub picture. 4 [CONTRAST] button Press to activate Contrast Menu. Press [ ] or [ ] button to adjust the value. Press [MENU] button to confirm and exit. 5 [DISPLAY] button Press to turn on/off the information OSD displayed on the upper right corner of the screen. 6 [ ] button • Press to move the selection left in OSD menu. • Press to decrease the value in OSD menu. • Press to move the sub-picture left in PIP mode. 7 [SET] button Press to activate the setting inside the OSD menu. 8 [AUTO ADJUST] button Press to run the Auto Adjust function. NOTE: This button is functional for VGA input only. 9 [MUTE] button Press to turn the mute function on/off. 10 [VIDEO SOURCE] button Press to toggle Video Source Menu. Press [ ] or [ ] button to select one of the video sources among Displayport, DVI-D, VGA, HDMI, Component, Video, Card OPS, or USB. Press [SET] button to confirm and exit. 11 [AUDIO SOURCE] button Press to toggle Audio Source Menu. Press [ ] or [ ] button to select one of the audio sources among Displayport, HDMI, Audio1, Audio2, USB, or Card OPS. Press [SET] button to confirm and exit. 12 Picture Format button Press to switch screen aspect ratio. • For PC signal: FULL, NORMAL, CUSTOM, and REAL. • For Video signal: FULL, NORMAL, DYNAMIC, CUSTOM, REAL, and 21:9. 13 [BRIGHTNESS] button Press to toggle Brightness Menu. Press [ ] or [ ] button to adjust the value. Press [MENU] button to confirm and exit. 14 [ ] button • Press to move the selection up in OSD menu. • Press to move the sub-picture up in PIP mode. 15 [MENU] button Press to turn the OSD menu on/off. 16 [ ] button • Press to move the selection right in OSD menu. • Press to increase the value in OSD menu. • Press to move the sub-picture right in PIP mode. 17 [EXIT] button Press to turn back to the previous OSD menu. 18 [ ] button • Press to move the selection down in OSD menu. • Press to move the sub-picture down in PIP mode. 19 [VOL UP] button Press to increase the audio output level. 20 [VOL DOWN] button Press to decrease the audio output level. 20 [USB MENU] button Press to enter the USB menu for the USB input. BDL4271VL / BDL4671VL / BDL5571VL 8 2.3.2. Inserting the batteries in the remote control The remote control is powered by two 1.5V AAA batteries. To install or replace batteries: 1. Press and then slide the cover to open it. 2. Align the batteries according to the (+) and (–) indications inside the battery compartment. 3. Replace the cover. Caution: The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions: • Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment. • Do not mix battery types. • Do not combine new batteries with used ones. It causes shorter life or leakage of batteries. • Remove the dead batteries immediately to prevent them from liquid leaking in the battery compartment. Don’t touch exposed battery acid, as it can damage your skin. NOTE: If you do not intend to use the remote control for a long period, remove the batteries. 2.3.3. Handling the remote control • Do not subject to strong shock. • Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately. • Avoid exposure to heat and steam. • Other than to install the batteries, do not open the remote control. 2.3.4. Operating range of the remote control Point the top of the remote control toward the display’s remote control sensor when pressing a button. Use the remote control within a distance of less than 10m/33ft from the display’s sensor, and a horizontal and vertical angle of less than 30 degrees. NOTE: The remote control may not function properly when the remote control sensor on the display is under direct sunlight or strong illumination, or when there is an obstacle in the path of signal transmission. 30 30 POWER SMART VIDEO SOURCE PIP INPUT ON/OFF CHANGE BRIGHTNESS CONTRAST DISPLAY AUTO ADJUST MUTE VOL UP VOL DOWN EXIT MENU SET AUDIO SOURCE USB MENU BDL4271VL / BDL4671VL / BDL5571VL 9 3. Connecting External Equipment 3.1. Using the Switch Cover A cover for the power switch is provided to prevent the display from being turned on or off accidentally. To lock the cover into position: 1. Align and insert the cover to the indentation located beside the power switch. 2. Use the screw to lock the cover. BDL4271VL / BDL4671VL / BDL5571VL 10 3.2. Connecting External Equipment (DVD/VCR/VCD) 3.2.1. Using COMPONENT video input DVD / VCR / VCD [AUDIO IN] [COMPONENT IN] (YPbPr) COMPONENT Out (YPbPr) Audio Out [R] [L] 3.2.2. Using HDMI video input DVD / VCR / VCD HDMI Out [HDMI IN] BDL4271VL / BDL4671VL / BDL5571VL 11 3.3. Connecting a PC 3.3.1. Using VGA input PC [VGA IN] [VGA AUDIO IN] VGA Out D-Sub 15 pin Audio Out [AUDIO IN] [R] [L] 3.3.2. Using DVI input PC [VGA AUDIO IN] DVI Out Audio Out [AUDIO IN] [R] [L] [DVI IN] 3.3.3. Using HDMI input PC HDMI Out [HDMI IN] BDL4271VL / BDL4671VL / BDL5571VL 12 3.4. Connecting Audio Equipment 3.4.1. Connecting external speakers External speakers 3.4.2. Connecting an external audio device Stereo Amplifier [AUDIO OUT] [R] [L] Audio In BDL4271VL / BDL4671VL / BDL5571VL 13 3.5. Connecting Multiple Displays in a Daisy-chain Configuration You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall. NOTE: Maximum 25 displays (5x5) can be used in a daisy-chain configuration. 3.5.1. Display control connection Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2. PC DISPLAY 1 DISPLAY 2 [RS-232C IN] [RS-232C] [RS-232C OUT] [RS-232C IN] 3.5.2. Digital video connection Connect the [DVI OUT / VGA OUT] connector of DISPLAY 1 to the [DVI IN] connector of DISPLAY 2. PC DISPLAY 1 DISPLAY 2 [DVI IN] [DVI] [DVI/VGA OUT] [DVI IN] 3.5.3. Analog video connection Connect the [DVI OUT / VGA OUT] connector of DISPLAY 1 to the [VGA IN] connector of DISPLAY 2. PC DISPLAY 1 DISPLAY 2 [VGA IN] [VGA] [DVI/VGA OUT] [VGA IN] BDL4271VL / BDL4671VL / BDL5571VL 14 3.6. Connecting USB device Your display is fitted with a USB port that enables you to view photos, or play audio and video files stored on a USB storage device. USB Caution: The manufacturer is not responsible if the USB storage device is not supported, nor for any damage or loss of data caused by connecting your USB device. Supported format PHOTO: JPEG, BMP, PNG MUSIC: MP3, AAC, AC3, WAV VIDEO: AVI, MP4, MOV, MPG 5. Press [ ] or [ ] button to move left or right to select your USB source type. Press [SET] button to enter its thumbnail browser to search for your media source to play. 6. While in the thumbnail browser, pressing [USB MENU] button will enter its control submenu.           USB operation 1. Power on the display. 2. Connect the USB device to the USB port on the downward side of your display. 3. Select USB as your video source.            4. The USB main screen appears. Video Music Photo BDL4271VL / BDL4671VL / BDL5571VL 15 Playing photo files 1. Press [ ] or [ ] button to move left or right to select Photo in the USB main screen. Video Music Photo 2. Press [SET] button to enter the photo folder. Folder2 Folder3 Folder1 Photo 01/01 3. Press [ ], [ ], [ ], or [ ] button to move left, right, up, or down to select the photo you want to view in full screen. Press [SET] button to start playing. PHOTO PHOTO PHOTO PHOTO PHOTO Photo /Folder1 01/01 4. Now while the display starts slide showing all the photo files stored in this folder, you can press [USB MENU] button to enter its control submenu.        NOTE: The paused photo can be rotated or zoomed by pressing the [USB MENU] button again and selec Rotate or Zoom. Playing music files 1. Press [ ] or [ ] button to move left or right to select Music in the USB main screen. 2. Press [SET] button to enter the music folder. 3. Press [ ], [ ], [ ], or [ ] button to move left, right, up, or down to select the music you want to play. Press [SET] button to start playing. 4. Now while the display starts slide showing all the music files stored in this folder, you can press [USB MENU] button to enter its control submenu.       Playing video files 1. Press [ ] or [ ] button to move left or right to select Video in the USB main screen. 2. Press [SET] button to enter the video folder. 3. Press [ ], [ ], [ ], or [ ] button to move left, right, up, or down to select the video you want to play. Press [SET] button to start playing. 4. Now while the display starts slide showing all the photo files stored in this folder, you can press [USB MENU] button to enter its control submenu.         Disconnect USB device Caution: Follow this procedure to avoid damage to your USB storage device. 1. Press [EXIT] to exit the USB browser. 2. Change the video source input. 3. Wait for five seconds before disconnecting the USB device. BDL4271VL / BDL4671VL / BDL5571VL 16 4. OSD Menu An overall view of the On-Screen Display (OSD) structure is shown below. You can use it as a reference for further adjusting your display. 4.1. Navigating the OSD Menu 4.1.1. Navigating the OSD menu using the remote control EXIT MENU SET 1. Press [MENU] button on the remote control to display the OSD menu. 2. Press [ ] or [ ] button to choose the item you want to adjust. 3. Press [SET] or [ ] button to enter the submenu. 4. In the submenu, press [ ] or [ ] button to toggle among items, press [ ] or [ ] button to adjust settings. If there is a submenu, press [SET] or [ ] button to enter the submenu. 5. Press [EXIT] button to return to the previous menu, or press [MENU] button to exit the OSD menu. 4.1.2. Navigating the OSD menu using the display’s control buttons 1. Press [MENU] button to display the OSD menu. 2. Press [ ] or [ ] button to choose the item you want to adjust. 3. Press [ ] button to enter the submenu. 4. In the submenu, press [ ] or [ ] button to toggle among items, press [ ] or [ ] button to adjust settings. If there is a submenu, press [ ] button to enter the submenu. 5. Press [MENU] button to return to the previous menu, or press [MENU] button several times to exit the OSD menu. 4.2. OSD Menu Overview 4.2.1. Picture menu Brightness Contrast Sharpness Black level Tint Color Color temperature Color control Smart contrast Smart picture Picture Screen Audio PIP Configuration1 Configuration2 Advanced option Noise reduction Brightness Adjust the overall image brightness by changing the intensity of the LCD panel’s backlight. Contrast Adjust to sharpen the picture quality. The black portions of the picture become richer in darkness and the white become brighter. Sharpness Adjust to improve the image detail. Black level Video black level is defined as the level of brightness at the darkest (black) part of a visual image. Adjust to change the image brightness. Noise reduction Adjust to remove the noise in the image. You can select a suitable noise reduction level. Choose from: {Off} / {Low} / {Medium} / {High}. NOTE: This item is functional for HDMI(Video mode), Video, and YPbPr inputs only. Tint Adjust to change the color tint of the image. Use the [ ] or [ ] button to adjust. Press the [ ] button and the flesh tone color turns slightly green. Press the [ ] button and the flesh tone color turns slightly purple. NOTE: This item is functional for HDMI(Video mode), Video, and YPbPr inputs only. Color Adjust to increase or decrease the intensity of colors in the image. NOTE: This item is functional for HDMI(Video mode),Video and YPbPr inputs only. Color temperature Select a color temperature for the image. A lower color temperature will have a reddish tint, whilst a higher color temperature gives off a more bluish tint. Choose from: {3000K} / {4000K} / {5000K} / {6500K} / {7500K} / {9300K} / {10000K} / {Native} / {User}. Color control With this function you can adjust the color tones of the image precisely by changing the R (Red), G (Green) and B (Blue) settings independently. BDL4271VL / BDL4671VL / BDL5571VL 17 NOTE: This item is functional only when {Color temperature} is set to {User}. Smart contrast When turned on, this function helps enhance image contrast when displaying dark scenes. Smart picture The following smart picture modes are available for: • PC mode: {Standard} / {Highbright} / {sRGB}. • Video mode: {Standard} / {Highbright} / {Cinema}. Video source Select a video input source.            Picture reset Reset all settings in the Picture menu. 4.2.2. Screen menu H position V position Clock Clock phase Custom zoom Screen reset Picture Screen Audio PIP Configuration1 Configuration2 Advanced option Zoom mode H position Press the [ ] button to move the image to the right, or [ ] to move the image to the left. NOTE: This item is functional for all inputs except HDMI, Card OPS, and DP in video mode. V position Press the [ ] button to move the image up, or [ ] to move the image down. NOTE: This item is functional for all inputs except HDMI, Card OPS, and DP in video mode. Clock Adjust the width of the image. NOTE: This item is functional for VGA input only. Clock phase Adjust to improve the focus, clarity and stability of the image. NOTE: This item is functional for VGA input only. Zoom mode The pictures you receive may be transmitted in 16:9 format (wide screen) or 4:3 format (conventional screen). The 16:9 pictures sometimes have a black band at the top and bottom of the screen (letterbox format). This function allows you to optimize the picture display on screen. The following zoom modes are available for: • PC mode: {Full} / {Normal} / {Custom} / {Real}. • Video mode: {Full} / {Normal} / {Dynamic} / {Custom} / {Real} / {21:9}. Full This mode restores the correct proportions of pictures transmitted in 16:9 using the full screen display. Normal The picture is reproduced in 4:3 format and a black band is displayed on either side of the picture. Dynamic Fill the entire screen by stretching 4:3 pictures non-proportionally. Custom Choose to apply the custom zoom settings in the Custom Zoom submenu. Real This mode displays the image pixel-by-pixel on screen without scaling the original image size. 21:9 The picture is enlarged to 16:9 format. This mode is recommended when displaying pictures that have black bands at the top and bottom (letterbox format). Custom zoom You can use this function to further customize the zoom settings to suit the image you want to display. NOTE: This item is functional only when the Zoom mode setting is set to Custom. Zoom Expands the horizontal and vertical sizes of the image simultaneously. H zoom Expands the horizontal size of the image only. V zoom Expands the vertical size of the image only. BDL4271VL / BDL4671VL / BDL5571VL 18 H position Moves the horizontal position of the image left or right. V position Moves the vertical position of the image up or down. Screen reset Reset all settings in the Screen menu to factory preset values. 4.2.3. Audio menu Balance Treble Bass Volume Minimum volume Picture Screen Audio PIP Configuration1 Configuration2 Advanced option Maximum volume Audio source Mute Audio reset Card OPS audio Balance Adjust to emphasize left or right audio output balance. Treble Adjust to increase or decrease higher-pitched sounds. Bass Adjust to increase or decrease lower-pitched sounds. Volume Adjust to increase or decrease the audio output level. Maximum volume Adjust your own limitation for the maximum volume setting. This stops the volume from being playing at too loud a level. Minimum volume Adjust your own limitation for the minimum volume setting. Mute Turn the mute function on/off. Audio source Select the audio input source according to the audio signal source connected to the audio input and HDMI sockets on the display.          Choose from: {HDMI} / {Audio1} / {Audio2} / {Audio3}. Audio reset Reset all settings in the Audio menu to factory preset values. Card OPS audio Select the analog or digital audio mode for card OPS. 4.2.4. PIP menu PIP PIP input PIP change PIP size PIP reset Picture Screen Audio PIP Configuration1 Configuration2 Advanced option PIP audio PIP Select the PIP (Picture-in-Picture) mode. Choose from: {Off} / {PIP} / {POP} / {PBP aspect} / {PBP full}. PIP input Select the input signal for the sub-picture. PIP change Enlarges the smaller picture to become the main picture, and vice versa. PIP size Select the size of the sub picture in the PIP (Picture-in-Picture) mode. Choose from: {Small} / {Medium} / {Large}. PIP audio Select the audio source in the PIP (Picture-in-Picture) mode. • {Main} - Select audio from the main picture • {Sub} - Select audio from the sub picture. PIP reset Reset all settings in the PIP menu to factory preset values. NOTES: • The PIP function is available only for certain signal source combinations as shown in the table below. • The availability of the PIP function will also depend on the resolution of the input signal being used. Main Picture Sub Picture Displayport HDMI DVI-D VGA YPbPr Video USB Card OPS Displayport X X X O O O X X HDMI X X X O O O X X DVI-D X X X O O O X X VGA O O O X X X O O YPbPr O O O X X X O O Video O O O X X X O O USB X X X O O O X X Card OPS X X X O O O X X (O: PIP function available, X: PIP function unavailable) BDL4271VL / BDL4671VL / BDL5571VL 19 By pressing the [PIP ON/OFF] button on the remote control, you can change the mode in the order shown below: PIP POP PBP aspect PBP full Off The resolutions in the PIP and POP modes are configured as follows: PIP SIZE {Small} : 320 x 240 pixels {Medium} : 480 x 320 pixels {Large} : 640 x 480 pixels POP SIZE : 474 x 355 pixels NOTE: The images displayed in the sub picture always fit the PIP sizes shown above irrespective of the aspect ratio of the input image. 4.2.5. Configuration1 menu Switch on state Auto adjust Power save Language Color system Picture Screen Audio PIP Configuration1 Configuration2 Advanced option Panel saving Network control port Network settings Configuration reset Factory reset Switch on state Select the display status used for the next time you connect the power cord. • {Power off} - The display will remain off when the power cord is connected to a wall outlet. • {Forced on} - The display will turn on when the power cord is connected to a wall outlet. • {Last status} - The display will return to the previous power status (on/off/standby) when removing and replacing the power cord. Auto adjust Use this function to automatically optimize the display of VGA input image. NOTE: This item is functional for VGA input only. Power save Use this setting to reduce the power automatically. • {RGB} - Select {On} to let the display enter APM mode when no signal is detected from the HDMI Graphic mode, HDMI, DVI-D, or VGA inputs after three successive cycles. • {VIDEO} - Select {On} to enter power saving mode when no signal is detected from the HDMI Video mode or YPbPr inputs after three successive cycles. Language Select the language used in the OSD menu. The options are: { } / { } / { } / { } / { } / { } / { } / { } / { }. Panel saving Choose to enable the panel saving functions and thus reduce the risk of “image persistence” or “ghost-imaging”. • {Cooling Fan} - Select {On} to turn on the cooling fan all the time. Select {Auto} to turn on/off the cooling fan according to the display’s temperature. NOTES: • The default {Auto} option will start running the cooling fan if the temperature of 65°C (152°F) is reached, and will keep running for 30 minutes after cooling down to the temperature of 62°C (144°F). • A temperature-warning message will be shown on the screen if the temperature reaches 79°C (174°F). All key functions except [Power] key will then be disabled. • Once the temperature reaches 80°C (176°F), the display power will be shut down automatically. • {Brightness} - Select {On} and the image brightness will be reduced to an appropriate level. The Brightness setting in the Picture menu will be unavailable when selected. • {Pixel shift} - Select the time interval ({Auto} / {10 ~ 900} Seconds / {Off}) for the display to slightly expand the image size and shift the position of pixels in four directions (up, down, left, or right). Color system Selects the Color System depending on your input video format. The options are: {Auto} / {NTSC} / {PAL} / {SECAM} / {4.43NTSC} / {PAL-60}. NOTE: This item is functional for VIDEO input only. Network control port Select the network control port. Choose from: {RS232} / {LAN(RJ45)} / {Card OPS RS232}. NOTES: • If {LAN(RJ45)} is selected, then {RS232} will not be activated, even if a cable is attached, and vice versa. • The option {Card OPS RS232} is functional after connected with your OPS device. Network settings Assign {IP address}, {Subnet Mask}, and {Default gateway} for the display. Network settings Network host name DHCP IP address Subnet mask Default gateway Login user name Login password 9 172 255 0 0 0 - - - a d m i n 0 [ SET ] change [SET] in STORE Z Disable 16 255 0 0 L - - - 0 0 0 0 1 0 0 - - - • DHCP - Choose to enable or disable the DHCP function. If enabled, the display will be assigned IP address, Subnet mask and Default gateway automatically. If disabled, you will be prompted to enter the following values manually. When finished, press [SET] button to store and save the chosen values. BDL4271VL / BDL4671VL / BDL5571VL 20 • IP address • Subnet mask • Default gateway • Login user name (The default user name is {admin}) • Login password (The default password is {0000}) Configuration reset Reset all settings in Configuration1 menu to the factory preset values. Factory reset Reset all settings in the OSD menus of {Picture}, {Screen}, {Audio}, {PIP}, {Configuration1}, {Configuration2}, and {Advanced option} to the factory preset values. Press [ ] or [ ] button to select [Reset], and then press [SET] button to do the reset. Factory reset Cancel Reset 4.2.6. Configuration2 menu OSD turn off Information OSD Off timer OSD H-position Monitor information Picture Screen Audio PIP Configuration1 Configuration2 Advanced option OSD V-position OSD turn off Set the period of time the OSD (on-screen display) menu stays on the screen. The options are: {5 ~ 120} seconds. Information OSD Set the period of time the information OSD is displayed on the upper right corner of the screen. The information OSD will display when input signal is changed. The information OSD will remain on the screen with {Off} selection. The options are: {1 ~ 60} seconds. Off Timer Set the display to turn itself off to standby mode within an amount of time specified. The options are: {Off, 1 ~ 24} hours from currrent time. NOTE: When the “Off timer” is activated, the “Schedule” settings will be disabled. OSD H-position Adjust the horizontal position of the OSD menu. OSD V-position Adjust the vertical position of the OSD menu. Monitor information Shows information about your display, including model number, serial number, operating hours and software version. Monitor information Model name: Serial no: Operation hours: SW Version: BDL4671VL VER 0.204 0 H 3M 4.2.7. Advanced option menu Input resolution Black level expansion Gamma selection Scan mode Film mode IR control Keyboard control Tiling Heat status Date and time Picture Screen Audio PIP Configuration1 Configuration2 Advanced option Scan conversion Input resolution Set the resolution of the VGA input. This is only required when the display is unable to detect the VGA input resolution correctly. NOTE: This item is functional for VGA input only. The options are: • {1024x768 / 1280x768 / 1360x768} • {1400x1050 / 1680x1050} • {1600x1200 / 1920x1200} • {Auto}: Determines the resolution automatically. The selected settings will become effective after turning off the power and turning it on again. Black level expansion This feature offers deeper blacks for an even better image quality. The options are: {Off} / {Low} / {Medium} / {High}. NOTE: This item is functional for Video mode input only. Gamma selection Gamma is what controls the overall brightness of an image. Images which are not corrected properly can appear too white or too dark, so controlling the gamma properly can have a huge influence on the overall picture quality of your display. The options are: {Native} / {2.2} / {2.4} / {S gamma}. Scan mode Change the display area of the image. • {Overscan} - Display about 95% of the original size of the image. The rest of the areas surrounding the image will be cut off. • {Underscan} - Display the image in its original size. NOTE: This item is functional for Video mode input only. BDL4271VL / BDL4671VL / BDL5571VL 21 Scan conversion Choose to enable or disable the IP (Interlace to Progressive) conversion function. • {Progressive} - Enable the IP conversion function (recommended). Once enabled, the interlace input signal will be converted to progressive format for better display quality. • {Interlace} - Disable the IP function. This mode is suitable for displaying motion pictures, but it increases the chance of image retention. Film mode Choose to turn on or off the film mode frame conversion function. • {Auto} - Enable the film mode frame conversion function for movies and motion pictures. The display converts a 24 frames-per- second (24 fps) input signal format to DVD video signal format. Once this function is enabled, it is recommended that you set the {Scan conversion} function to {Progressive}. • {Off} - Disable the film mode frame conversion function. This mode is suitable for TV broadcasting and VCR signals. IR control Select the operation mode of the remote control when multiple displays are connected via an RS232C connection. • {Normal} - All displays can be operated normally by the remote control unit. • {Primary} - Designate this display as the primary display for remote control operation. Only this display can be operated by the remote control. • {Secondary} - Designate this display as the secondary display. This display can not be operated by the remote control, and will only receive the control signal from the primary display via the RS232C connection. • {Lock All} / {Lock all but Volume} / {Lock all but Power} - Lock the remote control function of this display. To unlock, press and hold the [DISPLAY] button on the remote control for 5 (five) seconds.. Keyboard control Choose to enable or disable the display keyboard (control buttons) function. • {Unlock} - Enable the keyboard function. • {Lock All} / {Lock all but Volume} / {Lock all but Power} - Disable the keyboard function. Tiling With this function you can create a single large-screen matrix (video wall) that consists of up to 25 sets of this display (up to 5-sets each on the vertical and horizontal side). This function requires a daisy-chain connection. Tiling H monitors V monitors Position Frame comp. Enable Switch on delay 1 1 1 No No Off Example: 2 x 2 screen matrix (4 displays) H monitors = 2 displays V monitors = 2 displays 1 2 3 4 H monitors V monitors Position Example: 5 x 5 screen matrix (25 displays) H monitors = 5 displays V monitors = 5 displays 1 2 6 7 3 4 8 9 5 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 H monitors V monitors Position • H monitors - Select the number of displays on the horizontal side. • V monitors - Select the number of displays on the vertical side. • Position - Select the position of this display in the screen matrix. • Frame comp. - Choose to turn the frame compensation function on or off. If selected {Yes}, the display will adjust the image to compensate for the width of the display bezels in order to accurately display the image. Frame comp. - On BDL4271VL / BDL4671VL / BDL5571VL 22 Frame comp. - Off • Enable: Choose to enable or disable the Tiling function. If enabled, the display will apply the settings in {H monitors}, {V monitors}, {Position}, and {Frame comp.}. • Switch on delay: Set the power-on delaying time (in seconds). The default option {Auto} allows a sequential powering-on for each display by their ID number when multiple displays are connected. The options are: {Off / Auto / 2, 4, 6, 8, 10, 20, 30, 40, 50} NOTE: The Tiling function will be disabled when the [ON/OFF] button for PIP is pressed. Heat status This function allows you to check the thermal status of the display at any time. Date and time Adjust the current date and time for the display’s internal clock. Date and time Year Month Day Hour Minute Daylight saving time Current date time 2012 . 08 . 04 20 : 20 : 17 Press [SET] to set clock 2012 08 04 20 20 1. Press [ ] button to enter the submenu. 2. Press [ ] or [ ] button to toggle between {Year}, {Month}, {Day}, {Hour}, {Minute}, and {Daylight saving time}. 3. Press [ ] or [ ] button to adjust all settings except {Daylight saving time}. 4. Press [SET] button to enter the {Daylight saving} submenu. 5. Press [ ] or [ ] button to select item, press [ ] or [ ] button to adjust. Schedule This function allows you to program up to 7 (seven) different scheduled time intervals for the display to activate. You can select: • The time for the display to turn on and turn off. • The days in a week for the display to activate. • Which input source the display will use for each scheduled activation period. NOTE: We recommend you to set up current date and time in the {Date and time} menu before using this function. 1. Press [SET] or [ ] button to enter the submenu. Schedule Today 1 2 3 4 5 7 6 2012 . 08 . 04 THU 20 : 19 : 55 On ＿ : ＿ ＿ : ＿ ＿ Every day Off Input Wed SAT MON THU SUN TUE FRI Every week 2. Press [ ] or [ ] button to select a schedule item (item number 1 ~ 7), and then press [ ] button to mark it the item number. Schedule Today 1 2 3 4 5 7 6 2012 . 08 . 04 THU 20 : 19 : 55 On ＿ : ＿ ＿ : ＿ ＿ Every day Off Input Wed SAT MON THU SUN TUE FRI Every week 4 1 3 2 3. Press [ ] or [ ] button to select the schedule: 1 Power-on schedule: Press [ ] or [ ] button to set the hour and minute for the display to turn on. 2 Power-off schedule: Press [ ] or [ ] button to set the hour and minute for the display to turn off. Select or leave an empty “__” for both the hour and minute slot if you do not want to use this power-on or power-off schedule. 3 Input-source selection: Press [ ] or [ ] button to select an input source. If no input source is selected, the input source will remain the same as last selected. 4 Date schedule: Press [ ] button to select which day in a week this schedule item will be take effect, and then press the [SET] button. 4. For additional schedule settings, press [EXIT], then repeat the steps above. A check mark in the box next to the number of the schedule item indicates that the selected schedule is in effect. NOTES: • The {Every day} selection in a schedule item takes priority over the other weekly schedules. • If the schedules overlap, the scheduled power-on time takes priority over scheduled power-off time. BDL4271VL / BDL4671VL / BDL5571VL 23 • If there are two schedule items programmed for the same time, the highest numbered schedule takes priority. For example, if schedule items #1 and #2 both set the display to power on at 7:00 AM and off at 5:00 PM, then only schedule item # 1 will take effect. Monitor ID Set the ID number for controlling the display via the RS232C connection. Each display must have a unique ID number when multiple sets of this display are connected. DDC/CI Choose to turn on or off the DDC/CI communication function. Select {On} for normal use. Smart power Set the display to reduce the power consumption automatically. The options are: {Off} / {Medium} / {High}. Auto signal detection Choose to let the display detect and display available signal sources automatically. • {On} - Set the display to display the image automatically once a signal is connected. • {Off} - Once a signal is connected, it can only be selected manually. OPS settings Set the OPS configuration under each power condition. • {Auto} - After selecting {Card OPS} for video source input, the OPS will be set to off when the display power is set to off, or set to on when the display power is set to on. When set to other video source inputs, the OPS will always be set to on. • {Always off} - The OPS will always be set to off. • {Always on} - The OPS will always be set to on. Advanced option reset Reset all settings in the Advanced option menu to factory preset values. 1. Press [SET] or [ ] button to enter the submenu. 2. Press [ ] or [ ] button to select {Reset} and press the [SET] button to restore settings to factory preset values. 3. Press the [EXIT] button or select {Cancel} and press the [SET] button to cancel and then return to the previous menu. Schecule Monitor ID DDC/CI Auto signal detection Off Off On Action Action Picture Screen Audio PIP Configuration1 Configuration2 Advanced option Smart power OPS settings Action Always on Advanced option reset BDL4271VL / BDL4671VL / BDL5571VL 24 5. Input Mode VGA Resolution: Standard Resolution Active Resolution Refresh Rate Pixel Rate Aspect Ratio Stand for Mode H Pixels V Lines VGA 640 480 60 Hz 25.175 MHz 4:3 Video Graphic Array 72 Hz 72 Hz 31.5 MHz 75 Hz 75 Hz 31.5 MHz WVGA 720 400 70 Hz 33.75 MHz 16:9 Wide Video Graphic Array SVGA 800 600 60 Hz 40 MHz 4:3 Super VGA 75 Hz 75 Hz 49.5 MHz XGA 1024 768 60 Hz 65 MHz 4:3 Extended Graphic Array 75 Hz 75 Hz 78.75 MHz WXGA 1280 768 60 Hz 79.5 MHz 5:3 Wide XGA WXGA 1280 800 60 Hz 79.5 MHz 16:10 Wide XGA SXGA 1280 960 60 Hz 108 MHz 4:3 Super XGA SXGA 1280 1024 60 Hz 108 MHz 5:4 Super XGA WXGA 1360 768 60 Hz 85.5 MHz 16:9 Wide XGA WXGA 1366 768 60 Hz 85.5 MHz 16:9 Wide XGA UXGA 1600 1200 60 Hz 162 MHz 4:3 Ultra XGA HD1080 1920 1080 60 Hz 148.5 MHz 16:9 HD1080 SDTV Resolution: Standard Resolution Active Resolution Refresh Rate Pixel Rate Aspect Ratio Stand for Mode H Pixels V Lines 480i 720 480 29.97 Hz 13.5 MHz 4:3 Modified NTSC Standard 480p 59.94 Hz 27 MHz 576i 720 480 25 Hz 13.5 MHz 4:3 Modified PAL Standard 576p 50 Hz 27 MHz HDTV Resolution: Standard Resolution Active Resolution Refresh Rate Pixel Rate Aspect Ratio Stand for Mode H Pixels V Lines 720p 1280 720 50 Hz 74.25 MHz 16:9 Normally DVB Mode 60 Hz 1080i 1920 1080 25 Hz 74.25 MHz 16:9 Normally ATSC Mode 30 Hz 1080p 1920 1080 50 Hz 148.5 MHz 16:9 Normally ATSC Mode 60 Hz • The PC text quality is optimum in HD 1080 mode (1920 x 1080, 60Hz). • Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows). • Check your PC instruction book for information about connecting your PC to a display. • If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5KHz (horizontal). In some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the [INPUT] button to enter the video mode. Also, make sure that the PC is connected. • When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections. • The display settings table complies to the IBM/VESA standards, and based on the analog input. • The DVI support mode is regarded as same to the PC support mode. • The best timing for the vertical frequency to each mode is 60Hz. BDL4271VL / BDL4671VL / BDL5571VL 25 6. Pixel Defect Policy We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees that any Plasma- & LCD- displays with an unacceptable number of defects will be repaired during the warranty period in line with your local guarantee conditions. This notice explains the different types of pixel defects and defines the acceptable defect level for the BDL4230E LCD screen. In order to qualify for repair under warranty, the number of pixel defects must exceed a certain level as shown in the reference table. If the LCD screen is within specification a warranty exchange / claim back will be refused. Additionally, because some types or combinations of pixel defects are more noticeable than others, Philips sets even higher quality standards for those. 6.1. Pixels and Sub-Pixels subpixel pixel A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and blue. Many pixels together form an image. When all sub-pixels of a pixel are lit, the three colored sub-pixels together appear as a single white pixel. When all are dark, the three colored sub-pixels together appear as a single black pixel. Other combinations of lit and dark sub-pixels appear as single pixels of other colors. 6.2. Types of Pixel Defects + Dot Definition Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several types of sub-pixel defects within each category. Dot definition = What is a defective “Dot”? : One or more defective, adjacent sub-pixel are defined as one “dot”. The no. of defective sub-pixels are not relevant to define a defective dot. This means that a defective dot can consist of one, two or three defective sub-pixels which can be dark or lit. R G B One dot = One Pixel; consists of three sub-pixels of Red, Green, and Blue. 6.3. Bright Dot Defects Bright dot defects appear as pixels or sub-pixels that are always lit or “on”. These are the examples of bright dot defects: One lit red, green or blue sub pixel Two adjacent lit sub pixels: Red + Blue = Purple Red + Green = Yellow Green + Blue = Cyan (Light Blue) Three adjacent lit sub pixels (one white pixel) BDL4271VL / BDL4671VL / BDL5571VL 26 6.4. Dark Dot Defects Black dot defects appear as pixels or sub-pixels that are always dark or “off”. These are the examples of black dot defects: One dark dot Two adjacent dark dots = 1 pair of dark dots Two dark dots, specifications defines the minimum distance between dark dots 6.5. Proximity of Pixel Defects Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the proximity of pixel defects. In the table below you can find specifications about: • Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots) • Minimum distance between dark dots • Total no. of all defective dots 6.6. Pixel Defect Tolerances In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD- display must have pixel or sub- pixel defects exceeding the tolerances listed in the following table. BRIGHT DOT EFFECT ACCEPTABLE LEVEL 1 lit sub pixel 2 BLACK DOT EFFECT ACCEPTABLE LEVEL 1 dark sub pixel 10 TOTAL DOT DEFECTS OF ALL TYPES 12 NOTE: * 1 or 2 adjacent sub pixel defects = 1 dot defect 6.7. MURA Dark spots or patches may occasionally appear on some liquid crystal display (LCD) panels. This is known within the industry as Mura, which is a Japanese term for “unevenness.” It is used to describe an irregular pattern or area in which uneven screen uniformity appears under certain conditions. Mura is a result of the deterioration of the liquid crystal alignment layer and is most commonly caused by long-term operation under high ambient temperatures. It is an industry- wide phenomenon and Mura is not repairable. It is also not covered by our warranty terms. Mura has been around since the introduction of LCD technology and with screens getting bigger and in operation 24/7, many displays are running in low light conditions. This all adds to the possibility of Mura affecting displays. HOW TO SPOT MURA There are many symptoms of Mura and also multiple causes. Several of these are listed below: • Impurities or foreign particles in the crystal matrix • Uneven distribution of LCD matrix during manufacturing • Non-uniform luminance distribution of the backlight • Panel assembly induced stress • Flaws within the LCD cells • Thermal induced stress - high temperature operation over long periods of time HOW TO AVOID MURA Although we can not guarantee the complete eradication of Mura every time, in general the appearance of Mura can be minimized by these methods: • Lower the backlight brightness • Use a screen saver • Reduce the ambient temperature around the unit BDL4271VL / BDL4671VL / BDL5571VL 27 7. Cleaning and Troubleshooting 7.1. Cleaning Caution When Using the Display • Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too close. Placing any object near the top of the display could also result in heat related damage to the object as well as the display itself. • Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the cables and thus cause fire or electric shock. • Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure. Front Panel Cleaning Instructions • The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth or a soft, lint-free cloth. • If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to remove excess liquid. Wipe the surface of the display to remove dirt. Then use a dry cloth of the same type to dry. • Do not scratch or hit the surface of the panel with fingers or hard objects of any kind. • Do not use volatile substances such as insert sprays, solvents and thinners. Cabinet Cleaning Instructions • If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth. • If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to remove as much moisture as possible. Wipe the cabinet. Use another dry cloth to wipe over until the surface is dry. • Do not allow any water or detergent to come into contact with the surface of the display. If water or moisture gets inside the unit, operating problems, electrical and shock hazards may result. • Do not scratch or hit the cabinet with fingers or hard objects of any kind. • Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet. • Do not place anything made from rubber or PVC near the cabinet for any extended periods of time. BDL4271VL / BDL4671VL / BDL5571VL 28 7.2. Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 2. The main power switch on the back of the display is not switched on. 3. The selected input has no connection. 4. The display is in standby mode. 1. Plug in the power cord. 2. Make sure the power switch is switched on. 3. Connect a signal connection to the display. Interference displayed on the display or audible noise is heard Caused by surrounding electrical appliances or fluorescent lights. Move the display to another location to see is the interference is reduced. Color is abnormal The signal cable is not connected properly. Make sure that the signal cable is attached firmly to the back of the display. Picture is distorted with abnormal patterns 1. The signal cable is not connected properly. 2. The input signal is beyond the capabilities of the display. 1. Make sure that the signal cable is attached firmly. 2. Check the video signal source to see if it is beyond the range of the display. Please verify its specifications with this display’s specification section. Display image doesn’t fill up the full size of the screen The zoom mode is not correctly set. Use the Zoom mode or Custom zoom function in the Screen menu to fine tune display geometry and time frequency parameter. Can hear sound, but no picture Improperly connected source signal cable. Make sure that both video inputs and sound inputs are correctly connected. Can see picture but no sound is heard 1. Improperly connected source signal cable. 2. Volume is turned all the way down. 3. [MUTE] is turned on. 4. No external speaker connected. 1. Make sure that both video inputs and sound inputs are correctly connected. 2. Press [VOL UP] or [VOL DOWN] button to hear sound. 3. Switch MUTE off by using the [MUTE] button. 4. Connect external speakers and adjust the volume to a suitable level. Some picture elements do not light up Some pixels of the display may not turn on. This display is manufactured using an extremely high level of precision technology: however, sometimes some pixels of the display may not display. This is not a malfunction. After-Images can still be seen on the display after the display is powered off. (Examples of still pictures include logos, video games, computer images, and images displayed in 4:3 normal mode) A still picture is displayed for an over extended period of time Do not allow a still image to be displayed for an extended period of time as this can cause a permanent after-image to remain on the display. BDL4271VL / BDL4671VL / BDL5571VL 29 8. Technical Specifications 8.1. BDL4271VL Display: Item Specifications Screen Size (Active Area) 42” LCD Aspect Ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.4845 (H) x 0.4845 (V) [mm] Displayable colors 1073M colors Brightness (typical) 700 cd/m2 Contrast ratio (typical) 4000:1 Viewing angle 178 degrees In/Out Terminals: Item Specifications Speaker Output Internal Speakers External Speakers 10W (L) + 10W (R) [RMS]/8Ω 1 Way 1 Speaker System 82 dB/W/M/160 Hz ~ 13 KHz Audio Output RCA Jack x 2 0.5V [rms] (Normal) / 2 Channel (L+R) Audio Input RCA Jack x 2 3.5 mm Stereo x 1 0.5V [rms] (Normal) / 2 Channel (L+R) RS232C D-Sub Jack x 2 (9 pin) TXD + RXD (1:1) RJ-45 RJ-45 Jack x 1 (8 pin) 10/100 LAN Port HDMI Input HDMI Jack x 1 (Type A) (18 pin) Digital RGB: TMDS (Video + Audio) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R) Supports LPCM only DVI-D Input DVI-D jack Digital RGB: TMDS (Video) VGA Input D-Sub Jack x 1 (15 pin) Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) DVI-I (DVI-D & VGA) Output DVI-I Jack x 1 (29 pin) Digital RGB: TMDS (Video) Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Component Input BNC Jack x 3 Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω) MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p Displayport Input Displayport Jack x 1 (20 pin) Digital RGB: TMDS (Video + Audio) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R) Supports LPCM only USB Input USB Jack x 1 USB 2.0 USB Flash device (Picture, Audio, Video) General: Item Specifications Power Supply AC 100 ~ 240V, 50 ~ 60Hz Power Consumption (Max) 200W Power Consumption (typ.) 170W Power Consumption (Standby & Off) <1W (RS232 in active) Dimensions (With Stand) [W x H x D] 965.8 x 601.4 x 400 mm BDL4271VL / BDL4671VL / BDL5571VL 30 Dimensions (Without Stand) [W x H x D] 965.8 x 558.8 x 69 mm Weight (With Stand) 20.3 Kg Weight (Without Stand) 18.3 Kg Gross Weight (Without Stand) 23.8 Kg Environmental Condition: Item Specifications Temperature Operational 0 ~ 40°C Storage -20 ~ 60°C Humidity Operational 20 ~ 80% RH (No condensation) Storage 5 ~ 95% RH (No condensation) Altitude Operational 0 ~ 3,000 m Storage / Shipment 0 ~ 9,000 m Internal Speaker: Item Specifications Type 1 Way 1 Speaker Input 10 W (RMS) Impedance 8Ω Output Sound Pressure 82 dB/W/M Frequency Response 160 Hz ~ 13 KHz BDL4271VL / BDL4671VL / BDL5571VL 31 8.2. BDL4671VL Display: Item Specifications Screen Size (Active Area) 46” LCD Aspect Ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.17675 (H) x 0.53025 (V) [mm] Displayable colors 1073.7M colors Brightness (typical) 700 cd/m2 Contrast ratio (typical) 4000:1 Viewing angle 178 degrees In/Out Terminals: Item Specifications Speaker Output Internal Speakers External Speakers 10W (L) + 10W (R) [RMS]/8Ω 1 Way 1 Speaker System 82 dB/W/M/160 Hz ~ 13 KHz Audio Output RCA Jack x 2 0.5V [rms] (Normal) / 2 Channel (L+R) Audio Input RCA Jack x 2 3.5 mm Stereo x 1 0.5V [rms] (Normal) / 2 Channel (L+R) RS232C D-Sub Jack x 2 (9 pin) TXD + RXD (1:1) RJ-45 RJ-45 Jack x 1 (8 pin) 10/100 LAN Port HDMI Input HDMI Jack x 1 (Type A) (18 pin) Digital RGB: TMDS (Video + Audio) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R) Supports LPCM only DVI-D Input DVI-D jack Digital RGB: TMDS (Video) VGA Input D-Sub Jack x 1 (15 pin) Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) DVI-I (DVI-D & VGA) Output DVI-I Jack x 1 (29 pin) Digital RGB: TMDS (Video) Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Component Input BNC Jack x 3 Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω) MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p Displayport Input Displayport Jack x 1 (20 pin) Digital RGB: TMDS (Video + Audio) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R) Supports LPCM only USB Input USB Jack x 1 USB 2.0 USB Flash device (Picture, Audio, Video) General: Item Specifications Power Supply AC 100 ~ 240V, 50 ~ 60Hz Power Consumption (Max) 200W Power Consumption (typ.) 170W Power Consumption (Standby & Off) <1W (RS232 in active) Dimensions (With Stand) [W x H x D] 1052.7 x 662.7 x 400 mm Dimensions (Without Stand) [W x H x D] 1052.7 x 607.3 x 69 mm Weight (With Stand) 24.0 Kg BDL4271VL / BDL4671VL / BDL5571VL 32 Weight (Without Stand) 22.0 Kg Gross Weight (Without Stand) 27.5 Kg Environmental Condition: Item Specifications Temperature Operational 0 ~ 40°C Storage -20 ~ 60°C Humidity Operational 20 ~ 80% RH (No condensation) Storage 5 ~ 95% RH (No condensation) Altitude Operational 0 ~ 3,000 m Internal Speaker: Item Specifications Type 1 Way 1 Speaker Input 10 W (RMS) Impedance 8Ω Output Sound Pressure 82 dB/W/M Frequency Response 160 Hz ~ 13 KHz BDL4271VL / BDL4671VL / BDL5571VL 33 8.3. BDL5571VL Display: Item Specifications Screen Size (Active Area) 55” LCD Aspect Ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.21 (H) x 0.63 (V) [mm] Displayable colors 1073.7M colors Brightness (typical) 700 cd/m2 Contrast ratio (typical) 4000:1 Viewing angle 178 degrees In/Out Terminals: Item Specifications Speaker Output Internal Speakers External Speakers 10W (L) + 10W (R) [RMS]/8Ω 1 Way 1 Speaker System 82 dB/W/M/160 Hz ~ 13 KHz Audio Output RCA Jack x 2 0.5V [rms] (Normal) / 2 Channel (L+R) Audio Input RCA Jack x 2 3.5 mm Stereo x 1 0.5V [rms] (Normal) / 2 Channel (L+R) RS232C D-Sub Jack x 2 (9 pin) TXD + RXD (1:1) RJ-45 RJ-45 Jack x 1 (8 pin) 10/100 LAN Port HDMI Input HDMI Jack x 1 (Type A) (18 pin) Digital RGB: TMDS (Video + Audio) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R) Supports LPCM only DVI-D Input DVI-D jack Digital RGB: TMDS (Video) VGA Input D-Sub Jack x 1 (15 pin) Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) DVI-I (DVI-D & VGA) Output DVI-I Jack x 1 (29 pin) Digital RGB: TMDS (Video) Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω) MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Component Input BNC Jack x 3 Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω) MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p Displayport Input Displayport Jack x 1 (20 pin) Digital RGB: TMDS (Video + Audio) MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R) Supports LPCM only USB Input USB Jack x 1 USB 2.0 USB Flash device (Picture, Audio, Video) General: Item Specifications Power Supply AC 100 ~ 240V, 50 ~ 60Hz Power Consumption (Max) 275W Power Consumption (typ.) 245W Power Consumption (Standby & Off) <1W (RS232 in active) Dimensions (With Stand) [W x H x D] 1244.4 x 770.6 x 400 mm Dimensions (Without Stand) [W x H x D] 1244.4 x 715.2 x 69 mm Weight (With Stand) 32.6 Kg BDL4271VL / BDL4671VL / BDL5571VL 34 Weight (Without Stand) 30.6 Kg Gross Weight (Without Stand) 36.1 Kg Environmental Condition: Item Specifications Temperature Operational 0 ~ 40°C Storage -20 ~ 60°C Humidity Operational 20 ~ 80% RH (No condensation) Storage 5 ~ 95% RH (No condensation) Altitude Operational 0 ~ 3,000 m Internal Speaker: Item Specifications Type 1 Way 1 Speaker Input 10 W (RMS) Impedance 8Ω Output Sound Pressure 82 dB/W/M Frequency Response 160 Hz ~ 13 KHz 2012 © Koninklijke Philips Electronics N.V. All rights reserved. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips Electronics N.V. and are used under license from Koninklijke Philips Electronics N.V. Specifications are subject to change without notice. 家电维修资料网    www.520101.com                    免费下载各类电器说明书  www.520101.com  家电维修资料网    www.520101.com                    免费下载各类电器说明书  www.520101.com